Faber Tratto 30 SSV with VAM Guide d'installation

GLAS30SSV

GLAS36SSV

GLASSY 30"

GLASSY 36"

TRATTO 30"

TRATTO 36"

TRAT30SSV

TRAT36SSV

Installation Instructions

Use and Care Information

Instructions d'installation

Utilisez et d'entretien

Instrucciones de instalación

Información de uso y cuidado

2

READ AND SAVE THESE INSTRUCTIONS BEFORE YOU START

INSTALLING THIS RANGEHOOD

WARNING: - TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

a) Never leave surface units unattended at high settings. Boilovers cause smoking and

greasy spillovers that may ignite. Heat oils slowly on low or medium setting.

b)AlwaysturnhoodONwhencookingathighheatorwhenambeingfood(i.e.Crepes

Suzette, Cherries Jubilee, Peppercorn Beef Flambé).

c) Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan

orlter.

d) Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING: - TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

a)SMOTHERFLAMESwithaclose-ttinglid,cookiesheet,ormetaltray,thenturnofftheburner.

BECAREFULTOPREVENTBURNS.IftheamesdonotgooutimmediatelyEVACUATE

AND CALL THE FIRE DEPARTMENT.

b) NEVER PICK UP A FLAMING PAN - You may be burned.

c) DO NOT USE WATER, including wet dishcloths or towels - a violent steam explosion will

result.

d) Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

2. Thereissmallandcontainedintheareawhereitstarted.

3. Theredepartmentisbeingcalled.

4. Youcanghttherewithyourbacktoanexit.

* Based on "Kitchen Firesafety Tips" published by NFPA

WARNING - TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not use this

fan with any solid-state speed control device.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have any

questions, contact the manufacturer.

2. Before servicing or cleaning unit, switch power off at service panel and lock the

service disconnecting means to prevent power from being switched on acciden-

tally. When the service disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

CAUTION: For General Ventilating Use Only. Do Not Use To Exhaust Hazardous or

Explosive Materials and Vapors.

WARNING - TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO

PERSONS, OBSERVE THE FOLLOWING:

1. InstallationWorkAndElectricalWiringMustBeDoneByQualiedPerson(s)InAccor-

dance With All Applicable Codes And Standards, Including Fire-Rated Construction.

2. Sufcientairisneededforpropercombustionandexhaustingofgasesthrough

theue(chimney)offuelburningequipmenttopreventbackdrafting.Followthe

heating equipment manufacturer's guideline and safety standards such as those

publishedby theNational FireProtectionAssociation (NFPA), andthe American

SocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE),and

the local code authorities.

3

ALL WALL AND FLOOR OPENINGS WHERE THE RANGEHOOD IS INSTALLED MUST

BE SEALED.

This rangehood requires at least 24" of clearance between the bottom of the rangehood and the

cooking surface or countertop. This hood has been approved by UL at this distance from the cooktop.

This minimum clearance may be higher depending on local building codes. For gas cooktops and

combination ranges, a minimum of 30" is recommended and may be required.

Overhead cabinets on both sides of this unit must be a minimum of 18" above the cooking surface

or countertop. Consult the cooktop or range installation instructions given by the manufacturer before

making any cutouts.

MOBILE HOME INSTALLATION The installation of this rangehood must conform to the Manufactured

Home Construction and Safety Standards, Title 24 CFR, Part 3280 (formerly Federal Standard for Mobile

Home Construction and Safety, Title 24, HUD, Part 280). See Electrical Requirements.

• Venting system MUST terminate outside the home.

• DO NOT terminate the ductwork in an attic or other enclosed space.

• DO NOT use 4" laundry-type wall caps.

• Flexible-type ductwork is not recommended.

• DO NOT obstruct the ow of combustion and ventilation air.

• Failure to follow venting requirements may result in a re.

WARNING

!

VENTING REQUIREMENTS

Determine which venting method is best for your application. Ductwork can extend either through the

wall or the roof.

The length of the ductwork and the number of elbows should be kept to a minimum to provide efcient

performance. The size of the ductwork should be uniform. Do not install two elbows together. Use

duct tape to seal all joints in the ductwork system. Use caulking to seal exterior wall or oor opening

around the cap.

Flexible ductwork is not recommended. Flexible ductwork creates back pressure and air turbulence

that greatly reduces performance.

