Simplicity 030358-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030358-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Printed in U.S.A. Manual No. 204330GS Revision D (06/04/2009)

Portable Generator

Operator’s Manual

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WISCONSIN, U.S.A.

This generator is rated and certified to be compliant with CSA (Canadian

Standards Association) standard C22.2 No. 100-04 (motors and generators).

2 BRIGGSandSTRATTON.COM

Briggs & Stratton Power Products Group, LLC

900 North Parkway

Jefferson, WI 53549

material may be reproduced or transmitted in any form by

any means without the express written permission of Briggs

& Stratton Power Products Group, LLC.

Thank you for purchasing this quality-built Briggs & Stratton generator. We are pleased that you’ve placed your confidence in

the Briggs & Stratton brand. When operated and maintained according to the instructions in this manual, your Briggs &

Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generator products and

how to avoid them. This generator is designed and intended only for supplying electrical power for operating compatible

electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is important that you read

and understand these instructions thoroughly before attempting to start or operate this equipment. Save these instructions for

future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for instructions on final

assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow Pages. There

are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service. You can also contact

Briggs & Stratton Customer Service by phone at (800) 743-4115 or on the Internet at BRIGGSandSTRATTON.COM.

Generator

Model Number

Revision

Serial Number

Engine

Model Number

Type Number

Code Number

Date Purchased

Table of Contents

Operator Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Equipment Description. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Important Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpack Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Install Wheel Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Verify Engine Oil Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Add Fuel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Attach Negative Battery Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

System Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Connecting to a Building’s Electrical System. . . . . . . . . . . . . . . . . . . . . . . . 9

Generator Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Features and Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Cord Sets and Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Battery Float Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Connecting Electrical Loads. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Stopping the Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Warm Weather Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Don’t Overload Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Maintenance Schedule. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Generator Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Battery Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

StatStation™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Engine Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Schematic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Warranties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Emissions Control System Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Generator Owner Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Product Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Common Service Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Operator Safety

Equipment Description

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generator is an engine–driven, revolving field, alternating

current (AC) generator. It was designed to supply electrical

power for operating compatible electrical lighting, appliances,

tools and motor loads. The generator’s revolving field is

driven at about 3,600 rpm by a single-cylinder engine.

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

Every effort has been made to ensure that the information in

this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the generator and this documentation at any time

without prior notice.

The Emission Control System for this generator is warranted

for standards set by the Environmental Protection Agency

and the California Air Resources Board.

Important Safety Information

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that it

is safe for you and others. You must also make sure that the

procedure, work method or operating technique that you

choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol may

be used to represent the type of hazard. The signal word

NOTICE is used to address practices not related to personal

injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided,

could result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE address practices not related to personal injury.

4 BRIGGSandSTRATTON.COM

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

WARNING Running engine gives off carbon

monoxide, an odorless, colorless, poison gas.

Breathing carbon monoxide can cause headache,

fatigue, dizziness, vomiting, confusion, seizures,

nausea, fainting or death.

• Operate generator ONLY outdoors.

• Install a battery operated carbon monoxide alarm near the

bedrooms.

• Keep exhaust gas from entering a confined area through

windows, doors, ventilation intakes, or other openings.

• DO NOT start or run engine indoors or in an enclosed area,

(even if windows and doors are open), including the generator

compartment of a recreational vehicle (RV).

WARNING The engine exhaust from this product

contains chemicals known to the State of California to

cause cancer, birth defects, or other reproductive harm.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects or other

reproductive harm. Wash hands after handling.

WARNING

Generator produces hazardous voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING

• This generator does not meet U. S. Coast Guard Regulation

33CFR-183 and should not be used on marine applications.

• Failure to use the appropriate U. S. Coast Guard approved

generator could result in death or serious injury and/or

property damage.

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING OR DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are in

place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• This generator is not for use in mobile equipment or marine

applications.

WHEN TRANSPORTING, MOVING OR REPAIRING EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel shutoff

valve OFF.

• DO NOT tip engine or equipment at angle which causes fuel to

spill.

• Disconnect spark plug wire.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other ignition

source because they can ignite fuel vapors.

6 BRIGGSandSTRATTON.COM

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

NOTICE

Improper treatment of generator can damage it

and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or contact

local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and disconnect them

from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

WARNING Starter and other rotating parts can

entangle hands, hair, clothing, or accessories.

• NEVER operate generator without protective housing or covers.

