Dometic CDF18, CDF26, CDF36, CDF46 Mode d'emploi

CDF18, CDF26, CDF36, CDF46

Compressor Cooler

Operating manual . . . . . . . . . . . . . . . . . . . . . 4

Kompressor-Kühlbox

Bedienungsanleitung . . . . . . . . . . . . . . . . .22

Glacière à compression

Notice d’utilisation . . . . . . . . . . . . . . . . . . . 41

Nevera por compresor

Instrucciones de uso . . . . . . . . . . . . . . . . . . 61

Geleira com compressor

Manual de instruções . . . . . . . . . . . . . . . . .80

Frigorifero a compressore

Istruzioni per l’uso . . . . . . . . . . . . . . . . . . .100

Compressorkoelbox

Gebruiksaanwijzing. . . . . . . . . . . . . . . . . .120

Kompressor-køleboks

Betjeningsvejledning . . . . . . . . . . . . . . . .139

Kylbox med kompressor

Bruksanvisning. . . . . . . . . . . . . . . . . . . . . . 157

Kjøleboks med kompressor

Bruksanvisning. . . . . . . . . . . . . . . . . . . . . . 175

Kompressori-kylmälaatikko

Käyttöohje . . . . . . . . . . . . . . . . . . . . . . . . .193

Компрессорный холодильник

Инструкция по эксплуатации . . . . . . . . . 211

Lodówka kompresorowa

Instrukcja obsługi . . . . . . . . . . . . . . . . . . . 231

Chladiaci box s kompresorom

Návod na obsluhu. . . . . . . . . . . . . . . . . . . 250

Kompresorový chladicí box

Návod k obsluze . . . . . . . . . . . . . . . . . . . .268

Kompresszor hűtőláda

Használati utasítás. . . . . . . . . . . . . . . . . . .286

EN

DE

FR

ES

PT

IT

NL

DA

SV

NO

FI

RU

PL

SK

CS

HU

COOLING BOXES

COOLFREEZE

CDF18-26-36-46--O-16s.book Seite 1 Dienstag, 25. Juli 2017 1:16 13

CoolFreeze

2

1

2

1

12/24V DC

COLD FREEZE

ERROR

POWER

HIGH

0

LOW

TEMPERATURE BATTERY MONITOR

1

CDF18

2 3 4

5

2

12/24V DC

CDF26, CDF36, CDF46

3

ERROR

POWER

°

CDF26

1

34

5 6 7

2

4

CDF18-26-36-46--O-16s.book Seite 2 Dienstag, 25. Juli 2017 1:16 13

CoolFreeze

3

ERROR

POWER

°

CDF36, CDF46

1

34

5 6

2

5

1

6

1 2 3

4

5

6

7

CDF26, CDF36, CDF46

1 2

8

CDF18-26-36-46--O-16s.book Seite 3 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze

4

Please read this operating manual carefully before starting the device.

Keep it in a safe place for future reference. If the device is passed on to

another person, this operating manual must be handed over to the user

along with it.

The manufacturer cannot be held liable for damage resulting from improper usage

or incorrect operation.

Contents

1 Explanation of symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

3 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

4 Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

5 Intended use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

6 Function description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

7 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

8 Cleaning and maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

9 Guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

10 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

11 Disposal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

12 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

CDF18-26-36-46--O-16s.book Seite 4 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Explanation of symbols

5

1 Explanation of symbols

!

A

I

2 Safety instructions

2.1 General safety

!

WARNING!

• Do not operate the cooling device if it is visibly damaged.

• If this cooling device's power cable is damaged, it must be replaced

by the manufacturer, customer service or a similarly qualified person in

order to prevent safety hazards.

• This cooling device may only be repaired by qualified personnel.

Improper repairs can lead to considerable hazards.

• This cooling device can be used by children aged 8 years or over, as

well as by persons with diminished physical, sensory or mental capac-

ities or a lack of experience and/or knowledge, providing they are

supervised or have been taught how to use the cooling device safely

and are aware of the resulting risks.

