Zephyr AK7500BS Hood User Manual

Use, Care, and Installation Guide

www.zephyronline.com

Model number:

Serial Number:

OCT16.0401 © Zephyr Ventilation LLC.

Tempest II

AK7500BS

AK7536BS

AK7542BS

AK7548BS

AK7554BS

READ AND SAVE THESE INSTRUCTIONS

www.zephyronline.com

1

SAFETY NOTICE ................................................................. 2-3

LIST OF MATERIALS ....................................................... 4

INSTALLATION

Ducting Calculation Sheet

....................................... 5

Mounting Height & Clearance

................................ 6

Ducting Options

........................................................... 7

6SHFL¿FDWLRQV

............................................................... 8

Electrical

......................................................................... 9

Mounting the Range Hood

...................................... 10

Single Blower Horizontal Ducting Conversion

11-12

PBD-1200A Dual Blower Vertical Ducting

........ 13

PBD-1200A Dual Blower Horizontal Ducting

... 14

FEATURES & CONTROLS

Touch Controls

............................................................. 15-17

Optional Remote Control

......................................... 18

MAINTENANCE

Cleaning and Filter Removal

.................................. 19

Lights

................................................................................ 20

TROUBLESHOOTING

................................................................ 21

WIRING DIAGRAMS

................................................................... 22

FAN CURVE DIAGRAMS

......................................................... 23-24

LIST OF PARTS AND ACCESSORIES

.............................. 25

WARRANTY

.................................................................................... 26

PRODUCT REGISTRATION

.................................................... 28

Table of Contents

Important Safety Notice

READ AND SAVE THESE INSTRUCTIONS

2

www.zephyronline.com

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.

WARNING

TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.

b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.

When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service

panel.

CAUTION

For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning

agents or detergents. Suitable for use in household cooking area.

WARNING

TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:

a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly

on low or medium settings.

E $OZD\VWXUQKRRG21ZKHQFRRNLQJDWKLJKKHDWRUZKHQÀDPLQJIRRG

F &OHDQYHQWLODWLQJIDQVIUHTXHQWO\*UHDVHVKRXOGQRWEHDOORZHGWRDFFXPXODWHRQIDQRU¿OWHU

d. Use proper pan size. Always use cookware appropriate for the size of the surface element.

H .HHSIDQ¿OWHUVDQGJUHDVHODGHQVXUIDFHVFOHDQ

f. Use high setting on hood only when necessary.

g. Don’t leave hood unattended when cooking.

h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.

WARNING

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:

D 6027+(5)/$0(6ZLWKDFORVH¿WWLQJOLGFRRNLHVKHHWRUPHWDOWUD\WKHQWXUQRIIWKHEXUQHU%(&$5()8/7235(9(17%8516

,IWKHÀDPHVGRQRWJRRXWLPPHGLDWHO\(9$&8$7($1'&$//7+(),5('(3$570(17

b. NEVER PICK UP A FLAMING PAN – You may be burned.

c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.

d. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.

 7KH¿UHLVVPDOODQGFRQWDLQHGLQWKHDUHDZKHUHLWVWDUWHG

 7KH¿UHGHSDUWPHQWLVEHLQJFDOOHG

 <RXFDQ¿JKWWKH¿UHZLWK\RXUEDFNWRDQH[LW

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

D ,QVWDOODWLRQZRUNDQGHOHFWULFDOZLULQJPXVWEHGRQHE\TXDOL¿HGSHUVRQVLQDFFRUGDQFHZLWKDOODSSOLFDEOHFRGHVDQGVWDQGDUGV

,QFOXGLQJ¿UHUDWHGFRQVWUXFWLRQ

E 6XI¿FLHQWDLULVQHHGHGIRUSRZHUFRPEXVWLRQDQGH[KDXVWLQJRIJDVHVWKURXJKWKHÀXHFKLPQH\RIIXHOEXUQLQJHTXLSPHQWWRSUHYHQW

back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National

)LUH3URWHFWLRQ$VVRFLDWLRQ1)3$DQGWKH$PHULFDQ6RFLHW\IRU+HDWLQJ5HIULJHUDWLRQDQG$LU&RQGLWLRQLQJ(QJLQHHUV$6+5$(DQG

the local code authorities.

c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

d. Ducted fans must always vent to the outdoors.

e. NEVER place a switch where it can be reached from a tub or shower.

f. Make sure the power is off before installing, wiring or maintenancing.

