Trendnet RB-TPE-S160 Le manuel du propriétaire

Marque: Trendnet

Modèle: RB-TPE-S160

Catégorie: Commutateurs réseau

Taper: Le manuel du propriétaire

TPE-S160

1.01

Guide d'installation rapide

Table of Contents

Version 03.23.2010

Français 1

Technical Specifications 7

Troubleshooting 8

1. Avant de commencer 1

2. Voyants 2

3. Installation du matériel 3

1. Avant de commencer

Contenu de l'emballage

Vérification de l'équipement

ŸTPE-S160

ŸGuide d'installation rapide en plusieurs

langues

ŸCordon d'alimentation

ŸKit de montage

ŸPieds en caoutchouc

ŸUn ordinateur avec un adaptateur réseau correctement installé

ŸCâble réseau RJ-45

ŸLa surface sous le commutateur doit pouvoir résister à un poids minimum de 3.8kg

ŸLa prise secteur doit être située à un maximum de 1,82 mètres de l'appareil

ŸVérifiez la présence d'une source de ventilation adéquate autour du commutateur

pour une dissipation efficace de la chaleur

ŸNe placez pas d'objets lourds sur le commutateur.

ŸPériphérique alimenté par IEEE 802.3af

Équipement optionnel

Remarque:

Le TPE-S160 ne supporte que les péripériques alimentés qui respectent la norme

IEEE 802.3af

ŸTPE-112GS (non fourni)

ŸUn rack EIA standard 19 pouces (non fourni)

Link/ACT

PoE (Power over Ethernet)

Power

Voyant indiquant le

statut de l’appareil

Couleur

Séquence

Définition

PoE

(Power over Ethernet)

Power

Link/ACT

Jaune

Fixe

Clignotant

Jaune

Vert

N/A

Arrêt

N/A

PoE device is connected

Un périphérique PoE est connecté

Aucune connexion au port

Périphérique alimenté allumé

Périphérique alimenté éteint

100/200Mbps (Half/Full) ou 10/20 Mbps

(Half/Full Duplex) branché (par port)

Emission/réception de données

(par port)

2. Voyants

3. Installation du matériel

1. Branchez le Cordon électrique à l'arrière du

TPE-S160 et à une prise de courant.

2. Déplacer l'interrupteur d'alimentation en

position marche.

3. Branchez un câble réseau RJ-45 entre

l'ordinateur et un port Ethernet disponible sur le

TPE-S160.

4. Branchez un câble RJ-45 cable entre un port

PoE du TPE-S160 et le port LAN du

périphérique PoE (p. ex. le TEW-638PAP)

5. Vérifiez que les voyants suivants du panneau

sont allumés: Power, PoE et Link/ACT.

1. Sélectionnez le voltage adéquat (5V, 7.5V, 9V

ou 12V).

5. Vérifiez que les voyants suivants du panneau

sont allumés: Power, PoE Status et Link/ACT.

Utilisation du TPE-S160 et du TPE-112GS avec un périphérique non-POE

Remarque: Notez la puissance de sortie de votre périphérique non PoE.

Le TPE-112GS ne supporte que les périphériques non PoE avec une puissance de

sortie de 5V, 7,5V, 9V ou de 12V.

2. Branchez un câble Ethernet entre le port PoE

(1 à 4) du switch TPE-S160 et le port POE IN

du TPE-112GS.

4. Branchez le câble Jumper entre un

périphérique non PoE (p. ex. le TEW-637AP) et

le TPE-112GS.

3. Branchez une câble Ethernet entre le

périphérique non PoE et le port DATA OUT du

TPE-112GS.

Le Switch peut être installé dans un rack EIA standard de 19 pouces qui peut

être placé dans une armoire de répartition avec d'autres équipements.

Montage du rack

1. Attachez les supports de montage des deux

côtés du switch et fixez les avec les vis fournies.

2. Installez soigneusement le switch dans le rack.

Alignez le support sur les trous des vis du rack

et utilisez les vis fournies avec le matériel pour

installer le switch.

Technical Specifications

Hardware

Standard

ŸIEEE 802.3 10Base-T

ŸIEEE802.3u 100Base-TX

ŸIEEE 802.3af Power over Ethernet

ŸIEEE 802.3x Flow Control

16 x 10/100Mbps Auto-MDIX PoE ports

On/Off power switch

ŸEthernet: 10/20Mbps (half/full duplex)

ŸFast Ethernet: 100/200Mbps (half/full duplex)

1.5Mbits

4K MAC entries

3.2Gbps

100~240VAC 50/60Hz, internal universal switching power

Power, Link/Activity, PoE Act/Status

Ÿ6 Watts max. (no Power Device (PD) connected)

Ÿ260 Watts max. (16 PoE devices connected)

ŸOperating: 0° ~ 45°C (32° ~ 113°F)

ŸStorage: -10° ~ 70°C (14° ~ 158°F)

Ports

Power Switch

Data Transfer Rates

Data RAM Buffer

Address Table

Switch Fabric

Power

Diagnostic LEDs

Power Consumption

Temperature

10%- 95% (non-condensing)

440 x 220 x 44 mm (117.3 x 8.7 x 1.7 in.)

3.1 kg (6.9 lb)

CE, FCC

ŸUp to 15.4 watts per port; PD classification

ŸPolymer switch for short protection

ŸPoE: pin 3,6 for power (+) and pin 1,2 for power (-)

Humidity

Dimensions

Certifications

Weight

PoE

Power over Ethernet

Troubleshooting

1. After connecting the Switch to a power outlet, the LEDs do not turn on.

1. Check the connection of the power cord to the TPE-S160 and the power outlet.

2. Verify that the power switch is set to the On position.

3. Check that the power outlet is receiving power.

2. After I connect my PCs to the Switch, I am unable to share files.

1. Check the LEDs on the Switch. Make sure the Link/ACT LED is on.

2. Check the network cable. The minimum length of the cable is 1.5 meters and

the maximum length of the cable is 100 meters.

3. Disable any software firewall program.

4. Verify that you have file sharing enabled. Please contact your Operating

System support for more information.

3. After I connect my PCs to the Switch, I can only get onto the Internet from one

computer.

The Switch was not designed to share Internet between multiple computers. You

need to get an Internet router such as the TW100-S4W1CA.

4. My 802.3af Powered device does not power on when I plug the device into the

Switch. What should I do?

1. Verify that the PoE device supports IEEE 802.3af protocol.

2. Verify that the power switch is set to the on position.

3. Power cycle the PoE switch. Move the power switch to the off position. Wait 15

seconds, then move the power switch back to the on position.

4. Plug the device into a different port on the PoE switch.

5. Try using another RJ-45 network cable.

5. Where is the uplink port located on the Switch?

Since all the ports on the Switch are Auto-MDIX, any of the ports can be used as

an uplink port.

If you still encounter problems or have any questions regarding the TPE-S160 please

contact Trendnet's Technical Support Department.

Limited Warranty

TRENDnet warrants its products against defects in material and workmanship, under normal

use and service, for the following lengths of time from the date of purchase.

TPE-S160 – 3 Years Limited Warranty

AC/DC Power Adapter, Cooling Fan, and Power Supply carry a 1 year warranty.

If a product does not operate as warranted during the applicable warranty period, TRENDnet

shall reserve the right, at its expense, to repair or replace the defective product or part and deliver

an equivalent product or part to the customer. The repair/replacement unit's warranty continues

from the original date of purchase. All products that are replaced become the property of

TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue

refunds or credit. Please contact the point-of-purchase for their return policies.

TRENDnet shall not be responsible for any software, firmware, information, or memory data of

customer contained in, stored on, or integrated with any products returned to TRENDnet

pursuant to any warranty.

There are no user serviceable parts inside the product. Do not remove or attempt to service the

product by any unauthorized service center. This warranty is voided if (i) the product has been

modified or repaired by any unauthorized service center, (ii) the product was subject to accident,

abuse, or improper use (iii) the product was subject to conditions more severe than those

specified in the manual.

Warranty service may be obtained by contacting TRENDnet within the applicable warranty

period and providing a copy of the dated proof of the purchase. Upon proper submission of

required documentation a Return Material Authorization (RMA) number will be issued. An

RMA number is required in order to initiate warranty service support for all TRENDnet

products. Products that are sent to TRENDnet for RMA service must have the RMA number

marked on the outside of return packages and sent to TRENDnet prepaid, insured and

packaged appropriately for safe shipment. Customers shipping from outside of the USA and

Canada are responsible for return shipping fees. Customers shipping from outside of the

USA are responsible for custom charges, including but not limited to, duty, tax, and other

fees.

WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS

WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S

OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE

EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,

EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING

WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME

FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION

MAINTENANCE OR USE OF TRENDNET'S PRODUCTS.

TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND

EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT

EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT,

IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR

MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY

ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.

LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO

EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN

CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL,

INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE

OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER

FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION,

MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE

POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR,

REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION.

THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY

REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.

Governing Law: This Limited Warranty shall be governed by the laws of the state of California.

Some TRENDnet products include software code written by third party developers. These codes

are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License

("LGPL").

Go to or Download section and look for

the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are

distributed WITHOUT WARRANTY and are subject to the copyrights of the developers.

TRENDnet does not provide technical support for these codes. Please go to

or for specific terms of

each license.

http://www.trendnet.com/gpl http://www.trendnet.com

http://www.gnu.org/licenses/gpl.txt http://www.gnu.org/licenses/lgpl.txt

Trendnet RB-TPE-S160 Le manuel du propriétaire

Marque: Trendnet

Modèle: RB-TPE-S160

Catégorie: Commutateurs réseau

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Trendnet RB-TPE-S160 Owner's manual

Trendnet RB-TPE-S160 Le manuel du propriétaire

Trendnet RB-TPE-S160 Le manuel du propriétaire

dans d''autres langues

Documents connexes