Make sure there is proper clearance within the wall or oor for exhaust duct before making cutouts.

Do not cut a joist or stud unless absolutely necessary. If a joist or stud must be cut, then a supporting

frame must be constructed.

WARNING - To Reduce The Risk Of Fire, Use Only Metal Ductwork.

CAUTION-Toreduceriskofreandtoproperlyexhaustair,besuretoductairoutside–Do

not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.

3. When cutting or drilling into wall or ceiling, do not damage electrical wiring and

other hidden utilities.

4. Ducted fans must always be vented to the outdoors.

4

• Electrical ground is required on this rangehood.

• If cold water pipe is interrupted by plastic, nonmetallic gaskets or other materials, DO

NOT use for grounding.

• DO NOT ground to a gas pipe.

• DO NOT have a fuse in the neutral or grounding circuit. A fuse in the neutral or

grounding circuit could result in electrical shock.

• Check with a qualied electrician if you are in doubt as to whether the rangehood is

properly grounded.

• Failure to follow electrical requirements may result in a re.

WARNING

!

StateofCaliforniaProposition65Warning(USonly)

WARNING

This product contains chemicals known to the State of California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.P65Warnings.ca.gov

5

RANGEHOOD DIMENSIONS

15

3/4

’’

11

13/16

’’

5

3/4

’’

4

3/4

’’

9

1/8

’’

4

15/16

’’

3-

15/16

’’

14

3/16

’’

6

1

/

5

1

4

’’

8

/

1

52

’’

6

1

/

5

1

9

’’

8

/

1

3

’’4/1

’’

6

1

/

7

1

2

9/16

’’

10

1/4

’’

´

´

1

2.2

2.1

10

7.2.1

12a

12b

12c

7.3

12d

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

7.2.1 2 Upper Chimney Section Fixing

Brackets

7.3 1 Cooker Hood Fixing Brackets

12a 6 Screws 3/16" x 1 3/4"

12b 4 Screws 1/8" x 3/8"

12c 2 Screws

12d 2 Screws 1/8" x 3/8"

Qty. Documentation

1 Instruction Manual

GLASSY 30" GLASSY 36"

6

RANGEHOOD DIMENSIONS

TRATTO 30" TRATTO 36"

’’

8

/

1

52

´

´

MAIN PARTS

Components

Ref. Qty. Product Components

1 1 Hood Body, complete with: Con-

trols, Light, Filters, Blower.

2 1 Telescopic Chimney comprising:

2.1 1 Upper Section

2.2 1 Lower Section

10 1 Damper ø 5 7/8"

Ref. Qty. Installation Components

7.2.1 2 Upper Chimney Section Fixing

Brackets

7.3 1 Cooker Hood Fixing Brackets

12a 6 Screws 3/16" x 1 3/4"

12b 4 Screws 1/8" x 3/8"

12c 2 Screws

12d 2 Screws 1/8" x 3/8"

Qty. Documentation

1 Instruction Manual

2.2

2.1

10

7.2.1

12b

12c

7.3

1

12d

12a

7

Available Accessories

- Direct Connect Wiring Box sku # WIREBOX

- High Ceiling Chimney Kit - Upper and Lower Chimney Flue to replace the original ue's

to t up to 11' ceilings - sku# HIGH3

- Ductless Kit - Includes Ductless Diverter, Charcoal Filters - sku# DUCT4

- Activated Charcoal Filter Accessory - sku# FILTER2

- Wireless Remote Control Accessory - REMCTRL2

Parts needed

- 6" Round Metal ductwork

Min. 24" Min. 30''

8







H

I



Install Damper that is included with the Hood

before connecting to the ductwork.

Only for Ducted Venting Installation

Choose your ducting method

Non Ducted - RecirculationDucted Venting Installation

Requires

purchase of

Activated

Charcoal

Accessory

Horizontal

Vertical

6 "

9

2











x6











x6







12 1/16”

4 9/16”





´

>

´

24”

30”

4 9/16”

7.2.1

2.1

Draw a horizontal line where indicated above the hob.

Place a bracket 7.2.1 on the wall as shown about 1 1/8" from the ceiling or upper limit, aligning the center

(notch) with the vertical reference line and mark the wall at the centers of the holes in the bracket.

Place the second bracket 7.2.1 on the wall as shown, below the rst bracket, at the height of the

upper chimney section supplied and aligning the center (notch) with the vertical line.