• DO NOT wear loose clothing, jewelry or anything that may be

caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION

Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Assembly

Your generator requires some assembly and is ready for use

after it has been properly serviced with the recommended

fuel and oil.

If you have any problems with the assembly of your generator,

please call the generator helpline at (800) 743-4115. If calling

for assistance, please have the model, revision, and serial

number from the identification label available. See Generator

Controls and Features for identification label location.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner from

top to bottom.

4. Leave generator on carton to install wheel kit.

The generator is supplied with:

• Operator’s manual

• Battery float charger

• Wheel kit

Install Wheel Kit

NOTICE Wheel kit is not intended for over-the-road use.

You will need the following tools to install these

components:

• 13 mm wrench

• Socket wrench with 13 mm socket

• Pliers

• Safety glasses

Install the wheel kit as follows:

1. Tip generator so that engine end is up.

2. Slide axle (A) through both mounting brackets.

3. Place a wheel (B) on each side as shown below.

4. Place a washer (C) on axle and then place an e-ring (D)

in axle groove.

5. Install e-ring with pliers, squeezing from top of e-ring

to bottom of axle.

6. Repeat steps 4 and 5 to secure second wheel.

7. Tip generator so that engine side is down.

8. Remove existing locknut from left unit vibration mount

with 13 mm wrench. Use same locknut to attach

support leg (E).

9. Attach other side of support leg with a M8 x 20 mm

capscrew (F) and M8 lock nut (G).

10. Center lifting handle (H) on generator end of cradle.

Attach handle using two 13 mm wrenches with 45 mm

capscrews (J) and M8 lock nuts (K).

11. Return generator to normal operating position (resting

on wheels and support leg).

CAUTION

E-rings can cause eye injury.

E-rings can spring back and become airborne

when installing or removing.

• Always wear eye protection when installing/removing e-rings.

Verify Engine Oil Level

The generator engine is shipped from the factory filled with

oil (API SJ or higher 10W-30). This allows for generator

operation in the widest range of temperature and climate

conditions. Before starting the engine, check oil level and

ensure that engine is serviced as described in Maintenance.

NOTICE Any attempt to crank or start the engine before it

has been properly filled with the recommended oil will

result in equipment failure.

• Refer to Maintenance for oil fill information.

• Damage to equipment resulting from failure to follow this

instruction will void warranty.

NOTICE See Oil in the Maintenance section to review oil

recomendations. Verify provided oil in engine is the correct

viscosity for current ambient temperature.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). High

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) or up to

15% MTBE (methyl tertiary butyl ether) is acceptable.

NOTICE Avoid generator damage.

Failure to follow Operator’s Manual for fuel

recommendations voids warranty.

• DO NOT use unapproved gasoline such as E85.

• DO NOT mix oil in gasoline.

• DO NOT modify engine to run on alternate fuels.

To protect the fuel system from gum formation, mix in a fuel

stabilizer when adding fuel. See Storage. All fuel is not the

same. If you experience starting or performance problems after

using fuel, switch to a different fuel provider or change brands.

This engine is certified to operate on gasoline. The emission

control system for this engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded gasoline (A) to fuel tank (B). Be

careful not to overfill. Allow about 1.5" (4 cm) of tank

space (C) for fuel expansion.

3. Install fuel cap and let any spilled fuel evaporate before

starting engine.

High Altitude

At altitudes over 5,000 feet (1524 meters), a minimum

85 octane / 85 AKI (89 RON) gasoline is acceptable. To

remain emissions compliant, high altitude adjustment is

required. Operation without this adjustment will cause

decreased performance, increased fuel consumption, and

increased emissions. See an authorized dealer for high

altitude adjustment information. Operation of the engine at

altitudes below 2,500 feet (762 meters) with the high altitude

kit is not recommended.

Attach Negative Battery Cable

Your unit is equipped with electric start capability, but can be

started manually. If you choose not to use the electric start

feature, you do not need to connect the negative battery

cable.

The sealed battery on the generator pre–installed except for

the negative (black) battery cable.

To install:

1. Cut off tie wrap securing loose end of negative (black)

cable.

2. Remove screw (D), lock washer (E) and flat washer (F)

on negative battery terminal.

3. Slide lock washer, flat washer and negative battery

cable (G) over screw.

