EZVIZ CSC1C Manuel utilisateur

Marque: EZVIZ

Modèle: CSC1C

Taper: Manuel utilisateur

Box Content

Internet Camera (x1) USB Cable (x1) Power Adapter (x1)

Foam Sticker (x2) Metal Plate (x1)

(3.5mm Hole Diameter)

Regulatory Information

(x1) Quick Start Guide (x1)

The camera appearance is subject to the actual one you have bought.

Basics

MIC

Lens

LED Indicator

Magnetic Base

Speaker

Power Input

microSD Card

Slot

RESET Button

Name Description

LED Indicator • Solid Red: Camera is starting up.

• Slow-ashingRed:Wi-Ficonnectionhasfailed.

• Fast-ashing Red: Device exception (e.g. microSD card error).

• Solid Blue: Video is being viewed or played back in EZVIZ App.

• Fast-ashing Blue:CameraisreadyfortheWi-Ficonnection.

• Slow-ashing Blue: Camera is running properly.

microSD Card • microSD Card should be purchased separately.

• Initialize the card in the EZVIZ app before using it.

RESET Button Hold down the RESET button for 5 seconds while the camera is running, the

camera restarts and all parameters are reset to default.

Setup

Step 1 Power-on

Plug the power cable into the camera and to the power adapter and then into a

poweroutlet,asshowninthegurebelow.

Power Outlet

Power Cable

Step 2 Camera Setup

1. Create a user account

-ConnectyourmobilephonetoWi-Fi.

-Download and install the EZVIZ app by searching “EZVIZ” in App Store or Google

PlayTM.

-Launch the app and register for an EZVIZ user account following the start-up

wizard.

2. Add a camera to EZVIZ

-Log in the EZVIZ app.

-From the EZVIZ app Home screen, tap “+” on the upper-right hand corner to go to

the scan QR code interface.

-Scan the QR Code on the bottom of the camera.

Bottom of the Camera

-FollowtheEZVIZappwizardtonishWi-Ficonguration.

Pleasemakesureyourphoneisconnectedtothe2.4GHzWi-Fifromtherouter

forWi-Ficonguration.

Installation

Step 1 Install the Metal Plate (Optional)

Pickacleanandatsurfaceandsecurethemetalplatetothedesiredpositionwith

the foam stickers or screws (not included).

There’s a magnet piece inside the camera. You can skip this step if the surface

is made of metal.

Step 2 Install the Camera

Secure the camera magnetically to the metal plate or metal surface (see figure

below).

Foam Sticker

Metal Plate

Step 3 Complete Installation

Adjust the camera angle as required.

Appendix

Step 1 Install Memory Card

Insert a microSD card into the slot until a click.

Step 2 Initializing Memory Card

1. In the EZVIZ app, check the memory card status by tapping on the Storage Status

in the Device Settings interface.

2. If the memory card status displays as Uninitialized, tap to initialize it. The status

will then change to Normal.

For detailed information, please visit www.ezvizlife.com.

Regulatory Information

EC DECLARATION OF CONFORMITY

Hereby, Hangzhou EZVIZ Software Co., Ltd. declares that the radio equipment type [CS-C1C, CS-C1HC, CS-C1T, CS-C2C,

CS-CV206, CS-CV310, CS-C3N, CS-C3W, CS-C3WN, CS-C3X, CS-C6N, CS-CV246, CS-CV248, CS-C6CN, CS-C6C, CS-C6W,

CS-TY1, CS-TY2, CS-TY3, CS-CV336, CS-DP1, CS-DP1C, CS-DP2C, CS-DB2C, CS-C4W, CS-C4C, CS-CV228, CS-C5W, CS-C5C,

CS-C5HC, CS-C5X, CS-C5HX, CS-C8W, CS-C8C, CS-C3A, CS-BC1, CS-W2H, CS-X5S-4W, CS-X5S-8W, CS-A1-32W, CS-T9-A,

CS-T4-A] is in compliance with Directive 2014/53/EU.

The full text of the EC DECLARATION OF CONFORMITY is available at the following web link:

http://www.ezvizlife.com/declaration-of-conformity.

This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore

with the applicable harmonized European standards listed under the Radio Equipment Directive

2014/53/EU, the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted

municipal waste in the European Union. For proper recycling, return this product to your local supplier upon

the purchase of equivalent new equipment, or dispose of it at designated collection points. For more

information see: www.recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that

cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation

for specific battery information. The battery is marked with this symbol, which may include lettering to

indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier

or to a designated collection point. For more information see: www.recyclethis.info

Use only power supplies listed in the Table.

Equipment model Adapter manufacture Adapter model

CS-C1C/ CS-C1HC/ CS-C1T/ CS-C2C/

CS-CV206/ CS-CV246/ CS-C6N/

CS-C6CN/ CS-C6C/ CS-TY1/ CS-TY2/

CS-TY3/ CS-W2D/ CS-A1-32W/

CS-T9-A

Shenzhen Honor Electronic Co Ltd ADS-5RE-06 05050EPCU/EPC(US),

ADS-5RH-06 05050EPB(UK),

ADS-5RH-06 05050EPG(EU),

ADS-5RH-06 05050EPSA(AU),

ADS-5RH-06 05050EPBR(BR),

ADS-5RH-06 05050EPI(IN),

ADS-5MA-06A 05050GPK(KR)

CS-CV248/ CS-C6W/ CS-C6Wi/

CS-CV336/ CS-DP1/ CS-DP1C/

CS-DP2C/ CS-C3A/ CS-BC1

Shenzhen Honor Electronic Co Ltd ADS-10LA-06 05010EPCU/EPC(US),

ADS-10RH-06 05010EPB (UK),

ADS-10RH-06 05010EPG(EU),

ADS-10RH-06 05010EPSA(SA),

ADS-10RH-06 05010EPBR(BR),

ADS-10RH-06 05010EPI(IN),

ADS-12CG-06 05010EPC(JP)

CS-CV310/ CS-C3N/ CS-C3W/

CS-C3WN/ CS-C3X/ CS-SD1/

CS-C4W/ CS-C4C/ CS-CV228/

CS-C8W/ CS-C8C/ CS-W2H/

CS-W3C-WD1200G/ CS-T8-B

Shenzhen Honor Electronic Co Ltd ADS-12FG-12N 12012EPCU(US),

ADS-12FG-12N 12012EPB(UK),

ADS-12FG-12N 12012EPG(EU),

ADS-12FB-12 12012EPSA(AU),

ADS-12FG-12N 12012EPBR(BR),

ADS-12FG-12N 12012EPI(IN)

Moso Power Supply Technology Co. Ltd MSA-C1500IC12.0-18P-GB(UK),

MSA-C1500IC12.0-18P-DE,

MSA-C1500IC12.0-18P-AU(AU),

MSA-C1500IC12.0-18P-BR(BR),

ADS-25FSG-12 12018GPI(IN)

CS-X5S-4W/ CS-X5S-8W

Important Safety Information

Note: Please read the manual before using the device.

Caution: Do not block ventilation openings while the system is on, and keep at least 2 cm distance from

ventilation openings and walls or other things which may block the openings.

Warning: Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery that

can result in an explosion.

Warning: Leaving a battery in an extremely high temperature surrounding environment that can result in an

explosion or the leakage of flammable liquid or gas.

Warning: A battery subjected to extremely low air pressure that may result in an explosion or the leakage

of flammable liquid or gas.

Warning: Dispose of used batteries according to the instructions.

Warning: Replace only with the same or equivalent type recommended by the manufacturer.

Caution: THE PRODUCT IS BUILT IN A REPLACEABLE BATTERY.

Warning: Do not ingest battery, Chemical Burn Hazard.

Caution: This product contains a coin/button cell battery. If the coin / button cell battery is swallowed, it

can cause severe internal burns in just 2 hours and can lead to death.

Caution: Keep new and used batteries away from children.

Caution: If the battery compartment does not close securely, stop using the product and keep it away from

children.

Caution: If you think batteries might have been swallowed or placed inside any part of the body, seek

immediate medical attention.

Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.

Caution: This symbol on the device indicates that the safety compatibility manual and / or installation

manual must be read, which contains information related to the safe operation of the device. Be sure to

read these instructions before operating the equipment.

Warning: The separate earthing terminal must be permanently connected to earth.

Warning: For SELV DC input: the DC power source shall comply with the Safety Extra-Low Voltage (SELV)

requirements of IEC 60950-1.

FCC Information

Please take attention that changes or modification not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

FCC compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following measures:

—Reorient or relocate the receiving antenna.

—Increase the separation between the equipment and receiver.

—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

—Consult the dealer or an experienced radio/TV technician for help.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

FCC Conditions

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired operation.

Industry Canada ICES-003 Compliance

This device meets the CAN ICES-3 (B)/NMB-3(B) standards requirements.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two

conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or

lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the

antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than

that necessary for successful communication.

This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radioexempts de licence.

L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en

compromettre le fonctionnement.

Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut

fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie

Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir

le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité

nécessaire à l'établissement d'une communication satisfaisante.

Cet équipement doit être installé et utilisé à une distance minimale de 20 cm entre le radiateur et votre corps.

IFETEL Information

La operación de este equipo está sujeta a las siguientes dos condiciones:

(1) es posible que este equipo o dispositivo no cause interferencia perjudicialy

(2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no

deseada.

102026549，B

EZVIZ CSC1C Manuel utilisateur

Marque: EZVIZ

Modèle: CSC1C

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: EZVIZ CSC1C User manual

Documents connexes

Autres documents

Hikvision DS-7632NI-I2 Manuel utilisateur