VTech IS8121 Manuel utilisateur

Marque: VTech

Modèle: IS8121

Catégorie: Téléphones

Taper: Manuel utilisateur

Speciﬁcations are subject to change without notice.

Technical speciﬁcations

Frequency

control Crystal controlled PLL synthesizer

Transmit

frequency Handset: 1921.536-1928.448 MHz

Telephone base: 1921.536-1928.448 MHz

Channels DECT channel: 5

Nominal

effective

range

Maximum power allowed by FCC and IC.

Actual operating range may vary according to

environmental conditions at the time of use.

Power

requirement

Handset: 2.4 VDC, AAA x 2, Ni-MH battery

Telephone base: 6V DC @ 0.4A

Charger: 6V DC @ 0.4A

Memory Phonebook: 1000 memory locations;

up to 30 digits and 15 characters

Caller ID log: 50 memory locations;

up to 24 digits and 15 characters

Call block: 1000 entries

Go to www.vtechphones.com (US)

to register your product for enhanced

warranty support and latest VTech

product news.

Go to phones.vtechcanada.com (CA)

for latest VTech product news.

Quick start guide

IS8121

IS8121-2

IS8121-3

IS8121-4

IS8121-5

IS8122-3

IS8122-4

DECT 6.0 Cordless telephone

with BLUETOOTH® wireless technology

Phonebook

The phonebook can store up to 1000 entries, which are shared

by all handsets. Each entry may consist of a telephone number

up to 30 digits, and a name up to 15 characters.

Add a phonebook entry

Review phonebook entries

Delete a phonebook entry

When your desired phonebook entry displays:

Caller ID

If you subscribe to caller ID service, information about each

caller appears after the ﬁrst or second ring.

The caller ID log stores up to 50 entries. Each entry has up

to 24 digits for the phone number and 15 characters for the

name.

Review caller ID log entries

Telephones identiﬁed with this logo have reduced noise and

interference when used with most T-coil equipped hearing aids and

cochlear implants. The TIA-1083 Compliant Logo is a trademark of

the Telecommunications Industry Association. Used under license.

Compatible with

Hearing Ai

d T-Coil

TIA-1083

The ENERGY STAR® program (www.energystar.gov) recognizes and

encourages the use of products that save energy and help protect our

environment. We are proud to mark this product with the ENERGY

STAR® label indicating it meets the latest energy efﬁciency guidelines.

Volume

Press

- OR -

Put the handset

in the telephone

base or charger

End a home call

Answer a home call

Make a home call

Press

- OR -

Enter the phone number.

ECO

HANDSET

10:15pm 12/25 10:15pm 12/25

595-9511_

ECO

Enter number

595-9511_

ECO

Enter name

ECO

Mike Smith

ECO

HANDSET

10:15pm 12/25

Mike Smith

800-595-9511

ECO

Mike Smith

800-595-9511

ECO

Delete entry ?

ECO

HANDSET

10:15pm 12/25

Dial a caller ID log entry

When your

desired caller ID

entry displays

on the handset

screen:

Press - OR - - OR -

Save a caller ID log entry to the phonebook

Delete a caller ID log entry

When your

desired caller ID

entry displays

on the handset

screen:

When your

desired caller ID

entry displays

on the handset

screen:

Press

ECO

Mike Smith

595-9511

NEW

09:05pm 12/25

ECO

Mike Smith

595-9511

NEW

09:05pm 12/25

ECO

Mike Smith

595-9511

NEW

09:05pm 12/25

>To Phonebook

ECO

Enter number

800-595-9511_

ECO

Mike Smith_

ECO

Important safety instructions

When using your telephone equipment, basic

safety precautions should always be followed

to reduce the risk of ﬁre, electric shock and

injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked

on the product.

3. CAUTION: Do not install the telephone base

at a height above 2 meters.

4. Unplug this product from the wall outlet

before cleaning. Do not use liquid or aerosol

cleaners. Use a damp cloth for cleaning.

5. Do not use this product near water such as

near a bath tub, wash bowl, kitchen sink,

laundry tub or a swimming pool, nor in a wet

basement or shower.

6. Do not place this product on an unstable

table, shelf, stand or other unstable surfaces.

7. Avoid placing the telephone system in

places with extreme temperature, direct

sunlight, or other electrical devices. Protect

your phone from moisture, dust, corrosive

liquids and fumes.

8. Slots and openings in the back or bottom

of the telephone base and handset are

provided for ventilation. To protect them

from overheating, these openings must not

be blocked by placing the product on a

soft surface such as a bed, sofa or rug. This

product should never be placed near or over

a radiator or heat register. This product should

not be placed in any area where proper

ventilation is not provided.

9. This product should be operated only from

the type of power source indicated on the

marking label. If you are not sure of the type

of power supply in your home or office,

consult your dealer or local power company.

10. Do not allow anything to rest on the power

cord. Do not install this product where the

cord may be walked on.

11. Never push objects of any kind into this

product through the slots in the telephone

base or handset because they may touch

dangerous voltage points or create a short

circuit. Never spill liquid of any kind on the

product.

12. To reduce the risk of electric shock, do not

disassemble this product, but take it to

an authorized service facility. Opening or

removing parts of the telephone base or

handset other than speciﬁed access doors

may expose you to dangerous voltages

or other risks. Incorrect reassembling can

cause electric shock when the product is

subsequently used.