Important Safety Notice

3

WARNING

TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

CAUTION

7RUHGXFHULVNRI¿UHDQGWRSURSHUO\H[KDXVWDLURXWVLGH'RQRWYHQWH[KDXVWDLULQWRVSDFHVZLWKLQZDOOVFHLOLQJV

attics, crawl spaces or garages.

OPERATION

$OZD\VOHDYHVDIHW\JULOOHVDQG¿OWHUVLQSODFH:LWKRXWWKHVHFRPSRQHQWVRSHUDWLQJEORZHUVFRXOGFDWFKRQWRKDLU¿QJHUV

and loose clothing.

The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,

maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to

negligence and the warranty of the unit automatically expires due to improper maintenance.

*NOTE: Please check www.zephyronline.com for revisions before doing any custom work.

ELECTRICAL REQUIREMENTS

Important:

Observe all governing codes and ordinances.

It is the customer’s responsibility:

 7RFRQWDFWDTXDOL¿HGHOHFWULFDOLQVWDOOHU

- To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70

latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and

all local codes and ordinances.

,IFRGHVSHUPLWDQGDVHSDUDWHJURXQGZLUHLVXVHGLWLVUHFRPPHQGHGWKDWDTXDOL¿HGHOHFWULFLDQGHWHUPLQHWKDWWKH

ground path is adequate.

Do not ground to a gas pipe.

&KHFNZLWKDTXDOL¿HGHOHFWULFLDQLI\RXDUHQRWVXUHWKHUDQJHKRRGLVSURSHUO\JURXQGHG

Do not have a fuse in the neutral or ground circuit.

*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269

** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit

protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to

Electrical Diagram on product.

$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWVSXUFKDVH

and install appropriate connector if necessary.

4

www.zephyronline.com

MODELS: AK7500BS, AK7536BS, AK7542BS, AK7548BS, AK7554BS

PARTS SUPPLIED

1 - Hood

%DIÀH¿OWHUV$.%6IRU$.%6$.%6IRU$.%6$.%6

2 - Halogen light bulbs, 4 for AK7548BS & AK7554BS

´URXQGVWDUWLQJFROODUfor single blower ducting

5HFWDQJXODUVWDUWLQJFROODUfor single blower horizontal ducting

7RSFRYHUSODWHIRUKRUL]RQWDOGXFWLQJ

1 - Hardware package

HARDWARE PACKAGE CONTENTS

PARTS NOT SUPPLIED

- Ducting, conduit and all installation tools

&DEOHFRQQHFWRULIUHTXLUHGE\ORFDOFRGHV

'XDO,QWHUQDO%ORZHU.LW3%'$

- Duct Cover Accessory

:RRG%RDUGWRKDQJKRRG:['[+

Light Bulb Removal

Suction Cup (1)

M6 x 1” (4)

M6 x 1-1/2” (4)

M6 x 2” (4)

M3.5 x 8 (8)

Wire Caps (3)

3/16 x 3/8 (4)

AK7500BS - 27” x 1/2” x 4”

AK7536BS - 33” x 1/2” x 4”

AK7542BS - 39” x 1/2” x 4”

AK7548BS - 45” x 1/2” x 4”

AK7554BS - 51” x 1/2” x 4”

List of Materials

5

Installation – Ducting Calculation Sheet

Duct pieces

Tot a l

Equivalent number

length x used =

3- 1/ 4” x 10”

Rect.,

straight

1 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

5 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. to

6” round

transition

90

0

elbow

20 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

90

0

15 Ft.

x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

45

0

9 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round,

straight

1 Ft. x ( ) =

Ft.

Subtotal column 1 =

Duct pieces

Tot a l

Equivalent number

length x used =

6”, 7”, 8”, 10”

Round, wall

cap with

damper

30 Ft. x ( ) =

Ft.

6”, 7”, 8”, 10”

Round

roof cap

30 Ft. x ( ) =

Ft.

Subtotal column 2 =

Subtotal column 1 =

Total ductwork =

Maximum Duct Length: For satisfactory air movement,

the total duct length

should not exceed 100 equivalent feet.

6” round to

3- 1/ 4” x 10”

rect.

transition

1 Ft. x ( ) =

Ft.

6” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

16 Ft. x ( ) =

Ft.

7” round to

3 1/4” x 10”

rect.

transition

8 Ft. x ( ) =

Ft.

7” round to

3- 1/ 4” x 10”

rect.

transition

90

0

elbow

23 Ft. x ( ) =

Ft.

elbow

7” to 6” or

8” to 7” Round

tapered

reducer

25 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

elbow

15 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 45

0

elbow

9 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect. 90

0

flat elbow

24 Ft. x ( ) =

Ft.

3- 1/ 4” x 10”

Rect.

wall cap

with damper

30 Ft. x ( ) =

Ft.

Ft. x ( ) =

Ft.

15

6”, 7“, 8”

Round

in-line

damper

Installation – Mounting Height & Clearance

6

www.zephyronline.com

DUCTING

A minimum of 8” round or 3-1/4” x 10” rectangular

GXFWPXVWEHXVHGWRPDLQWDLQPD[LPXPDLUÀRZ

HI¿FLHQF\IRUVLQJOHLQWHUQDOEORZHUDQG´URXQG

duct for dual internal blower.

Always use rigid type metal ducts only. Flexible

GXFWVFRXOGUHVWULFWDLUÀRZE\XSWR

$OVRXVHFDOFXODWLRQRQSDJHWRFRPSXWHWRWDO

available duct run when using elbows, transitions

and caps.

ALWAYS, when possible, reduce the number or

transitions and turns. If long duct run is required,

increase duct size.

If turns or transitions are required; install as far

away from hood duct output and as far apart,

between the two as possible.

Minimum mount height between range top to hood

bottom should be no less than 26”.

Maximum mount height should be no higher than

36”.

It is important to install the hood at the proper

mounting height. Hoods mounted too low could

UHVXOWLQKHDWGDPDJHDQG¿UHKD]DUGZKLOHKRRGV

mounted too high will be hard to reach and will

ORVHLWVSHUIRUPDQFHDQGHI¿FLHQF\

If available, also refer range manufacturer’s height

clearance requirements and recommended hood

mounting height above range.

Vertical Ducting:

´URXQGPLQLPXPVLQJOHLQWHUQDOEORZHU

´URXQGPLQLPXPGXDOLQWHUQDOEORZHU

Horizontal Ducting:

´URXQGPLQLPXPVLQJOHLQWHUQDOEORZHU

´[´PLQLPXPVLQJOHLQWHUQDOEORZHU

´URXQGPLQLPXPGXDOLQWHUQDOEORZHU

DAMAGE-SHIPMENT / INSTALLATION:

 3OHDVHIXOO\LQVSHFWXQLWIRUGDPDJHEHIRUH

installation.

 ,IWKHXQLWLVGDPDJHGLQVKLSPHQWUHWXUQWKH

unit to the store in which it was bought for

repair or replacement.

 ,IWKHXQLWLVGDPDJHGE\WKHFXVWRPHUUHSDLU

or replacement is the responsibility of the

customer.

 ,IWKHXQLWLVGDPDJHGE\WKHLQVWDOOHULIRWKHU

WKDQWKHFXVWRPHUUHSDLURIUHSODFHPHQWPXVW

be made by arrangement between customer

and installer.

36”

26” min.

36” max.

7

WARNING FIRE HAZARD

NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.

All exhaust must be ducted to the outside.

Use metal ductwork only.

)DVWHQDOOFRQQHFWLRQVZLWKVKHHWPHWDOVFUHZVDQGWDSHDOOMRLQWVZLWKFHUWL¿HG6LOYHU7DSHRU'XFW7DSH

Some Ducting Options

Installation – Ducting Options

Soffit or crawl space

Roof Pitch w/

Flashing & Cap

Rear Ducting

Side wall cap

w/ gravity damper

8

www.zephyronline.com

Installation – 6SHFL¿FDWLRQV

Top View

Side View

Back View

Ducting & Electrical Dimensions

12”

24”

4”

18”

8 9/16”

1 3/4”

1 1/16”

11 9/16”

6”

**7 7/8”

or

***10 3/8”

**9 1/2”

or

***14 3/16”

2 3/4”

**7 7/8”

or

***9 15/16”

R 9/16”

**7 7/8”

or

***10 3/8”

**1 15/16”

or

***4 5/16”

11 9/16”

10 3/4”

*3 3/16”

**7 7/8“

***10 3/8”

*9 7/8”

**9 1/2”

***14 3/16”

**7 7/8”

or

***9 15/16”

* Single Blower Rect. Ducting Dimension

** Single Blower Round Ducting Dimension

*** Dual Blower Dimension

1 11/16”

29 7/8” (30”)

35 7/8” (36”)

41 7/8“ (42”)

47 7/8” (48”)

53 7/8” (54”)

C/L

Back View

Mounting Dimensions

16 7/8”

16 1/8”

13 5/8”

1 11/16”

3 5/16”

21 1/4”

27 3/8” (36“ & 42”), 35 1/4” (48” & 54”)

5 5/16”

9

ELECTRICAL

WARNING

$OO(OHFWULFDOZRUNPXVWE\SHUIRUPHGE\TXDOL¿HGHOHFWULFLDQRUSHUVRQZLWKVLPLODUWHFKQLFDONQRZ

how and background.

For personal safety, remove house fuse or open circuit breaker before beginning installation. Do not use

extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and ordinances.

Electrical Supply:

This appliance requires a 120V 60Hz electrical supply, and connected to an individual, properly grounded

branch circuit, protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire w/

ground. Please also refer Electrical Diagram labeled on product.

Cable Lock:

$FDEOHORFNLQJFRQQHFWRUQRWVXSSOLHGPLJKWDOVREHUHTXLUHGE\ORFDOFRGHV&KHFNZLWKORFDOUHTXLUHPHQWV

and codes, purchase and install appropriate connector if necessary.

Installation – Electrical

Cable Lock

10

www.zephyronline.com

C/L

A

B

16 7/8”

min

26”

4”

wood board

FIG. 1

16 7/8”

16 1/8”

13 5/8”

1 11/16”

3 5/16”

21 1/4”

27 3/8” (36“ & 42”), 35 1/4” (48” & 54”)

5 5/16”

FIG. 2

Installation – Mounting the Range Hood

6HOHFWSUHIHUUHGGXFWLQJDSSOLFDWLRQYHUWLFDORUKRUL]RQWDODQG

prepare hood. Refer to page 11 for single blower horizontal

ducting, page 13 for dual blower vertical ducting or page 14 for

dual blower horizontal ducting.

2. Plum and mark center line on wall.

 &KRRVHGHVLUHGKHLJKWDERYHFRRNLQJVXUIDFH´PLQ/HYHO

DQGPDUNKRRGERWWRPOLQH$),*

 /HYHODQGPDUNWRSRIZRRGERDUGOLQH%),*´IURP

line A.

5. Mark center line of wood board. Center and align top of board with

OLQH%6HFXUHZRRGERDUGWRVWXGVXVLQJ0ZRRGVFUHZV

Wood Board Dimensions:['[+

AK7500BS - 27” x 1/2” x 4”

AK7536BS - 33” x 1/2” x 4”

AK7542BS - 39” x 1/2” x 4”

AK7548BS - 45” x 1/2” x 4”

AK7554BS - 51” x 1/2” x 4”

6. Prepare duct pipe and duct cut outs in upper cabinet if needed or

ZDOO,IKRUL]RQWDOO\GXFWLQJKRRG5HIHUWRKRRGVSHFL¿FDWLRQVRQ

page 8 for dimensions.

7. Prepare electrical wiring and electrical cut outs in upper cabinet if

needed or wall if horizontal electrical hook up is required. Refer to

KRRGVSHFL¿FDWLRQVRQSDJHIRUGLPHQVLRQV

 0RXQWKRRGRQWRZRRGERDUGDQGVHFXUHXVLQJ0ZRRG

screws.

9. Further secure hood onto wall through lower body screw holes by

0ZRRGVFUHZV6HHGLPHQVLRQVLQ),*

10. Install electrical.

,QVWDOOGXFWZRUNDQGVHDOZLWKFHUWL¿HGDOXPLQXPGXFWWDSH

12. Power up hood and check for leaks around duct tape.

,QVWDOOEDIÀH¿OWHUV

CAUTION: At least two installers are required

due to the weight and size of the hood.

!

WARNING: Electrical wiring must be done by a qualified person(s) in

accordance with all applicable codes and standards. This range hood must be

properly grounded. Turn off electrical power at service entrance before wiring.

!

11

1. Disconnect blower plug.

 5HPRYHVFUHZVIURPLQWHULRURIKRRGERG\

attaching single blower plate to top of hood

body. Remove single blower and single blower

plate.

3. Knock out rear plate B for rear rectangular rear

ducting or plate C for 8 inch round rear ducting.

C

This range hood is equipped standard with a 8” round vertical duct option. To convert from 8” round vertical to 8”

round horizontal ducting or 3-1/4” x 10” rectangular horizontal ducting please following the instructions below.

VERTICAL TO HORIZONTAL DUCTING CONVERSION

Installation – Single Blower Horizontal Ducting Conversion

B

 5HPRYHVFUHZVDWWDFKLQJEORZHUWREORZHU

plate. Turn blower 180 degrees and reattach to

blower plate.