• Cleaning and user maintenance must not be carried out by children

without supervision.

• Children must not play with the cooling device.

WARNING!

Safety instruction: Failure to observe this instruction can cause fatal or

serious injury.

CAUTION!

Safety instruction: Failure to observe this instruction can lead to injury.

NOTICE!

Failure to observe this instruction can cause material damage and impair

the function of the product.

NOTE

Supplementary information for operating the product.

CDF18-26-36-46--O-16s.book Seite 5 Dienstag, 25. Juli 2017 1:16 13

EN

Safety instructions CoolFreeze

6

• Children must be supervised to ensure that they do not play with the

cooling device.

• Always keep and use the cooling device out of the reach of children

under the age of 8 years.

• Do not store any explosive substances such as spray cans with a

flammable propellant in the cooling device.

!

CAUTION!

• Disconnect the cooling device from the power supply

– before each cleaning and maintenance

– after every use

• Food may only be stored in its original packaging or in suitable

containers.

A

NOTICE!

• Check that the voltage specification on the type plate corresponds to

that of the energy supply.

• Only connect the cooling device to a DC power supply in the vehicle

with the DC cable.

• Never pull the plug out of the socket by the cable.

• Disconnect the cooling device and other power consuming devices

from the battery before connecting a quick charging device.

• Disconnect the cooling device or switch it off when you turn off the

engine. Otherwise you may discharge the battery.

• The cooling device is not suitable for transporting caustic materials or

materials containing solvents.

• The insulation of the cooling device contains flammable cyclopentane

and requires special disposal procedures. Deliver the cooling device

at the end of its life-cycle to an appropriate recycling.

2.2 Operating the cooling device safely

!

CAUTION!

• Before starting the cooling device, ensure that the power supply line

and the plug are dry.

A

NOTICE!

• Do not use electrical devices inside the cooling device unless they are

recommended by the manufacturer for the purpose.

CDF18-26-36-46--O-16s.book Seite 6 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Scope of delivery

7

• Do not place the cooling device near naked flames or other heat

sources (heaters, direct sunlight, gas ovens etc.).

• Danger of overheating!

Ensure at all times that there is sufficient ventilation so that the heat that

arises during operation does not build up. Make sure that the cooling

device is sufficiently far away from walls and other objects so that the

air can circulate.

• Ensure that the ventilation openings are not covered.

• Do not fill the inner container with ice or fluid.

• Never immerse the cooling device in water.

• Protect the cooling device and the cable against heat and moisture.

3Scope of delivery

fig. 1, page 2, shows the scope of delivery.

4Accessories

To operate the cooler using an AC power supply, we recommend using the

following mains adapter.

Available as accessory (not included in scope of delivery):

• 220–240 V: CoolPower EPS100

• 110–240 V: CoolPower MPS35

Item Quantity Description

1 1 Compressor cooler

2 1 Connection cable for DC connection

– 1 Operating manual

CDF18-26-36-46--O-16s.book Seite 7 Dienstag, 25. Juli 2017 1:16 13

EN

Intended use CoolFreeze

8

5 Intended use

The compressor cooler is suitable for cooling and freezing foodstuffs. The compres-

sor cooler is also suitable for use on boats.

The compressor cooler is designed to be operated from a 12 Vg or 24 Vg on-

board socket of a vehicle (e.g. DC socket), boat or mobile home.

I

!

6 Function description

The cooler can chill products, keep them cool as well as freeze them. A mainte-

nance-free, CFC-free refrigerant circuit with compressor provides the cooling. The

extra strong CFC-free insulation and powerful compressor ensure especially fast

cooling.

The cooler is designed for mobile use.

When used on boats, the cooler can be withstand a short-term heel (inclination)

of 30°.

An integrated dual-stage (CDF18) / three-stage (CDF26, CDF36, CDF46) battery

monitor prevents your vehicle battery from excessive discharging.