4. Reattach screw to negative battery terminal and tighten.

8 BRIGGSandSTRATTON.COM

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN ADDING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

5. Verify that connections to battery and generator are

tight and secure.

NOTICE Charge prior to use following the instructions in

the section Battery Float Charger.

System Ground

The generator has a system ground that connects the

generator frame components to the ground terminals on the

AC output receptacles. The system ground is connected to

the AC neutral wire (the neutral is bonded to the generator

frame).

Special Requirements

There may be Federal or State Occupational Safety and

Health Administration (OSHA) regulations, local codes, or

ordinances that apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

• In some areas, generators are required to be registered

with local utility companies.

• If the generator is used at a construction site, there

may be additional regulations which must be observed.

Connecting to a Building’s Electrical System

Connections for standby power to a building’s electrical

system must be made by a qualified electrician. The

connection must isolate the generator power from utility

power or other alternative power sources and must comply

with all applicable laws and electrical codes.

Generator Location

Clearances and Air Movement

Place generator outdoors in an area that will not accumulate

deadly exhaust gas. DO NOT place generator where exhaust

gas (A) could accumulate and enter inside or be drawn into a

potentially occupied building. Ensure exhaust gas is kept

away from any windows, doors, ventilation intakes, or other

openings that can allow exhaust gas to collect in a confined

area. Prevailing winds and air currents should be taken into

consideration when positioning generator.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

WARNING

Generator produces hazardous voltage.

Failure to isolate generator from power utility can

result in death or injury to electric utility workers

due to backfeed of electrical energy.

• When using generator for backup power, notify utility company.

Use approved transfer equipment to isolate generator from

electric utility.

• Use a ground fault circuit interrupter (GFCI) in any damp or

highly conductive area, such as metal decking or steel work.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are worn,

frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing in

water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate or

service generator.

WARNING Exhaust heat/gases can ignite

combustibles, structures or damage fuel tank

causing a fire.

• Keep at least 5 ft. (152 cm) clearance on all sides of generator

including overhead.

10 BRIGGSandSTRATTON.COM

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls and

adjustments. Save this manual for future reference.

A - Choke Lever — Used when starting a cold engine.

B - Air Cleaner — Protects engine by filtering dust and

debris out of intake air.

C - Start Button — Push and hold in start position for a

maximum of 15 seconds during each start attempt, until

engine starts.

D - Battery Float Charger Jack — Use battery float charger

to keep the starting battery charged and ready for use.

E - Recoil Starter — Used to start the engine.

F - Engine Rocker Switch — Set this switch to “On” before

using recoil starter. Set switch to “Off” to stop engine.

G - 120 Volt AC, 20 Amp, Duplex Receptacles — May be

used to supply electrical power for the operation of

120 Volt AC, 20 Amp, single phase, 60 Hz electrical,

lighting, appliance, tool, and motor loads.

H - 120/240 Volt AC, 30 Amp Locking Receptacle — May

be used to supply electrical power for the operation of

120 and/or 240 Volt AC, 30 Amp, single phase, 60 Hz

electrical, lighting, appliance, tool and motor loads.

J - Circuit Breakers (AC) — The 120 Volt AC, 20A duplex

receptacles are provided with "push to reset" circuit

breakers to protect the generator against electrical overload.

K - Identification Label — Provides model, revision, and

serial number of generator. Please have these readily

available when calling for assistance.

L - Grounding Fastener — Consult your local agency having

jurisdiction for grounding requirements in your area.

M - StatStation™ — Displays the electrical load on

generator based on output frequency. It also has a built

in maintenance reminder.

N - Spark Arrester Muffler — Exhaust muffler lowers engine

noise and is equipped with a spark arrester screen.

P - Hour Meter — Displays and records how many hours

your generator has run (up to 9,999.9).

R - Double Pole Circuit Breaker (AC) — A double pole

circuit breaker is provided to protect all the receptacles

and generator against electrical overload.

S - Engine Identification — Provides model, type and code

of engine. Please have these readily available if calling for

assistance.

T - Fuel Valve — Used to turn fuel supply on and off to

engine.

U - Fuel Tank — Capacity of seven (7) U.S. gallons (26.5 L).

Items Not Shown:

Oil Drain Plug — Drain engine oil here.

Oil Fill Cap — Check and fill engine with oil here.

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded extension

cords with the generator’s 120 Volt duplex receptacle.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use

them. Extension cord sets used should be rated for 125 Volt

AC loads at 20 Amps or greater for most electrical devices.

Some devices, however, may not require this type of

extension cord. Check the operator’s manuals of those

devices for the manufacturer’s recommendations.

Keep extension cords as short as possible to minimize

voltage drop.

120/240 Volt AC, 30 Amp, Locking Receptacle

Use a NEMA L14-30 plug with this receptacle. Connect a

4-wire cord set rated for 250 Volt AC loads at 30 Amps (or

greater). You can use the same 4-wire cord if you plan to

run a 120 Volt load.

This receptacle powers 120/240 Volt AC, 60 Hz, single phase

loads requiring up to 6,200 watts of power (6.2 kW) at

25.8 Amps for 240 Volts or two independent 120 Volt loads

at 25.8 Amps each. The outlet is protected by a double pole

rocker switch circuit breaker.

NOTICE

Receptacles may be marked with rating value

greater than generator output capacity.

• NEVER attempt to power a device requiring more amperage than

generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload Generator.

120 Volt AC, 20 Amp, Duplex Receptacles

Both duplex receptacles are protected against overload by a

double pole rocker switch circuit breaker.

Use each receptacle to operate 120 Volt AC, single-phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4 kW) at

20 Amps of current. Use cord sets that are rated for 125 Volt

AC loads at 20 Amps (or greater). Inspect cord sets before

each use.

Battery Float Charger

Use battery float charger jack to keep the starting battery

charged and ready for use. Battery charging should be done

in a dry location, such as inside a garage.

1. Plug charger into unit’s “Battery Float Charger” jack,

which is located next to the start switch. Plug battery

charger into a 120 Volt AC wall receptacle.

2. Unplug charger from unit and wall outlet when

generator is being started and while it is in operation.

3. Keep this charger plugged in when generator is not in

use to prolong battery life. The charger has a built in

float equalizer and will not overcharge the battery, even

when plugged in for an extended period of time.

NOTICE See Battery Maintenance for additional information.

4-Wire Cord Set

240V

120V

W (Neutral)

X (Hot)

Y (Hot)

NEMA L14-30

Ground (Green)

WARNING

Overloaded electrical cords can overheat,

arc, and burn resulting in death, bodily injury,

and/or property damage.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

12 BRIGGSandSTRATTON.COM

Operation

Starting the Engine

NOTICE Always unplug the battery float charger before

starting the generator.

Disconnect all electrical loads from the generator. Use the

following start instructions:

1. Make sure unit is on a level surface.

NOTICE Failure to start and operate the unit on a level

surface will cause the unit not to start or shut down during

operation.

2. Turn the fuel valve to the “On” position. The fuel valve

handle should be vertical (pointing toward the ground)

for fuel to flow.

3. Push choke lever to “Choke” position ( ).

4. Push engine rocker switch to “On”.

5A. For electric starting, push and hold the start button in

start position until generator starts. To prolong the life

of starter components, DO NOT hold start button in

start position for more than 15 seconds, and pause for

at least 1 minute between starting attempts.

• If engine starts, proceed to step 7.

• If engine fails to start, proceed to step 6.

NOTICE If battery is discharged, use manual starting

instructions.

5B. For manual starting, grasp recoil handle and pull

slowly until slight resistance is felt. Then pull rapidly

one time only to start engine.

• If engine starts, proceed to step 7.

• If engine fails to start, proceed to step 6.

6. Move choke lever to “Half” choke position, and pull

recoil handle twice.

• If engine fails to start, repeat steps 5 thru 7.

7. Slowly move choke lever to “Run” position ( ). If

engine falters, move choke lever to “Half” choke

position until engine runs smoothly, and then to “Run”

position ( ).

NOTICE If engine floods, place choke lever in “Run”

position ( ) and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run, or if

unit shuts down during operation, make sure unit is on a

level surface and check for proper oil level in crankcase. This

unit may be equipped with a low oil protection device. If so,

oil must be at proper level for engine to start.

WARNING Starter cord kickback (rapid retraction) can

result in bodily injury. Kickback will pull hand and

arm toward engine faster than you can let go.

Broken bones, fractures, bruises, or sprains

could result.

• When starting engine, pull cord slowly until resistance is felt

and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices plugged in

and turned on.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

Connecting Electrical Loads

1. Let engine stabilize and warm up for a few minutes

after starting.