12

www.zephyronline.com

6. Attach 8” round duct collar or 3 1/4”x10”

rectangular duct collar to back of hood body

XVLQJ0[VFUHZV

7. From inside hood body, position top cover plate

to top of hood body. From outside hood body,

attach top cover plate to top of hood body using

[VFUHZV

8. Connect blower plug.

Installation – Single Blower Horizontal Ducting Conversion

5. Position single blower with single blower plate

as shown. Be sure to tuck back of single blower

plate into tabs at back of hood. Secure single

EORZHUSODWHWREDFNRIKRRGXVLQJVFUHZV

removed from step 2.

13

Installation – PBD-1200A Dual Blower Vertical Ducting

1. Disconnect blower plug.

 5HPRYHVFUHZVIURPLQWHULRURIKRRGERG\

attaching single blower plate to top of hood

body. Remove single blower and single blower

plate.

 5HPRYHVFUHZVDWWDFKLQJVLQJOHEORZHUWR

single blower plate.

 $WWDFKVLQJOHEORZHUWRGXDOEORZHUSODWHE\

previously removed screws from step 3.

This range hood is equipped standard with a single blower vertical duct option. To convert from single blower

vertical ducting to dual blower vertical ducting please following the instructions below.

5. Position dual blower inside hood body as

shown. Be sure to tuck dual blower plate into

EORZHUSODWHWDEV6HFXUHGXDOEORZHUE\

screws previously removed from step 2.

6. Attach 10” round blower collar to top of hood

ERG\E\0[VFUHZV&RQQHFWEORZHU

wire extension cable to new blower and connect

plugs from each blower to female plugs behind

switch panel.

14

www.zephyronline.com

5. Knock out plate A for dual blower horizontal

ducting.

6. Position dual blower inside hood body. Attach by

VFUHZVSUHYLRXVO\UHPRYHGIURPVWHS

7. From inside hood body, position top cover plate

to top of hood body. From outisde hood body,

attach top cover plate to top of hood body using

[VFUHZV

8. Attach 10 inch round blower collar to back of

KRRGXVLQJ0[VFUHZV&RQQHFWEORZHU

wire extension cable to new blower and connect

both plugs from each blower to female plugs

behind switch panel.

A

Installation – PBD-1200A Dual Blower Horizontal Ducting

Follow Steps 1 through 4 on page 13, then continue PBD-1200A horiztantal ducting installation by following the

steps below.

15

Lights On/Dim/Off

5 Min Delay Off

Display (speed level, delay off, filter clean)

Adjust 6 Speed Levels

Blower On/Off

1. Blower On/Off

By pressing the blower is switched on and off. When switched on, the blower starts up on speed level 1.

ACT Verification

- Airflow Control Technology (ACT) allows the installer to set the maximum blower CFM to align with local codes and regulations.

- To verify the maximum blower CFM:

- With hood off, hold the button for 3-4 seconds. If number 6 displays = default max. CFM, if number 3 displays = max.

390 CFM, and if number 2 displays = max. 290 CFM.

2. Speed Selection

The 6 speed levels are selected by pressing to decrease and to increase speed levels. The display indicates levels

selected.

ACT Enabled Speed Selections

- When ACT is enabled, the number of blower speeds will be reduced as follows:

- 390 CFM = Maximum 3 speeds

- 290 CFM = Maximum 2 speeds

3. Delay Off

This feature is used for programmed shut down of blower 5 minutes after the function is activated. Press once, a dot flashes

in the lower right side of display indicating the function is on. The blower will completely shut down after 5 minutes.

4. Lights On/Dim/Off

Switch lights on by pressing once, press a second time to dim and again to shut off lights.

5. Display Window

The display window indicates speed levels and features such as baffle filter clean reminder, delay off and clean air indicator.

Features & Controls – Touch Controls

16

www.zephyronline.com

Features & Controls – Touch Controls

Charcoal Filter Change Reminder (charcoal filter, if installed)

When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust

and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to

be replaced after every 120 hours of use. The charcoal filters should never be cleaned or placed in a dish

washer.

The filter change reminder function in the microprocessor needs to be switched on. When switched on, the

microprocessor will elapse and count usage time and indicate by a flashing when charcoal filter

replacements are needed.

C

Setting the Filter Change Reminder

When off, hold for approximately 5 seconds.

The display will change from (exhaust mode) to

(recirculating mode) this indicates that the

elapse timer function is switched on and charcoal

filters are used.

Filter Replace Indicator

When the display starts flashing, the charcoal

filters need to be replaced.

Re-setting Function

Once filters are replaced, with hood off, press and

hold the display will appear; hold for apprimately

5 seconds until on displays disappears .

The filter change reminder is now re-set and a new

120 hour elapse cycle is initiated.

C

hold 5 sec. display from < - > to < C >

Set Mode

display < C > flashes

Change FIlters

C

hold 5 sec. display from < C > to < >

To Reset

C

17

Baffle Filter Clean Reminder

Aa set of baffle filters are fitted by the factory, these baffle filters are intended to filter out residue from

cooking. The filters need not be replaced on a regular basis but are required to be kept clean. The Baffle-

Filter Clean reminder function in the microprocessor will automatically indicate by a flashing when the

baffle filters need to be cleaned after every 30 hours of use. Filters can be cleaned by hand with non-

abrasive soap or in a dishwasher. Heavily soiled filters should also be soaked in grease cutting detergent

prior to cleaning.

Baffle Filter Clean Indicator

When flashes on the display, the baffle filters

needo be cleaned. This will occur after every 30

hours of use.

Reset the filter clean reminder timer after filters are

cleaned and re-installed. With hood off, press and

hold for approximately 5 seconds until on

display disappears . The filter clean reminder

function is now reset and a new 30 hours elapse

cycle is initiated.

F

Clean Filters

display < F > flashes

F

hold 5 sec. display from < F > to < >

To Reset

F

A

hold 3 sec. display from < A > to < >

To Disable

hold 3 sec.

To Enable

F

display < A > flashes

A

A 1 A 1

Clean Air Indicator

While Clean Air is active, the display will alternate

between , , , .

A

fter 10 minutes of Clean Air operation, the blower

will power off and the 4 hour timer will reset.

If the blower speed is changed while the Clean Air

Function is in use, the cycle will be interrupted and

the timer will reset after.

Clean Air Function

Clean Air is a feature that turns on the blower on low speed every 4 hours for 10 minutes to remove stagnant

air in the kitchen. The Clean Air function is disabled by default and must be enabled by the user.

and

Features & Controls – Touch Controls

18

www.zephyronline.com

RF REMOTE MAINTENANCE:

Clean the remote control using non abrasive detergents

Follow instructions below for replacing battery.

8VLQJDVPDOOÀDWKHDGVFUHZGULYHUUDLVHWKHFRYHURIWKHEDWWHU\

GRRUALQRUGHUWRDFFHVVWKHEDWWHU\FRPSDUWPHQW),*

Remove the battery and replace with battery type A23 12V.

Negative end of battery should face the spring inside the remote.

Re-install battery door and recycle old battery.

RF REMOTE FEATURES:

The RF remote control is equipped with a magnet on the back for easy

storage. The remote may be placed on any magnetic surface such as a

refrigerator or the Zephyr remote holder, FIG. 1. The remote holder can

be inserted into a standard electrical outlet for easy storage. Note: The

remote holder does not charge the RF remote.

Maximum remote control communication distance is 15 feet from the hood.

SYNCHRONIZATION: To create a unique link between your hood and remote control please follow these steps:

1. With hood off, press and hold the “lights” button on the hood until the letter “F” shows on the display screen.

2. Press the “lights” button on the remote, the lights on the hood will turn on and synchronization is complete.

RF REMOTE FUNCTIONS:

FIG. 1

FIG. 2

Blower On / Speed Selection

Press to power on blower and cycle through all six blower speeds.

Blower On / Power Off

By pressing , the blowers will power on at the last speed setting. Press

again and the entire hood will power off, including lights.

Delay Off

Lights On / Dim / Off

Switch lights On by pressing once, again to dim and again to switch Off.

Blower On/

Speed Selection

1

2

3

4

Blower On/

Power Off

2

5 Min Delay Off

3

Lights On/Dim/Off

4

By pressing , the blower and lights will enter Delay Off mode. A dot will

appear in the lower right corner of the hood display indicating the function

is on. The blower will change to speed 1 and shut down after 5 minutes.

A

-

+

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compli-

ance could void the user’s authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer

or peripheral device. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) This device

may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause

undesired operation.

THE RF REMOVE CONTROL IS AN OPTIONAL

ACCESSORY NOT INCLUDED WITH THE HOOD AND

MUST BE PURCHASED SEPARATELY

Features & Controls – Optional Remote Control

La page charge ...

Zephyr AK7500BS Hood User Manual

Zephyr AK7500BS Hood User Manual

dans d''autres langues

Documents connexes