Mark the wall at the centers of the holes in the bracket and mark the point 1 and 2 for the Hood Body

installation as shown(12 1/16" from the horizontal line and 4 9/16" from the vertical line).

Drill ø 5/16" holes at all the center points marked (point 1,2,3,4,5,6) as shown.

1

Draw a vertical line on the supporting wall as high as practical, at the center of the area in which

the hood will be installed.

Draw a horizontal line at where the bottom edge of the hood will be located as indicated in the gure

that is a minimum of 24" - 30" above cooking surface.

10

7

3

4

5

6

I = 6x

2X

12a

Installation screws provided must be secured

with wall plugs (purchase separately).

Insert the two screws 12a supplied with the hood

into the Fixing Bracket as shown and do not

tighten all the way to wall leaving 3/16" of the

screw heads exposed.

Use a level to insure that Fixing Bracket is level and

then fully secure the two screws.

Hook the hood body onto the hood body xing

bracket 7.3.

I = 6x

11

8

Install Roof or Wall

Cap purchased

separately. Con-

nect the 6" metal

ductwork to the

Roof or Wall Cap

and then attach

ductwork.

Vertical or Horizontal

Ducting Installation

12c

Tighten the 2 screws 12c as shown.

11

9

L = 4x

Install the 2 xing brackets 7.2.1 to the middle and

upper holes and secure with screws 12a as shown.

10

11

2.1

Slightly widen

the two sides

of the upper

chimney and

hook them

behind the

brackets 7.2.1,

making sure

that they are

well seated.

Secure the sides to the brackets by using the 4

screws 12b.

12a

13

Slightly widen the two

sides of the the lower

chimney hood and hook

them between

the upper section and the

wall, making sure that they

are properly housed.

Fix the the

lower chim-

ney hood

laterally to

the hood

body using

the 2 screws

12d supplied.

12

2.2

2.1

N = 2x

12d

N = 4x

12b

12

16 17

18

2.1

Fix the Ductless Diverter with two screws 12a supplied

as shown.

Slightly widen

the two sides of

the upper chim-

ney and hook

them behind

the brackets

and connect to

the Ductless

Diverter, mak-

ing sure that

they are well

seated.

14 15

¡

12a

Only for the recirculation version, connect the hood

to the Air outlet.

Fix the lower Bracket 7.2.1 with two screws 12a

supplied as shown.

Non-Ducted Recirculation Option

N = 4x

12b

Secure the sides to the brackets by using the 4

screws 12b.

13

Direct Connect Wiring Box

Accessory sku # WIREBOX

(purchased separately)

Created by

-

Denomination

-

Lang EN

Sheet

1

/1

Modif.by

Approved by

Approval date

Doc. status

Drawing N.

NEW_DRAWING_BOX

Rev

01

ELECTRICAL INSTALLATION WITH CONNECTION

CABLE

GROUNDING INSTRUCTIONS This appliance must be

grounded. In the event of an electrical short circuit, grounding

reduces the risk of electric shock by providing an escape

wire for the electric current. This appliance is equipped

with a cord having a grounding wire with a grounding plug.

The plug must be plugged into an outlet that is properly

installed and grounded.

WARNING - Improper grounding can result in a risk of

electric shock.

Consult a qualied electrician if the grounding instructions

are not completely understood, or if doubt exists as to

whether the appliance is properly grounded.

Do not use an extension cord. If the power supply cord is

too short, have a qualied electrician install an outlet near

the appliance.

ELECTRICAL INSTALLATION WITH

OPTIONAL WIRING BOX

For Permanent wiring Installation-Use only

with Listed rangehood Wiring Box kit

sku # WIREBOX, manufactured by Faber.

Max. 33 7/16”

19

For Non-Ducted Recirculation

Option

Required Activated Charcoal Filter

Accessory - sku # - FILTER2

(purchased separately)

Attach a

charcoal

lter in the

correct

position and

block it by

the xing

hooks as

shown.

Unlock the xing hooks (towards the back of the

insert hood) to remove.

14

N = 2x

12d

2.2

2.1

20 21

Slightly widen the two

sides of the the lower

chimney hood and hook

them between

the upper section and the

wall, making sure that they

are properly housed.

Fix the the

lower chim-

ney hood

laterally to

the hood

body using

the 2 screws

12d supplied.

