Delta 142910-SS Guide d'installation

Catégorie
Articles sanitaires
Taper
Guide d'installation
MultiChoice
®
Valve Trim
Installation Instructions
Owners Manual
13/14
Series
Write purchased model number here.
ASME A112.18.1 / CSA B125.1
ASSE 1016
®
®
U
P
C
Table of Contents:
Warranty ............................................................................. Page 2
MultiChoice
®
Rough-In Installation Instructions ...................Pages 3 - 5
13/14 Series Installation Instructions .................................. Pages 6 - 9
Maintenance ....................................................................... Page 10
Cartridge Summary References ......................................... Page 10
To order replacement parts, visit www.deltafaucet.com
1
You May Need
T
E
F
L
O
N
9/23/11
63140 Rev. B
THIS VALVE MEETS OR EXCEEDS THE
FOLLOWING STANDARDS:
ASME A112.18.1/CSA B125.1 and ASSE 1016.
CAUTION: This system/device must be set by the
installer to ensure safe, maximum temperature.
Any change in the setting may raise the discharge
temperature above the limit considered safe and
may lead to hot water burns.
NOTICE TO INSTALLER: CAUTION!–As the
installer of this valve, it is your responsibility
to properly INSTALL and ADJUST this valve
per the instructions given. This valve does
not automatically adjust for inlet temperature
changes, therefore, someone must make the
necessary Rotational Limit Stop or temperature
knob adjustments at the time of installation and
further adjustments may be necessary due to
seasonal water temperature change. YOU MUST
inform the owner/user of this requirement by
following the instructions. If you or the
owner/user are unsure how to properly make
these adjustments, please refer to page 8, and if
still uncertain, call us at 1-800-345-DELTA.
After installation and adjustment, you must affix
your name, company name and the date you
adjusted the Rotational Limit Stop or temperature
knob to the caution label provided and apply or
attach the label to the back side of the closest
cabinet door and the warning label to the water
heater. Leave this Instruction Sheet for the
owner’s/user’s reference.
WARNING: This pressure balanced or
thermostatic bath valve is designed
to minimize the effects of outlet water
temperature changes due to inlet pressure
changes, commonly caused by dishwashers,
washing machines, toilets and the like. It may
not provide protection from hot water burns
when there is a failure of other temperature
controlling devices elsewhere in the
plumbing system, if the rotational limit stop
or temperature knob is not properly set or if
the hot water temperature is changed after the
settings are made or if the water inlet changes
due to seasonal changes.
WARNING: Do not install a shut-off device on
either outlet of this valve. When this type of
device shuts off the water flow, it can defeat
the ability of the valve to balance the hot and
cold water pressures.
All parts and finishes of the Delta® faucet are
warranted to the original consumer purchaser to
be free from defects in material & workmanship
for as long as the original consumer purchaser
owns their home. Delta Faucet Company
recommends using a professional plumber for all
installation & repair.
Delta will replace, FREE OF CHARGE, during
the warranty period, any part or finish that proves
defective in material and/or workmanship under
normal installation, use & service. Replacement
parts may be obtained by calling 1-800-345-
DELTA (in the U.S. and Canada) or by writing to:
In the United States:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
In Canada:
Masco Canada Limited, Plumbing Group
350 South Edgeware Road,
St. Thomas, Ontario, Canada N5P 4L1
This warranty is extensive in that it covers
replacement of all defective parts and even
finish, but these are the only two things that
are covered. LABOR CHARGES AND/OR
DAMAGE INCURRED IN INSTALLATION,
REPAIR, OR REPLACEMENT AS WELL AS ANY
Lifetime Faucet and Finish Limited Warranty
OTHER KIND OF LOSS OR DAMAGES ARE
EXCLUDED. Proof of purchase (original sales
receipt) from the original consumer purchaser
must be made available to Delta for all warranty
claims. THIS IS THE EXCLUSIVE WARRANTY
BY DELTA FAUCET COMPANY, WHICH DOES
NOT MAKE ANY OTHER WARRANTY OF ANY
KIND, INCLUDING THE IMPLIED WARRANTY
OF MERCHANTABILITY.
This warranty excludes all industrial, commercial
& business usage, whose purchasers are
hereby extended a five year limited warranty
from the date of purchase, with all other terms of
this warranty applying except the duration of the
warranty. This warranty is applicable to Delta®
faucets manufactured after January 1, 1995.
Some states/provinces do not allow the exclusion
or limitation of incidental or consequential
damages, so the above limitation or exclusion
may not apply to you. Any damage to this faucet
as a result of misuse, abuse, or neglect, or any
use of other than genuine Delta® replacement
parts WILL VOID THE WARRANTY.
This warranty gives you specific legal rights, and
you may also have other rights which vary from
state/province to state/province. It applies only for
Delta® faucets installed in the United States of
America, Canada, and Mexico.
© 2011 Masco Corporation of Indiana
2
SHUT OFF WATER SUPPLIES.
Consider the type and thickness of your
finished wall before placing your stringer
back plate. Install the body (1) so the
surface of the finished wall is flush with the
front of the plasterguard (2) ± 3/8". Note:
For models with stops (3), plasterguard
MultiChoice
®
Rough-In Installation
1
A.
B.
Distance (1) from the stringer (2) to the
front of the plasterguard is 2.8" (71 mm).
Distance (3) from the stringer (2) to the
front of the bonnet is 3.9" (99 mm).
must be flush or subflush 3/8" to
finished wall. Mount body using the two
stringer mounting holes (4) on the bracket.
Note: Remove cover (5) to access
mounting holes. Make sure the word
“UP” (6) is on top of the valve body when
installing.
If a thin wall is used, be sure to have the
plasterguard behind the wall, otherwise
the wall should always be flush with the
front of the plasterguard. See instruction
on the bag for thin wall mounting.
1
2
6
5
4
4
1
3
2
3
3
Connect valve body to water supplies using
the proper fittings for your valve body type
(copper tubing, iron pipe or Pex). Note: (1) is
the cold inlet port and (2) is the hot inlet
port. If either of the two outlet ports is to be
unused, seal the port with a pipe plug.
C.
D.
Remove bonnet (1) and test cap (2)
before soldering. Leave screen (3)
installed. Warning: Avoid soldering at
high temperatures. Exposure to high
temperatures may damage screen. Be
sure stops (4) are removed from the w/
stops version before soldering. (Do not
install stops before soldering.)
If you are making a back to back or
reverse installation (hot on right and
cold on left) install the valve body as
described, but the water supply lines will
be reversed. Note: (1) is the hot inlet
port and (2) is the cold inlet port.
Copper Tubing Iron Pipe
Pex
1
2
1
2
1
2
1
2
3
4
MultiChoice
®
Rough-In Installation
4
Connect top outlet (1) to shower pipe with
proper fittings. Connect bottom outlet (2) to tub
spout pipe with proper fittings. Pipe (3) between
valve body and tub spout must be a minimum of
1/2" (13 mm) copper pipe or 1/2" (13 mm) iron
pipe in a straight drop no less than 8" (203 mm)
but no more than 18" (457 mm) long with only
one iron pipe or copper 90 degree elbow to the
tub spout nipple. Do not use PEX tubing for
tub spout drop.
Prior to testing, remove cover (1), bonnet
(2) and cap (3). Ensure O-ring (4) and filter
screen (5) are properly installed. Reinstall cap
and bonnet and tighten securely. Plug both
outlets with proper fittings. Check for leaks.
After testing remove shower and/or tub spout
plug and flush system. After flushing remove
filter screen (5) and reinstall cap, bonnet and
cover. Install stops (6 & 7) in the models with
stops and set to full open. Note: Install stops
as follows: Thread nut (6) onto stem (7) as
shown. Then press stem and nut assembly
into body (8) and tighten using a 3/8", 6
point, deep well socket. With a flat head
screwdriver, adjust stem clockwise to close
and counterclockwise to open.
E.
F.
MultiChoice
®
Rough-In Installation
1
2
3
PRESSURE TESTING & FLUSHING THE INSTALLATION
1
2
1
2
4
4
3
3
5
7
6
5
6
7
13 / 14 Series Installation
2
Cartridge Installation
A.
C.
Turn off water supplies. Remove
cover (1), bonnet nut (2) and test cap (3)
from the body. If this is not a thin wall
mounting, the entire plasterguard (4)
may be removed. If screen (5) is in place,
remove before installing cartridge.
For back to back or reverse installations
(hot on right and cold on left) insert the
cartridge with the “hot side” on the right.
If you are not making a reverse or back
to back installation skip this step and
continue with step 1C.
Slide bonnet nut (1) over the cartridge
and thread onto the body. Hand tighten
securely.
B.
Rotate the cartridge (1) so the words
“hot side” (2) appear on the left. Insert
cartridge into valve body as shown. Make
sure the cartridge tubes and O-rings (3)
are properly seated in holes at the base of
the body. Ensure the keys on the body are
fully engaged with the slots in the body (4).
Back to back Installation
Normal Installation (changes not required)
Reverse
Installation
Cold
Hot
1
2
3
1
4
4
2
3
1
6
5
4
13 / 14 Series Installation
3
Showerhead and Tub Spout Installation
FOR SHOWERHEAD INSTALLATION:
Connect top outlet (1) to shower arm (2)
with proper fittings. To prevent damage
to finish on shower arm, insert wall end
of shower arm into shower flange (3)
before screwing arm into riser connection.
Thread showerhead (4) onto shower
arm. Apply plumber tape to pipe threads
on both ends. Do not overtighten
showerhead.
A.
3
2
1
Slip-On Installation
The copper tube (1) must be 1/2” nominal
copper. Important: If it is necessary to cut
the copper tube, the end must be cham-
fered free of burrs to prevent cutting or
nicking O-ring inside the spout. Slide spout
over copper tube flush with the finished tub
or wall surface. Tighten set screw (2), but
do not overtighten.
4
1
7
FOR TUB SPOUT INSTALLATION:
Refer to the installation instructions supplied with your spout. Do not connect deck mount
spouts to in-wall valves. Do not use hand showers connected in lieu of a tub spout to a
tub/shower valve. Do not use PEX tubing for tub spout drop.
B-1
B-2
B-3
Iron Pipe Installation
Install threaded pipe nipple (1) to extend
past finished wall. Apply plumber tape to
threads on pipe nipple and screw on
tub spout.
Copper Sweat Installation
Remove O-ring (1) from adapter (2). Solder
adapter to tube taking care to keep solder
away from O-ring groove. CAUTION: NO
SOLDER PERMITTED ON OUTSIDE
DIAMETER OF ADAPTER ADJACENT
TO O-RING GROOVE. Cut off tube (3) and
replace O-ring on groove of brass adapter.
Thread tub/spout onto adapter, taking care
not to damage O-ring, and hand tighten until
spout is firmly against finished wall and all
slack is taken up behind wall.
2
1
1
2
3
13 / 14 Series Installation
8
13 / 14 Series Installation
4
Adjusting the Rotational Limit Stop
IMPORTANT:
The Rotational Limit Stop is used to limit the
amount of hot water available such that, if set
properly, the user will not be scalded if the han-
dle accidentally is rotated all the way to “hot”
when a person is showering or filling a tub. The
first position allows the LEAST amount of hot
water to mix with the cold water in the system.
In the first position the water will be the coldest
possible when the handle is turned all the way
to hot. As you move the Rotational Limit Stop
counterclockwise, you progressively add more
and more hot water in the mix. The last position
to the left will result in the greatest amount of
hot water to the mix, and the greatest risk of
scald injury if someone accidentally turns the
valve handle all the way to the hot side while
showering or filling a tub.
WARNING: In some instances, setting the
Rotational Limit Stop in the hottest position
(full counterclockwise) could result in scald
injury. It is necessary to adjust the Rotation-
al Limit Stop so that the water coming out
of the valve will not scald the user when the
handle of the valve is rotated to the hot side.
• According to the majority of industry stan-
dards, the maximum allowable temperature of
the water exiting the valve is 120°F (Your local
plumbing codes may require a water tempera-
ture less than 120°F).
The Rotational Limit Stop may need to be re-
adjusted seasonally if the inlet water tempera-
ture changes. For example, during the winter,
the cold water temperature is colder than it is
during the summer which could result in vary-
ing outlet temperatures. A water temperature
for a comfortable bath or shower is typically
between 90°F - 110°F.
• Run the water so that the cold water is as
cold as it will get and hot water is as hot as
it will get. Place the handle on the stem (see
page 9, step 5D) and rotate the handle coun-
terclockwise until the handle stops.
• Place a thermometer in a plastic tumbler
and hold in the water stream. If the water
temperature is above 120°F, the Rotational
Limit Stop must be repositioned clockwise to
decrease valve outlet water temperature to
be less than 120°F or to meet the require-
ments of your local plumbing codes.
To adjust the temperature of the water
coming out of the valve, pull the disc back to
a position where it is possible to remove the
Rotational Limit Stop and readjust the teeth
engagement position to the desired tem-
perature. Clockwise will decrease the outlet
temperature, counterclockwise will increase
the outlet temperature. Temperature change
per tooth (notch) could be 4° - 16°F based on
inlet water conditions. Repeat as necessary.
Push disc until fully seated.
WARNING: Failure to re-install Disc after
setting Rotational Limit Stop could result
in scald injury.
• MAKE SURE COLD WATER FLOWS
FROM THE VALVE FIRST. MAKE SURE
WATER FLOWING FROM THE VALVE
AT THE HOTTEST FLOW POSSIBLE
DOES NOT EXCEED 120°F OR THE
MAXIMUM ALLOWED BY YOUR LOCAL
PLUMBING CODE.
1st Position
Hotter
Rotational Limit Stop
Stem
Disc
13 / 14 Series Installation
5
Trim Installation
C.
D.
A.
B.
Slide O-ring (1) over cartridge and the
bonnet nut (2). The O-ring, which acts as
a spacer to steady the sleeve, should rest
behind the bonnet nut.
If your model requires a spacer (1), insert
it into the sleeve (2) and push it to the
front. Slide the sleeve over the cartridge,
body and O-ring.
Secure the escutcheon (1) and backplate
(2) (if your model has one) to the bracket
(3) using the 2 screws provided (4). Do not
overtighten escutcheon screws.
Using an Allen wrench to secure the set
screw, install the handle onto the stem.
1
2
1
2
1
1
2
3
4
9
Faucet leaks from tub spout/showerhead:
SHUT OFF WATER SUPPLIES.
Replace seats and springs–Repair
Kit RP4993. Check condition of lower O-rings and
replace if necessary RP14414. See Helpful Hints 1,
2, & 3.
If leak persists:
SHUT OFF WATER SUPPLIES.
Replace cap assembly RP46070 or valve cartridge
RP46074.
See Helpful Hints 1, 2, 3 & 5.
Unable to maintain constant
water temperature:
Replace housing assembly with RP46071 or follow
instructions in Helpful Hints 1, 2, 4 & 5.
Helpful Hints:
1. Before removing valve cartridge assembly for any
maintenance, be sure to note the position of the
rotational limit stop on the cap. The valve cartridge
assembly must always be put back in the same
position. BE SAFE! After you have finished the
installation, turn on valve to make sure COLD
WATER FLOWS FIRST.
2. To remove valve cartridge from body, shut off
water supplies and remove handle and bonnet
nut. Do not pry the valve cartridge out of the body
with a screwdriver. Place handle on stem and rotate
counterclockwise approximately 1/4 turn after the
stop has been contacted. Lift valve cartridge out
of body.
3. To remove seats and springs, remove valve
cartridge. Separate cap assembly from the
housing assembly by rotating the cap assembly
counterclockwise 90
o
(degrees). Separate cap
and housing assemblies. Remove seats and
springs and replace. Place the largest diameter
of the spring into the seat pocket first and then
press the tapered end of the seal over the spring.
Reassemble valve cartridge and replace in body
following instructions given in 1 above.
4. If the water in your area has lime, rust, sand
or other contaminants in it, your pressure
balance valve will require periodic inspection.
The frequency of the inspection will depend
on the amount of contaminants in the water. To
inspect valve cartridge remove it and follow the
steps in note 1 above. Turn the valve to the full
mix position and shake the cartridge vigorously.
If there is a rattling sound, the unit is functional
and can be reinstalled following instructions given
in note 1 above. If there is no rattle, replace the
housing assembly (RP46071).
5. Push disc until fully seated. See page 8 for
more details.
To order replacement parts, visit
www.deltafaucet.com
13/14 Series Maintenance
10
Cleaning and Care
Care should be given to the cleaning of this prod-
uct. Although its finish is extremely durable, it can
be damaged by harsh abrasives or polish. To clean,
simply wipe gently with a damp cloth and blot dry
with a soft towel.
Warning: Scrubbing Bubbles
®
Bathroom Cleaner
and Lysol
®
Basin Tub and Tile Cleaner must not be
used on the clear knob handles and levers. Use of
these cleaners can result in cracked or severely
damaged handles. If overspray gets onto the
handles, immediately wipe them dry with a soft
cotton cloth
MultiChoice
®
13/14
Grey
Off White
Longer
Lower Housing
Order RP46074 to
Replace Cartridge.
Old
Monitor
®
1300/1400
White
Blue
or
Off White
Shorter Lower Housing
Order RP19804 to
Replace Cartridge.
White
Blue
Shorter Lower Housing
Order RP19804 to
Replace Cartridge.
New
Monitor
®
1300/1400
Cartridge Summary Reference
Units shipped in March
2006 and after.
Replacement cartridges
shipped in July 2006
and after.
Units shipped before
March 2006.
Instrucciones para la
Instalación del Accesorio
para Válvulas MultiChoice
®
Manual para los
Propietarios
13 y 14
Series
Escriba aquí el número del modelo comprado.
ASME A112.18.1 / CSA B125.1
ASSE 1016
®
®
U
P
C
ESTA VÁLVULA CUMPLE O EXCEDE LAS
SIGUIENTES NORMAS:
ASME A112.18 1 / CSA B125.1 y ASSE 1016.
ADVERTENCIA: El instalador debe apostar
este systema/divisa para garantizar temperatura
maximo y seguro. Cualqueir cambio en el ajuste
puede subir la temperatura del agua de descarga
sobre el límite considerado seguro y puede
resultar en quemaduras de agua caliente.
AVISO PARA EL INSTALADOR: PRECAUCIÓN
– Como instalador de esta válvula, es su
responsabilidad de INSTALAR Y AJUSTAR
apropiadamente esta válvula como se describe
en las instrucciones, por lo tanto, debe haber
una persona para hacer los ajustes necesarios
del Tope del Límite Rotacional y del pomo
para la temperatura en el momento que se
haga la instalación y pueda necesitar ajustes
adicionales por los cambios estacionales
de la temperatura del agua. USTED DEBE
informarle al dueño/usuario sobre este
requisito siguiendo las instrucciones. Si usted
o el dueño/usuario no están seguros como
hacer estos ajustes apropiadamente, por favor
refiérase al Página 8 y si todavía no está seguro,
llámenos al 1-800-345-DELTA.
Después de hacer la instalación y el ajuste,
usted puede agregarle a la etiqueta de aviso
proporcionada, su nombre, el nombre de la
compañía y la fecha cuando ajustó el Tope del
Límite Rotacional y el pomo para la temperatura y
aplicar o fijar la etiqueta al dorso de la puerta del
gabinete más cercano y la etiqueta de aviso al
calentador de agua. Deje la Hoja de Instrucciones
para referencia del dueño/usuario.
ADVERTENCIA: Esta válvula de presión
balanceada y termostática está diseñada
para minimizar los efectos de los cambios
de temperatura de agua por causa de los
cambios de presión en el agua de entrada,
comúnmente causados por lavadoras de
platos, lavadoras de ropa, inodoros, y otros
aparatos por el estilo. Puede no proporcionar
protección de quemaduras de agua caliente
cuando hay alguna falla de otros aparatos
para el control de temperatura en otro
sitio en el sistema de plomería. También
no proporcionará protección si el tope del
límite rotacional y el pomo para el ajuste de
la temperatura no está apropiadamente fijo
o si cambia la temperatura del agua caliente
después de hacer los ajustes o si los cambios
del agua de entrada son por los cambios
estacionales.
ADVERTENCIA: No instale un aparato de corte
o cierre en cualquiera de las tomas de esta
válvula. Cuando este tipo de aparato cierra el
flujo de agua, puede hacer fallar la habilidad
de la válvula de balancear las presiones del
agua caliente y fría.
Contenido:
Garantías ........................................................................... Página 2
La instalación de la plomería MultiChoice
®
......................... Páginas 3 - 5
Instrucciones de Instalación para la Series 13 / 14............. Páginas 6 - 9
Mantenimiento .................................................................... Página 10
Hoja resumen de referencia para el cartucho .................... Página 10
Para ordenar las piezas de repuesto, visítenos en www.deltafaucet.com
1
Usted puede necesitar
9/23/1163140 Rev. B
T
E
F
L
O
N
Todas las piezas y acabados de la llave Delta
®
están garantizados al consumidor comprador
original, de estar libres de defectos de material
y fabricación, por el tiempo que el consumidor
comprador original sea dueño de su casa. Delta
Faucet Company recomienda que use un
plomero profesional para todas las instalaciones
y zreparaciones.
Delta reemplazará, LIBRE DE CARGO, durante
el período de garantía, cualquier pieza o
acabado que pruebe tener defectos de material
y/o fabricación bajo instalación normal, uso y
servicio. Piezas de repuesto pueden ser
obtenidas llamando al 1-800-345-DELTA (en los
Estados Unidos y Canada) o escribiendo a:
En los Estados Unidos:
Delta Faucet Company
Product Service
55 E. 111th Street
Indianapolis, IN 46280
En Canada:
Masco Canada Limited, Plumbing Group
350 South Edgeware Road,
St. Thomas, Ontario, Canada N5P 4L1
Esta garantía es extensiva en lo que cubre el
reemplazamiento de todas las piezas
defectuosas y hasta el acabado, pero éstas
son las únicas dos cosas que están cubiertas.
CARGOS DE LABOR Y/O DAÑOS INCURRIDOS
EN LA INSTALACIÓN, REPARACIÓN, O
REEMPLAZAMIENTO COMO TAMBIÉN
Garantía Limitada De Por Vida de la Llave y su Acabado
CUALQUIER OTRO TIPO DE PÉRDIDA O
DAÑOS ESTÁN EXCLUÍDOS. Prueba de
compra (recibo original de venta) del comprador
consumidor original debe de ser disponible a
Delta para todos los reclamos. ESTA ES LA
GARANTÍA EXCLUSIVA DE DELTA FAUCET
COMPANY, QUE NO HACE CUALQUIER
OTRA GARANTÍA DE CUALQUIER TIPO,
INCLUYENDO LA GARANTÍA IMPLÍCITA DE
COMERCIALIZACIÓN.
Esta garantía excluye todo uso industrial,
comercial y de negocio, a cuyos compradores
se les da una garantía limitada extendida de
cinco años desde la fecha de compra, con todos
los otros términos de esta garantía aplicados,
excepto el de duración de ésta. Esta garantía
es aplicable a las llaves de Delta
®
fabricadas
después de Enero 1, 1995.
Algunos estados/provincias no permiten la
exclusión o limitación de daños incidentales o
consecuentes, de manera que la limitación o
exclusión arriba escrita puede no aplicarle a
usted. Cualquier daño a esta llave, resultado del
mal uso, abuso, o descuido, o cualquier otro uso
de piezas de repuesto que no sean genuinas de
Delta
®
ANULARÁN LA GARANTÍA.
Esta garantía le da derechos legales específicos,
y usted puede, también tener otros derechos que
varían de estado/provincia a estado/provincia.
Es aplicable sólo a las llaves Delta
®
instaladas
en los Estados Unidos de America, Canada
y Mexico.
© 2011 Masco Corporación de Indiana
2
CIERRE LOS SUMINISTROS DE AGUA.
Considere el tipo y el grosor de su pared
terminada antes de colocar su placa trasera
de acoplamiento de las tuberías. Instale la
pieza (1) de manera que la superficie de la
pared terminada quede al ras con el frente
del protector de yeso (2) ± 3/8". Nota: Para
con los modelos de las paradas (3), el
protector del yeso debe ser el rubor
Instalación de la plomería MultiChoice
®
1
A.
B.
La distancia (1) del empalme de tuberías
(2) al frente del protector de yeso es 2.8"
(71 mm). La distancia (3) del empalme de
tuberías (2) al frente de la tuerca tapa o
capuchón es 3.9" (99 mm).
rasante o secundario el 3/8a la pared
acabada. Instale la pieza usando los dos
agujeros de instalación del acoplamiento
(4) en el soporte. Nota: Quite la cubierta
(5) para tener acceso a los agujeros
de instalación. Cuando esté haciendo la
instalación, asegúrese que la palabra
“UP” (6) quede arriba de la válvula.
Si usted está trabajando en una pared
delgada, asegúrese de tener un protector
de yeso detrás de la pared, si no la pared
siempre deberá estar al ras con el frente
del protector de yeso.
1
2
6
5
4
4
1
3
2
3
3
Conecte el cuerpo de la válvula a los sumin-
istros de agua usando los accesorios apro-
piados para el tipo de su válvula (tubería de
cobre, hierro o Pex). Nota: (1) es la entrada
del agua fría y el (2) es la entrada del agua
caliente. Si no va a usar alguna de las dos
entradas de agua, séllela con un tapón
de tubería.
C.
D.
Quite la tuerca tapa (1) y la tapa de prueba
(2) antes de soldar. Deje la rejilla (3) instalada.
AVISO: Evite soldar a temperaturas altas.
Si se deja expuesto a temperaturas altas
pudiera dañar la rejilla. Sea seguro que las
válvulas apagadas (4) están quitadas
de la versión con las paradas antes de
soldar. (no instale las válvulas apagadas
antes de soldar.)
Si está hacienda una instalación dorso
con dorso o a la inversa (caliente en la
derecha y fría en la izquierda) instale el
cuerpo de la válvula como se describe
arriba, pero coloque al inverso las líneas
de suministro de agua. Nota: (1) es
la entrada de agua caliente (2) es la
entrada del agua fría.
Tubería de
Cobre
Hierro
Pex
1
2
1
2
1
2
1
2
3
4
Instalación de la plomería MultiChoice
®
4
Conecte la salida de arriba (1) a la tubería de
la regadera con los accesorios apropiados.
Conecte la salida de abajo (2) a la tubería
del surtidor de la bañera con los accesorios
apropiados. La tubería (3) entre el cuerpo de
la válvula y el de la bañera debe ser de un
mínimo de 1/2" (13 mm) de tubería de cobre
ó 1/2" (13 mm) de tubería de hierro en caída
recta no menos de 8" (203 mm) pero no más
de 18" (457 mm) de largo a la entrerrosca del
surtidor de la bañera y con sólo un codo de 90
grados, de tubería de hierro o cobre. No use la
tubería PEX como tubería entre la válvula y
el surtidor de la bañera.
Antes de probar, quite la cubierta (1), el capuchón
(2) y la tapa (3). Asegúrese que el aro O (4) y el filtro
de malla (5) están correctamente instalados. Si lo
ha quitado, instale otra vez la tapa y el capuchón, y
apriete bien. Tape ambas salidas con los accesorios
apropiados. Examine si hay filtraciones o fugas.
Después de hacer la prueba quite el tapón de la
regadera y/o bañera y deje que el agua corra para
limpiar el sistema de tuberías. Después de dejar el
agua correr quite el filtro de malla (5) y reinstale la tapa,
el capuchón y la cubierta. Instale las válvulas apagadas
(6 y 7) en con las paradas versión y sistema para
abrirse por completo. Nota: Instale las paradas
en con la versión de las válvulas apagadas
como sigue: Rosque la tuerca (6) en el vástago
(7) según lo demostrado. Después presione
el montaje del vástago y de tuerca en cuerpo
(8) y apriete con un 3/8", 6 puntos, zócalo bien
profundo. Con un destornillador principal
plano, ajuste el vástago a la derecha al cierre y
a la izquierda abrirse.
E.
F.
Instalación de la plomería MultiChoice
®
1
2
3
PRUEBA DE PRESIÓN Y LIMPIEZA DE LA INSTALACIÓN
1
2
1
2
4
4
3
3
5
7
6
5
6
7
Instalación de las Series 13 / 14
1
Instalación del Cartucho
A.
C.
Cierre los suministros de agua. Quite la
cubierta (1), la tuerca tapa (2) y la tapa de
prueba (3). Si no es para instalar en pared
delgada, puede quitar el protector (4) de
yeso completo. Si la pantalla (5) está en lugar,
quite antes de instalar el cartucho.
En las instalaciones dorso con dorso o al
reverso (caliente en la derecha y fría en la
izquierda) introduzca el cartucho con la in-
scripción “hot side” a la derecha. Si usted no
está instalando al reverso o dorso con dorso
omita este paso y continúe con el paso 1C.
Deslice la tuerca tapa (1) sobre el cartucho
y enrosque en el cuerpo de la válvula.
Apriete a mano bien. .
B.
Gire el cartucho (1) de manera que las palabras
‘hot side’ (lado caliente) (2) aparezcan a la izqui-
erda. Introduzca el cartucho en la válvula como se
muestra. Asegúrese que los tubos del cartucho y
los aros-O (3) estén apropiadamente sentados en
los agujeros en la base del cuerpo de la válvula.
Asegúrese que la parte dentada en el cuerpo de
la pieza encaje completamente en las muescas
de éste (4).
Instalación de Espalda a Espalda
Instalación Normal (No serequerá cambios)
Instalación
Invertido
Fría
Caliente
1
2
3
1
4
4
2
3
1
6
5
4
PARA LAS INSTALACIONES DE LAS
CABEZAS DE REGADERA: Conecte
la toma de salida de agua superior (1) al
brazo de la regadera (2) con los accesorios
apropiados. Para prevenir daño al acabado
del brazo de la regadera, introduzca el
extremo que va hacia la pared del brazo
de la regadera dentro del reborde (3) antes
de atornillar el brazo en la conexión de la
tubería vertical. Aplique cinta para plomero
los enrosques de la tubería. No apriete
demasiado la cabeza de la regadera (4).
A.
3
2
1
Instalación de las Series 13 / 14
2
Instalación de la Cabeza de la Regadera y el Surtidor de la Bañera
7
Instalación deslizable
El tubo de cobre (1) debe ser de1/2" de cobre
nominal. Importante: Si es necesario cortar el
tubo de cobre, el extremo debe biselarse que
quede libre de rebabas para prevenir cortar
o mellar el aro O dentro del tubo de cobre.
Deslice el surtidor sobre el tubo de cobre al
ras con la bañera o la superficie de la pared
acabada. Apriete el tornillo de ajuste (2), pero
no apriete demasiado.
1
PARA LA INSTALACIÓN DEL SURTIDOR DE LA BAÑERA: Refiérase a las instrucciones
para la instalación suministradas con su surtidor. No conecte los surtidores para las instalacio-
nes en las superficies horizontales en las válvulas dentro de las paredes. No use las regaderas
de mano en vez de un surtidor de bañera conectado a una válvula de bañera/regadera. No use
la tubería PEX como tubería entre la válvula y el surtidor de la bañera.
B-1
B-2
B-3
Instalación de la tubería de Hierro
IInstale una entrerrosca de tubo enroscado
de 1/2” (13 mm) (1) para extenderse por
delante de la pared acabada. Aplique cinta
para plomero las roscas en la entrerrosca de
tubo y atornille el surtidor de la bañera.
Instalación de Soldadura de Cobre
Quite el aro O (1) del adaptador (2). Suelde el
adaptador al tubo asegurando de mantener
la soldadura lejos de las muesca del aro O.
AVISO: NO SE PERMITE SOLDAR EN EL
DIAMETRO EXTERIOR DEL ADAPTADOR
ADJUNTO A LA MUESCA DEL ARO O. Corte
el tubo (3) y coloque otra vez el aro O en la
muesca del adaptador de latón. Atornille la
bañera/surtidor al adaptador, asegurando no
dañar el aro O, y apriete a mano bien hasta que
el surtidor quede firmemente contra la pared
acabada y no quede flojo detrás de la pared.
2
1
1
2
3
4
8
Instalación de las Series 13 / 14
3
El Ajuste del Tope que Limita la Rotación
IMPORTANTE:
El Ajuste del Tope que Limita la Rotación
se usa para limitar la cantidad de agua
caliente disponible de manera que, si
ajustado apropiadamente, el usuario no se
quemará si la manija se gira accidentalmente
completamente a “hot” (“caliente”) cuando
una persona se está duchando o llenando
la bañera. La primera posición permite la
cantidad MÍNIMA de agua caliente mixta con
la fría en el sistema. En la primera posición
el agua estará lo más fría posible cuando
la manija se gira completamente a caliente.
Mientras que mueve el Ajuste del Tope que
Limita la Rotación en dirección contrario a
las manecillas del reloj, progresivamente
aumentará el agua caliente en la mezcla
más y más. La última posición a la izquierda
es la de mayor cantidad de agua caliente en
la mezcla, y tiene el mayor riesgo de lesión
por quemadura si alguien accidentalmente
abre la manija de la válvula completamente
a la posición caliente mientras que se baña o
llena la bañera.
ADVERTENCIA: En algunos casos,
ajustar el Ajuste del Tope que Limita la
Rotación en la posición más caliente
(completamente en el sentido contrario
a la dirección de las manecillas del reloj)
puede resultar en lesión por quemadura.
Es necesario ajustar el Tope que Limita
la Rotación de manera que el agua que
sale de la válvula no queme o escalde al
usuario cuando la manija de la válvula se
gira al lado caliente.
De acuerdo con la mayoría de los estándares
de la industria, la temperatura máxima
permisible del agua que sale es 120°F (Sus
códigos locales de plomería pueden requerir
una temperatura de agua menor de 120°F).
El Tope que Limita la Rotación puede
requerir el ajuste estacional si la temperatura
del agua cambia. Por ejemplo, durante el
invierno, la temperatura del agua fría es más
fría que durante el verano resultando en tem-
peraturas variadas en el agua de salida. Una
temperatura de agua para un baño o ducha
confortable típicamente es entre 90°F - 110°F.
Deje que el agua corra de manera que el agua
fría esté lo más fría posible y la caliente esté
lo más caliente posible. Coloque la manija en
la espiga (vea la página 9, paso 5D) y gire la
manija en dirección contraria a las manecillas
del reloj hasta que la manija pare.
Coloque el termómetro en un vaso plástico y
sosténgalo bajo el chorro de agua. Si la tem-
peratura de agua está por encima de 120°F el
tope que limita la rotación debe ajustarse otra
vez moviéndolo en sentido de las manecillas
del reloj para reducir la temperatura del agua
de salida de la válvula a menos de 120°F o
para que cumpla con los requisitos de sus
códigos locales de plomería.
Para ajustar la temperatura del agua que
sale de la válvula, hale el disco otra vez a la
posición donde se puede remover el Tope
del Límite Rotacional y reajuste el engranaje
de los dientes a la posición para la tempera-
tura deseada. Al mover en dirección de las
manecillas del reloj reducirá la temperatura
del agua de salida, y al contrario aumentará la
temperatura del agua de salida. El cambio de
temperatura por cada diente (muesca) puede
ser de 4°F-16°F dependiendo de la condición
del agua de entrada. Si es necesario repítalo.
Presione el disco hasta que está asentado
completamente. ADVERTENCIA: Si no rein-
stala el Disco después de hacer el ajuste
del Tope del Límite Rotacional pudiera
escaldarse con agua demasiado caliente.
ASEGÚRESE QUE EL AGUA FRÍA FLUYA DE
LA VÁLVULA PRIMERO. ASEGÚRESE QUE
EL AGUA QUE FLUYE DE LA VÁLVULA EN LA
POSICIÓN MÁS CALIENTE POSIBLE NO EX-
CEDA 120°F O EL MÁXIMO PERMITIDO POR
SUS CÓDIGOS LOCALES DE PLOMERÍA.
Posición Primera
Más
Caliente
Unidad
del Vástago
Tope de Limite de Girar
Disco
Instalación de las Series 13 / 14
4
Instalación Final
C.
D.
A.
B.
Deslice el aro O (1) sobre el cartucho y la
tuerca tapa (2). El aro O, el cual funciona
como un separador para estabilizar la manga,
debe quedar apoyado en la tuerca tapa.
Si su modelo requiere un separador (1),
insértelo en la manga (2) y empújelo hacia el
frente. Deslice la manga sobre el cartucho,
el cuerpo de la pieza y el aro O.
Fije la roseta con orificio (1) y la placa de
atrás (2) (si su modelo tiene una) al soporte
(3) usando los 2 tornillos suministrados (4).
No apriete demasiado los tornillos de la
roseta.
Instale la manija en la espiga, usando una
llave Allen para fijar el tornillo de ajuste.
1
2
1
2
1
1
2
3
4
9
Tenga cuidado al ir a limpiar este producto.
Aunque su acabado es sumamente durable,
puede ser afectado por agentes de limpieza o
para pulir abrasivos. Para limpiar su llave, sim-
plemente frótela con un trapo húmedo y luego
séquela con una toalla suave.
Limpieza y Cuidado de su Llave
¡ADVERTENCIA! No se puede usar
SCRUBBING BUBBLES® BATHROOM
CLEANER o LYSOL® BASIN TUB AND TILE
CLEANER en las manijas transparentes. El uso
de estos productos pueden resultar en manijas
rajados o severamente dañados. Si estos produc-
tos caen sobre la manija, séquelo inmediata-
mente con una toalla de algodón suave.
La llave tiene fugas de agua en la
salida de tina/cabeza deregadera–
CIERRE LOS SUMINISTROS DE AGUA.
Reemplace Asientos y Resortes–Equipo de
Reparaciones RP4993 Verifica el condición de los
anillos “O” más bajo y repongalos si será necesario
RP14414. Vea Sugerencias Utiles 1, 2, y 3.
Si la fuga de agua persiste–
CIERRE LOS SUMINISTROS DE AGUA.
Reemplace el ensamble de Tapón Equipo de
Reparaciones RP46070 o cartucho de válvula
RP46074. Vea Sugerencia Utiles 1, 2, 3 y 5.
No se puede mantener temperatura de
agua constante:
Reemplace ensamble de caja con RP46071 o sigue
los instrucciones en Sugerencias Utiles 1, 2, 4 y 5.
Sugerencia Utiles:
1. Antes de remover el ensamble del cartucho de
la válvula para hacerle cualquier servicio, fíjese en
la posición del tope del límite rotacional ubicado en
la tapa. Siempre se debe reponer el ensamble de
cartucho de válvula en el mismo posición. TENGA
CUIDADO después de cumplir el instalación dele
vuelta a la válvula para asegurar que AGUA FRIA
SALGA PRIMERO.
2. Para quitar el cartucho de válvula del cuerpo, cierre
los suministros de agua y quite el maneral y bonete.
No se debe quitar el cartucho de válvula del cuerpo
con atornillador. Ponga el maneral encima el vástago y
giralo en el sentido contrario al de las agujas del reloj
aproximado 1/4 vuelta. Levanta el cartucho de válvula
aguera el cuerpo.
3. Para quitar los asientos y resortes, quite el
cartucho de válvula, (vea arriba). Separa ensamble
de botón de ensamble de caja girando el botón
90o en el sentido contrario al de las agujas del
reloj. Separa ensambles de botón y caja. Quite los
asientos y resortes y ponga los asientos y resortes
nuevos. Ponga primero el diámetro mas grande del
resorte adentro la bolsa del asiento y luego apreta
el remate ahusado del sello hacia arriba el resorte.
Reensembla el cartucho de válvula y repongalo en el
cuerpo siguendo los instrucciones en nota 1 arriba.
4. Si la agua en su area contiene cal, orín, arena
o otros contaminamientos, su válvula de equilibrio
de presión requerá inspecciones periódico. La
frequencía de los inspecciones depende en el
tamaño de contaminamientos en la agua. Para
inspectar el cartucho, quite el cartucho, sigue los
pasos apuntado en nota 1 arriba. Dele vuelta al
válvula hasta el posición completamente mixto
y sacude el cartucho riguroso. Si hay traqueteo,
funciona el unidad y se puede reinstalar siguendo
nota 1 de arriba. Si no hay traqueteo, reemplace el
ensamble de caja (RP46071).
5. Presione el disco hasta que está asentado
completamente. Vea la página 8 para más detalles.
Para ordenar las piezas de repuesto, visítenos
en www.deltafaucet.com
Mantenimiento de las Series 13 / 14
10
MultiChoice
®
13/14
Gris
Blancuzco
Bastidor más Largo
Ubicado más Abajo
Ordene el Repuesto RP46074
para cambiar el cartucho.
Viejo
Monitor
®
1300/1400
Blanco
Azul o
Blancuzco
Más corto Más abajo Bastidor
Ordene el Repuesto RP19804
para cambiar el cartucho.
Blanco
Azul
Nuevo
Monitor
®
1300/1400
Hoja resumen de referencia para el cartucho
Unidades enviadas en
Marcha de 2006 y después.
Los cartuchos del reem-
plazo enviaron en julio de
2006 y después.
Unidades enviadas antes de
Marcha de 2006.
Ordene el Repuesto RP19804
para cambiar el cartucho.
Más corto Más abajo Bastidor
1 / 1

Delta 142910-SS Guide d'installation

Catégorie
Articles sanitaires
Taper
Guide d'installation