Specifications are subject to change without notice.
© 2017 VTech Communications, Inc. All rights reserved.
12/17. VM351_QSG_V2.
Document order number: 96-011932-020-100
Basic operation - Parent unit
Adjust speaker volume
Press or to adjust your parent unit
speaker volume. It determines the volume of sound
transmitted from your baby unit.
Zoom
Press to zoom in or out.
Talk to your baby unit
Press and hold TALK and speak to your parent unit.
Your voice is transmitted to the baby unit.
Use the menu
Press MENU/SELECT to enter the menu, choose
a menu item, or save a setting. You can use
the parent unit menu for the advanced settings
or operations, such as to play or stop the baby
unit lullaby, or to adjust the baby unit sound
sensitivity.
While in the menu:
Press or to scroll up or down.
Press to select an item.
Press to return to the main menu or idle
screen.
•
•
•
Overview - Parent unit Overview - Baby unit
Adjust speaker volume
Press +
VOL
- to adjust your baby unit speaker
volume. It determines the lullaby volume and
talkback volume transmitted from your parent unit.
Turn off the baby unit
Slide the ON/OFF switch to OFF to power off
your baby unit.
Lullaby
Press /
to play lullaby on the baby unit.
Press to to play the next lullaby.
Press /
again to stop the lullaby.
•
•
Basic operation - Baby unit
Turn off the screen
Press and hold LCD ON/OFF to switch off the
screen. You can still hear sound from the baby
unit.
Skip
+
VOL
-
ON/OFF switch
Temperature
sensor
Speaker
Camera
Light sensor
Infrared LEDs
Play/Stop
Microphone
ON/OFF LED light
Insert the screws into the
holes and tighten the screws
until only 1/4 inch of the
screws are exposed.
If you drill the holes into a stud,
go to step 3.
-OR-
If you drill the holes into an object
other than a stud, insert the wall
anchors into the holes. Tap gently
on the ends with a hammer until
the wall anchors are flush with
the wall.
Mount the baby monitor (optional)
OR
Place the wall mount bracket on a
wall and then use a pencil to mark
the top and the bottom holes as
shown. Remove the wall mount
bracket and drill two holes in the
wall (7/32 inch drill bit).
Check for reception strength and
camera angle before drilling the holes.
•
Align the wall mount bracket and
screws with the holes in the wall
as shown. Tighten the screw in the
middle hole first, so that the wall
mount bracket position is fixed.
You can tighten the other screw in
the top hole.
Place the baby unit on the wall
mount bracket. Tighten the screw
into the threaded socket at the
bottom to secure the baby unit.
The default angle of the wall mount bracket is 90 degrees. You
can maximize your baby unit’s viewing angles by tilting the wall
mount bracket.
Hold the baby unit, and then rotate the knob in anticlockwise
direction. This will loosen the joint of the wall mount bracket.
Tilt your baby unit up or down to adjust to your preferred angle.
Then, rotate the knob in clockwise direction to tighten the joint
and secure the angle.
Place the baby unit on the wall mount
bracket. Tighten the screw into the
threaded socket at the bottom to secure the
baby unit. Align the holes on the wall mount
bracket with the screws on the wall, and
slide the wall mount bracket down until it
locks into place.
Turn off the parent unit
Press and hold POWER to power off your parent unit.
Press and hold
POWER
TALK
Zoom
Microphone
LED lights
Arrow keys
MENU
/
SELECT
Volume
VIEW / LCD ON/OFF
Antenna
Stand
Power jack
Speaker
Battery compartment
cover
Long press
Press any keys on the parent unit to turn on the
screen again.
•
Al
ert
T
on
e
Lo
w
B
attery To
ne
N
o
L
in
k
A
l
e
rt
So
un
d
aler
t
in
s
p
li
t
-
view
Long press
Threaded socket
Power Jack