15

USE AND CARE INFORMATION

T1 T2 T3 T4 L

LT1 T2 T3 T4

For Best Results

Start the rangehood several minutes before cooking to develop proper airow. Allow the

rangehood to operate for several minutes after cooking is complete to clear all smoke and

odors from the kitchen.

T1. Fan off button:turn the blower Off. The fan can be operated by pressing any of the fan setting buttons.

Hold down this button for 2 seconds to activate Delay off function which will keep the fan on for 15

minutes and automatically shut off.

T2. Fan settings buttons: Low speed.

T3. Fan settings buttons: Medium speed.

T4. Fan settings buttons: High speed / Intensive speed.

Hold down the button for 2 seconds to activate the intensive speed, which is timed to run for 6

minutes. At the end of this time it will automatically return to the speed set before.Suitable to deal

with maximum levels of cooking fumes.

L. Light button: On/Off switch for the lights.

NOTE: If your product has had a CFM adjustment, refer to the CFM adjustment manual for the infor-

mation. Some motor speeds or functions may be reduced.

16

Cleaningmetalgreaselters

The lters must be cleaned every 2 months of

operation, or more frequently for particularly heavy

usage, and can be washed in a dishwasher.

• Remove the Filters one at a time, pushing them

towards the back of the unit and at the same time

pulling downward.

• Wash the Filters without bending them, and

leave them to dry completely before replacing.

(If the surface of the lter changes colour as time

goes by, this will have absolutely no effect on the

efciency of the lter itself.)

• Replace, taking care to ensure that the handle

faces forwards.

• No water can be present in lters before installing

back in hood.

Replacing Activated Charcoal Filter

The lter is not washable and cannot be regenerated,

and must be replaced approximately every 4 months

of operation, or more frequently for particularly heavy

usage.

• Remove the Filters one at a time, pushing them

towards the back of the unit and at the same time

pulling downward.

• Remove the saturated charcoal lter by releasing

the xing hooks.

• Fit the new lter and fasten it in its correct position.

• Replace, taking care to ensure that the handle

faces forwards.

CAUTION: When used in recirculation mode, to Re-

duce the Risk of Fire and Shock use only conversion

kit Model FILTER2.

Lighting Unit

• LED lights must be replaced by Faber factory authorized service.

17

Wiring Diagram

    

    

   

 

    

    

   









 

120V 60Hz

18

January 4, 2016

FABER CONSUMER WARRANTY & SERVICE

All Faber products are warranted against any defect in materials or workmanship for the original purchaser

for a period of 1 year from the date of original purchase (requires proof of purchase). This warranty covers

labor and replacement parts. Faber, at its option, may repair or replace the product or components

necessary to restore the product to good working condition. To obtain warranty service, contact the dealer

from whom you purchased the range hood, or the local Faber distributor. If you cannot identify a local Faber

distributor, contact us at (508) 358-5353 for the name of a distributor in your area.

The following is not covered by Faber's warranty:

1. Service calls to correct the installation of your range hood, to instruct you how to use your range hood, to

replace or repair house fuses or to correct house wiring or plumbing.

2. Service calls to repair or replace range hood light bulbs, fuses or filters. Those consumable parts are

excluded from warranty coverage.

3. Repairs when your range hood is used for other than normal, single-family household use.

4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation,

installation not in accordance with electrical or plumbing codes or Faber documentation, or use of products

not approved by Faber.

5. Replacement parts or repair labor costs for units operated outside the United States or Canada, including

any non-UL or C-UL approved Faber range hoods.

6. Repairs to the hood resulting from unauthorized modifications made to the range hood.

7. Expenses for travel and transportation for product service in remote locations and pickup and delivery

charges. Faber range hoods should be serviced in the home.

THIS WARRANTY DOES NOT ALLOW RECOVERY OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, WITHOUT

LIMITATION, DIRECT, INDIRECT, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, PERSONAL INJURY/WRONGFUL

DEATH OR LOST PROFITS FABER WARRANTY IS LIMITED TO THE ABOVE CONDITIONS AND TO THE WARRANTY PERIOD

SPECIFIED HEREIN AND IS EXCLUSIVE. EXCEPT AS EXPRESSLY SPECIFIED IN THIS AGREEMENT, FABER DISCLAIMS ALL

EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS, AND WARRANTIES INCLUDING, WITHOUT LIMITATION, ANY

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

.

This warranty gives you specific legal rights that may vary from state to state.

Model#: ______________________________ Serial #: _____________________________

19

VEUILLEZ LIRE ET CONSERVER LA PRÉSENTE NOTICE AVANT DE

COMMENCER L'INSTALLATION DE LA HOTTE DE CUISINE

AVERTISSEMENT:-POUR RÉDUIRE LE RISQUE D'UN FEU DE GRAISSE SUR LA TABLE DE

CUISSON:

a) Ne laissez jamais sans surveillance les éléments de la surface de cuisson à température élevée.

Les bouillonnements excessifs peuvent provoquer de la fumée et les débordements de graisse

peuvents'enammer.L'huiledoitêtrechaufféelentement,àunetempératurebasseoumoyenne.

b) Assurez-vous de toujours mettre en marche le ventilateur de la hotte lorsque vous cuisinez

àtempératureélevéeoupréparezunmetsambé(p.ex.crêpesSuzette,cerisesjubilé,bœuf

ambé).

c) Nettoyez régulièrement les ventilateurs d'aspiration. Assurez-vous de ne pas laisser de la graisse

s'accumulersurleventilateurouleltre.

d)Utiliseztoujoursdespoêlesetcasserolesdelatailleappropriée.Utiliseztoujoursdesustensiles

de cuisine de la taille adaptée à celle de l'élément chauffant.

AVERTISSEMENT:-POURPRÉVENIRLESBLESSURESENCASDEFEUDEGRAISSESURLA

TABLEDECUISSON,SUIVEZLESRECOMMANDATIONSSUIVANTES*:

a) ÉTOUFFEZ LES FLAMMES à l'aide d'un couvercle hermétique, d'une plaque à biscuits ou d'un

plateau métallique, puis éteignez le brûleur. FAITES ATTENTION AUX BRÛLURES. Si le feu ne

s'éteint pas immédiatement, QUITTEZ LES LIEUX ET APPELEZ LES POMPIERS.

b) NE PRENEZ JAMAIS UNE CASSEROLE EN FLAMME - Vous pourriez vous brûler.

c) N'UTILISEZ JAMAIS DE L'EAU, ni un linge à vaisselle ou un torchon mouillé, pour éteindre le feu.

Cela pourrait provoquer une violente explosion de vapeur.

d)UtilisezunextincteurUNIQUEMENTsi:

1. Vousêtescertainqu'ils'agitd'unextincteurdeclasseABCetquevousconnaissezbienson

mode d'emploi.

2. Le feu est de faible intensité et se limite à l'endroit où il a démarré.

3. Les pompiers ont déjà été appelés.

4. Unevoiedesortiesetrouvederrièrevouspendantquevouséteignezlesammes

* D'après le guide «Kitchen Firesafety Tips» publié par la NFPA aux États-Unis

AVERTISSEMENT - POUR RÉDUIRE LE RISQUE D'INCENDIE OU DE CHOC ÉLECTRIQUE, n'utilisez

jamais ce ventilateur en association avec un dispositif de réglage de vitesse à semi-conducteurs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE

BLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:

1. Utilisez cet appareil uniquement de la façon prévue par le fabricant. Pour toute question, com-

muniquez avec le fabricant.

2. Avant de procéder à l'entretien ou au nettoyage de l'appareil, coupez l'alimentation au niveau du

panneau électrique et verrouillez-le pour vous assurer que l'électricité n'est pas rétablie accidentel-

lement.S'iln'estpaspossibledeverrouillerledispositifd'interruptiondel'alimentation,afchezde

façon ferme et bien visible un avis de danger, par exemple à l'aide d'une étiquette sur le panneau.

ATTENTION:Destinéàunusagedeventilationgénéraleuniquement.N'utilisezpascedispositif

pour l'aspiration de vapeurs ou de matériaux dangereux ou explosifs.

AVERTISSEMENT - POUR RÉDUIRE LES RISQUES D'INCENDIE, DE CHOC ÉLECTRIQUE OU DE

BLESSURECORPORELLE,RESPECTEZLESINSTRUCTIONSSUIVANTES:

1. L'installationet lebranchementélectriquedoivent êtreréalisésparuntechnicien qualiéet

conformément à tous les codes et normes en vigueur, incluant ceux concernant la construction

à l'épreuve du feu.

2. Andegarantirunecombustionetuneévacuationadéquatesdesgazparlesconduitesdela

cheminée des appareils à combustion, une bonne aération est nécessaire pour éviter le refou-

lement. Respectez les lignes directrices fournies par le fabricant du matériel chauffant, ainsi que

lesnormesdesécuritécommecellespubliéesparlaNationalFireProtectionAssociation(NFPA)

etlaAmericanSocietyforHeating,RefrigerationandAirConditioningEngineers(ASHRAE)aux

États-Unis, ainsi que les codes en vigueur dans votre région.

20

3. Lorsque vous faites une ouverture ou percez dans un mur ou le plafond, veillez à ne pas en-

dommagerleslsélectriquesoud'autresdispositifscachés.

4. Lesventilateurscanalisésdoiventtoujoursêtreraccordésàl'extérieur.

TOUTE OUVERTURE DANS LE MUR OU LE PLANCHER À PROXIMITÉ DE LA

HOTTE DOIT ÊTRE SCELLÉE.

Un espace libre d'au moins 24" est requis entre le bas de la hotte et la surface de cuisson ou le

comptoir. Cette hotte a été homologuée par l'UL à cette distance de la surface de cuisson.

L’espace libre minimal requis peut-être plus grand, selon la réglementation en matière de construction

de votre région. Pour les cuisinières à gaz et les cuisinières combinées, un espace minimal de 30" est

recommandé et pourrait être exigé.

Les armoires suspendues de chaque côté de l'appareil doivent se trouver à au moins 18" de la surface

de cuisson ou du comptoir. Consultez la notice d'installation de la surface de cuisson ou de la cuisinière

fournie par le fabricant avant de pratiquer des ouvertures.

INSTALLATION DANS UNE MAISON MOBILE L'installation de cette hotte doit être conforme à la Partie

3280 de la norme Manufactured Home Construction and Safety Standards, Title 24 CFR (précédemment

la partie 280 de la norme Federal Standard for Mobile Home Construction and Safety, Title 24, HUD).

Consultez la che technique électrique.

• Le système de ventilation DOIT déboucher à l'extérieur.

• NE FAITES PAS déboucher les conduits dans un grenier ou un autre endroit fermé.

• N'UTILISEZ PAS un clapet de sécheuse mural de 4po.

• Il n'est pas recommandé d'utiliser des conduits exibles.

• N'ENTRAVEZ PAS le ux de l'air de combustion et de ventilation.

• Le non-respect des exigences en matière de ventilation pourrait entraîner un incendie.

AVERTISSEMENT

!

CRITÈRES DE VENTILATION

Déterminez quelle méthode de ventilation est mieux adaptée à votre application. Les conduits peuvent

passer par le mur ou le toit.

Pour garantir une meilleure efcacité, la longueur des conduits et le nombre de coudes doivent être le plus

limités que possible. Le diamètre des conduits devrait être uniforme. N'installez pas deux coudes ensemble.

Utilisez un ruban pour canalisations an de sceller tous les joints du système de conduits. Utilisez un calfeu-

trage pour sceller les ouvertures dans le mur extérieur ou le plancher, autour du clapet.

Il n'est pas recommandé d'utiliser des conduits flexibles. Les conduits flexibles provoquent une contre-pression

et de la turbulence qui diminuent grandement l'efficacité de l'appareil.

Assurez-vous que l'espace libre dans le mur ou le plancher est sufsant pour le conduit d'évacuation avant de

pratiquer les ouvertures. Ne coupez jamais une poutre ou un chevron, sauf si c'est absolument nécessaire.

S'il s'avère nécessaire de couper une poutre ou un chevron, la construction d'un renforcement est requise.

AVERTISSEMENT - Pour réduire le risque d'incendie, utilisez uniquement des conduits métalliques.

ATTENTION - Pour réduire le risque d'incendie et pour évacuer adéquatement l'air, assurez-vous

deraccorderlesconduitsàl'extérieur–Nediffusezpasl'aird'évacuationdansdesespacesà

l'intérieur des murs ou du plafond, ou encore à l'intérieur d'un grenier, d'une galerie technique

ou d'un garage.

La page charge ...

Faber Tratto 30 SSV with VAM Guide d'installation

Ce manuel convient également à

Faber Tratto 30 SSV with VAM Guide d'installation

dans d''autres langues

Documents connexes