13. Do not overload wall outlets and extension

cords.

14. Unplug this product from the wall outlet and

refer servicing to an authorized service facility

under the following conditions:

• When the power supply cord or plug is

damaged or frayed.

• If liquid has been spilled onto the

product.

• If the product has been exposed to rain

or water.

• If the product does not operate normally

by following the operating instructions.

Adjust only those controls that are covered

by the operation instructions. Improper

adjustment of other controls may result

in damage and often requires extensive

work by an authorized technician to

restore the product to normal operation.

• If the product has been dropped and

the telephone base and/or handset has

been damaged.

• If the product exhibits a distinct change

in performance.

15. Avoid using a telephone (other than cordless)

during an electrical storm. There is a remote

risk of electric shock from lightning.

16. Do not use the telephone to report a gas

leak in the vicinity of the leak. Under certain

circumstances, a spark may be created when

the adapter is plugged into the power

outlet, or when the handset is replaced in

its cradle. This is a common event associated

with the closing of any electrical circuit.

The user should not plug the phone into a

power outlet, and should not put a charged

handset into the cradle, if the phone is

located in an environment containing

concentrations of flammable or flame-

supporting gases, unless there is adequate

ventilation. A spark in such an environment

could create a fire or explosion. Such

environments might include: medical use

of oxygen without adequate ventilation;

industrial gases (cleaning solvents; gasoline

vapors; etc.); a leak of natural gas; etc.

17. Only put the handset of your telephone next

to your ear when it is in normal talk mode.

18. The power adapter is intended to be

correctly oriented in a vertical or ﬂoor mount

position. The prongs are not designed to hold

the plug in place if it is plugged into a ceiling,

under-the-table or cabinet outlet.

19. For pluggable equipment, the socket-outlet

shall be installed near the equipment and shall

be easily accessible.

20. CAUTION: Use only the batteries

indicated in this manual. There may be a risk

of explosion if a wrong type of battery is

used for the handset. Use only the supplied

rechargeable batteries or replacement

batteries (BT162342/BT262342) for the

handset. Do not dispose of batteries in a

ﬁre. They may explode.

• Do not use the battery in following

conditions:

» High or low extreme temperature

during use, storage or

transportation.

» Replacement of a battery with an

incorrect type that can defeat a

safeguard.

» Disposal of a battery into ﬁre or a

hot oven, or mechanically crushing

or cutting of a battery, that can

result in an explosion.

» Leaving a batteryin an extremely

high temperature surrounding

environment that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

» A battery subjected to extremely

low air pressure that can result in

an explosion or the leakage of

ﬂammable liquid or gas.

21. Use only the adapter included with this

product. Incorrect adapter polarity or

voltage can seriously damage the product.

22. The applied nameplate is located at the

bottom or near of the product.

SAVE THESE INSTRUCTIONS

Battery

• Use only the battery provided or equivalent.

To order a replacement, visit our website at

www.vtechphones.com or call 1 (800) 595-

9511. In Canada, go to phones.vtechcanada.

com or call 1 (800) 267-7377.

• Do not dispose of the battery in a ﬁre. Check

with local waste management codes for

special disposal instructions.

• Do not open or mutilate the battery. Released

electrolyte is corrosive and may cause burns

or injury to the eyes or skin. The electrolyte

may be toxic if swallowed.

• Exercise care in handling batteries in order

not to create a short circuit with conductive

materials.

• Charge the battery provided with this

product only in accordance with the

instructions and limitations speciﬁed in this

manual.

Precautions for users of implanted cardiac

pacemakers

Cardiac pacemakers (applies only to digital

cordless telephones):

Wireless Technology Research, LLC (WTR),

an independent research entity, led a

multidisciplinary evaluation of the interference

between portable wireless telephones and

implanted cardiac pacemakers. Supported by

the U.S. Food and Drug Administration, WTR

recommends to physicians that:

Pacemaker patients

• Should keep wireless telephones at least six

inches from the pacemaker.

• Should NOT place wireless telephones

directly over the pacemaker, such as in a

breast pocket, when it is turned ON.

• Should use the wireless telephone at the

ear opposite the pacemaker.

WTR’s evaluation did not identify any risk

to bystanders with pacemakers from other

persons using wireless telephones.

About cordless

telephones

• Privacy: The same features that make a

cordless telephone convenient create

some limitations. Telephone calls are

transmitted between the telephone

base and the cordless handset by radio

waves, so there is a possibility that the

cordless telephone conversations could be

intercepted by radio receiving equipment

within range of the cordless handset. For

this reason, you should not think of cordless

telephone conversations as being as

private as those on corded telephones.

• Electrical power: The telephone base of

this cordless telephone must be connected

to a working electrical outlet. The electrical

outlet should not be controlled by a wall

switch. Calls cannot be made from the

cordless handset if the telephone base is

unplugged, switched off or if the electrical

power is interrupted.

• Potential TV interference: Some cordless

telephones operate at frequencies that may

cause interference to televisions and VCRs.

To minimize or prevent such interference,

do not place the telephone base of the

cordless telephone near or on top of a

TV or VCR. If interference is experienced,

moving the cordless telephone farther

away from the TV or VCR often reduces or

eliminates the interference.

• Rechargeable batteries: Exercise care in

handling batteries in order not to create a

short circuit with conducting material such

as rings, bracelets and keys. The battery or

conductor may overheat and cause harm.

Observe proper polarity between the

battery and the battery charger.

• Nickel-metal hydride rechargeable

batteries: Dispose of these batteries in a

safe manner. Do not burn or puncture the

battery. Like other batteries of this type, if

burned or punctured, they could release

caustic material which could cause injury.

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2035

Quick

start

guide

1 set for IS8121

2 sets for IS8121-2

3 sets for IS8121-3

3 sets for IS8122-3

4 sets for IS8121-4

4 sets for IS8122-4

5 sets for IS8121-5

1 set for IS8121-2

2 sets for IS8121-3

2 sets for IS8122-3

3 sets for IS8121-4

3 sets for IS8122-4

4 sets for IS8121-5

Introducing

Smart call

blocker

What’s in the box

Connect the telephone base

If you subscribe to

digital subscriber

line (DSL) high-

speed Internet

service through

your telephone

line, make sure

you connect a

DSL ﬁlter (not

included) to the

telephone wall

jack.

Install the battery

Connect the charger

Charge the battery

12 hrs

Display

The battery is low and needs

charging.

The battery is charging.

The battery is fully charged.

Handset ringer is off.

New voicemail received from your

telephone service provider.

NEW

There are new caller ID log entries.

ANS ON Answering system is on.

MSG#

5/10 Number of new/old messages

recorded.

ECO The ECO mode activates automatically

to reduce power consumption when

the handset is within range of the

telephone base.

HANDSET

ECO

NEW

ANS ON

10:15

MSG#

5/10

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 300mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR2035

THIS SIDE UP

P / CE CÔTÉ VERS LE HAUT

oc-piles :

3342 (2.4V 400mAh Ni-MH)

VERTISSEMENT :

RPUNCTURE BATTERIES.

UPERCER LES PILES.

chine CR1535

After you install your telephone or power returns following a

power outage and battery depletion, the handset will prompt

you to set the date and time, and to conﬁgure the Smart call

blocker* and answering system through voice guide.

When the handset

prompts you to set

the date and time

Date and time

Follow the steps below to set the date and time. For example,

if the date is 25 December, 2019, and the time is 10:59 AM:

Date: MM/DD/YY

ECO

Date: 12/2?/YY

ECO

Date: 12/25/19

ECO

Time: 1?:MM --

ECO

Time: 10:59 AM

ECO

Enter the date.

2Press SELECT.

3Enter the time. 4Press SELECT.

Voice guide for Smart call blocker

After setting the date and time, the handset will prompt if you

want to set Smart call blocker. For more details, see Use voice

guide to set Smart call blocker in the Introducing Smart call

blocker leaﬂet.

Setup your Smart call blocker by

inputting the designated numbers as

instructed in the voice guide.

“Hello! This voice guide will assist

you with the basic setup of Smart

call blocker“

When the handset prompts you to set up the Smart call blocker via

voice guide

Smart call blk?

ECO

Press SELECT.

Voice guide for answering system

After setting the Smart call blocker, the handset will display

Voice guide to set up Answering system?

This feature assists you to do the basic setup of the answering

system. You can follow the voice guide to record your own

announcement, set the number of rings and the message alert

tone.

When the handset prompts you to set up the answering system via

voice guide

set up Ans sys?

ECO

Press SELECT.

Setup your answering system by

inputting the designated numbers

as instructed in the voice guide.

“This voice guide will assist you with

the basic setup of your answering

system“

Connect and install

Setup

Make a cell call

1 Press .

Answer a cell call

- OR - - OR -

Press any

dialing

keys

- OR - - OR -

Press any

dialing

keys

End a cell call

Press

- OR -

Put the handset

in the telephone

base or charger

Press

*Includes licenced QaltelTM technology.

QaltelTM is a trademark of Truecall Group Limited.

LCD language setting

If you accidentally set the LCD language to Spanish or French, press MENU and then enter 364# to change the handset LCD

language back to English while the handset is not in use.

Enter the phone

number. 2

Press MENU.

Press SELECT.

Enter the name.

Press SELECT.

Press , then the

number of entries

displays.

Press / to

browse the entries.

Press DELETE.

Press SELECT.

Phonebook

Basic operation Caller ID

Press / to select a device,

then press MENU/SELECT.

3 Enter the phone number. Mike Smith

800-595-9611

ECO

Dial a phonebook entry

When your desired phonebook entry displays:

Mike Smith

800-595-9511

ECO

Press

- OR - - OR -

Press CID.

Press / to

browse the entries.

Press MENU.2Press SELECT to

select To

Phonebook.

3Edit the number

if needed, then

press SELECT.

4Edit the name

if needed, then

press SELECT.

09:05pm 12/25

Mike Smith

595-9511

ECO

Deleting...

ECO

Press

The Bluetooth® word mark and logos are owned by Bluetooth SIG, Inc. and any use

of such marks by VTech Holdings Limited is under license. VTech Holdings Limited is

a member of Bluetooth SIG, Inc. Other trademarks and trade names are those of their

respective owners.

Press again to dial.

Scan the QR code for

support information

Follow the steps to

set the date and time

if you skipped the

prompt.

Press / to

scroll to Set date/time,

then press SELECT.

Press MENU.

Enter the date, then

press SELECT.

Enter the time, then

press SELECT.

HANDSET 1

ECO

10:30PM 11/20

Set date/time

ECO

Date: 12/25/19

ECO

Time: 10:59 AM

ECO

Improve the telephone signal

strength

NOTESNOTE

Note

• To avoid interference, place the

telephone base in a central location of

the house and at least 3 feet (1 meter)

away from thick walls as well as other

household appliances such as, TV,

radio, microwave oven, Wi-Fi router,

large mirror, metal furniture and ﬁsh

tank.

> 1 m (3 feet)

(3(3

etet

))

See Mount the telephone base (optional) online for the

wall mounting instructions.

Tip

US CA

You can pair and connect your cordless telephone with Bluetooth enabled cellular phones. Before you begin, make sure that you have cellular coverage and your Bluetooth enabled cell phone is not

connected to any other Bluetooth device.

Add a cell phone

1. Press and hold CELL 1 or CELL 2 on the telephone base

for about four seconds until the CELL 1 or CELL 2 light

ﬂashes.

2. Turn on the Bluetooth feature of your cell phone and

search for or add new devices.

3. Once your cell phone ﬁnds your telephone

(VTech DECT 6.0), press the appropriate key on your cell

phone to continue the pairing process.

4. When a device is successfully paired and connected, the

corresponding status icon (CELL 1 or CELL 2) displays.

The corresponding device light on the telephone base

turns on.

Add a headset Activate remote voice control

1. Press VOICE on the handset.

2. The handset then shows the remote voice control icon .

3. Speak toward the handset and wait for feedback.

4. Press on the handset to end the current remote

voice control session.

Download a cell phone directory

Before downloading a directory, make sure the cell phone is

paired, active, and connected to your IS8121/IS8121-2/IS8121-3/

IS8121-4/IS8121-5.

About the built-in answering system and voicemail service

For message recording, your telephone has a built-in answering system, and it also supports voicemail

service offered by your telephone service provider (subscription is required, and fee may apply).

Built-in answering system VS Voicemail service

Built-in answering system Voicemail service

Supported by Telephone system Telephone service provider

Subscription No Yes

Fees No May apply

Answer incoming calls • After 3 rings by default.

• It can be changed in the handset menu.

• Usually after 2 rings.

• It can be changed by contacting your

telephone service provider.

Storage Telephone- base Server or System

Display new messages • Handset - XX New Msg

• Telephone base - XX New Msg • Handset - and New voicemail

Retrieve messages

• Press on the telephone base; OR

• Press MENU, and then select Play

messages on the handset; OR

• Access remotely with an access code.

• Press on the dialpad, and enter an

access number and/or passcode from

your telephone service provider.

HANDSET

ECO 1

10:30PM 11/20

ECO

Bluetooth

ECO

Need help?

For operations and guides to help you use your telephone, and for latest

information and supports, go and check the online help topics and online FAQs.

Use your smartphone or mobile device to access our online help.

• Go to https://help.vtechphones.com/is8121;

https://help.vtechphones.com/is8122 OR

• Scan the QR code on the right. Launch the camera app or QR code

scanner app on your smartphone or tablet. Hold the device’s camera

up to the QR code and frame it. Tap the notiﬁcation to trigger the

redirection of the online help.

- If the QR code is not clearly displayed, adjust your camera’s focus by

moving your device closer or further away until it is clear.

You can also call our Customer Support at 1 (800) 595-9511 [in US] or

1 (800) 267-7377 [in Canada] for help.

Answering system

Bluetooth For C-UL compliance only

Mesures de sécurité importantes

Aﬁn de réduire les risques d’incendie, de

blessures corporelles ou d’électrocution,

suivez toujours ces mesures préventives de

base lorsque vous utilisez votre téléphone :

1. Lisez et comprenez bien toutes les

instructions.

2. Observez toutes les instructions et mises

en garde inscrites sur l’appareil.

3. ATTENTION: Ne pas installer le socle

téléphonique à une hauteur supérieure

à 2 mètres.

4. Débranchez ce téléphone de la prise

murale avant de le nettoyer. N’utilisez

pas de nettoyeurs liquides ni en

aérosol. N’utilisez qu’un chiffon doux et

légèrement humecté.

5. N’utilisez pas ce produit près de l’eau,

tel que près d’un bain, d’un lavabo, d’un

évier de cuisine, d’un bac de lavage

ou d’une piscine, ou dans un sous-sol

humide ou sous la douche.

6. Ne déposez pas ce téléphone sur un

chariot, support ou table chancelants.

L’appareil pourrait tomber et être

sérieusement endommagé.

7. Évitez d’installer le système

téléphonique dans les endroits

soumis à une température extrême,

à la lumière directe du soleil ou

à proximité immédiate d’autres

appareils électriques ou électroniques.

Protégez votre téléphone contre les

sources d’humidité, la poussière, les

vapeurs et les liquides corrosifs.

8. Le boîtier de l’appareil est doté de fentes

et d’ouvertures d’aération situées à

l’arrière ou en dessous. Aﬁn d’empêcher

la surchauffe, ces ouvertures ne doivent

pas être obstruées en plaçant l’appareil

sur un lit, divan, tapis ou autre surface

similaires. Ne placez pas cet appareil à

proximité d’un élément de chauffage

ni d’une plinthe électrique. De plus, ne

l’installez pas dans une unité murale ou

un cabinet fermé qui ne possède pas

d’aération adéquate.

9. Ne faites fonctionner cet appareil

qu’avec le type d’alimentation indiqué

sur les étiquettes de l’appareil. Si vous

ne connaissez pas le voltage de votre

maison, consultez votre marchand ou

votre fournisseur d’électricité.

10. Ne déposez rien sur le cordon

d’alimentation. Installez cet appareil

dans un endroit sécuritaire, là où

personne ne pourra trébucher sur

la ligne d’alimentation ni le cordon

téléphonique modulaire.

11. N’insérez jamais d’objets à travers les

fentes et ouvertures de cet appareil,

car ils pourraient toucher à des points

de tension dangereux ou court-circuiter

des pièces, ce qui constituerait un

risque d’incendie ou d’électrocution.

N’échappez pas de liquides dans

l’appareil.

12. Aﬁn de réduire les risques

d’électrocution, ne démontez pas

l’appareil, mais apportez-le plutôt

à un centre de service qualiﬁé s’il

doit être réparé. En enlevant le

couvercle, vous vous exposez à des

tensions dangereuses ou autres

dangers similaires. Un remontage

inadéquat peut être à l’origine d’une

électrocution lors d’une utilisation

ultérieure de l’appareil. Débranchez

l’appareil avant de procéder au

nettoyage. Utilisez un chiffon humide

et doux.

13. Ne surchargez pas les prises de courant

et les rallonges.

14. Débranchez cet appareil de la prise

de courant et communiquez avec le

département de service à la clientèle

de VTech dans les cas suivants :

• Lorsque le cordon d’alimentation est

endommagé ou écorché.

• Si du liquide a été échappé dans

l’appareil.

• Si l’appareil a été exposé à une source

d’humidité telle que la pluie ou l’eau.

• Si le produit ne fonctionne pas

normalement en respectant les

instructions de fonctionnement.

Réglez uniquement les commandes

indiquées dans le les instructions

de fonctionnement. Les réglages

incorrects des autres commandes

pourraient provoquer un dommage

qui pourrait exiger un travail exhaustif

de la part d’un technicien autorisé

aﬁn de rétablir le fonctionnement

normal de l’appareil.

• Si le produit a été échappé et que

le socle et/ou le combiné a été

endommagé.

• Si le produit affiche une nette

diminution de sa performance.

15. Évitez d’utiliser un téléphone (autre

qu’un sans ﬁl) pendant un orage. Les

éclairs peuvent être à l’origine d’une

électrocution.

16. N’utilisez pas le téléphone pour

rapporter une fuite de gaz à proximité

de la fuite. En certaines circonstances,

une flammèche pourrait être

provoquée lorsque l’adaptateur est

branché à une prise de courant, ou

lorsque le combiné est déposé sur le

socle. Ceci est un événement commun

associé à la fermeture d’un circuit

électrique. L’utilisateur ne devrait

pas brancher le téléphone à une

prise de courant, et ne devrait pas

déposer le combiné chargé sur le

socle, si le téléphone se trouve à

proximité d’un endroit comportant des

concentrations de gaz inﬂammables, à

moins que la ventilation soit adéquate.

Une flammèche dans un tel endroit

pourrait provoquer un incendie ou

une explosion. De tels environnements

peuvent comprendre: des endroits

où l’on utilise de l’oxygène médical

sans ventilation adéquate; des gaz

industriels (dissolvants de nettoyage,

des vapeurs d’essence, etc.); une fuite

de gaz naturel, etc.

17. Ne placez que le combiné de votre

téléphone près de votre oreille

lorsqu’en mode de conversation.

18. Ces adaptateurs ont été conçus pour

être orientés en position verticale ou

montés au sol. Les broches ne sont pas

conçues pour maintenir l’adaptateur en

place si celui-ci est barnché dans une

prise au plafond ou sous une table/

armoire.

19. Pour le MATERIEL RACCORDE PAR

PRISE DE COURANT, le socle de prise de

courant doit etre installe a proximite du

materiel et doit etre aisement accessible.

20. MISE EN GARDE: Il peut y

avoir un risque d’explosion si vous

utilisez le mauvais type de piles pour le

téléphone. N’utilisez que les piles

rechargeable inclus ou les piles de

rechange (BT162342/BT262342).

N’incinérez pas les piles. Celles-ci

risqueraient d’exploser.

• Évite d’utiliser la batterie dans les

conditions suivantes:

»des températures extrêmes

faibles ou élevées auxquelles

une batterie peut être soumise

pendant l’utilisation, le stockage ou

le transport;

»Remplacement d’une batterie

par un type incorrect pouvant

supprimer une protection;

»mise au rebut d’une batterie dans

un feu ou dans un four chaud, ou

écrasement mécanique ou coupure

d’une batterie, susceptible de

provoquer une explosion;

»maintien d’une batterie dans

un environnement à très haute

température pouvant provoquer

une explosion ou la fuite de liquide

ou de gaz inﬂammables;

»batterie soumise à une pression de

l’air extrêmement faible pouvant

provoquer une explosion ou la fuite

de liquide ou de gaz inﬂammables.

21. N’utilisez que les adaptateurs inclus

avec ce produit. L’utilisation d’un

adaptateur dont la polarité ou la

tension serait inadéquate risque

d’endommager sérieusement le

produit et mettre votre sécurité en

péril.

22. La plaque signalétique appliquée est

située au bas ou à proximité du produit.

CONSERVEZ CES INSTRUCTIONS

Pile

• N’utilisez que la pile incluse ou

l’équivalent. Pour commander une pile

de recharge, visitez notre site Web au

www.vtechphones.com ou composez

le 800-595-9511. Au Canada, visitez

le phones.vtechcanada.com ou

composez le 800-267-7377.

• Ne jetez pas la pile au feu. Vériﬁez les

instructions spéciﬁques de mise aux

rebus auprès des autorités locales.

• N’ouvrez pas et ne mutilez pas la pile.

L’électrolyte qui s’en échapperait est

corrosif et pourrait causer des brûlures

ou des blessures aux yeux ou à la

peau. L’électrolyte est toxique si avalé.

• Soyez prudents lorsque vous

manipulez les piles aﬁn d’éviter les

courts-circuits provoqués par des

matériaux conducteurs.

• Rechargez la pile incluse avec cet

appareil, selon les instructions et

limites spéciﬁées dans ce guide

d’utilisation.

Stimulateurs cardiaques implantés dans

l’organisme

Les simulateurs cardiaques (s’applique

uniquement aux téléphones numériques

sans ﬁl) :

L’organisme ‘Wireless Technology

Research, LLC (WTR)’, une ﬁrme de

recherche indépendante, a mené

une évaluation pluridisciplinaire des

interférences entre les téléphones sans

ﬁl portatifs et les stimulateurs cardiaques

implantés dans l’organisme. Appuyée par

l’Administration des aliments et drogues

(FDA) des États-Unis, la ﬁrme WTR

recommande aux médecins :

Avis aux détenteurs de stimulateurs

cardiaques

• Ils doivent tenir le téléphone sans ﬁl à

une distance d’au moins six pouces du

stimulateur cardiaque.

• Ils ne doivent PAS placer le téléphone

sans ﬁl directement sur le stimulateur

cardiaque, tel que dans une poche

de chemise, lorsque celui-ci est en

marche.

• Ils doivent utiliser le téléphone sans

ﬁl en l’appuyant sur l’oreille qui se

trouve dans la direction opposée au

stimulateur cardiaque.

L’étude effectuée par l’organisme WRS n’a

pas identiﬁé de risque pour les détenteurs

de simulateurs cardiaques causés par les

gens qui utilisent un téléphone sans ﬁl à

proximité de ceux-ci.

À propos des téléphones sans ﬁl

Conﬁdentialité : Les mêmes

caractéristiques qui constituent des

avantages pour les téléphones sans ﬁl

afﬁchent également des restrictions.

Les appels téléphoniques sont transmis

entre le combiné sans ﬁl et le socle

par le biais d’ondes radio ; il y a donc

la possibilité que vos conversations

téléphoniques sans ﬁl soient interceptées

par des équipements de réception radio

se trouvant dans la portée du combiné

sans ﬁl. Pour cette raison, vous ne devez

pas percevoir les communications

téléphoniques sans ﬁl comme étant aussi

conﬁdentielles que celles des téléphones

à cordons.

Alimentation électrique : Le socle de ce

téléphone sans ﬁl doit être branché à une

prise électrique fonctionnelle. La prise

électrique ne doit pas être contrôlée

par un interrupteur mural. Les appels ne

pourront pas être effectués du combiné

sans ﬁl si le socle est débranché ou mis

hors tension ou si le courant est coupé.

Possibilité d’interférences aux téléviseurs

: Certains téléphones sans ﬁl fonctionnent

sur des fréquences pouvant causer des

interférences aux téléviseurs et aux

magnétoscopes. Pour réduire ou prévenir

de telles interférences, ne placez pas le

socle du téléphone sans ﬁl près ou sur

un téléviseur ou magnétoscope. S’il y

a présence de parasites, il est conseillé

d’éloigner le téléphone sans ﬁl du

téléviseur ou du magnétoscope aﬁn de

réduire possiblement les interférences.

Piles rechargeables : Manipulez les piles

avec soin aﬁn de ne pas les court-circuiter

avec des bagues, bracelets ou clés. Les

piles ou le conducteur peut surchauffer et

causer des blessures. Respectez la polarité

adéquate entre la pile et le chargeur.

Les bloc-piles rechargeables à l’hydrure

métallique de nickel : Jetez ces blocs-piles

de manière écologique et sécuritaire.

Ne les incinérez pas et ne les percez pas.

Tel que les autres piles de ce type, elles

pourraient dégager une matière toxique

qui peut causer des blessures corporelles

si elles sont brûlées ou percées.

The RBRC® seal

The RBRC seal on the nickel-metal hydride battery indicates that VTech

Communications, Inc. is voluntarily participating in an industry program to

collect and recycle these batteries at the end of their useful lives, when

taken out of service within the United States and Canada.

The RBRC program provides a convenient alternative to placing used

nickel-metal hydride batteries into the trash or municipal waste, which

may be illegal in your area.

VTech’s participation in RBRC makes it easy for you to drop off the spent battery at local

retailers participating in the RBRC program or at authorized VTech product service

centers. Please call 1 (800) 8 BATTERY® for information on Ni-MH battery recycling and

disposal bans/restrictions in your area. VTech’s involvement in this program is part of its

commitment to protecting our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC, ACTA and IC regulations

FCC Part 15

NOTE: This equipment has been tested and found to comply with the requirements

for a Class B digital device under Part 15 of the Federal Communications Commission

(FCC) rules. These requirements are intended to provide reasonable protection against

harmful interference in a residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: Changes or modiﬁcations to this equipment not expressly approved by

the party responsible for compliance could void the user’s authority to operate the

equipment.

This device complies with Part 15 of the FCC rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause

undesired operation. Privacy of communications may not be ensured when using this

telephone.

To ensure safety of users, the FCC has established criteria for the amount of radio

frequency energy that can be safely absorbed by a user or bystander according to the

intended usage of the product. This product has been tested and found to comply

with the FCC criteria. The handset may be safely held against the ear of the user. The

telephone base shall be installed and used such that parts of the user’s body other than

the hands are maintained at a distance of approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B).

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and with technical requirements

adopted by the Administrative Council for Terminal Attachments (ACTA). The label

on the back or bottom of this equipment contains, among other things, a product

identiﬁer in the format US:AAAEQ##TXXXX. This identiﬁer must be provided to your

telephone service provider upon request.

The plug and jack used to connect this equipment to premises wiring and the

telephone network must comply with applicable Part 68 rules and technical

requirements adopted by ACTA. A compliant telephone cord and modular plug is

provided with this product. It is designed to be connected to a compatible modular

jack that is also compliant. An RJ11 jack should normally be used for connecting to a

single line and an RJ14 jack for two lines. See the installation instructions in the user’s

manual.

The Ringer Equivalence Number (REN) is used to determine how many devices you

may connect to your telephone line and still have them ring when you are called.

The REN for this product is encoded as the 6th and 7th characters following the US:

in the product identiﬁer (e.g., if ## is 03, the REN is 0.3). In most, but not all areas, the

sum of all RENs should be ﬁve (5.0) or less. For more information, please contact your

telephone service provider.

This equipment must not be used with Party Lines. If you have specially wired alarm

dialing equipment connected to your telephone line, ensure the connection of this

equipment does not disable your alarm equipment. If you have questions about what

will disable alarm equipment, consult your telephone service provider or a qualiﬁed

installer.

If this equipment is malfunctioning, it must be unplugged from the modular jack until

the problem has been corrected. Replacement to this telephone equipment can only

be made by the manufacturer or its authorized agents. For replacement procedures,

follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network, the telephone service

provider may temporarily discontinue your telephone service. The telephone service

provider is required to notify you before interrupting service. If advance notice is not

practical, you will be notiﬁed as soon as possible. You will be given the opportunity to

correct the problem and the telephone service provider is required to inform you of

your right to ﬁle a complaint with the FCC. Your telephone service provider may make

changes in its facilities, equipment, operation, or procedures that could affect the

proper functioning of this product. The telephone service provider is required to notify

you if such changes are planned.

If this product is equipped with a corded or cordless handset, it is hearing aid

compatible.

If this product has memory dialing locations, you may choose to store emergency

telephone numbers (e.g., police, ﬁre, medical) in these locations. If you do store or test

emergency numbers, please:

Remain on the line and brieﬂy explain the reason for the call before hanging up.

Perform such activities in off-peak hours, such as early morning or late evening.

Industry Canada

This device contains licence-exempt transmitter(s)/receiver(s) that comply with

Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).

Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause

undesired operation of the device.

Privacy of communications may not be ensured when using this telephone.

The term ‘’IC:‘’ before the certiﬁcation/registration number only signiﬁes that the

Industry Canada technical speciﬁcations were met.

The Ringer Equivalence Number (REN) for this terminal equipment is 1.0. The REN

indicates the maximum number of devices allowed to be connected to a telephone

interface. The termination of an interface may consist of any combination of devices

subject only to the requirement that the sum of the RENs of all the devices not exceed

ﬁve.

This product meets the applicable Innovation, Science and Economic Development

Canada technical speciﬁcations.

California Energy Commission battery

charging testing instructions

This telephone is set up to comply with the energy-conserving standards right out of the

box. These instructions are intended for California Energy Commission (CEC) compliance

testing only. When the CEC battery charging testing mode is activated, all telephone

functions, except battery charging, will be disabled.

To activate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet. Make sure all

handsets are plugged with charged batteries before proceeding.

2. While you press and hold FIND HS, plug the telephone base power adapter back to

the power outlet.

3. After about 20 seconds, when the IN USE light starts ﬂashing, release FIND HS and

then press it again within two seconds. You hear a conﬁrmation tone. The IN USE

light turns off and all handsets display To register HS... see manual. Allow up to one

minute for the process to complete.

If the phone fails to enter this mode, repeat all the steps mentioned above. The

telephone base will be powered up as normal if you fail to press FIND HS within two

seconds in Step 3.

To deactivate the CEC battery charging testing mode:

1. Unplug the telephone base power adapter from the power outlet, and then plug it

back in. Then the telephone base is powered up as normal.

2. Put the handsets on the telephone base cradle to begin registration.

3. The handset shows Registering... If the registration is successful, the handset screen

displays Registered and beeps. The handset is registered with the telephone base.

Limited Warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase

(“Consumer” or “you”) that the Product and all accessories provided in the sales package

(“Product”) are free from defects in material and workmanship, pursuant to the following

terms and conditions, when installed and used normally and in accordance with the

Product operating instructions. This limited warranty extends only to the Consumer for

Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and

workmanship during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will replace at

VTech’s option, without charge, a Materially Defective Product. If we choose to replace the

Product, we may replace it with a new or refurbished Product of the same or similar design.

We will retain defective parts, modules, or equipment. Replacement of the Product, at

VTech’s option, is your exclusive remedy. VTech will return the replacement Products to you

in working condition. You should expect the replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of

purchase. If VTech replaces a Materially Defective Product under the terms of this limited

warranty, this limited warranty also applies to the replacement Product for a period of

either (a) 90 days from the date the replacement Product is shipped to you or (b) the time

remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical

damage, improper installation, abnormal operation or handling, neglect,

inundation, ﬁre, water or other liquid intrusion.

2. Product that has been subjected to contact with liquid, water, rain, extreme

humidity or heavy perspiration, sand, dirt or the like; but then only to the extent

the damage was not caused by incorrectly securing the waterproof handset’s

protective elements, for example, failing to properly close a seal), or such

protective elements are damaged or missing (e.g. a cracked battery door), or

subjecting a Product to conditions beyond its stated speciﬁcations or limits (e.g. 30

minutes in 1 meter of fresh water).

3. Product that has been damaged due to repair, alteration or modiﬁcation by

anyone other than an authorized service representative of VTech;

4. Product to the extent that the problem experienced is caused by signal conditions,

network reliability, or cable or antenna systems;

5. Product to the extent that the problem is caused by use with non-VTech

accessories;

6. Product whose warranty/quality stickers, product serial number plates or electronic

serial numbers have been removed, altered or rendered illegible;

7. Product purchased, used, serviced, or shipped for repair from outside the United

States of America or Canada, or used for commercial or institutional purposes

(including but not limited to Products used for rental purposes);

8. Product returned without a valid proof of purchase (see item 2 below); or

9. Charges for installation or set up, adjustment of customer controls, and installation or

repair of systems outside the unit.

How do you get warranty service?

To obtain warranty service in the United States of America, please visit our website at

www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to

www.vtechcanada.com or dial 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s

controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during

transit and transportation and are responsible for delivery or handling charges incurred in

the transport of the Product(s) to the service location. VTech will return replaced Product

under this limited warranty. Transportation, delivery or handling charges are prepaid.

VTech assumes no risk for damage or loss of the Product in transit. If the Product failure

is not covered by this limited warranty, or proof of purchase does not meet the terms of

this limited warranty, VTech will notify you and will request that you authorize the cost of

replacement prior to any further activity. You must pay for the cost of replacement and

return shipping costs for the replacement of Products that are not covered by this limited

warranty.

What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech

service location along with a description of the malfunction or difﬁculty; and

2. Include a “valid proof of purchase” (sales receipt) identifying the Product

purchased (Product model) and the date of purchase or receipt; and

3. Provide your name, complete and correct mailing address, and telephone

number.

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It

supersedes all other written or oral communications related to this Product. VTech

provides no other warranties for this Product. The warranty exclusively describes all of

VTech’s responsibilities regarding the Product. There are no other express warranties. No

one is authorized to make modiﬁcations to this limited warranty and you should not rely

on any such modiﬁcation.

State/Provincial Law Rights: This warranty gives you speciﬁc legal rights, and you may

also have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of ﬁtness for a particular purpose and

merchantability (an unwritten warranty that the Product is ﬁt for ordinary use) are limited

to one year from the date of purchase. Some states/provinces do not allow limitations on

how long an implied warranty lasts, so the above limitation may not apply to you. In no

event shall VTech be liable for any indirect, special, incidental, consequential, or similar

damages (including, but not limited to lost proﬁts or revenue, inability to use the Product or

other associated equipment, the cost of substitute equipment, and claims by third parties)

resulting from the use of this Product. Some states/provinces do not allow the exclusion or

limitation of incidental or consequential damages, so the above limitation or exclusion may

not apply to you.

Please retain your original sales receipt as proof of purchase

Disclaimer and Limitation of Liability

VTech Communications, Inc. and its suppliers assume no responsibility for any damage

or loss resulting from the use of this user’s manual. VTech Communications, Inc. and its

suppliers assume no responsibility for any loss or claims by third parties that may arise

through the use of this product.

Company: VTech Communications, Inc.

Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States

Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada

4Set your headset to

discoverable mode.

Press / to scroll

to Add BT headset,

then press SELECT.

5Refer to the user’s manual of

your Bluetooth headset on how

to pair it to your IS8121/

IS8121-2/IS8121-3/IS8121-4/

IS8121-5 telephone.

1Press MENU.2Press / to scroll to

Bluetooth, then press

SELECT.

Cellphone 00:03

ECO 1

10:30PM 11/20

1Press MENU.2Press / to scroll

to Bluetooth, then

press SELECT.

3Press / to scroll to

Download DIR,

then press SELECT.

Bluetooth

ECO 1

Download DIR

ECO 1

Your cell phone

ECO 1

Downloading...

ECO 1

Entries added:

ECO 1

ECO

HANDSET

10:15pm 12/25

HANDSET

10:15pm 12/25

1 1

Add BT headset

ECO 1

Search headset...

ECO 1

Set number of rings

You can set your answering system to answer calls at least two rings earlier than your voicemail service. For example, if your voicemail service answers after six

rings, set your answering system to answer after four rings. Thus, if you are on a call, or if the answering system is busy recording a message and you receive

another call, the second caller can leave a voicemail message.

HANDSET

ECO

10:30PM 11/20

1Press MENU.

ECO

5Press / to scroll to desired

number of rings, then press SELECT.

Answering sys

ECO

2Press / to scroll to

Answering sys, then