NOTE

To operate the device at the AC mains supply, we recommend using

one of the following rectifiers:

• 220–240 V: CoolPower EPS100

• 110–240 V: CoolPower MPS35

CAUTION! Health hazard!

Please check if the cooling capacity of the device is suitable for storing

the food or medicine you wish to cool.

CDF18-26-36-46--O-16s.book Seite 8 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Function description

9

6.1 Operating and display elements

CDF18

Operating panel and connection socket (fig. 2, page 2):

Item Description Explanation

1 TEMPERATURE Temperature controller,

cooling temperature at the end positions:

COLD: +10 °C

FREEZE: –18 °C

2 POWER Operating display

LED is lit green: Device is switched on and ready for

operation

LED is lit yellow: Set temperature has been reached

3 ERROR LED flashes red: Switched on device is not ready for

operation

4 BATTERY MONITOR Switch-on device/battery monitor:

0: Device is switched off

HIGH: Device is switched on, battery

monitor is in HIGH mode

LOW: Device is switched on, battery

monitor is in LOW mode

5 12/24V DC Connection socket DC voltage supply

CDF18-26-36-46--O-16s.book Seite 9 Dienstag, 25. Juli 2017 1:16 13

EN

Function description CoolFreeze

10

CDF26

Connection socket (fig. 3, page 2) and operating panel (fig. 4, page 2):

Item Description Explanation

1ON

OFF button

Switches the cooler on or off when the button is pressed for

between one and two seconds

2 POWER Status indication

LED lights up green: Compressor is on

LED lights up orange: Compressor is off

LED flashes orange: Display switched off auto-

matically due to low battery

voltage

3 ERROR LED flashes red: Device is switched on but not

ready for operation

4 SET Selects the input mode

Temperature setting

Celsius or Fahrenheit display

Set battery monitor

5 – Display, shows the information

The first three digits of the four-digit display show the

temperature, the fourth digit shows the temperature unit

(°C or °F).

6 UP + Press once to increase the value

7 DOWN – Press once to decrease the value

CDF18-26-36-46--O-16s.book Seite 10 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Function description

11

CDF36, CDF46

Connection socket (fig. 3, page 2) and operating panel (fig. 5, page 3):

Item Description Explanation

1 ON/OFF button Switches the cooler on or off when the button is pressed for

between one and two seconds

2 POWER Status indication

LED lights up green: Compressor is on

LED lights up orange: Compressor is off

LED flashes orange: Display switched off automatically

due to low battery voltage

3 ERROR LED flashes red: Device is switched on but not ready

for operation

4 SET Selects the input mode

Temperature setting

Celsius or Fahrenheit display

Set battery monitor

5 – Display, shows the information

The first three digits of the four-digit display show the

temperature, the fourth digit shows the temperature unit

(°C or °F).

6 ADJUST Press once to increase the value

Press once to decrease the value

CDF18-26-36-46--O-16s.book Seite 11 Dienstag, 25. Juli 2017 1:16 13

EN

Operation CoolFreeze

12

7Operation

7.1 Before initial use

I

7.2 Energy saving tips

• Choose a well ventilated installation location which is protected against direct

sunlight.

• Allow warm food to cool down first before placing it in the cooling device to

keep cool.

• Do not open the cooling device more often than necessary.

• Do not leave the cooling device open for longer than necessary.

• Defrost the cooler once a layer of ice forms.

• Avoid unnecessary low temperatures.

7.3 Connecting the cooler

!

A

➤ Plug the 12/24-V connection cable (fig. 1 2, page 2) into the DC voltage

socket and also into the cigarette lighter or a 12 V or 24 V socket.

NOTE

Before starting your new cooler for the first time, you should clean it

inside and outside with a damp cloth for hygienic reasons (please also

refer to the chapter “Cleaning and maintenance” on page 18).

WARNING!

• Connect the device with the supplied DC cable only.

• Do not modify the DC cable. Modifying the DC cable may cause

safety risks.

• The DC cable must always be protected by 8 A fuse.

NOTICE! Danger of damaging the device!

Disconnect the cooler and other consumer units from the battery before

you connect the battery to a quick charging device.

Overvoltage can damage the electronics of the device.

CDF18-26-36-46--O-16s.book Seite 12 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Operation

13

7.4 Using the battery monitor

If the cooler is operated when the vehicle ignition is switched off, the cooler switches

off automatically as soon as the supply voltage falls below a set level. The cooler will

switch back on once the battery has been recharged to the restart voltage level.

A

In “HIGH” mode, the battery monitor responds faster than at the levels “LOW” and

“MED” (see the following table).

CDF18

CDF26, CDF36, CDF46

I

NOTICE! Danger of damage!

When switched off by the battery monitor, the battery will no longer be

fully charged. Avoid starting repeatedly or operating current consumers

without longer charging phases. Ensure that the battery is recharged.

Battery monitor mode LOW HIGH

Switch-off voltage at 12 V

10,2 V ± 0,3 V 11,2 V ± 0,3 V

Restart voltage at 12 V

11,2 V ± 0,3 V 12,2 V ± 0,3 V

Switch-off voltage at 24 V

22,0 V ± 0,3 V 23,9 V ± 0,3 V

Restart voltage at 24 V

23,3 V ± 0,3 V 25,1 V ± 0,3 V

Battery monitor mode LOW MED HIGH

Switch-off voltage at 12 V

10,1 V 11,4 V 11,8 V

Restart voltage at 12 V

11,1 V 12,2 V 12,6 V

Switch-off voltage at 24 V

21,5 V 24,1 V 24,6 V

Restart voltage at 24 V

23,0 V 25,3 V 26,2 V

NOTE

When the cooler is supplied by the starter battery, select the battery

monitor mode “HIGH”. If the cooler is connected to a supply battery,

the battery monitor mode “LOW” will suffice.

If you wish to operate the cooler from the AC mains, set the battery

monitor to the “LOW” position.

CDF18-26-36-46--O-16s.book Seite 13 Dienstag, 25. Juli 2017 1:16 13

EN

Operation CoolFreeze

14

CDF26: Setting the battery monitor mode

This is how to select the battery monitor mode:

➤ Switch on the cooler.

➤ Press the “SET” button three times.

➤ Use the “+” and “–” buttons to select the battery monitor mode.

✓ The selected mode then appears in the display for a few seconds. The display

flashes several times before it returns to the current temperature.

CDF36, CDF46: Setting the battery monitor mode

This is how to select the battery monitor mode:

➤ Switch on the cooler.

➤ Press the “SET” button three times.

➤ Use the “ADJUST” button to select the battery monitor mode.

7.5 Using the cooler

A

➤ Place the cooler on a firm foundation.

Make sure that the ventilation slots are not covered and that the heated air can

dissipate.

➤ Close the cooler, see chapter “Connecting the cooler” on page 12.

A

Locking the cooler

➤ Close the lid.

➤ Press the lock (fig. 6 1, page 3) down, until it latches in place audibly.

NOTICE! Danger of overheating!

Ensure at all times that there is sufficient ventilation so that the heat that

generated during operation can dissipate. Ensure that the ventilation

slots are not covered. Make sure that the device is sufficiently far away

from walls and other objects so that the air can circulate.

NOTICE! Danger from excessively low temperature!

Ensure that the only those objects are placed in the cooler that are

intended to be cooled at the selected temperature.

CDF18-26-36-46--O-16s.book Seite 14 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Operation

15

CDF18: Switching on the cooler

➤ Slide the sliding switch “BATTERY MONITOR” to HIGH if you wish to operate

from a starter battery or to “LOW” if you want to operate from a supply battery.

✓ The “POWER” LED is lit green.

✓ The cooler starts cooling the interior.

➤ Set the cooling temperature with the temperature controller “TEMPERATURE”.

✓ When the cooling temperature has been reached, the “POWER” LED is lit yellow.

CDF26, CDF36, CDF46: Switching on the cooler

➤ Press the “ON/OFF” button for three seconds.

✓ The “POWER” LED is lit green.

✓ The display switches on and shows the current cooling temperature.

✓ The cooler starts cooling the interior.

CDF18: Switching off the cooler

➤ Empty the cooler.

➤ To Switch the cooler off: Slide the sliding switch “BATTERY MONITOR” to “0”:

➤ Pull out the connection cable.

If you do not want to use the cooler for a longer period of time:

➤ Leave the cover slightly open. This prevents odour build-up.

CDF26, CDF36, CDF46: Switching off the cooler

➤ Empty the cooler.

➤ Switch the cooler off.

➤ Unplug the connection cable.

If you do not want to use the cooler for a longer period of time:

➤ Leave the lid slightly open. This prevents build-up of odours.

CDF18-26-36-46--O-16s.book Seite 15 Dienstag, 25. Juli 2017 1:16 13

EN

Operation CoolFreeze

16

7.6 Setting the temperature

CDF26

➤ Press the “SET” button once.

➤ Use the “+” and “–” buttons to set the cooling temperature.

✓ The set cooling temperature then appears in the display for a few seconds. The

display flashes several times before it returns to the current temperature.

CDF36, CDF46

➤ Press the “SET” button once.

➤ Use the “ADJUST” button to set the cooling temperature.

✓ The set cooling temperature then appears in the display for a few seconds. The

display flashes several times before it returns to the current temperature.

7.7 Selecting the temperature unit

CDF26

You can switch the temperature display between Celsius and Fahrenheit. To do this,

proceed as follows:

➤ Switch on the cooler.

➤ Press the “SET” button twice.

➤ Use the “+” and “–” buttons to set the cooling temperature.

✓ The set temperature unit then appears in the display for a few seconds. The dis-

play flashes several times before it returns to the current temperature.

CDF36, CDF46

You can switch the temperature display between Celsius and Fahrenheit. To do this,

proceed as follows:

➤ Switch on the cooler.

➤ Press the “SET” button twice.

➤ Use the “ADJUST” button to set the Celsius or Fahrenheit temperature unit.

CDF18-26-36-46--O-16s.book Seite 16 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Operation

17

7.8 Defrosting the cooler

Humidity can form frost in the interior of the cooling device or on the vaporiser. This

reduces the cooling capacity. Defrost the device in good time to avoid this.

A

To defrost the cooler, proceed as follows:

➤ Take out the contents of the cooling device.

➤ If necessary, place them in another cooling device to keep them cool.

➤ Switch off the device.

➤ Leave the cover open.

➤ Wipe off the defrosted water.

7.9 Replacing the plug fuse (12/24 V)

➤ Pull the adapter sleeve (fig. 7 4, page 3) off of the plug.

➤ Unscrew the screw (fig. 7 5, page 3) out of the upper half of the housing

(fig. 7 1, page 3).

➤ Carefully raise the upper half of the housing from the lower (fig. 7 6, page 3)

half.

➤ Take out the contact pin (fig. 7 3, page 3).

➤ Replace the defective fuse (fig. 7 2, page 3) with a new one that has the same

rating (8A 32V).

➤ Re-assemble the plug in the reverse order.

7.10 Replacing the light bulb (CDF26, CDF36, CDF46)

➤ Press the switch pin (fig. 8 2, page 3) downwards so that the transparent part

(fig. 8 1, page 3) of the lamp can be removed at the front.

➤ Replace the light bulb.

➤ Press the lamp back into the housing.

NOTICE! Danger of damaging the device!

Never use hard or pointed tools to remove ice or to loosen objects

which have frozen in place.

CDF18-26-36-46--O-16s.book Seite 17 Dienstag, 25. Juli 2017 1:16 13

EN

Cleaning and maintenance CoolFreeze

18

8 Cleaning and maintenance

!

A

➤ Occasionally clean the device interior and exterior with a damp cloth.

➤ Make sure that the air inlet and outlet vents on the device are free of any dust and

dirt, so that heat can be released and the device is not damaged.

9Guarantee

The statutory warranty period applies. If the product is defective, please contact the

manufacturer's branch in your country (see the back of the instruction manual for the

addresses) or your retailer.

For repair and guarantee processing, please include the following documents when

you send in the device:

• A copy of the receipt with purchasing date

• A reason for the claim or description of the fault

WARNING!

Always disconnect the device from the power supply before you clean

and service it.

NOTICE! Risk of damage

• Never clean the cooler under running water or in dish water.

• Do not use abrasive cleaning agents or hard objects during cleaning

as these can damage the cooler.

CDF18-26-36-46--O-16s.book Seite 18 Dienstag, 25. Juli 2017 1:16 13

EN

CoolFreeze Troubleshooting

19

10 Troubleshooting

11 Disposal

➤ Place the packaging material in the appropriate recycling waste bins wherever

possible.

M

If you wish to finally dispose of the product, ask your local recycling centre

or specialist dealer for details about how to do this in accordance with the

applicable disposal regulations.

Fault Possible cause Suggested remedy

Device does not

function, LED does not

glow.

No voltage is flowing

from the DC power

socket in your vehicle.

The ignition must be switched on in

most vehicles to supply current to the

DC power socket.

No voltage present in

the AC voltage socket.

Try using another plug socket.

The device does not

cool (plug is inserted,

POWER LED is lit).

Defective compressor. This can only be repaired by an

authorised repair centre.

The device does not

cool (plug is inserted,

ERROR LED flashes).

Battery voltage is too

low.

Test the battery and charge it as needed.

When operating from

the DC power socket:

The ignition is on and

the device is not work-

ing and the LED is not

lit.

Pull the plug out of the

socket and make the

following checks.

The DC socket is dirty.

This results in a poor

electrical contact.

If the plug of your cooler becomes very

warm in the DC socket, either the socket

must be cleaned or the plug has not

been assembled correctly.

The fuse of the 12/24 V

plug has blown.

Replace the fuse in the 12 V plug, see

chapter “Replacing the plug fuse

(12/24 V)” on page 17.

The vehicle fuse has

blown.

Replace the vehicle's 12/24 V socket

fuse (usually 15 A). Please refer to your

vehicle's operating manual.

ERROR LED flashes for

longer than 2 minutes,

as follows: 3 flashes,

pause, 3 flashes,

pause, ...

Defective device. This can only be repaired by an

authorised repair centre.

CDF18-26-36-46--O-16s.book Seite 19 Dienstag, 25. Juli 2017 1:16 13

EN

Technical data CoolFreeze

20

12 Technical data

CDF18 CDF26

Ref. no.: 9600000460 9600000601

Contains: 18 l 21 l

Voltage: 12/24 Vg

Rated current

12 Vg:3.5A 5.0A

24 Vg:1.9A 2.5A

Cooling capacity: +10 °C to –18 °C

Climate class: N or T

Ambient temperature: +16 °C – +43 °C

Refrigerant quantity: 32 g 35 g

CO

2

equivalent: 0.046 t 0.050 t

Global warming potential (GWP): 1430

Dimensions (W x H x D) in mm: 465 x 414 x 300 550 x 425 x 260

Weight: 9.5 kg 12.7 kg

Tests/

Certification:

4

CDF18-26-36-46--O-16s.book Seite 20 Dienstag, 25. Juli 2017 1:16 13

La page charge ...

Dometic CDF18, CDF26, CDF36, CDF46 Mode d'emploi

Ce manuel convient également à

Dometic CDF18, CDF26, CDF36, CDF46 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents