DeWalt DCH253 Manuel utilisateur

Taper
Manuel utilisateur
DCH253, DCH273
Heavy-Duty 20V Max* Cordless Rotary Hammer
Perceuse à percussion haute résistance sans fil 20 V max*
Rotomartillo inalámbrico de 20 V Máx* para trabajo pesado
INSTRUCTION MANUAL
GUIDE D'UTILISATION
MANUAL DE INSTRUCCIONES
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE
USAR EL PRODUCTO.
If you have questions or comments, contactus.
Pour toute question ou tout commentaire, nouscontacter.
Si tiene dudas o comentarios,contáctenos.
1-800-4-
DEWALT
• www.
DEWALT
.com
Final Page Size: 8.5 x 5.5"
1
English
Definitions: Safety Guidelines
The definitions below describe the level of severity for each
signal word. Please read the manual and pay attention to
thesesymbols.
DANGER: Indicates an imminently hazardous situation
which, if not avoided, will result in death or seriousinjury.
WARNING: Indicates a potentially hazardous situation which,
if not avoided, could result in death or seriousinjury.
CAUTION: Indicates a potentially hazardous situation which, if
not avoided, may result in minor or moderateinjury.
NOTICE: Indicates a practice not related to personal injury
which, if not avoided, may result in propertydamage.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR
ANY D
EWALT
TOOL, CALL US TOLL FREE AT: 1-800-4-
DEWALT
(1-800-433-9258).
WARNING: To reduce the risk of injury, read the
instructionmanual.
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in
electric shock, fire and/or seriousinjury.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) powertool.
1) WORK AREA SAFETY
a) Keep work area clean and well lit. Cluttered or dark areas
inviteaccidents.
b) Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust
orfumes.
c) Keep children and bystanders away while operating a
power tool. Distractions can cause you to losecontrol.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electricshock.
b) Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed
orgrounded.
c) Do not expose power tools to rain or wet conditions. Water
entering a power tool will increase the risk of electricshock.
d) Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electricshock.
e) When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electricshock.
f) If operating a power tool in a damp location is unavoidable,
use a ground fault circuit interrupter (GFCI) protected
supply. Use of a GFCI reduces the risk of electricshock.
2
English
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must berepaired.
c) Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power toolaccidentally.
d) Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are
dangerous in the hands of untrainedusers.
e) Maintain power tools. Check for misalignment or binding
of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged,
have the power tool repaired before use. Many accidents
are caused by poorly maintained powertools.
f) Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier tocontrol.
g) Use the power tool, accessories and tool bits, etc. in
accordance with these instructions, taking into account
the working conditions and the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardoussituation.
5) BATTERY TOOL USE AND CARE
a) Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type of
battery pack may create a risk of fire when used with another
batterypack.
b) Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of
injury andfire.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while
operating power tools may result in serious personalinjury.
b) Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-
skid safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personalinjuries.
c) Prevent unintentional starting. Ensure the switch is in
the off position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energizing power
tools that have the switch on invitesaccidents.
d) Remove any adjusting key or wrench before turning the
power tool on. A wrench or a key left attached to a rotating
part of the power tool may result in personalinjury.
e) Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpectedsituations.
f) Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewelry or long hair can be caught in
movingparts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-relatedhazards.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job
better and safer at the rate for which it wasdesigned.
3
English
Wear safety goggles or other eye protection. Hammering
operations cause chips to fly. Flying particles can cause permanent
eye damage. Wear a dust mask or respirator for applications that
generate dust. Ear protection may be required for mostapplications.
Keep a firm grip on the tool at all times. Do not attempt
to operate this tool without holding it with both hands.
Operating this tool with one hand will result in loss of control.
Breaking through or encountering hard materials such as re-bar
may be hazardous aswell.
• Do not operate this tool for long periods of time. Vibration
caused by hammer action may be harmful to your hands and arms.
Use gloves to provide extra cushion and limit exposure by taking
frequent restperiods.
• Do not recondition bits yourself. Chisel reconditioning should
be done by an authorized specialist. Improperly reconditioned
chisels could causeinjury.
Accessories and tool may get hot during operation.
Wear gloves when handling them if performing heat producing
applications such as hammerdrilling and drillingmetals.
Never lay the tool down until the bit has come to a complete
stop. Moving bits could causeinjury.
Do not strike jammed bits with a hammer to dislodge
them. Fragments of metal or material chips could dislodge and
causeinjury.
Slightly worn chisels can be resharpened bygrinding.
Do not overheat the bit (discoloration) while grinding a new
edge. Badly worn chisels require reforging. Do not reharden and
temper thechisel.
Air vents often cover moving parts and should be avoided.
Loose clothes, jewelry or long hair can be caught in movingparts.
c) When battery pack is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or afire.
d) Under abusive conditions, liquid may be ejected from
the battery; avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause
irritation orburns.
6) SERVICE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This will
ensure that the safety of the power tool ismaintained.
Additional Safety Instructions for Rotary
Hammers
Wear ear protectors. Exposure to noise can cause hearingloss.
Use auxiliary handle(s), if supplied with the tool. Loss of
control can cause personalinjury.
Hold power tool by insulated gripping surfaces, when
performing an operation where the cutting accessory may
contact hidden wiring. Cutting accessory contacting a “live” wire
may make exposed metal parts of the power tool “live” and could
give the operator an electricshock.
Be certain that the material being drilled does not conceal
electric or gas service and that their locations have been
verified with the utilitycompanies.
Use clamps or other practical way to secure and support
the workpiece to a stable platform. Holding the work by hand
or against your body is unstable and may lead to loss ofcontrol.
4
English
WARNING: ALWAYS wear proper personal hearing protection
that conforms to ANSI S12.6 (S3.19) during use. Under some
conditions and duration of use, noise from this product may
contribute to hearingloss.
WARNING: ALWAYS use eye protection. All users and
bystanders must wear eye protection that conforms to ANSI Z87.1.
CAUTION: When not in use, place tool on its side on a stable
surface where it will not cause a tripping or falling hazard.
Some tools with large battery packs will stand upright on the battery
pack but may be easily knockedover.
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V ...................volts A ...................... amperes
Hz ................. hertz W ..................... watts
min ............... minutes or AC ..........alternating
or DC ... direct current current
................. Class I Construction or AC/DC ... alternating
(grounded) ........................or direct
................. Class II Construction current
(double insulated) no ....................no load
…/min .......... per minute speed
BPM ............. beats per minute n ......................rated
IPM ............... impacts per minute ........................speed
RPM ............. revolutions per .....................earthing
minute terminal
sfpm ............. surface feet ..................... safety alert
..................... per minute symbol
SPM .............strokes per minute ....................visible
..................... .........................radiation
WARNING: ALWAYS use safety glasses. Everyday eyeglasses are
NOT safety glasses. Also use face or dust mask if cutting operation
is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
ANSI Z87.1 eye protection (CAN/CSA Z94.3),
ANSI S12.6 (S3.19) hearing protection,
NIOSH/OSHA/MSHA respiratoryprotection.
WARNING: Some dust created by power sanding, sawing,
grinding, drilling, and other construction activities contains chemicals
known to the State of California to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
lead from lead-based paints,
crystalline silica from bricks and cement and other masonry
products, and
arsenic and chromium from chemically-treatedlumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety
equipment, such as those dust masks that are specially designed to
filter out microscopicparticles.
Avoid prolonged contact with dust from power sanding,
sawing, grinding, drilling, and other construction activities.
Wear protective clothing and wash exposed areas with soap
and water. Allowing dust to get into your mouth, eyes, or lay on
the skin may promote absorption of harmfulchemicals.
WARNING: Use of this tool can generate and/or disperse dust,
which may cause serious and permanent respiratory or other injury.
Always use NIOSH/OSHA approved respiratory protection
appropriate for the dust exposure. Direct particles away from face
andbody.
5
English
blow, been dropped, run over or damaged in any way (e.g., pierced
with a nail, hit with a hammer, stepped on). Damaged battery packs
should be returned to the service center forrecycling.
WARNING: Fire hazard. Do not store or carry the battery pack
so that metal objects can contact exposed battery terminals.
For example, do not place the battery pack in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with loose nails, screws,
keys, etc. Transporting batteries can possibly cause fires if the
battery terminals inadvertently come in contact with conductive
materials such as keys, coins, hand tools and the like. The US
Department of Transportation Hazardous Material Regulations (HMR)
actually prohibit transporting batteries in commerce or on airplanes
(e.g., packed in suitcases and carry-on luggage) UNLESS they are
properly protected from short circuits. So when transporting individual
battery packs, make sure that the battery terminals are protected and
well insulated from materials that could contact them and cause a
shortcircuit.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)
Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
lithium ion battery packs areburned.
If battery contents come into contact with the skin,
immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for 15
minutes or until irritation ceases. If medical attention is needed,
the battery electrolyte is composed of a mixture of liquid organic
carbonates and lithiumsalts.
Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek
medicalattention.
WARNING: Burn hazard. Battery liquid may be flammable if
exposed to spark orflame.
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to include the
catalog number and voltage. Consult the chart at the end of this
manual for compatibility of chargers and batterypacks.
The battery pack is not fully charged out of the carton. Before using
the battery pack and charger, read the safety instructions below and
then follow charging proceduresoutlined.
READ ALL INSTRUCTIONS
Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable liquids,
gases or dust. Inserting or removing the battery pack from the
charger may ignite the dust orfumes.
NEVER force the battery pack into the charger. Do not
modify the battery pack in any way to fit into a non-
compatible charger as battery pack may rupture causing
serious personal injury. Consult the chart at the end of this
manual for compatibility of batteries andchargers.
Charge the battery packs only in designated
DEWALT
chargers.
DO NOT splash or immerse in water or otherliquids.
Do not store or use the tool and battery pack in locations
where the temperature may reach or exceed 104°F (40°C)
(such as outside sheds or metal buildings in summer). For
best life store battery packs in a cool, drylocation.
NOTE: Do not store the battery packs in a tool with the
trigger switch locked on. Never tape the trigger switch in the
ONposition.
WARNING: Fire hazard. Never attempt to open the battery pack
for any reason. If the battery pack case is cracked or damaged, do
not insert into the charger. Do not crush, drop or damage the battery
pack. Do not use a battery pack or charger that has received a sharp
6
English
NOTICE: Under certain conditions, with the charger plugged into the
power supply, the charger can be shorted by foreign material. Foreign
materials of a conductive nature, such as, but not limited to, grinding
dust, metal chips, steel wool, aluminum foil or any buildup of metallic
particles should be kept away from the charger cavities. Always unplug
the charger from the power supply when there is no battery pack in the
cavity. Unplug the charger before attempting toclean.
DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger and
battery pack are specifically designed to worktogether.
These chargers are not intended for any uses other than
charging
DEWALT
rechargeable batteries. Any other uses may
result in risk of fire, electric shock orelectrocution.
Do not expose the charger to rain orsnow.
Pull by the plug rather than the cord when disconnecting
the charger. This will reduce the risk of damage to the electric plug
andcord.
Make sure that the cord is located so that it will not be
stepped on, tripped over or otherwise subjected to damage
orstress.
Do not use an extension cord unless it is absolutely
necessary. Use of improper extension cord could result in risk of
fire, electric shock orelectrocution.
When operating a charger outdoors, always provide a dry
location and use an extension cord suitable for outdoor
use. Use of a cord suitable for outdoor use reduces the risk of
electricshock.
An extension cord must have adequate wire size (AWG
or American Wire Gauge) for safety. The smaller the gauge
number of the wire, the greater the capacity of the cable, that is,
16 gauge has more capacity than 18 gauge. An undersized cord
will cause a drop in line voltage resulting in loss of power and
The RBRC® Seal
The RBRC® (Rechargeable Battery Recycling
Corp oration) Seal on the nickel cadmium, nickel metal
hydride or lithium-ionbatteries (or battery packs)
indicates that the costs to recycle these batteries (or
battery packs) at the end of their useful life have already
been paid by D
E
WALT. In some areas, it is illegal to place
spent nickel cadmium, nickel metal hydride or lithium-ion batteries in
the trash or municipal solid waste stream and the Call 2 Recycle®
program provides an environmentally conscious alternative.
Call 2 Recycle, Inc., in cooperation with D
E
WALT and other battery
users, has established the program in the United States and Canada
to facilitate the collection of spent nickel cadmium, nickel metal hydride
or lithium-ion batteries. Help protect our environment and conserve
natural resources by returning the spent nickel cadmium, nickel metal
hydride or lithium-ion batteries to an authorized D
E
WALT service
center or to your local retailer for recycling. You may also contact your
local recycling center for information on where to drop off the spent
battery. RBRC® is a registered trademark of Call 2 Recycle, Inc.
Important Safety Instructions for All
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for batterychargers.
Before using the charger, read all instructions and cautionary
markings on the charger, battery pack and product using the
batterypack.
WARNING: Shock hazard. Do not allow any liquid to get inside the
charger. Electric shock mayresult.
CAUTION: Burn hazard. To reduce the risk of injury, charge only
DEWALT
rechargeable battery packs. Other types of batteries may
overheat and burst resulting in personal injury and propertydamage.
7
English
The charger is designed to operate on standard 120V
household electrical power. Do not attempt to use it on any
other voltage. This does not apply to the vehicularcharger.
Chargers
Your tool uses a
DEWALT
charger. Be sure to read all safety instructions
before using your charger. Consult the chart at the end of this manual
for compatibility of chargers and batterypacks.
Charging Procedure (Fig. 1)
1. Plug the charger into an appropriate outlet
before inserting the batterypack.
2. Insert the battery pack (G) into the charger,
as shown in Figure 1, making sure the pack
is fully seated in charger. The red (charging)
light will blink continuously, indicating that
the charging process hasstarted.
3. The completion of charge will be indicated
by the red light remaining ON continuously.
The pack is fully charged and may be used
at this time or left in thecharger.
Indicator Light Operation
DCB101, DCB102, DCB103
PACK CHARGING
PACK CHARGED
x
HOT/COLD DELAY
PROBLEM PACK OR CHARGER
FIG. 1
G
overheating. When using more than one extension to make up the
total length, be sure each individual extension contains at least the
minimum wire size. The following table shows the correct size to
use depending on cord length and nameplate ampere rating. If in
doubt, use the next heavier gauge. The lower the gauge number,
the heavier thecord.
Minimum Gauge for Cord Sets
Ampere Rating
Volts Total Length of Cord in Feet (meters)
120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)
240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)
More
Than
Not More
Than AWG
0 6 18 16 16 14
610 18 16 14 12
10 12 16 16 14 12
12 16 14 12 Not Recommended
Do not place any object on top of the charger or place the
charger on a soft surface that might block the ventilation
slots and result in excessive internal heat. Place the charger
in a position away from any heat source. The charger is ventilated
through slots in the top and the bottom of thehousing.
Do not operate the charger with a damaged cord orplug.
Do not operate the charger if it has received a sharp blow,
been dropped or otherwise damaged in any way. Take it to an
authorized servicecenter.
Do not disassemble the charger; take it to an authorized
service center when service or repair is required. Incorrect
reassembly may result in a risk of electric shock, electrocution orfire.
Disconnect the charger from the outlet before attempting
any cleaning. This will reduce the risk of electric shock.
Removing the battery pack will not reduce thisrisk.
NEVER attempt to connect 2 chargerstogether.
8
English
Once the battery has reached an optimum temperature, the yellow
light will turn off and the charger will automatically resume the charging
procedure. This feature ensures maximum battery life.
LEAVING THE BATTERY PACK IN THE CHARGER
The charger and battery pack can be left connected with the charge
indicator showing Pack Charged.
WEAK BATTERY PACKS: Weak batteries will continue to function
but should not be expected to perform as much work.
FAULTY BATTERY PACKS
DCB101, DCB102, DCB103
These chargers will not charge a faulty battery pack. The charger will
indicate faulty battery pack by refusing to light or by displaying problem
pack or charger.
NOTE: This could also mean a problem with a charger.
DCB107, DCB112, DCB113, DCB115
These chargers will not charge a faulty battery pack. The charger will
indicate faulty battery pack by refusing to light.
NOTE: This could also mean a problem with a charger.
Wall Mounting
DCB107, DCB112, DCB113, DCB115
These chargers are designed to be wall mountable or to sit upright on
a table or work surface.
If wall mounting, locate the charger within reach of an electrical outlet.
Mount the charger securely using drywall screws at least 1" (25.4 mm)
long, screwed into wood to an optimal depth leaving approximately
7/32" (5.5 mm) of the screw exposed.
Important Charging Notes
1. Longest life and best performance can be obtained if the battery
pack is charged when the air temperature is between 65 °F
DCB107, DCB112, DCB113, DCB115
PACK CHARGING
PACK CHARGED
HOT/COLD DELAY
Charge Indicators
This charger is designed to detect certain problems that can arise.
Problems are indicated by the red light flashing at a fast rate. If this
occurs, re-insert the battery pack into the charger. If the problem
persists, try a different battery pack to determine if the charger is
working properly. If the new pack charges correctly, then the original
pack is defective and should be returned to a service center or other
collection site for recycling. If the new battery pack elicits the same
trouble indication as the original, have the charger and the battery pack
tested at an authorized service center.
HOT/COLD DELAY
DCB101, DCB102, DCB103
These chargers have a hot/cold delay feature. When the charger
detects a battery that is too hot or too cold, it automatically starts a
delay, suspending charging. The red light flashes long, then short while
in the hot/cold delay mode.
Once the battery has reached an optimum temperature, the charger
will automatically resume the charging procedure. This feature ensures
maximum battery life.
DCB107, DCB112, DCB113, DCB115
These chargers have a hot/cold delay feature. When the charger
detects a battery that is too hot or too cold, it automatically starts a
delay, suspending charging. The red light will continue to blink, but a
yellow indicator light will be illuminated during this suspension.
9
English
there is no battery pack in the cavity. Unplug the charger before
attempting toclean.
7. Do not freeze or immerse the charger in water or any otherliquid.
WARNING: Shock hazard. Don’t allow any liquid to get inside the
charger. Electric shock mayresult.
WARNING: Burn hazard. Do not submerge the battery pack in any
liquid or allow any liquid to enter the battery pack. Never attempt to
open the battery pack for any reason. If the plastic housing of the
battery pack breaks or cracks, return to a service center forrecycling.
Storage Recommendations
1. The best storage place is one that is cool and dry, away from direct
sunlight and excess heat orcold.
2. For long storage, it is recommended to store a fully charged battery
pack in a cool dry place out of the charger for optimalresults.
NOTE: Battery packs should not be stored completely depleted of
charge. The battery pack will need to be recharged beforeuse.
SAVE THESE INSTRUCTIONS
FOR FUTURE USE
COMPONENTS (Fig. 2)
WARNING: Never modify the power tool or any part of it. Damage
or personal injury couldresult.
A. Side handle
B. Trigger switch
C. Forward/reverse control
button (Lock-off button)
D. Mode selector
E. Main handle
F. Worklight
G. Battery pack
H. Battery release button
I. SHOCKS - Active Vibration
control
J. Utility hook
and 75 °F (18 ° 24 °C). DO NOT charge the battery pack in
an airtemperature below +40 °F (+4.5 °C), or above +104 °F
(+40°C). This is important and will prevent serious damage to the
batterypack.
2. The charger and battery pack may become warm to the touch
while charging. This is a normal condition, and does not indicate
a problem. To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm environment
such as in a metal shed or an uninsulatedtrailer.
3. A cold battery pack will charge at about half the rate of a warm
battery pack. The battery pack will charge at that slower rate
throughout the entire charging cycle and will not return to
maximum charge rate even if the battery packwarms.
4. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp or other
appliance;
b. Check to see if receptacle is connected to a light switch which
turns power off when you turn out the lights;
c. Move the charger and battery pack to a location where the
surrounding air temperature is approximately 65 °F 75 °F
(18° – 24 °C);
d. If charging problems persist, take the tool, battery pack and
charger to your local servicecenter.
5. The battery pack should be recharged when it fails to produce
sufficient power on jobs which were easily done previously. DO
NOT CONTINUE to use under these conditions. Follow the
charging procedure. You may also charge a partially used pack
whenever you desire with no adverse effect on the batterypack.
6. Foreign materials of a conductive nature such as, but not limited
to, grinding dust, metal chips, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from charger
cavities. Always unplug the charger from the power supply when
10
English
Side Handle (Fig. 2)
WARNING: To reduce the risk of personal injury, ALWAYS operate
the tool with the side handle (A) properly installed. Failure to do so may
result in the side handle slipping during tool operation and subsequent
loss of control. Hold tool with both hands to maximizecontrol.
The side handle (A) clamps to the front barrel (collar) and may be
rotated 360° to permit right-or left-hand use. The side handle can
be tightened by rotating the black plastic portion of the side handle
clockwise. The side handle must be tightened sufficiently to resist the
twisting action of the tool if the accessory binds or stalls. Be sure to
grip the side handle at the far end to control the tool during a stall. To
loosen side handle, rotatecounterclockwise.
Trigger Switch (Fig. 2)
To turn the tool on, squeeze the trigger switch (B). To turn the tool
off, release the trigger switch. Your tool is equipped with a brake. The
chuck will stop as soon as the trigger switch is fullyreleased.
VARIABLE SPEED TRIGGER SWITCH
The variable speed trigger switch enables you to select the best speed
for a particular application. The farther you squeeze the trigger switch,
the faster the tool will operate. For maximum tool life, use variable
speed only for starting holes orfasteners.
NOTE: Continuous use in variable speed range is not recommended.
It may damage the trigger switch and should beavoided.
Utility Hook (Fig. 3)
A utility hook is fitted to the left side of the tool. To extend the utility
hook pull it out from the side of the tool. To store the utility hook push
it back flush with the side of thetool. The utility hook (J) and can be
positioned to the left or right of the tool to accommodate left or right-
handedusers.
INTENDED USE
These heavy-duty cordless rotary hammers are designed for
professional concrete drilling and chiselingapplications.
DO NOT use under wet conditions or in presence of flammable liquids
orgases.
These heavy-duty cordless rotary hammers are professional power
tools. DO NOT let children come into contact with the tool. Supervision
is required when inexperienced operators use thistool.
FIG. 2
B
D
C
E
A
J
F
G
H
I
11
English
Mode Selector (Fig. 4)
CAUTION: Do not change to drill or hammerdrill mode with a chisel
bit in the chuck. Personal injury and damage to tool mayresult.
CAUTION: Never change the mode while the unit isrunning.
For straight drilling, rotate the mode
selector (D) until the arrow points to the drill
bit symbol (J). For rotary hammer mode,
align the arrow with the rotary hammer
symbol (K). For chipping mode, align arrow
with the chipping symbol (L).
NOTE: The mode selector (D) must be
in drill, hammer or chipping mode at all
times. There are no operable positions
inbetween.
Forward/Reverse Control Button (Fig. 2, 5)
A forward/reverse control button (C) determines the direction of bit
rotation and also serves as a lock-offbutton.
To select forward rotation, release the trigger switch (B) and depress
the forward/reverse control button on the right side of thetool.
To select reverse, depress the forward/reverse control button on the
left side of thetool.
The center position of the control button locks the tool in the
off position. When changing the position of the control button, be
sure the trigger isreleased.
NOTE: The first time the tool is run after changing the direction of
rotation, you may hear a click on start up. This is normal and does not
indicate aproblem.
FIG. 4
D
J
K
L
1. Position the utility hook into the extended position and remove the
hex headscrew.
2. Pull out the utility hook (J) until it is free fromunit.
3. Reinsert the utility hook into the desired side and push it into theslot.
NOTE: On some models the slot may be covered with a sticker.
Either remove the sticker or pierce the sticker to expose the
slotunderneath.
4. Re-insert the hex screw and tightensecurely.
If use of the hook is not desired at all, it can be removedcompletely.
J
FIG. 3
12
English
WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the side handle properly installed and
securely tightened. Failure to do so may result in the side handle
slipping during tool operation and subsequent loss of control. Hold
tool with both hands to maximizecontrol.
Installing and Removing the Battery Pack
(Fig. 7)
WARNING: To reduce the risk of injury, never depress the battery
release button without removing the battery pack. Depressing the
battery release button without removing the battery pack can result
in the battery pack falling outunexpectedly.
NOTE: For best results, make sure your battery pack is fullycharged.
To install the battery pack (G) into the tool handle, align the battery
pack with the rails inside the tool’s handle and slide it into the handle
until the battery pack is firmly seated in the tool and ensure that it does
notdisengage.
G
FIG. 7
H
To remove the battery pack from the tool, press the release button (H)
and firmly pull the battery pack out of the tool handle. Insert it into the
charger as described in the charger section of thismanual.
FIG. 5
C
LOCKED UNLOCKED,
REVERSE
UNLOCKED,
FORWARD
Worklight (Fig. 6)
CAUTION: Do not stare into worklight. Serious eye injury could
result.
There is a worklight (F) located on the front FIG. 6
F
of the tool. The worklight is activated
when the trigger switch is depressed, and
will automatically turn off 20 seconds after
the trigger switch is released. If the trigger
switch remains depressed, the worklight
will remainon.
NOTE: The worklight is for lighting the
immediate work surface and is not intended to be used as aflashlight.
OPERATION
WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect tool from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can causeinjury.
WARNING: To reduce the risk of personal injury, ALWAYS
ensure workpiece is anchored or clamped firmly. If drilling thin
material, use a wood "back-up" block to prevent damage to
thematerial.
13
English
NOTE: The fuel gauge is only an indication of the charge left on the
battery pack. It does not indicate tool functionality and is subject to
variation based on product components, temperature and end-user
application.
For more information regarding fuel gauge battery packs, please
contact call 1-800-4-D
E
WALT (1-800-433-9258) or visit our website
www.dewalt.com.
Shocks – Active Vibration Control (Fig. 2)
For best vibration control, hold the tool with one hand on the main
handle (E) and the other hand on the side handle (A). Apply just enough
pressure so the SHOCKS (I) in the rear handle are halfway depressed.
The hammer only needs enough pressure to engage the internal active
vibration control. Applying too much pressure will not make the tool drill
faster and active vibration control will notengage.
SDS Chuck (Fig. 9)
WARNING: Burn Hazard. ALWAYS wear gloves when changing
bits. Accessible metal parts on the tool and bits may get extremely
hot during operation. Small bits of broken material may damage
barehands.
To insert bit, insert shank of bit about
3/4"(19 mm) into chuck (N). Push and
rotate bit until it locks in place. The bit will
be securelyheld.
To release bit, pull the sleeve (O) back
and remove thebit.
Proper Hand Position
(Fig. 10)
WARNING: To reduce the risk of serious personal injury, ALWAYS
use proper hand position asshown.
FIG. 9
O
N
NOTE: Operating temperature of this tool is 19° to 104°F (-7° to
+40°C). Using the tool outside of this temperature range will decrease
the life of thetool.
FUEL GAUGE BATTERY PACKS (FIG. 8)
Some D
E
WALT battery packs include a fuel gauge which consists of
three green LED lights that indicate the level of charge remaining in
the battery pack.
The fuel gauge is an indication of approximate levels of charge
remaining in the battery pack according to the following
indicators:
75–100% charged
51–74% charged
< 50% charged
Pack needs to be charged
To actuate the fuel gauge, press and
M
FIG. 8
hold the fuel gauge button (M). A
combination of the three green LED
lights will illuminate designating the level
of charge left. When the level of charge
in the battery is below the usable limit,
the fuel gauge will not illuminate and the
battery will need to be recharged.
14
English
WARNING: To reduce the risk of serious personal injury, ALWAYS
hold securely in anticipation of a suddenreaction.
Proper hand position requires one hand on the side handle, with the
other hand on the mainhandle.
FIG. 10
Drilling (Fig. 4)
WARNING: To reduce the risk of personal injury, ALWAYS operate
the tool with the side handle properly installed. Failure to do so may
result in the side handle slipping during tool operation and subsequent
loss of control. Hold tool with both hands to maximizecontrol.
NOTICE: If drilling thin material, use a wood “back-up” block to
prevent damage to thematerial.
1. Turn the mode selector (D) to the drill symbol (J).
2. Use sharp drill bits only. For WOOD, use twist bits, spade bits,
power auger bits or hole saws. For METAL, use high-speed steel
twist drill bits or hole saws. Use a cutting lubricant when drilling
metals. The exceptions are cast iron and brass which should be
drilled dry. For MASONRY, such as brick, cement, cinder block,
etc., use carbide-tipped bits rated for percussiondrilling.
3. Always apply pressure in a straight line with the bit. Use enough
pressure to keep drill biting, but do not push hard enough to stall
the motor or deflect thebit.
4. Hold tool firmly with both hands to control the twisting action of
the drill. If model is not equipped with side handle, grip drill with one
hand on the handle and one hand on the batterypack.
WARNING: Drill may stall if overloaded causing a sudden twist.
Always expect the stall. Grip the drill firmly to control the twisting
action and avoidinjury.
5. IF DRILL STALLS, it is usually because it is being overloaded
or improperly used. RELEASE TRIGGER IMMEDIATELY,
remove drill bit from work, and determine cause of stalling. DO
NOT DEPRESS TRIGGER ON AND OFF IN AN ATTEMPT
TO START A STALLED DRILL — THIS CAN DAMAGE
THEDRILL.
6. To minimize stalling or breaking through the material, reduce
pressure on drill and ease the bit through the last fractional part of
thehole.
7
. Keep the motor running when pulling the bit back out of a drilled
hole. This will help preventjamming.
8
. With variable speed drills there is no need to center punch
the point to be drilled. Use a slow speed to start the hole and
accelerate by squeezing the trigger harder when the hole is deep
enough to drill without the bit skippingout.
DRILLING IN METAL
An SDS Plus to round shank adaptor chuck is required. Ensure that
tool is in drill-only mode. Start drilling with slow speed and increase to
full power while applying firm pressure on the tool. A smooth even flow
of metal chips indicates the proper drilling rate. Use a cutting lubricant
when drilling metals. The exceptions are cast iron and brass which
should be drilleddry.
15
English
NOTE: Large (5/16" to 1/2" [7.9 mm to 12.7 mm]) holes in steel can
be made easier if a pilot hole (5/32" to 3/16" [4 mm to 4.8 mm]) is
drilledfirst.
DRILLING IN WOOD
An SDS Plus to round shank adaptor chuck is required. Ensure that tool
is in drill-only mode. Start drilling with slow speed and increase to full
power while applying firm pressure on the tool. Holes in wood can be
made with the same twist drills used for metal. These bits may overheat
unless pulled out frequently to clear chips from the flutes. For larger
holes, use spade bits, power auger bits, or hole saws. Work that is apt
to splinter should be backed up with a block ofwood.
DRILLING IN MASONRY
When drilling in masonry, use carbide-tipped bits rated for percussion
drilling and be certain that the bits are sharp. Use a constant and firm
force on the tool to drill most effectively. A smooth, even flow of dust
indicates the proper drillingrate.
HAMMERDRILL OPERATION (FIG. 4)
1. Turn the mode selector (D) to the rotary hammer symbol (K).
2. When drilling, use just enough force on the hammer to keep it from
bouncing excessively or “rising” off the bit. Too much force will
cause slower drilling speeds, overheating, and a lower drillingrate.
3. Drill straight, keeping the bit at a right angle to the work. Do not
exert side pressure on the bit when drilling as this will cause
clogging of the bit flutes and a slower drillingspeed.
4. When drilling deep holes, if the hammer speed starts to drop off,
pull the bit partially out of the hole with the tool still running to help
clear debris from thehole.
5. For masonry, use carbide-tipped bits or masonry bits. A smooth
even flow of dust indicates the proper drillingrate.
Chipping and Chiselling (Fig. 4)
1. Set the mode selector switch (D) to the chipping symbol (L).
2. Insert the appropriate chisel and rotate it by hand to lock it into one
of 51positions.
3. Adjust the side handle (A) asrequired.
4. Switch on the tool and startworking.
5. Always switch off the tool when work is finished and
beforeunplugging.
MAINTENANCE
WARNING: To reduce the risk of serious personal injury, turn
tool off and disconnect tool from power source before making
any adjustments or removing/installing attachments or
accessories. An accidental start-up can causeinjury.
Cleaning
WARNING: Blow dirt and dust out of all air vents with clean, dry
air at least once a week. To minimize the risk of eye injury, always
wear ANSI Z87.1 approved eye protection and proper NIOSH/
OSHA/MSHA respiratory protection when performingthis.
WARNING: Never use solvents or other harsh chemicals for
cleaning the non-metallic parts of the tool. These chemicals may
weaken the plastic materials used in these parts. Use a cloth
dampened only with water and mild soap. Never let any liquid get
inside the tool; never immerse any part of the tool into aliquid.
CHARGER CLEANING INSTRUCTIONS
WARNING: Shock hazard. Disconnect the charger from the AC
outlet before cleaning. Dirt and grease may be removed from the
exterior of the charger using a cloth or soft non-metallic brush. Do not
use water or any cleaningsolutions.
16
English
Accessories
WARNING: Since accessories, other than those offered by
DEWALT
, have not been tested with this product, use of such
accessories with this tool could be hazardous. To reduce the risk of
injury, only
DEWALT
recommended accessories should be used with
thisproduct.
The D25303DH is available, at extra cost, for active dust extraction
during hammer/drillingoperation.
Recommended accessories for use with your tool are available
at extra cost from your local dealer or authorized service center.
If you need assistance in locating any accessory, please contact
DEWALT
Industrial Tool Co., 701 East Joppa Road, Towson, MD
21286, call 1-800-4-
DEWALT
(1-800-433-9258) or visit our website:
www.
DEWALT
.com.
MAXIMUM RECOMMENDED CAPACITIES
RPM 0–1,100 min-1
BPM 0–4,600 min-1
Bits, Masonry Drilling 1" (25.4 mm)
Repairs
The charger and battery pack are notserviceable.
To assure product SAFETY and RELIABILITY, repairs, maintenance and
adjustment (including brush inspection and replacement) should be
performed by a
DEWALT
factory service center, a
DEWALT
authorized
service center or other qualified service personnel. Always use
identical replacementparts.
Register Online
Thank you for your purchase. Register your product now for:
WARRANTY SERVICE: Registering your product will help you
obtain more efficient warranty service in case there is a problem
with yourproduct.
CONFIRMATION OF OWNERSHIP: In case of an insurance
loss, such as fire, flood or theft, your registration of ownership will
serve as your proof ofpurchase.
FOR YOUR SAFETY: Registering your product will allow us to
contact you in the unlikely event a safety notification is required
under the Federal Consumer SafetyAct.
Register online at www.
DEWALT
.com/register.
Three Year Limited Warranty
DEWALT
will repair, without charge, any defects due to faulty materials
or workmanship for three years from the date of purchase. This
warranty does not cover part failure due to normal wear or tool abuse.
For further detail of warranty coverage and warranty repair information,
visit www.
DEWALT
.com or call 1-800-4-
DEWALT
(1-800-433-9258).
This warranty does not apply to accessories or damage caused where
repairs have been made or attempted by others. This warranty gives
you specific legal rights and you may have other rights which vary in
certain states orprovinces.
In addition to the warranty,
DEWALT
tools are covered by our:
2 YEARS FREE SERVICE
DCH253, DCH273
DEWALT
will maintain the tool and replace worn parts caused by
normal use, for free, any time during the first two years afterpurchase.
2 YEARS FREE SERVICE ON D
E
WALT BATTERY PACKS
DC9071, DC9091, DC9096, DC9280, DC9360, DC9180,
DCB120, DCB127, DCB201, DCB203, DCB203BT, DCB207
17
English
3 YEARS FREE SERVICE ON D
E
WALT BATTERY PACKS
DCB200, DCB204, DCB204BT, DCB205
DEWALT
BATTERY PACKS
Product warranty voided if the battery pack is tampered with in any
way.
DEWALT
is not responsible for any injury caused by tampering
and may prosecute warranty fraud to the fullest extent permitted
bylaw.
90 DAY MONEY BACK GUARANTEE
If you are not completely satisfied with the performance of your
DEWALT
Power Tool, Laser, or Nailer for any reason, you can return it
within 90 days from the date of purchase with a receipt for a full refund
– no questionsasked.
LATIN AMERICA: This warranty does not apply to products sold
in Latin America. For products sold in Latin America, see country
specific warranty information contained in the packaging, call the local
company or see website for warrantyinformation.
FREE WARNING LABEL REPLACEMENT:
If your warning labels become illegible or are missing, call
1-800-4-
DEWALT
(1-800-433-9258) for a freereplacement.
XXX
Français
18
Définitions: lignes directrices en
matière de sécurité
Les définitions ci-dessous décrivent le niveau de danger pour
chaque mot-indicateur employé. Lire le mode d’emploi et porter
une attention particulière à cessymboles.
DANGER: indique une situation dangereuse imminente qui, si
elle n’est pas évitée, entraînera la mort ou des
blessuresgraves.
AVERTISSEMENT : indique une situation potentiellement
dangereuse qui, si elle n’est pas évitée, pourrait entraîner la
mort ou des blessuresgraves.
ATTENTION : indique une situation potentiellement
dangereuse qui, si elle n’est pas évitée, pourrait entraîner des
blessures légères oumodérées.
AVIS : indique une pratique ne posant aucun risque de
dommages corporels mais qui par contre, si rien n’est fait pour
l’éviter, pourrait poser des risques de dommagesmatériels.
POUR TOUTE QUESTION OU REMARQUE AU SUJET DE CET OUTIL
OU DE TOUT AUTRE OUTIL D
EWALT
, COMPOSEZ LE NUMÉRO
SANS FRAIS : 1-800-4-
DEWALT
(1-800-433-9258).
AVERTISSEMENT : afin de réduire le risque de blessures, lire
le mode d’emploi de l’outil.
Avertissements de sécurité généraux pour
les outils électriques
AVERTISSEMENT! Lire toutes les directives et toutes les
consignes de sécurité. Le non-respect des avertissements
et des directives pourrait se solder par un choc électrique, un
incendie et/ou une blessuregrave.
CONSERVER TOUS LES AVERTISSEMENTS
ET TOUTES LES DIRECTIVES POUR UN
USAGE ULTÉRIEUR
Le terme « outil électrique » cité dans les avertissements se rapporte
à votre outil électrique à alimentation sur secteur (avec fil) ou par piles
(sans fil).
1) SÉCURITÉ DU LIEU DE TRAVAIL
a) Tenir l’aire de travail propre et bien éclairée. Les lieux
encombrés ou sombres sont propices auxaccidents.
b) Ne pas faire fonctionner d’outils électriques dans un
milieu déflagrant, tel qu’en présence de liquides, de
gaz ou de poussières inflammables. Les outils électriques
produisent des étincelles qui pourraient enflammer la poussière
ou lesvapeurs.
c) Éloigner les enfants et les personnes à proximité pendant
l’utilisation d’un outil électrique. Une distraction pourrait en
faire perdre la maîtrise à l’utilisateur.
2) SÉCURITÉ EN MATIÈRE D’ÉLECTRICITÉ
a) Les fiches des outils électriques doivent correspondre
à la prise. Ne jamais modifier la fiche d’aucune façon.
Ne jamais utiliser de fiche d’adaptation avec un outil
électrique mis à la terre. Le risque de choc électrique sera
réduit par l’utilisation de fiches non modifiées correspondant à
laprise.
b) Éviter tout contact physique avec des surfaces mises à la
terre comme des tuyaux, des radiateurs, des cuisinières
et des réfrigérateurs. Le risque de choc électrique est plus
élevé si votre corps est mis à laterre.
c) Ne pas exposer les outils électriques à la pluie ou à
l’humidité. La pénétration de l’eau dans un outil électrique
augmente le risque de chocélectrique.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

DeWalt DCH253 Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues