Chief SLMU Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
Ce manuel convient également à
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
SLBU SLMU
Universal Interface Brackets
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SLBU/SLMU
SLBU/SLMU Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the SLBU-SLMU interface
brackets does not exceed 50 lbs (22.68 kg).
DIMENSIONS
3.49
88.6
3.66
93
4.69
119
6.66
169.07
R7.49
190.2
Ø 3.75
BOLT CIRCLE
95.2
4X 32.5°
4X 7.5°
1.06
26.97
4X Ø .27
6.7
1 1/2"
NPT
5.66
143.7
3.25
82.6
(SLBU with RMA shown)
Installation Instructions SLBU/SLMU
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Socket Wrench
Llave de cubo
Llave de cubo
Chave de caixa
Chiave a brugola
Dopsleutel
Clé à douilles
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
SLBU/SLMU Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/4" (included)
5/32" (security - included)
B (4)
OR
A (1)
[SLBU Plate] A (1)
[SLMU Plate] [SLBU/SLMU Leg]
C (2)
[Security Cover Bracket]
[SLBU Only] D (4)
[Thumb Nut]
[SLBU Only]
5/32" (security)
J (1)
G (4)
10-24 x 3/8"
[All Points Security Kit]
H (1)
5/16-18 x 1/2"
[SLBU Only] [SLBU Only]
N (4)
M (4)
M2.5 x 10mm M3 x 10mm
L (4)
8-32 x 1/4"
R (4)
M6 x 12mm
P (4)
M4 x 10mm Q (4)
M5 x 12mm
1/4"
T (4)
S (4)
M4 1/4-20 U (1) 5/32"
V (1)
(security)
[Universal Projector Interface Hardware Kit]
[Universal Hardware Kit - Long Screws]
W (4)
M3 x 25mm X (4)
M4 x 25mm Y (4)
M5 x 25mm
Z (4)
M6 x 25mm AA (4)
.500 x .257 x .625
K (4)
8-32 x 3/8"
[SLBU Only]
E (2)
10-24 x 3/8"
[SLBU Only]
[No hardware
designated "F"]
Installation Instructions SLBU/SLMU
5
ASSEMBLY AND INSTALLATION
Remove Screw Adapters from SLBU/SLMU Legs
1. Press locking buttons on SLBU/SLMU leg (B) firmly and
simultaneously push clip cover toward enclosed sliding stud
mount bracket and screw. (See Figure 1)
2. Screw adapter and attached height-adjustment nut will be
released. Set aside for later use. (See Figure 1)
3. Repeat Steps 1-2 for each leg to be used in installation.
Figure 1
Attach Projector to SLBU/SLMU
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components attached to the SLBU-SLMU interface
brackets does not exceed 50 lbs (22.68 kg).
1. Determine proper size screw to insert into projector. Test
Phillips screws (M, N, P, Q and R) provided until one fits the
projector holes.
2. Insert screws through M4 flat washers (S), screw adapters
with height-adjustable nuts and into projector holes. (See
Figure 2)
NOTE: Only use washers (S) if using M or N screws to attach
screw adapters to projector.
Figure 2
3. Adjust height-adjustment nuts to desired level. (See
Figure 3)
NOTE: Height-adjustment nuts should be adjusted as low as
possible while ensuring that the legs will always clear
any elevated surfaces on the projector. All nuts must be
adjusted to the same level to ensure an even mount.
IMPORTANT ! : The optional Universal Hardware Kit -
Long Screws (see Parts drawing) may be used if there is
interference with any part of the projector, and more
height is required to clear elevated surfaces of the
projector.
Figure 3
(B)
locking button x 2
clip cover
sliding stud mount
bracket and screw
2
1
screw adapter
height-adjustment nut
(side view)
screw adapters
(M, N, P, Q or R)
with nuts
(S) x 3 or 4
(with M or N only)
2
fully lowered
3
SLBU/SLMU Installation Instructions
6
4. Place SLBU/SLMU legs (B) over screw adapters and
height-adjustment nuts. (See Figure 4)
NOTE: Make sure arm latch clips are in the unlocked position.
Figure 4
5. Press locking buttons on SLBU/SLMU leg (B) firmly and
simultaneously push clip cover away from enclosed sliding
stud mount bracket until clip cover is in the locked position.
(See Figure 5)
6. Repeat Step 5 for remaining legs.
WARNING: Make sure legs have securely locked onto
height-adjustable nuts with the latch clips. If the legs are not
properly locked onto the adapters, the projector could fall
from the SLBU/SLMU mount causing SERIOUS INJURY or
DEATH!
Figure 5
7. Manuever legs so that sliding stud mount brackets and
screws are towards the middle of the projector. (See
Figure 6) and (See Figure 7)
8. Position sliding stud mount brackets and screws so that
SLBU or SLMU main plate (A) can be evenly mounted to
legs. (See Figure 6) and (See Figure 7)
9. Use 1/4" hex key (U) to secure Allen nuts (T) to screws on
sliding stud mounts. (See Figure 6) and (See Figure 7)
NOTE: The following examples are two of many possible
scenarios based on typical examples of mounting hole
patterns. Specific connection points will vary based on
the hole pattern. Multiple scenarios may be used for
each specific hole pattern as long as the weight of the
projector is centered and balanced after mounting.
Figure 6
Figure 7
(B) x 3 or 4
open position
locked position
5
locking buttons
Three-hole scenario example (T) x 3
9
(A)
sliding stud mount
brackets and
screws
Four-hole scenario example
(A) (T) x 4
sliding stud mount
brackets and
screws
9
Installation Instructions SLBU/SLMU
7
Attach SLBU/SLMU to RPA or RPM
1. On SLBU, partially install four thumb nuts (D) to SLBU main
plate screws. Be sure to install thumb nuts with tapered side
down. (See Figure 8)
NOTE: If using optional security brackets (C) to connect SLBU
bracket to RPA or non-locking RPM mount, refer to
Security Bracket Installation section prior to installing
thumb nuts.
Figure 8
2. Attach SLBU/SLMU to RPA/RPM. Refer to RPA/RPM
installation manual for details.
Security Screw Installation (Optional)
1. Install #8-32 x 3/8" button head security screws (K) into
security holes on SLBU/SLMU legs. (See Figure 9)
NOTE: Up to two security screws can be installed on each leg.
It is recommended that screws be installed in holes that
are difficult to access to achieve maximum security.
NOTE: Cable ties (not included) may be used instead of the
security screws. Thread cable tie through both holes on
leg and secure cable tie.
Figure 9
Security Bracket Installation (Optional)
NOTE: Security brackets (C) can only be used when
connecting SLBU bracket to RPA or non-locking RPM
mounts.
1. Install security brackets (C) over screws on SLBU main
plate. (See Figure 10)
2. Partially install thumb nuts (D) onto SLBU main plate
screws. (See Figure 10)
Figure 10
(D) x 4
(A)
1
Install thumb nuts
with tapered
side down
(K)
(B)
1
security hole
(D) x 4
(C) x 2
2
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
SLBU/SLMU Installation Instructions
Chief Manufacturing, a products division
of Milestone AV Technologies
8802-002058 Rev00
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
04/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Chief SLMU Guide d'installation
- Catégorie
- Mur
- Taper
- Guide d'installation
- Ce manuel convient également à
dans d''autres langues
- English: Chief SLMU Installation guide