Hilti ST 1800-A18 Mode d'emploi

Catégorie
Outils électroportatifs
Taper
Mode d'emploi
ST 1800A18
English en
Français fr
Español es
Português pt
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
1
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
2
3
4
5
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
6
7
8
9
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
10
11
12
13
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
ST 1800A18
en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
fr Mode d'emploi original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
1
1 Information about the documentation
1.1 Explanation of signs used
1.1.1 Warnings
Warnings alert persons to hazards that occur when handling or using the product. The following signal words
are used in combination with a symbol:
DANGER! Draws attention to imminent danger that will lead to serious personal injury or fatality.
WARNING! Draws attention to a potentially dangerous situation that could lead to serious per-
sonal injury or fatality.
CAUTION! Draws attention to a potentially dangerous situation that could lead to slight personal
injury or damage to the equipment or other property.
1.1.2 Symbols
The following symbols are used:
Read the operating instructions before use.
Instructions for use and other useful information
Forward / reverse
Rated speed under no load
Revolutions per minute
Revolutions per minute
1.1.3 Illustrations
The illustrations in these operating instructions are intended to convey a basic understanding and may differ
from the actual version of the product:
These numbers refer to the corresponding illustrations found at the beginning of these operating
instructions.
The numbering in the illustrations reflects the order of the work steps in the illustration and may
deviate from the numbering of work steps in the text.
Item reference numbers are used in the overview illustration. In the product overview section, the
numbers shown in the legend relate to these item reference numbers.
1.2 Information about the documentation
Read these operating instructions before the product is used or operated for the first time. This is a is a
prerequisite for safe, trouble-free handling and use of the product.
Observe the safety instructions and warnings printed in this documentation and on the tool.
Always keep the operating instructions with the tool and make sure that the operating instructions are
with the tool when it is given to other persons.
We reserve the right to make changes. Errors excepted.
1.3 Product information
Hilti products are designed for professional use and may be operated, serviced and maintained only by
trained, authorized personnel. This personnel must be informed of any particular hazards that may be
encountered. The product and its ancillary equipment may present hazards when used incorrectly by
untrained personnel or when used not as directed.
Make a note of the designation and serial number printed on the identification plate in the following table.
Always quote this information when you contact a Hilti representative or Hilti Service to make en enquiry:
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
2
Product information
Cordless metal screwdriver ST 1800A18
Generation 01
Serial no.
2 Safety
2.1 Safety instructions
The safety rules given in the following section contain all general safety rules for electric tools which, in
accordance with the applicable standards, require to be listed in the operating instructions. Accordingly,
some of the rules listed may not be relevant to this electric tool.
2.1.1 General power tool safety warnings
WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
Keep children and bystanders away while operating a power tool. Distractions can cause you to lose
control.
Electrical safety
Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the
risk of electric shock.
Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the
risk of electric shock.
When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of electric shock.
Personal safety
Stay alert, watch what you are doing and use common sense when operating a power tool. Do
not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A
moment of inattention while operating power tools may result in serious personal injury.
Use personal protective equipment. Always wear eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch is in the off‐position before connecting to power
source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on
the switch or energising power tools that have the switch on invites accidents.
Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance at all times. This enables better control of the
power tool in unexpected situations.
Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
3
If devices are provided for the connection of dust extraction and collection facilities, ensure these
are connected and properly used. Use of dust collection can reduce dust-related hazards.
Power tool use and care
Do not force the power tool. Use the correct power tool for your application. The correct power tool will
do the job better and safer at the rate for which it was designed.
Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool accidentally.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the
power tool or these instructions to operate the power tool. Power tools are dangerous in the hands
of untrained users.
Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and
any other condition that may affect the power tool’s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poorly maintained power tools.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking
into account the working conditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazardous situation.
Battery tool use and care
Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used with another battery pack.
Use power tools only with specifically designated battery packs. Use of any other battery packs may
create a risk of injury and fire.
When battery pack is not in use, keep it away from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a fire.
Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
Service
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
2.1.2 Drill/driver safety warnings
Hold power tool by insulated gripping surfaces, when performing an operation where the fastener
may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the
power tool "live" and could give the operator an electric shock.
2.1.3 Additional safety instructions
Personal safety
Tampering with or modification of the power tool is not permitted.
Wear ear protectors. Exposure to noise can cause hearing loss.
Keep the grips dry, clean and free from oil and grease.
Activate the safety lock (forward/reverse switch in the middle position) before making adjustments
to the tool, before fitting accessory tools, the side handle or depth gauge and when storing and
transporting the tool.
Do not lift or carry the tool by the accessories attached to it.
To reduce the risk of injury, use only genuine Hilti accessories and accessory tools.
Observe the national health and safety requirements.
Improve the blood circulation in your fingers by relaxing your hands and exercising your fingers
during breaks between working.
The power tool is not intended for use by inexperienced persons who have received no special
training.
Keep the power tool out of reach of children.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
4
Avoid touching rotating parts. Switch the power tool on only after bringing it into position at the
workpiece. Touching rotating parts, especially rotating tools or other accessories, may lead to injury.
Dust from material such as paint containing lead, some wood species, minerals and metal may
be harmful. Contact with or inhalation of the dust may cause allergic reactions and/or respiratory
diseases among operators or bystanders. Certain kinds of dust such as oak and beech wood dust
are classified as carcinogenic, especially in conjunction with additives for wood conditioning (chromate,
wood preservative). Material containing asbestos may be worked on only by specialists. Use a dust
removal system that is as effective as possible. To achieve a high level of dust collection, use a
suitable vacuum cleaner of the type recommended by Hilti for wood dust and/or mineral dust and
which is designed for use with this tool. Ensure that the workplace is well ventilated. Observe
national regulations applicable to the materials you intend to work with.
Electrical safety
Before beginning work, check the working area (e.g. using a metal detector) to ensure that no
concealed electric cables or gas and water pipes are present. External metal parts of the power tool
may become live, for example, when an electric cable is damaged accidentally. This presents a serious
risk of electric shock.
Work area
If the work involves breaking right through, take the appropriate safety measures at the opposite
side. Parts breaking away could fall out and / or fall down and injure other persons.
Use and care of battery-powered tools
Do not expose batteries to high temperatures, the direct heat of the sun, and keep them away
from fire. There is a risk of explosion.
Do not disassemble, crush or incinerate batteries and do not subject them to temperatures over
80°C (176°F). This presents a risk of fire, explosion or injury through contact with caustic substances.
Observe the special guidelines applicable to the transport, storage and use of lithium-ion batteries.
Never continue to use or attempt to charge damaged batteries, e.g. batteries with cracks, broken
parts, bent or pushed-in / pulled-out contacts).
Do not use the battery as a power source for other unspecified power tools or appliances.
If the battery is too hot to touch it may be defective. Allow the battery to cool in a place where there
is no risk of fire. Check that there are no flammable materials nearby. Contact Hilti Service.
3 Description
3.1 Overview of the product 1
@ Control switch
; Forward / reverse switch
= Lockbutton
% Grip
& Pressure transfer surface
( Battery interface
) Torque adjustment
+ Chuck
§ Protective cap
/ Release button with additional function
(charge status display activation)
: Depth gauge
Depth gauge adjustment
3.2 Intended use
The product described is a hand-held cordless screwdriver for fastening profile metal sheets, metal sheets
and sandwich panels in metal construction. The product is designed for driving and removing self-drilling
and self-tapping screws in appropriate materials and material thicknesses.
It is possible to use a stand-up tool for driving collated screws.
Use only Hilti Liion batteries of the B 18 series with this product.
Use only the Hilti battery chargers from the C4/36 series for these batteries.
3.3 Items supplied
Metal construction screwdriver, STDG 19 depth gauge, STDC protective cap, SNSD 8 screwdriving bit,
operating instructions.
Note
Spare parts, consumables and accessories approved by Hilti for use with the product can be found at
your local Hilti Center or online at: www.hilti.com
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
5
3.4 Liion battery display
The charge status of the Li-ion battery and malfunctions of the power tool are indicated by the display on
the Liion battery. The charge status of the Liion battery is displayed after pressing one of the two battery
release buttons.
Status Meaning
4 LEDs light. Charge status: 75 % to 100 %
3 LEDs light. Charge status: 50 % to 75 %
2 LEDs light. Charge status: 25 % to 50 %
1 LED lights. Charge status: 10 % to 25 %
1 LED blinks, the power tool is ready for use. Charge status: < 10 %
1 LED blinks, the power tool is not ready for use. The battery has overheated.
4 LEDs blink, the power tool is not ready for use. The power tool is overloaded or has overheated.
Note
Battery charge state cannot be displayed while the control switch is pressed and for up to 5 seconds
after releasing the control switch. If the battery display LEDs blink, please observe the instructions
given in the Troubleshooting section.
4 Technical data
4.1 Cordless metal screwdriver
Rated voltage
21.6 V
DC
Weight
5.5 lb
(2.5 kg)
Rated speed under no load
33.3 Hz
(2,000 rpm)
Torque
9 ftlb
f
(12 Nm)
Socket/bit drive
1
/
4
″ hex. socket with locking ring
5 Operation
Inserting the battery
WARNING
Risk of injury! Inadvertent starting of the impact screwdriver.
Before fitting the battery, check that the cordless impact screwdriver is switched off
and that the forward/reverse switch is in the middle position (i.e. safety lock engaged).
WARNING
Electrical hazards! Risk of short circuiting.
Before inserting the battery, check to ensure that the battery terminals and the contacts
in the impact screwdriver are free from foreign objects.
WARNING
Risk of injury! Hazard presented by a falling battery.
A falling battery may present a risk of injury to yourself and others. Check that the
battery is securely seated in the power tool.
Note
Make sure that the outer surfaces of the battery are clean and dry before inserting the
battery in an approved battery charger.
2
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
6
Fitting / removing the depth gauge (optional)
Note
When driving screws with a sealing washer, use a depth gauge suitable for the diameter
of the sealing washer (accessory). When the depth gauge is correctly adjusted the screw
seal will be correctly compressed.
The depth gauge is attached to the metal construction screwdriver by way of a snap-on
connection and can be simply pulled off or pushed on.
3
Setting the depth gage (accessory)
4
Using the protective cap
Note
When the depth gauge is not fitted, the guard protects the depth gauge holder from dirt
and damage.
5
Fitting / removing the accessory tool
CAUTION
Risk of injury. The accessory tool may be hot or have sharp edges.
Wear protective gloves when using the power tool and when changing accessory tools.
Note
After fitting the drill bit, grip it and pull it in order to check that it is securely engaged.
6
Fitting / removing the screw guide (optional)
Note
Use of the ‚Hilti‘ ST-SG 5.5/6.5 screw guide is recommended for sandwich panel screws.
7
Setting forward or reverse rotation
Note
An interlock prevents switching while the motor is running.
The control switch is locked when the forward/reverse switch is in the middle position
(safety lock).
8
Setting the torque
9
Safe operation
WARNING
Electric shock A fastener coming into contact with a concealed electric cable may result
in electric shock.
Never use the depth gauge or chuck as a gripping area.
Note
Always hold the tool by the grip and/or with the hands on plastic parts of the casing (in-
line grip).
10
Switching on
Note
The metal construction screwdriver must be pressed lightly against the working surface
as it will otherwise not start (for safety reasons). The running speed can be controlled
smoothly right up to maximum speed by varying how far the control switch is pressed in.
Switching on in sustained operating mode
Note
The lockbutton can be pressed in while the control switch is pressed. The metal construc-
tion screwdriver then runs in sustained operating mode. The lockbutton makes the tool
less tiring to use as the control switch does not have to be constantly pressed.
11
Switching off after sustained operation
Note
In order to be able to switch off from sustained operating mode quickly at any time, keep
your hand close to the control switch. Pressing the control switch again causes the lock-
button to jump back into its original position.
12
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
7
Removing screws
Note
Remove the depth gauge or screw guide, if fitted. Set the forward / reverse switch to the
“Reverse” position.
Removing the battery
13
6 Care of the metal construction screwdriver
WARNING
Electrical hazards! Improper repairs to electrical parts may lead to serious injuries.
Electrical parts may be repaired only by trained electrical specialists.
Keep the product, especially its grip surfaces, clean and free from oil and grease. Do not use
cleaning agents containing silicone.
Never operate the product when the air vents are blocked. Clean the air vents carefully using a dry brush.
Do not allow foreign objects to enter the interior of the product.
Clean the outside of the product at regular intervals with a slightly damp cloth. Do not use a spray, steam
pressure cleaning equipment or running water for cleaning.
Clean the connection end and the chuck at regular intervals.
6.1 Care of the lithiumion batteries
Note
Keep the battery clean and free from oil and grease.
Clean the outer surfaces with a slightly damp cloth at regular intervals. Do not use cleaning agents
containing silicone.
To achieve maximum battery life, stop drawing power from the battery as soon as a significant drop
in the performance of the power tool is noticed.
Battery discharge is stopped automatically before the battery cells suffer damage.
6.2 Transport and storage
Transport
CAUTION
Inadvertent starting during transport. Uncontrolled starting during transport may occur if the battery
is fitted, thereby resulting in damage to the tool.
Always remove the battery before transporting the tool.
Remove the battery.
Transport the tool and battery individually packaged.
Never transport batteries in bulk form (loose, unprotected).
Check tools and batteries for damage before use after long periods of transport.
Storage
CAUTION
Inadvertent damage caused by defective battery. A leaking battery may damage the tool.
Always remove the battery before storing the tool.
Store the tool and battery in a place that is as cool and dry as possible.
Never store batteries in direct sunlight, on heating units or behind a window pane.
Store the tool and batteries in a place where they cannot be accessed by children or unauthorized
persons.
Check the tool and batteries for damage before use after long periods of storage.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
8
7 Troubleshooting
If the trouble you are experiencing is not listed in this table or you are unable to remedy the problem by
yourself, please contact Hilti Service.
7.1 The metal construction screwdriver is not operational.
Trouble or fault Possible cause Action to be taken
The metal construction
screwdriver doesn’t start.
The battery is not fully inserted. Push the battery in until it
engages with an audible click.
The battery is discharged. Charge the battery.
Electrical fault. Switch the metal construction
screwdriver off immediately,
remove the battery, keep it
under observation, allow it
to cool down and contact
HiltiService.
The control switch can’t be
pressed, i.e. the switch is
locked.
The forward / reverse switch is in
the middle position.
Push the forward / reverse
switch to the left or right.
The battery is not heard to
engage.
The retaining lugs on the battery
are dirty.
Clean the retaining lugs and
push the battery in until it
engages. Contact Hilti Service
if the problem persists.
LED 1 blinks. The battery is discharged. Charge the battery.
The battery is too hot. Bring the battery to the recom-
mended operating temperature.
The battery is too cold. Bring the battery to the recom-
mended operating temperature.
The screwdriver doesn’t work
and all four LEDs blink.
The product is overloaded (appli-
cation limits exceeded).
Release the control switch and
then press it again. Reduce the
load on the tool.
7.2 The metal construction screwdriver is operational.
Trouble or fault Possible cause Action to be taken
Speed of rotation drops con-
siderably.
The battery is discharged. Charge the battery.
The metal construction
screwdriver or battery gets
very hot.
Electrical fault. Switch the metal construction
screwdriver off immediately,
remove the battery, keep it
under observation, allow it
to cool down and contact
HiltiService.
The screw is pressed too
tightly against the surface.
The depth gauge is set incorrectly. Turn the depth gauge to the
right.
The screw is not pressed
tightly enough against the
surface.
The depth gauge is set incorrectly. Turn the depth gauge to the left.
The screwdriver runs but the
screw can’t be driven.
The wrong direction of rotation is
set.
Set the forward/reverse switch
to the desired direction of
rotation.
8 Disposal
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
9
8.1 Disposal
WARNING
Risk of injury. Hazards presented by improper disposal.
Improper disposal of the equipment may have the following consequences: The burning of plastic
components generates toxic fumes which may present a health hazard. Batteries may explode
if damaged or exposed to very high temperatures, causing poisoning, burns, acid burns or
environmental pollution. Careless disposal may permit unauthorized and improper use of the
equipment. This may result in serious personal injury, injury to third parties and pollution of the
environment.
Dispose of defective batteries right away. Keep them out of reach of children. Do not disassemble
or incinerate the batteries.
Batteries that have reached the end of their life must be disposed of in accordance with national
regulations or returned to Hilti.
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The
materials must be correctly separated before they can be recycled. In many countries, your old tools,
machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative
for further information.
9 Manufacturer’s warranty
Please contact your local Hilti representative if you have questions about the warranty conditions.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
10
1 Indications relatives à la documentation
1.1 Explication des symboles
1.1.1 Avertissements
Les avertissements attirent l'attention sur des dangers liés à l'utilisation du produit. Les termes de
signalisation suivants sont utilisés en combinaison avec un symbole :
DANGER ! Pour un danger imminent qui peut entraîner de graves blessures corporelles ou la
mort.
AVERTISSEMENT ! Pour attirer l'attention sur une situation pouvant présenter des dangers
susceptibles d'entraîner des blessures corporelles graves ou la mort.
ATTENTION ! Pour attirer l'attention sur une situation pouvant présenter des dangers entraînant
des blessures corporelles légères ou des dégâts matériels.
1.1.2 Symboles
Les symboles suivants sont utilisés :
Lire le mode d'emploi avant d'utiliser l'appareil
Pour des conseils d'utilisation et autres informations utiles
Sens de rotation droite/gauche
Vitesse nominale à vide
Tours par minute
Tours par minute
1.1.3 Illustrations
Les illustrations dans le présent mode d'emploi servent à faciliter la compréhension essentielle et peuvent
différer de la version effective :
Ces chiffres renvoient à l'illustration correspondante au début du présent mode d'emploi.
La numérotation des illustrations détermine la séquence des étapes de travail dans l'image et
peut se différencier de la numérotation des étapes de travail dans le texte.
Les numéros de position sont repris dans la vue d'ensemble relative à l'illustration. Dans la sec-
tion Vue d’ensemble des produits, les numéros des légendes renvoient à ces numéros de posi-
tion.
1.2 Indications relatives à la documentation
Avant de mettre l'appareil en marche, lire impérativement ce mode d'emploi. C'est la condition
préalablement requise pour assurer la sécurité du travail et un maniement sans perturbations.
Bien respecter les consignes de sécurité et les avertissements de la présente documentation ainsi que
celles figurant sur l'appareil.
Toujours conserver le mode d'emploi à proximité de l'appareil et transmettre l'appareil à des tiers
uniquement avec ce mode d'emploi.
Sous réserve de modifications ou d'erreurs.
1.3 Informations produit
Les produits Hilti sont conçus pour les utilisateurs professionnels et ne doivent être utilisés, entretenus et
réparés que par un personnel agréé et formé à cet effet. Ce personnel doit être au courant des dangers
inhérents à l'utilisation de l'appareil. Le produit et ses accessoires peuvent s'avérer dangereux s'ils sont
utilisés de manière incorrecte par un personnel non qualifié ou de manière non conforme à l'usage prévu.
Reporter la désignation et le numéro de série qui se trouvent sur la plaque signalétique dans le tableau
suivant.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
11
Toujours fournir ces informations en cas de questions pour communiquer avec notre représentant ou
point de service :
Caractéristiques produit
Visseuse bardage ST 1800A18
Génération 01
N° de série
2 Sécurité
2.1 Consignes de sécurité
Les indications de sécurité du chapitre suivant contiennent toutes les indications générales de sécurité
pour les outils électriques qui, selon les normes applicables, doivent être spécifiées dans le présent mode
d'emploi. Par conséquent, il est possible que certaines indications ne se rapportent pas à cet appareil.
2.1.1 Indications générales de sécurité pour les outils électriques
AVERTISSEMENT Lire et comprendre toutes les consignes de sécurité et instructions. Tout
manquement à l'observation des consignes de sécurité et instructions risque de provoquer une électrocution,
un incendie et/ou de graves blessures.
Les consignes de sécurité et instructions doivent être intégralement conservées pour les utilisations
futures.
La notion d'« outil électroportatif » mentionnée dans les consignes de sécurité se rapporte à des outils
électriques raccordés au secteur (avec câble de raccordement) et à des outils électriques sur accu (sans
câble de raccordement).
Sécurité sur le lieu de travail
Conserver la zone de travail propre et bien éclairée. Un lieu de travail en désordre ou mal éclairé
augmente le risque d'accidents.
Ne pas faire fonctionner les outils électriques en atmosphère explosive et se trouvent des
liquides, des gaz ou poussières inflammables. Les outils électriques produisent des étincelles qui
peuvent enflammer les poussières ou les fumées.
Maintenir les enfants et les personnes présentes à l'écart pendant l'utilisation de l'outil électro-
portatif. En cas d'inattention il y a risque de perdre le contrôle de l'appareil.
Sécurité relative au système électrique
La fiche de secteur de l'outil électroportatif doit être adaptée à la prise de courant. Ne jamais
modifier la fiche de quelque façon que ce soit. Ne pas utiliser d'adaptateurs avec des outils
électriques à branchement de terre. Des fiches non modifiées et des prises de courant adaptées
réduiront le risque de choc électrique.
Éviter le contact physique avec des surfaces mises à la terre tels que tuyaux, radiateurs, cuisinières
et réfrigérateurs. Il y a un risque élevé de choc électrique au cas où votre corps serait relié à la terre.
Ne pas exposer les outils électroportatifs à la pluie ou à l'humidité. La pénétration d'eau à l'intérieur
d'un outil électroportatif augmentera le risque d'un choc électrique.
Ne jamais utiliser le cordon à d'autres fins que celles prévues, telles que pour porter, accrocher ou
débrancher l'outil électroportatif de la prise de courant. Maintenir le cordon à l'écart de la chaleur,
des parties grasses, des bords tranchants ou des parties de l'appareil en mouvement. Des cordons
endommagés ou emmêlés augmentent le risque de choc électrique.
Si l'outil électroportatif est utilisé à l'extérieur, utiliser uniquement une rallonge homologuée pour
les applications extérieures. L'utilisation d'une rallonge électrique homologuée pour les applications
extérieures diminue le risque d'un choc électrique.
Si l'utilisation de l'outil électrique dans un environnement humide ne peut pas être évitée, utiliser
un interrupteur de protection contre les courants de court-circuit. L'utilisation d'un tel interrupteur
de protection réduit le risque d'une décharge électrique.
Sécurité des personnes
Rester vigilant, surveiller ce que l'on fait. Faire preuve de bon sens en utilisant l'outil électroportatif.
Ne pas utiliser l'outil électroportatif si vous êtes fatigué ou sous l'emprise de l'alcool, de drogues
ou de médicaments. Un moment d'inattention lors de l'utilisation de l'outil électroportatif peut entraîner
des blessures graves.
Utiliser un équipement de sécurité et toujours porter une protection pour les yeux. Les équipements
de protection personnels tels que masque antipoussière, chaussures de sécurité antidérapantes, casque
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
12
de protection ou protection acoustique suivant l'utilisation de l'outil électroportatif, réduiront le risque de
blessures des personnes.
Éviter une mise en service par mégarde. S'assurer que l'outil électroportatif est arrêté avant de le
brancher à la source de courant et/ou à l'accu, de le prendre ou de le porter. Le fait de porter l'outil
électroportatif avec le doigt sur l'interrupteur ou de brancher l'appareil sur la source de courant lorsque
l'interrupteur est en position de fonctionnement peut entraîner des accidents.
Retirer tout outil de réglage ou toute clé avant de mettre l'outil électroportatif en fonctionnement.
Une clé ou un outil se trouvant sur une partie en rotation peut causer des blessures.
Adopter une bonne posture. Veiller à toujours garder une position stable et équilibrée. Cela permet
un meilleur contrôle de l'outil électroportatif dans des situations inattendues.
S'habiller de manière adaptée. Ne pas porter de vêtements amples ni de bijoux. Garder les
cheveux, les vêtements et les gants à distance des parties en mouvement. Des vêtements amples,
des bijoux ou des cheveux longs peuvent être happés par des parties en mouvement.
Si des dispositifs servant à aspirer ou à recueillir les poussières doivent être utilisés, s'assurer
qu'ils sont effectivement raccordés et correctement utilisés. L'utilisation d'un dispositif d'aspiration
de la poussière peut réduire les risques dus aux poussières.
Utilisation et maniement de l'outil électroportatif
Ne pas forcer l'appareil. Utiliser l'outil électroportatif adapté au travail à effectuer. Un outil
électroportatif approprié réalisera mieux le travail et de manière plus sûre au régime pour lequel il a été
conçu.
Ne pas utiliser d'outil électroportatif dont l'interrupteur est défectueux. Tout outil électroportatif qui
ne peut plus être mis en ou hors fonctionnement est dangereux et doit être réparé.
Débrancher la fiche de la prise de courant et/ou l'accu avant d'effectuer des réglages sur l'appareil,
de changer les accessoires, ou de ranger l'appareil. Cette mesure de précaution empêche une mise
en fonctionnement par mégarde de l'outil électroportatif.
Conserver les outils électroportatifs non utilisés hors de portée des enfants. Ne pas permettre
l'utilisation de l'appareil à des personnes qui ne se sont pas familiarisées avec celui-ci ou qui n'ont
pas lu ces instructions. Les outils électroportatifs sont dangereux lorsqu'ils sont entre les mains de
personnes non initiées.
Prendre soin des outils électroportatifs. Vérifier que les parties en mouvement fonctionnent
correctement et qu'elles ne sont pas coincées, et contrôler si des parties sont cassées ou
endommagées de sorte que le bon fonctionnement de l'outil électroportatif s'en trouve entravé.
Faire réparer les parties endommagées avant d'utiliser l'appareil. De nombreux accidents sont dus
à des outils électroportatifs mal entretenus.
Garder les outils de coupe affûtés et propres. Des outils destinés à couper correctement entretenus
avec des bords tranchants bien aiguisés se coincent moins souvent et peuvent être guidés plus
facilement.
L'outil électroportatif, les accessoires, les outils amovibles, etc. doivent être utilisés conformément
à ces instructions. Tenir également compte des conditions de travail et du travail à réaliser.
L'utilisation des outils électroportatifs à d'autres fins que celles prévues peut entraîner des situations
dangereuses.
Utilisation et maniement de l'outil sur accu
Ne charger les accus que dans des chargeurs recommandés par le fabricant. Si un chargeur
approprié à un type spécifique d'accus est utilisé avec des accus non recommandés pour celui-ci, il y a
risque d'incendie.
Dans les outils électroportatifs, utiliser uniquement les accus spécialement prévus pour ceux-ci.
L'utilisation de tout autre accu peut entraîner des blessures et des risques d'incendie.
Tenir l'accu non utilisé à l'écart de tous objets métalliques tels qu'agrafes, pièces de monnaie, clés,
clous, vis ou autres, étant donné qu'un pontage peut provoquer un court-circuit. Un court-circuit
entre les contacts d'accu peut provoquer des brûlures ou un incendie.
En cas d'utilisation abusive, du liquide peut sortir de l'accu. Éviter tout contact avec ce liquide. En
cas de contact par mégarde, rincer soigneusement avec de l'eau. Au cas le liquide rentrerait
dans les yeux, consulter en plus un médecin. Le liquide qui sort de l'accu peut entraîner des irritations
de la peau ou causer des brûlures.
Service
L'outil électroportatif doit uniquement être réparé par un personnel qualifié et seulement avec des
pièces de rechange d'origine. Ceci permet d'assurer la sécurité de l'appareil.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
13
2.1.2 Consignes de sécurité pour visseuse
Lors des travaux pendant lesquels la vis risque de toucher des câbles électriques cachés, tenir
l'appareil uniquement par les surfaces isolées des poignées. Le contact de la vis avec un câble
conducteur risque aussi de mettre les parties métalliques de l'appareil sous tension et de provoquer une
décharge électrique.
2.1.3 Consignes de sécurité supplémentaires
Sécurité des personnes
Toute manipulation ou modification de l'appareil est interdite.
Porter un casque antibruit. Le bruit peut entraîner des pertes auditives.
Veiller à ce que les poignées soient toujours sèches, propres et exemptes de traces de graisse et
d'huile.
Activer le blocage (inverseur du sens de rotation droite / gauche sur la position médiane) pour
entreprendre des réglages sur l'appareil, monter des outils amovibles ou une butée de profondeur,
et pour le stockage et le transport de l'appareil.
Ne pas porter l’appareil par les accessoires montés sur celui-ci.
Pour éviter tout risque de blessure, utiliser uniquement les accessoires et outils Hilti d'origine.
Observer les exigences en matière de sécurité nationales en vigueur.
Faire régulièrement des pauses et des exercices de relaxation et de massage des doigts pour
favoriser l'irrigation sanguine dans les doigts.
L'appareil n'est pas destiné à être utilisé par des personnes affaiblies sans encadrement.
L'appareil doit être tenu à l'écart des enfants.
Éviter de toucher des pièces en rotation. Brancher l'appareil uniquement dans l'espace de travail.
Le fait de toucher des pièces en rotation, en particulier des outils en rotation, risque d'entraîner des
blessures.
Les poussières de matériaux telles que des poussières de peinture au plomb, de certains types de bois,
minéraux et métaux, peuvent être nocives pour la santé. Le contact ou l'aspiration des poussières peut
provoquer des réactions allergiques et/ou des maladies respiratoires de l'utilisateur ou de toute personne
se trouvant à proximité. Certaines poussières, telles que des poussières de chêne ou de hêtre, sont
considérées comme cancérigènes, en particulier lorsqu'elles sont combinées à des additifs destinés
au traitement du bois (chromate, produit de protection du bois). Les matériaux contenant de l'amiante
doivent seulement être manipulés par un personnel spécialisé. Un dispositif d'aspiration efficace doit
être utilisé dans la mesure du possible. Utiliser un aspirateur mobile pour bois et/ou poussières
minérales recommandé par Hilti, spécialement étudié pour cet outil électroportatif. Veiller à ce que
le poste de travail soit bien ventilé. Respecter les prescriptions locales en vigueur qui s'appliquent
aux matériaux travaillés.
Sécurité relative au système électrique
Avant d'entamer le travail, vérifier, par exemple à l'aide d'un détecteur de métaux, qu'il n'y a pas
de câbles ou gaines électriques, tuyaux de gaz ou d’eau cachés dans la zone d'intervention. Toutes
pièces métalliques extérieures de l'appareil peuvent devenir conductrices, par exemple, lorsqu'un câble
électrique est endommagé par inadvertance. Cela peut entraîner un grave danger d'électrocution.
Place de travail
Lors de travaux d'ajourage, protéger l'espace du côté opposé aux travaux. Des morceaux de
matériaux risquent d'être éjectés et / ou de tomber, et de blesser d'autres personnes.
Utilisation et emploi soigneux des appareils sans fil
Ne pas exposer les accus à des températures élevées, ni au rayonnement direct du soleil ni au
feu. Il y a risque d'explosion.
Les accus ne doivent pas être démontés, écrasés, chauffés à une température supérieure à 80 °C
(176 °F) ou jetés au feu. Sinon, il y a risque d'incendie, d'explosion et de brûlure.
Respecter les directives spécifiques relatives au transport, au stockage et à l'utilisation des accus
LiIon.
Les accus endommagés (p. ex. accus fissurés, parties cassées, contacts tordus, déformés vers
l'intérieur ou l'extérieur) ne doivent plus être chargés ni utilisés.
Ne pas utiliser les accus comme source d'énergie pour d'autres appareils non spécifiés.
Si l'accu est trop chaud pour être touché, il est probablement défectueux.Laisser l'accu refroidir à
un endroit à l'abri de tout risque incendie. S'assurer qu'il n'y a aucun matériau inflammable à
proximité. Contacter le S.A.V. Hilti.
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
14
3 Description
3.1 Vue d'ensemble du produit 1
@ Variateur électronique de vitesse
; Inverseur du sens de rotation droite /
gauche
= Bouton de verrouillage
% Poignée
& Surface de transfert de la pression d'appui
( Interface d'accu
) Réglage du couple de rotation
+ Mandrin
§ Capot de protection
/ Bouton de déverrouillage avec fonction
supplémentaire d'activation de l'indicateur
de l'état de charge
: Butée de profondeur
Butée de profondeur – Réglage
3.2 Utilisation conforme à l'usage prévu
Le produit décrit est une visseuse bardage sans fil à guidage manuel servant à serrer et desserrer de la
visserie dans des profilés, des tôles et des panneaux sandwich dans des constructions métalliques. Le
produit est destiné au serrage et au desserrage de vis autoforeuses et autotaraudeuses dans des matériaux
et épaisseurs de matériau appropriés.
Il est possible d'utiliser un statif pour chargeur de vis.
Pour ce produit, utiliser exclusivement les accus LiIon Hilti de la série B 18.
Pour ces accus, utiliser exclusivement les chargeurs Hilti de la série C4/36.
3.3 Éléments livrés
Visseuse bardage, butée de profondeur STDG 19, capot de protection STDC, douille impact SNSD 8,
mode d'emploi.
Remarque
Les pièces de rechange, consommables et accessoires autorisés par Hilti convenant pour le produit
sont disponibles auprès d'un centre Hilti ou sous : www.hilti.com
3.4 Affichage de l'accu Li-Ion
L'état de charge de l'accu LiIon et les défaillances de l'appareil sont signalés sur l'écran d'affichage de
l'accu Li-Ion. L'état de charge de l'accu Li-Ion peut être visualisé en appuyant légèrement sur l'un des deux
boutons de déverrouillage.
État Signification
4 LED allumées. État de charge : 75 % à 100 %
3 LED allumées. État de charge : 50 % à 75 %
2 LED allumées. État de charge : 25 % à 50 %
1 LED allumée. État de charge : 10 % à 25 %
1 LED clignote, l'appareil est fonctionnel. État de charge : < 10 %
1 LED clignote, l'appareil n'est pas fonctionnel. Surchauffe de l'accu.
4 LED clignotent, l'appareil n'est pas fonctionnel. Charge excessive ou surchauffe de l'appareil.
Remarque
Il n'est pas possible d'interroger l'indicateur de l'état de charge lorsque le variateur électronique de
vitesse est actionné et jusqu'à 5 secondes après avoir relâché le variateur électronique de vitesse. Si
les LED de l'affichage de l'accu clignotent, se reporter au chapitre Aide au dépannage.
4 Caractéristiques techniques
4.1 Visseuse bardage
Tension de référence
21,6 V
CC
Poids
5,5 lb
(2,5 kg)
Printed: 15.10.2015 | Doc-Nr: PUB / 5070731 / 000 / 04
1 / 1