2. Plug in and turn on the desired 120 and/or 240 Volt AC,

single phase, 60 Hz electrical loads.

NOTICE

• DO NOT connect 240 Volt loads to the 120 Volt duplex

receptacles.

• DO NOT connect 3-phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See Don’t

Overload Generator.

NOTICE

Exceeding generators wattage/amperage capacity

can damage generator and/or electrical devices connected to

it.

• DO NOT exceed the generator’s wattage/amperage capacity. See

Don’t Overload Generator in the Operation section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator before

stopping generator.

Stopping the Engine

1. Turn OFF and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned ON.

2. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

3. Push engine rocker switch to “Off” position.

4. Move fuel valve to “Off” position.

Warm Weather Operation

This generator engine is equipped with WeatherGuard, an

innovative feature to prevent carburetor icing in cold weather

conditions. WeatherGuard has been engineered to operate in

all weather conditions. However, product performance can

be increased when operating the generator solely in warm

weather by removing the WeatherGuard shield (A).

Remove the two nuts (B) and loosen the fastener (C) as

shown. Store shield and fasteners for future cold weather

operation.

WARNING

Backfire, fire or engine damage could

occur.

• DO NOT stop engine by moving choke control to “Choke”

position

().

14 BRIGGSandSTRATTON.COM

Don’t Overload Generator

Capacity

You must make sure your generator can supply enough

rated (running) and surge (starting) watts for the items you

will power at the same time. Follow these simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items. This is

the amount of power your generator must produce to

keep your items running. See Wattage Reference Guide.

3. Estimate how many surge (starting) watts you will need.

Surge wattage is the short burst of power needed to

start electric motor-driven tools or appliances such as a

circular saw or refrigerator. Because not all motors start

at the same time, total surge watts can be estimated by

adding only the item(s) with the highest additional surge

watts to the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 3075

Highest Additional Surge Watts = 1800

Total Generator Output Required = 4875

Power Management

To prolong the life of your generator and attached devices, it

is important to take care when adding electrical loads to your

generator. There should be nothing connected to the

generator outlets before starting its engine. The correct and

safe way to manage generator power is to sequentially add

loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the largest

load you have.

3. Permit the generator output to stabilize (engine runs

smoothly and attached device operates properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity. Take

special care to consider surge loads in generator capacity, as

described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or Appliance

Rated (Running)

Watts

Additional Surge

(Starting) Watts

Window Air

Conditioner

1200 1800

Refrigerator 800 1600

Deep Freezer 500 500

Television 500 —

Light (75 Watts) 75 —

3075 Total

Running Watts

1800 Highest

Surge Watts

Wattage Reference Guide

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 —

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 cf 800 1600

Water Well Pump - 1/3 hp 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 hp 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 —

Coffee Maker 1500 —

Electric Stove - Single Element 1500 —

Hot Plate 2500 —

Family Room

DVD/CD Player 100 —

VCR 100 —

Stereo Receiver 450 —

Color Television - 27 in 500 —

Personal Computer w/17 in

monitor

800 —

Other

Security System 180 —

AM/FM Clock Radio 300 —

Garage Door Opener - 1/2 hp 480 520

Electric Water Heater - 40 gallon 4000 —

DIY/Job Site

Quartz Halogen Work Light 1000 —

Airless Sprayer - 1/3 hp 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 hp 1000 1000

Circular Saw - 7-1/4 in 1500 1500

Miter Saw - 10 in 1800 1800

Table Planer - 6 in 1800 1800

Table Saw/Radial Arm Saw - 10 in 2000 2000

Air Compressor - 1-1/2 hp 2500 2500

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever occurs

first. More frequent service is required when operating in

adverse conditions noted below.

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance and

extend the life of the generator. See an authorized dealer for

service.

The generator’s warranty does not cover items that have

been subjected to operator abuse or negligence. To receive

full value from the warranty, the operator must maintain the

generator as instructed in this manual.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least once

each season. Follow the requirements in the Maintenance

Schedule chart above.

NOTICE Once a year you should clean or replace the spark

plug and replace the air filter. A new spark plug and clean air

filter assure proper fuel-air mixture and help your engine run

better and last longer.

Emissions Control

Maintenance, replacement, or repair of the emissions

control devices and systems may be performed by any

non-road engine repair establishment or individual.

However, to obtain ”no charge” emissions control service,

the work must be performed by a factory authorized dealer.

See the Emissions Warranty.

Generator Maintenance

Generator maintenance consists of keeping the unit clean

and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive dust,

dirt, moisture, or any corrosive vapors. Cooling air slots in

the generator must not become clogged with snow, leaves,

or any other foreign material.

NOTICE DO NOT use water or other liquids to clean

generator. Liquids can enter engine fuel system, causing

poor performance and/or failure to occur. In addition, if

liquid enters generator through cooling air slots, some of the

liquid will be retained in voids and cracks of the rotor and

stator winding insulation. Liquid and dirt buildup on the

generator internal windings will eventually decrease the

insulation resistance of these windings.

Cleaning

Daily or before use, look around and underneath the

generator for signs of oil or fuel leaks. Clean accumulated

debris from inside and outside the generator. Keep the

linkage, spring and other engine controls clean. Inspect

cooling air slots and openings on generator. These openings

must be kept clean and unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE

Improper treatment of generator can damage it

and shorten its life.

• DO NOT expose generator to excessive moisture, dust, dirt, or

corrosive vapors.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt or oil.

• Use a vacuum cleaner to pick up loose dirt and debris.

Battery Maintenance

Other than float charging, described elsewhere, no

maintenance is required for the starting battery. Keep the

battery and terminals clean and dry.

NOTICE Battery charging should be performed in a dry

location, such as inside a garage.

First 5 Hours

• Change engine oil

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

Every 25 Hours or Yearly

• Service engine air cleaner

Every 50 Hours or Yearly

• Change engine oil

Every 100 Hours or Yearly

• Service spark plug

• Inspect muffler and spark arrester

• Clean cooling system

Every 250 Hours or Yearly

• Check valve clearance

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds - chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

16 BRIGGSandSTRATTON.COM

StatStation™

The StatStation™ displays the nominal load on generator

based on output frequency. It also has a built in maintenance

reminder.

Wattage Monitor Operation

The display is two seven-segment LEDs that provide an

easy-to-read indication of the amount of power being

supplied by the generator. The load monitor displays the

generator’s output as a percentage.

As generator load increases, the display values will increase.

When the displayed values begin flashing, the user should

stop adding electrical loads to the generator.

If the power usage becomes too high, the letters “OL” (for

Over Load) will flash on the display. The user should reduce

the amount of load attached to the generator.

Maintenance Reminder

The LED will display certain codes to alert you to check oil,

change oil, check or replace air filter and check or replace

spark plug. The following codes will display:

“C1” Check oil at 8 hour increments

“C2” Change oil at 50 hour increments

“C3” Check or replace air filter at 25 hour increments

“C4” Check or replace spark plug at 100 hour increments

To take advantage of the StatStation “maintenance reminder”

capabilities, the user must press the reset button after

completing the maintenance called for in the displayed code

(C1, C2, C3, or C4). This results in a display of “Co” or “CA”,

depending on how long the button is pressed:

1) “Co” - Pressing the reset button once quickly will

display "Co" (clearing to zero). This will clear any

maintenance codes that have elapsed up to that point

and they will begin timing again from zero.

2) “CA” - Pressing and holding the reset button for

2 seconds will display "CA" (clearing all). This clears all

maintenance codes, even if they have not yet reached

their service point, and they will begin timing again

from zero.

If nominal load and maintenance codes appear

simultaneously, the LED shall display, alternately, the

nominal load and code as follows:

The code will display for 3 seconds, then 1/2 second off. The

load will display for 6 seconds and then 1/2 second off.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity for

the engine. Use the chart to select the best viscosity for the

outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard starting.

** Above 80°F (27°C) the use of 10W30 may cause increased oil

consumption. Check oil level more frequently.

NOTICE Synthetic oil meeting ILSAC GF-2, API

certification mark and API service symbol with

“SJ/CF ENERGY CONSERVING” or higher, is an

acceptable oil at all temperatures. Use of synthetic

oil does not alter required oil change intervals.

WARNING Unintentional sparking can result in fire or

electric shock.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and place

the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Checking Oil Level

Oil level should be checked prior to each use or at least

every 8 hours of operation. Keep oil level maintained.

1. Make sure generator is on a level surface.

2. Clean area around oil fill and remove oil fill cap.

3. Verify oil is at the point of overflowing at oil fill opening.

4. Replace and tighten oil fill cap.

Adding Engine Oil

1. Make sure generator is on a level surface.

2. Check oil level as described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

point of overflowing at oil fill.

4. Replace and tighten oil fill cap.

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change the oil

more often.

KEEP OUT OF REACH OF CHILDREN. DON’T

POLLUTE. CONSERVE RESOURCES. RETURN

USED OIL TO COLLECTION CENTERS.

Change the oil while the engine is still warm from running,

as follows:

1. Make sure unit is on a level surface.

2. Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

3. Clean area around oil drain plug (A). The oil drain plug

is located at base of engine, opposite carburetor.

4. Remove oil drain plug and drain oil completely into a

suitable container.

5. Reinstall oil drain plug and tighten securely. Remove oil

fill cap.

6. Slowly pour oil (about 28 oz.) into oil fill opening (B) to

the point of overflowing (C) at oil fill cap. DO NOT overfill.

7. Reinstall oil fill cap. Finger tighten cap securely.

8. Wipe up any spilled oil.

Service Air Cleaner

Your engine will not run properly and may be damaged if

you run it with a dirty air cleaner. Replace more often if

operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen screws (D) and remove air cleaner cover (E).

2. Carefully remove cartridge (F) from base (G).

3. Install clean (or new) air cleaner assembly inside cover.

Dispose of old filter properly.

4. Assemble air cleaner cover onto base and tighten screws.

Service Spark Plug

Changing the spark plug will help your engine to start easier

and run better.

1. Clean area around spark plug.

2. Remove and inspect spark plug.

3. Check electrode gap with wire feeler gauge and reset

spark plug gap to recommended gap if necessary (see

Specifications).

4. Replace spark plug if electrodes are pitted, burned or

porcelain is cracked. Use the recommended

replacement spark plug. See Specifications.

5. Install spark plug and tighten firmly.

CAUTION Avoid prolonged or repeated skin contact

with used motor oil.

• Used motor oil has been shown to cause skin cancer in certain

laboratory animals.

• Thoroughly wash exposed areas with soap and water.

18 BRIGGSandSTRATTON.COM

Inspect Muffler and Spark Arrester

Inspect the muffler for cracks, corrosion, or other damage.

Remove the spark arrester, if equipped, and inspect for

damage or carbon blockage. If replacement parts are

required, make sure to use only original equipment

replacement parts.

Clean and inspect the spark arrester as follows:

1. To remove muffler heat shield (A) from muffler (B),

remove four screws that connect guard to muffler

bracket.

2. Remove four screws that attach spark arrester screen

(C).

3. Inspect screen and obtain a replacement if torn,

perforated or otherwise damaged. DO NOT use a

defective screen. If screen is not damaged, clean it with

commercial solvent.

4. Reattach screen and muffler guard.

Air Cooling System

Over time debris may accumulate in cylinder cooling fins and

cannot be observed without partial engine disassembly. For

this reason, we recommend you have an authorized service

dealer clean the cooling system (D) per recommended

intervals (see Maintenance Schedule in beginning of

Maintenance section). Equally important is to keep top of

engine free from debris. See Clean Debris.

Check Valve Clearance

Regular valve clearance check and adjustment will improve

performance and extend engine life. This procedure cannot

be done without partial engine disassembly and the use of

special tools. For this reason we recommend that you have

an authorized service dealer check and adjust valve clearance

at recommended intervals (see Maintenance Schedule in the

Maintenance section).

Carburetor Adjustment

The carburetor on this engine is low emission. It is equipped

with a non-adjustable idle mixture valve. Top speed has been

set at the factory. If adjustment is required, see an

authorized service dealer.

WARNING Contact with muffler area can result in

serious burns.

Exhaust heat/gases can ignite

combustibles, structures or damage

fuel tank causing a fire.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (152 cm) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in Section

4442, maintained in effective working order. Other states or

federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer, or dealer

to obtain a spark arrester designed for the exhaust system

installed on this engine.

• Replacement parts must be the same and installed in the same

position as the original parts.

CAUTION

Excessively high operating speeds increase

risk of injury and damage to generator.

Excessively low speeds impose a heavy load.

• DO NOT tamper with governed speed. Generator supplies

correct rated frequency and voltage when running at governed

speed.

• DO NOT modify generator in any way.

Storage

The generator should be started at least once every seven

days and allowed to run at least 30 minutes. If this cannot be

done and you must store the unit for more than 30 days, use

the following guidelines to prepare it for storage.

Generator Storage

• Clean the generator as outlined in Cleaning.

• Check that cooling air slots and openings on generator

are open and unobstructed.

Long Term Storage Instructions

Fuel can become stale when stored over 30 days. Stale fuel

causes acid and gum deposits to form in the fuel system or

on essential carburetor parts. To keep fuel fresh, use Briggs

& Stratton FRESH START® fuel stabilizer, available as a

liquid additive or a drip concentrate cartridge.

There is no need to drain gasoline from the engine if a fuel

stabilizer is added according to instructions. Run the engine

for 2 minutes to circulate the stabilizer throughout the fuel

system. The engine and fuel can then be stored up to

24 months.

If gasoline in the engine has not been treated with a fuel

stabilizer, it must be drained into an approved container. Run

the engine until it stops from lack of fuel. The use of a fuel

stabilizer in the storage container is recommended to

maintain freshness.

Change Engine Oil

While engine is still warm, drain oil from crankcase. Refill

with recommended grade. See Changing Engine Oil.

Other Storage Tips

1. DO NOT store fuel from one season to another unless it

has been treated as described in Long Term Storage

Instructions.

2. Replace fuel container if it starts to rust. Rust and/or

dirt in fuel can cause problems if it’s used with this

unit.

3. Cover unit with a suitable protective cover that does not

retain moisture.

4. Store generator in clean, dry area.

WARNING Fuel and its vapors are extremely

flammable and explosive.

Fire or explosion can cause severe burns

or death.

WHEN STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes dryers

or other appliances that have pilot light or other ignition source

because they can ignite fuel vapors.

WHEN DRAINING FUEL

• Turn generator OFF and let it cool at least 2 minutes before

removing fuel cap. Loosen cap slowly to relieve pressure in

tank.

• Drain fuel tank outdoors.

• Keep fuel away from sparks, open flames, pilot lights, heat, and

other ignition sources.

• DO NOT light a cigarette or smoke.

WARNING

Storage covers can be flammable.

• DO NOT place a storage cover over a hot generator.

• Let equipment cool for a sufficient time before placing the cover

on the equipment.

20 BRIGGSandSTRATTON.COM

Troubleshooting

Problem Cause Correction

Engine is running, but no AC

output is available.

1. One of the circuit breakers is open.

2. Fault in generator.

3. Poor connection or defective cord set.

4. Connected device is bad.

1. Reset circuit breaker.

2. Contact authorized service facility.

3. Check and repair.

4. Connect another device that is in good

condition.

Engine runs good at no-load but

“bogs down” when loads are

connected.

1. Short circuit in a connected load.

2. Engine speed is too slow.

3. Generator is overloaded.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. Contact authorized service facility.

3. See Don’t Overload Generator in

Operation section.

4. Contact authorized service facility.

Engine will not start; or starts

and runs rough.

1. Rocker switch set to “Off”.

2. Fuel Valve is in “Off” position.

3. Dirty air cleaner.

4. Out of fuel.

5. Stale fuel.

6. Spark plug wire not connected to spark

plug.

7. Bad spark plug.

8. Water in fuel.

9. Flooded.

10. Excessively rich fuel mixture.

11. Intake valve stuck open or closed.

12. Engine has lost compression.

1. Set switch to “On”.

2. Turn fuel valve to “On” position.

3. Clean or replace air cleaner.

4. Fill fuel tank.

5. Drain fuel tank and carburetor; fill with

fresh fuel.

6. Connect wire to spark plug.

7. Replace spark plug.

8. Drain gas tank and carburetor; fill with

fresh fuel.

9. Wait 5 minutes and re-crank engine.

10. Contact authorized service facility.

11. Contact authorized service facility.

12. Contact authorized service facility.

Engine shuts down when

running.

Out of fuel. Fill fuel tank.

Engine lacks power.

1. Load is too high.

2. Dirty air filter.

1. See Don’t Overload Generator in

Operation section.

2. Replace air filter.

Engine “hunts” or falters. Carburetor is running too rich or too lean. Contact authorized service facility.

La page charge ...

Simplicity 030358-0 Manuel utilisateur

Marque: Simplicity

Modèle: 030358-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 030358-0 User manual

Documents connexes

Autres documents

Briggs & Stratton 203985GS Manuel utilisateur