Shure BLX288 Mode d'emploi

Marque: Shure

Modèle: BLX288

Catégorie: Équipement musical supplémentaire

Taper: Mode d'emploi

BLX

Wireless System

Online user guide for Shure BLX wireless system.

Version: 5.3 (2022-E)

Shure Incorporated
2/23
Table of Contents
BLX   Wireless System                                                        3
System Components                                                           3
Quick Start Guide                                                                 3
Features                                                                                5
Front Panel                                                                        5
Back Panel                                                                         6
BLX1                                                                                  6
BLX2                                                                                  7
Single System Set Up                                                          8
Setting Transmitter Group and Channel                            9
Group (letter)                                                                      9
Channel (number)                                                              9
Multiple System Setup                                                       10
Manually Setting Receiver Group and Channel              10
Group (letter)                                                                    10
Channel (number)                                                            10
Locking and Unlocking Controls                                      10
Transmitter (lock/unlock)                                                   11
Receiver (lock/unlock)                                                       11
Tips to Improve Wireless System Performance             11
Getting Good Sound                                                          11
Correct Microphone Placement                                       12
Wearing the Headworn Microphone                                12
Adjusting Gain                                                                   12
BLX1                                                                                13
BLX2                                                                                13
Batteries                                                                              13
Wearing the Bodypack Transmitter                                  14
Power Off                                                                            14
Removing and Installing Identification Caps                  15
Troubleshooting                                                                 15
Frequency Range and Transmitter Output Level            16
Specifications                                                                     17
IMPORTANT SAFETY INSTRUCTIONS                             20
Certifications                                                                      21
Important Product Information                                         22
LICENSING INFORMATION                                            22
Information to the user                                                     22
Australia Warning for Wireless                                         23

Shure Incorporated

3/23

•

1. 1.

BLX 

Wireless System

System Components

Note: Your system comes with a combination of the following components.

BLX1 Bodypack Transmitter

BLX2 Handheld Transmitter (choice of SM58, BETA58A, or PG58)

BLX4 Wireless Receiver

BLX88 Dual Wireless Receiver

PS24 Power Supply

Lavalier microphone (choice of CVL, WL185 or WL93)

Headworn microphone (choice of PGA31, SM31FH or SM35)

MX153 Earset microphone

Instrument microphone (BETA98H/C)

Guitar cable (WA302)

Quick Start Guide

Connect receiver to power source.

Connect receiver to mixer or amplifier. Hold power button to turn on.

Press group button on receiver to perform a group scan.

Shure Incorporated

4/23

3. 1.

Install batteries and turn on transmitter.

Onthetransmitter,setthegroupandchanneltomatchthereceiver.TheaudioLEDonthereceivershouldillu

minate.

Ifsettingupadditionalsystems,leavethefirsttransmitterandreceiveron.Foreachadditionalreceiver,manual

lysetthegrouptomatchthefirstreceiver.Note:Thereceiverwillautomaticallyperformachannelscantofind

an available frequency after the group has been selected. Set the transmitter frequency to match the receiver.

If sound is too faint or distorted, adjust the gain accordingly.

Shure Incorporated

5/23

Features

Front Panel

BLX4

BLX88

① audio LED

Indicates strength of incoming audio signal: green for normal and red for overload.

② ready LED

Green light indicates system is ready for use and receiving transmitter signal.

③ LED Display

Shure Incorporated

6/23

Displays group and channel setting.

④ group and channel Buttons

Scan: Push and release group button to scan for an open group and channel.

Manual: Push and hold group button to select a group. Push channel button to select a channel in the current group.

⑤ power Button

Push and hold to turn power on or off.

Back Panel

BLX4

BLX88

① DC Power Jack

② Adapter Cord Tie-Off

③ XLR microphone output jack (MIC out)

④ 6.35 mm (1/4") instrument level output jack (instrument out)

BLX1

① LED Indicator

Displays power and battery status (see Transmitter LED Indicators).

② power Switch

Toggles power on or off.

③ 4-Pin Microphone Input Jack (TA4 connector)

Shure Incorporated

7/23

④ Antenna

⑤ group Button

Changes group setting.

⑥ LED Display

Displays group and channel setting.

⑦ channel Button

Changes channel setting.

⑧ Battery Compartment

⑨ Audio Gain Adjustment

Rotate to increase or decrease transmitter gain.

BLX2

① LED Indicator

Displays power and battery status (see Transmitter LED Indicators).

② power Button

Push to turn power on or off.

③ group Button

Changes group setting.

④ channel Button

Changes channel and gain setting.

⑤ LED Display

Shure Incorporated

8/23

Displays group and channel setting.

⑥ Identification Cap

⑦ Battery Compartment

Transmitter LED Indicators

LED Indicator Status

Green Ready

Rapidly Flashing Red Controls locked

Solid Red Battery power low (less than 1 hour remaining*)

Flashing Red and shuts off Batteries dead (change batteries to power on transmitter)

*For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.

Single System Set Up

Shure Incorporated

9/23

•

Before you begin, turn off all transmitters and turn on any equipment (other microphones or personal monitoring systems) that

could cause interference during the performance.

Press and release the group button on the receiver.

The receiver scans for the clearest group and channel.

Note: If you want to stop the scan, push the group button again.

Turn on transmitter and change the group and channel to match the receiver (See SettingTransmitterGroupandChan

nel).

Once the system is set up, perform an audio check and adjust the gain if necessary.

Setting Transmitter Group and Channel

Transmitter group and channel must be manually set to match the receiver.

Group (letter)

Press and release the group button on the transmitter to activate the display. Press the groupbuttonagainandthedis

play flashes.

While the display is flashing, press the group button again to advance to the desired group setting.

Channel (number)

If channel needs to be changed, follow the same procedure using the channel button instead of the group button.

Note:

When the group and channel correctly match the receiver, the ready LED on receiver illuminates.

After manual setup, the transmitter alternately displays the group and channel setting for about two seconds.

Shure Incorporated

10/23

Multiple System Setup

Up to 12 systems can operate simultaneously (band and RF environment dependent).

Important: Set up each system one-at-a-time. Once a receiver and transmitter are tuned to the same group and channel, leave the transmitter powered on.

Otherwise, scans from the other receivers will not detect that channel as occupied. For the BLX88, be sure to setup both transmitters before progressing to the

next receiver.

Turn on any other equipment that could cause interference during the performance so it will be detected during the group and channel scans in the following

steps.

Before you begin system set up, turn all receivers ON and all transmitters OFF.

For the first receiver:

Perform a group scan.

This finds the group with the most clear channels.

Note: For the BLX88, the group scan sets up both receivers at the same time.

Turn on the first transmitter and change the group and channel to match receiver.

Leave the transmitter on and continue with the additional systems.

Note: If the selected group does not contain enough open channels, manually select group "d" when setting up larger systems.

For each additional receiver:

Use manual setup to change the receiver to match the group setting of the first receiver. Recall that each time the

group setting is changed, a channel scan is automatically done.

Turn on the transmitter and change the group and channel to match the receiver.

Leave the transmitter on and continue to the next system.

Once all receivers are set up, perform an audio check on all microphones.

Manually Setting Receiver Group and Channel

The receiver group may need to be changed as part of a multiple system setup.

Group (letter)

Hold the group button on the receiver until the display begins to flash.

While the display is flashing, press the group button again to advance to the next group.

Note: Only the group setting will be displayed during the manual setup.

Once the desired group is reached, release the group button. The receiver automatically performs a channel scan.

Channel (number)

Always use a channel selected by the channel scan. However, if necessary, the channel can be set manually. Follow the same

steps above using the channel button instead of the group button.

Shure Incorporated

11/23

•

Locking and Unlocking Controls

Lock system controls to prevent accidental setting changes or power off.

Transmitter (lock/unlock)

Turn the transmitter on. Hold the group button, then press the channel button for approximately 2 seconds. The LED indicator

rapidly flashes red when locked.

Receiver (lock/unlock)

Turn the receiver on. Simultaneously hold the group and channel button. The display flashes rapidly.

When locked, the display flashes rapidly if any key is pressed.

The BLX88 locks on both sides when locked from either side.

Tips to Improve Wireless System Performance

If you encounter interference or dropouts, try the following suggestions:

Choose a different receiver channel

Reposition the receiver so there is nothing obstructing a line of sight to the transmitter (including the audience)

Avoid placing transmitter and receiver where metal or other dense materials may be present

Move the receiver to the top of the equipment rack

Remove nearby sources of wireless interference, such as cell phones, two-way radios, computers, media players, Wi-Fi

devices, and digital signal processors

Charge or replace the transmitter battery

Keep transmitters more than two meters (6 feet) apart

Keep the transmitter and receiver more than 5 meters (16 feet) apart

During sound check, mark trouble spots and ask presenters or performers to avoid those areas

Shure Incorporated

12/23

•

Getting Good Sound

Correct Microphone Placement

Holdthemicrophonewithin12inchesfromthesoundsource.Forawarmersoundwithincreasedbasspresence,move

the microphone closer.

Do not cover grille with hand.

Wearing the Headworn Microphone

Positiontheheadwornmicrophone13mm(1/2in.)fromthecornerofyourmouth.

Positionlavalierandheadwornmicrophonessothatclothing,jewelry,orotheritemsdonotbumporrubagainstthemicro

phone.

Shure Incorporated

13/23

•

Adjusting Gain

Monitor the audio LED indicator on the receiver front panel when setting the transmitter gain.

Green: normal levels

Red: excessive sound levels (overload).

The red LED should only illuminate infrequently when you speak loudly or play your instrument loudly.

BLX1

Rotatetheaudiogainadjustmenttoincrease(+)ordecrease(−)thegainuntildesiredlevelisreached.

For instruments, turn gain to minimum setting. For lavaliers, increase the gain as desired.

BLX2

The BLX2 features two gain level settings, default and attenuated (-10 dB). The default setting is used for most situations. If the

receiver audio LED flickers red often, set the microphone to attenuated. Use the channel button to change the gain setting.

Hold down the channel button for 5 seconds.

AdotappearsonthelowerrighthandcorneroftheLEDdisplay,whichindicates−10dBgainsettinghasbeenactivat

ed.

To change the gain back to default, hold the channel button again for 5 seconds, or until the dot disappears.

Shure Incorporated

14/23

Batteries

Expected life for AA batteries is up to 14 hours (total battery life varies depending upon battery type and manufacturer).

When the LED indicator turns red, it signifies "low battery" with approximately 60 minutes of remaining battery life.

For alkaline batteries only. For rechargeable batteries, solid red means the batteries are dead.

To remove batteries from the handheld transmitter, push them out through the opening in the microphone battery compartment.

WARNING: Battery packs shall not be exposed to excessive heat such as sunshine, fire, or the like.

Wearing the Bodypack Transmitter

Clip the transmitter to a belt or slide a guitar strap through the transmitter clip as shown.

For best results, the belt should be pressed against the base of the clip.

Shure Incorporated

15/23

Power Off

Hold down the power button to power off the BLX2 or BLX4/88. To power off the BLX1, slide the power toggle switch to OFF.

Removing and Installing Identification Caps

The BLX2 is equipped with a black identification cap from the factory (dual vocal systems ship with additional gray cap).

To remove: Remove battery cover. Squeeze sides and pull off cap.

To install: Align the cap and click into place. Replace battery cover.

An Identification Cap Kit containing assorted colored caps is available as an optional accessory.

Troubleshooting

Issue Indicator Status Solution

No sound or faint sound

Receiver ready LED on

Verify all sound system connections or adjust gain as

needed (see Adjusting Gain)

Verify that the receiver is connected to mixer/amplifier

Receiver ready LED off

Turn on transmitter

Make sure the batteries are installed correctly

Perform transmitter setup (see Single System Setup)

Insert fresh batteries

Receiver LED screen off

Make sure DC adapter is securely plugged into electrical

outlet.

Make sure receiver is powered on.

Shure Incorporated

16/23

Issue Indicator Status Solution

Transmitter indicator LED

flashing red Replace transmitter batteries (see Changing Batteries).

Audio artifacts or dropouts Ready LED flickering or off

Change receiver and transmitter to a different group and/

or channel.

IdentifynearbysourcesofRFinterference,andshut

down or remove source.

Replace transmitter batteries.

Ensurethatreceiverandtransmitterarepositionedwith

in system parameters

System must be set up within recommended range and

receiver kept away from metallic surfaces.

Transmitter must be used in line of sight from receiver for

optimal sound

Distortion AudioLEDonreceiverindi

cates overload (red) Reduce transmitter gain (see Adjusting Gain).

Sound level variations when

switching to different

sources

N/A Adjust transmitter gain as necessary (see Adjusting

Gain).

Receiver/transmitter won't

turn off LED/display flashing rapidly See Locking and Unlocking Controls.

Frequency Range and Transmitter Output Level

Band Range Output Power

G18 470 to 494 MHz 10 mW

H8 518 to 542 MHz 10 mW

H8E 518 to 542 MHz 10 mW

H9 512 to 542 MHz 10 mW

H10 542 to 572 MHz 10 mW

H10E 542 to 572 MHz 10 mW

H11 572 to 596 MHz 10 mW

H62 518 to 530 MHz 10 mW

J10 584 to 608 MHz 10 mW

J11 596 to 616 MHz 10 mW

K3E 606 to 630 MHz 10 mW

Shure Incorporated

17/23

Band Range Output Power

K12 614 to 638 MHz 10 mW

K14 614 to 638 MHz 10 mW

L27 674 to 698 MHz 10 mW

M15 662 to 686 MHz 10 mW

M17 662 to 686 MHz 10 mW

M18 694 to 703 MHz 10 mW

M19 694 to 703 10 mW

Q12 748 to 758 10 mW

Q24 748 to 758 MHz 10 mW

Q25 742 to 766 MHz 10 mW

R12 794 to 806 MHz 10 mW

S8 823 to 832 MHz 10 mW

T11 863 to 865 MHz 10 mW

Note: Frequency bands might not be available for sale or authorized for use in all countries or regions.

NOTE: ThisRadioequipmentisintendedforuseinmusicalprofessionalentertainmentandsimilarapplications.ThisRadioapparatusmaybecapableofoper

ating on some frequencies not authorized in your region. Please contact your national authority to obtain information on authorized frequencies and RF power

levels for wireless microphone products.

เครื่องโทรคมนาคมและอุปกรณ์นี้มีความสอดคล้องตามมาตรฐานหรือข้อกำหนดทางเทคนิคของ กสทช.

Specifications

System

Working Range

91m(300ft)LineofSight

Note: Actual range depends on RF signal absorption, reflection and interference.

Audio Frequency Response

50to15,000Hz

Note: Dependent on microphone type

Total Harmonic Distortion

Ref. ±33 kHz deviation with 1 kHz tone

0.5%, typical

Shure Incorporated

18/23

Dynamic Range

100dB,Aweighted,typical

Operating Temperature

-18°C (0°F) to 57°C (135°F)

Note: Battery characteristics may limit this range.

Polarity

Positivepressureonmicrophonediaphragm(orpositivevoltageappliedtotipofWA302phoneplug)pro

ducespositivevoltageonpin2(withrespecttopin3oflowimpedanceoutput)andthetipofthehighim

pedance 1/4-inch output.

BLX1

Audio Input Level

max 16dBVmaximum

min (0 dB) +10dBVmaximum

Gain Adjustment Range

26dB

Input Impedance

1MΩ

RF Transmitter Output

10mW,typical

varies by region

Dimensions

4.33in.X2.52in.X0.83in.(110mmX64mmX21mm)HxWxD

Weight

2.6oz.(75g),withoutbatteries

Housing

Molded ABS

Power Requirements

2LR6AAbatteries,1.5V,alkaline

Battery Life

upto14hours(alkaline)

Shure Incorporated

19/23

BLX2

Audio Input Level

0dB 20dBVmaximum

-10dB 10dBVmaximum

Gain Adjustment Range

10dB

RF Transmitter Output

10mW,typical

varies by region

Dimensions

8.82in.X2.09in.(224mmX53mm)LxDia.

Weight

7.7oz.(218g)withoutbatteries

Housing

Molded ABS

Power Requirements

2LR6AAbatteries,1.5V,alkaline

Battery Life

upto14hours(alkaline)

BLX4

Output Impedance

XLR connector 200Ω

6.35 mm (1/4") connector 50Ω

Audio Output Level

Ref. ±33 kHz deviation with 1 kHz tone

XLR connector –27dBV(into100kΩload)

6.35 mm (1/4") connector –13dBV(into100kΩload)

RF Sensitivity

105dBmfor12dBSINAD,typical

Image Rejection

>50dB,typical

Shure Incorporated

20/23

Dimensions

1.57in.X7.40in.X4.06in.(40mmX188mmX103mm)HxWxD

Weight

8.5oz.(241g)

Housing

Molded ABS

Power Requirements

12–15VDC@235mA(BLX88,320mA),suppliedbyexternalpowersupply(tippositive)

BLX88

Output Impedance

XLR connector 200Ω

6.35 mm (1/4") connector 50Ω

Audio Output Level

Ref. ±33 kHz deviation with 1 kHz tone

XLR connector –27dBV(into100kΩload)

6.35 mm (1/4") connector –13dBV(into100kΩload)

RF Sensitivity

105dBmfor12dBSINAD,typical

Image Rejection

>50dB,typical

Dimensions

1.50in.X12.13in.X3.98in.(38mmX308mmX101mm)HxWxD

Weight

15.1oz.(429g)

Housing

Molded ABS

Power Requirements

12–15VDC@235mA(BLX88,320mA),suppliedbyexternalpowersupply(tippositive)

IMPORTANT SAFETY INSTRUCTIONS

READ these instructions.

KEEP these instructions.

HEED all warnings.

La page charge ...

Shure BLX288 Mode d'emploi

Marque: Shure

Modèle: BLX288

Catégorie: Équipement musical supplémentaire

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Shure BLX288 User guide

Shure BLX288 Mode d'emploi

Shure BLX288 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents