How To Install and Use The
Female AUI
Transceiver
Module
3C12060
1 Interworking Information
The 3Com
®
Female AUI Transceiver
Module has been designed to the IEEE
802.3 specification for an AUI interface
to provide external transceiver
connectivity.
The Transceiver Module provides an
extra port or connectivity to another
medium on the following
LinkBuilder
®
products:
• ECS modules (3C12076 and
3C12050/1)
• MSH modules (3C18110, 3C18120,
3C18124, 3C18146 and 3C18600)
• FMS Stackable Hubs (3C16250,
3C16265, 3C16271 and 3C16371)
• FMS II Stackable Hubs (3C16665,
3C16670 and 3C16671)
• Repeaters (3C16170, 3C16200,
3C16210 and 3C16505)
This product has the benefit of a
"lifetime warranty": see page 4.
2 Installation
Only qualified personnel
should install this device.
Observe anti-static
precautions! Use an earthed
wrist-band!
The Transceiver Module provides a
15-pin female AUI connector (acting as
a DTE port) at the external interface
end. A 16-pin header and a 16-way
edge connector are mounted at the
other end of the Transceiver Module
for connection to a Module, Stackable
Hub or Repeater.
The Transceiver Module is connected
to an external transceiver directly or
with an AUI cable (transceiver cable or
drop cable) with a maximum length of
50 metres (although in most cases 3
metres should be sufficient).
The Transceiver Module will enable
the Module, Stackable Hub or
Repeater to connect to a variety of
transmission medium such as a fiber,
UTP, STP or Thin Ethernet.
Example
Figure 1
Edge connector
Pin header
15-Way
Female
D-connector
External Transceiver
up to 50 m AUI Cabl
e
Female AUI
Transceiver Module
Thin Ethernet Segmen
t
Stackable Hub
This manual provides a general description of the 3Com Female AUI Transceiver Module,
3C12060. Please retain this manual with your other 3Com manuals for future use.
HARDWARE: 3Com Limited ("3Com") warrants its hardware products to be free from defects in workmanship and materials, under
normal use and service, for the following lengths of time from the date of purchase from 3Com or its Authorized Reseller:
Internetworking products One year
Ethernet Stackable Hubs and Unmanaged Ethernet Fixed Port Repeaters Lifetime*
(One Year if not registered)
*Power supply and fans in these stackable hubs and unmanaged repeaters One Year
Other hardware products One year
Spare parts and spares kits 90 days
If a product does not operate as warranted during the applicable warranty period, 3Com shall, at its option and expense, repair the defective
product or part, deliver to Customer an equivalent product or part to replace the defective item, or refund to Customer the purchase price
paid for the defective product. All products that are replaced will become the property of 3Com. Replacement products may be new or
reconditioned. Any replaced or repaired product or part has a ninety (90) day warranty or the remainder of the initial warranty period,
whichever is longer.
3Com shall not be responsible for any software, firmware, information, or memory data of Customer contained in, stored on, or integrated
with any products returned to 3Com pursuant to any warranty.
SOFTWARE: 3Com warrants that the software programs licensed from it will perform in substantial conformance to the program
specifications therefor for a period of ninety (90) days from the date of purchase from 3Com or its Authorized Reseller. 3Com warrants the
magnetic media containing software against failure during the warranty period. No updates are provided. 3Com’s sole obligation hereunder
shall be (at 3Com’s discretion) to refund the purchase price paid by Customer for any defective software products, or to replace any defective
media with software which substantially conforms to 3Com’s applicable published specifications. Customer assumes responsibility for the
selection of the appropriate applications program and associated reference materials. 3Com makes no warranty that its software products
will work in combination with any hardware or applications software products provided by third parties, that the operation of the software
products will be uninterrupted or error free, or that all defects in the software products will be corrected. For any third party products listed
in the 3Com software product documentation or specifications as being compatible, 3Com will make reasonable efforts to provide
compatibility, except where the non-compatibility is caused by a "bug" or defect in the third party’s product.
STANDARD WARRANTY SERVICE: Standard warranty service for hardware products may be obtained by delivering
the defective product, accompanied by a copy of the dated proof of purchase, to 3Com’s Service Center or to an Authorized 3Com Service
Center during the applicable warranty period. Standard warranty service for software products may be obtained by telephoning 3Com’s
Service Center or an Authorized 3Com Service Center, within the warranty period. Products returned to 3Com’s Service Center must be
pre-authorized by 3Com with a Return Material Authorization (RMA) number marked on the outside of the package, and sent prepaid,
insured, and packaged appropriately for safe shipment. The repaired or replaced item will be shipped to Customer, at 3Com’s expense, not
later than thirty (30) days after receipt by 3Com.
WARRANTIES EXCLUSIVE: IF A 3COM PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S
SOLE REMEDY SHALL BE REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT 3COM’S OPTION. THE
FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS,
EXPRESS OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OR
CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. 3COM NEITHER ASSUMES NOR
AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE,
INSTALLATION, MAINTENANCE OR USE OF ITS PRODUCTS.
3COM SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED
DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT,
IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE
OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.
LIMITATION OF LIABILITY. IN NO EVENT, WHETHER BASED IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) SHALL 3COM BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF
ANY KIND, OR FOR LOSS OF REVENUE, LOSS OF BUSINESS, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF ITS PRODUCTS, EVEN
IF 3COM OR ITS AUTHORIZED RESELLER HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NOTHING HEREIN
SHALL HAVE THE EFFECT OF LIMITING OR EXCLUDING 3COM’S LIABILITY FOR DEATH OR PERSONAL INJURY CAUSED BY
NEGLIGENCE.
Some states do not allow the exclusion of implied warranties or the limitation of incidental or consequential damages for consumer products,
so the above limitations and exclusions may not apply to you. This warranty gives you specific legal rights which may vary from state to
state. Nothing in this warranty shall be taken to affect your statutory rights.
GOVERNING LAW: This Limited Warranty shall be governed by the laws of England.
3Com Limited, ISOLAN House, Brindley Way, London Road, Hemel Hempstead, Hertfordshire, HP3 9XJ, UK. 44(0)442 278000
23/12/93
LIMITED WARRANTY
Page 4 Page 1
!
Preparation
Before you install the Transceiver
Module, you must remove the
Module, Hub or Repeater from the
network and all power sources.
Modules must be removed from the
Chassis (you do not need to power
down the Chassis first). The 3C18146
Expansion Module must be separated
from its mother module. See the
relevant User Guide or ‘How to Install
and Use...’ manual.
Remove the blanking plate from the
unit in which you are going to install
the Transceiver Module. The relevant
manual will tell you where to find the
plate.
Keep the blanking plate in a safe place
so that it can be replaced when the
Transceiver Module is removed.
Installing in a Stackable Hub or Repeater
For FMS Stackables and Repeaters,
hold the mounting panel with the pin
header side of the board down.
For FMS II Stackables, hold the
mounting panel with the pin header
side of the board up.
Insert the edge connector end of the
Transceiver Module into the rear of the
mother device.
Slide the Transceiver Module in
carefully to engage in the slot and
push it fully home.
Fix the mounting panel of the Transceiver
Module to the back panel using the two
screws from the blanking plate.
Installing on an ECS or MSH Module
Position the Module on a flat surface
with the 16-way socket facing up.
Hold the Transceiver Module by the
mounting panel and board edge with
the header pins facing down.
Pass the board of the Transceiver
Module through the cut-out in the
front panel.
Align the socket on the Module with
the pins on the Transceiver Module
and push down firmly to connect.
With the 3C18146 Expansion Module,
you align the header and pins and
press gently to engage the pins. Turn
the pair over to rest on the Transceiver
Module and press firmly close to the
header to complete connection.
Fix the mounting panel of the Transceiver
Module to the module using the two
screws from the blanking plate.
Connection
Once the Transceiver Module is
secured in place, attach an external
transceiver, directly or with an AUI
cable. Remember to engage the
slidelocks at both ends of the AUI
cable, if you use one.
3 Operation
Re-install the mother device into its
chassis and/or network and power up.
The Transceiver Module will operate
correctly once power is applied.
4 Problems
If, after installing the Transceiver
Module, no communication is possible,
check the settings of the host unit and
that it is receiving power. If no error is
found, refer to the supplier of your
3Com Female AUI Transceiver Module
for further advice.
Disclaimer
Information in this document is subject to
change without notice and does not represent a
commitment on the part of 3Com. 3Com
reserves the right to revise or change this
document without obligation of 3Com to notify
any person of the revisions or changes.
Information contained in this document is
believed to be accurate at the time of
publication but no liability whatsoever can be
accepted by 3Com arising out of any use of this
information.
3Com and LinkBuilder are registered
trademarks and FMS, FMS II and
MSH are trademarks of the 3Com
Corporation.
Document No: DUA1206-0AAA04
Revision: 00
Issued: August 1994
© 1994 3Com Ireland
Radio Frequency Interference Statement
This equipment has been tested with a class A
computing device and has been found to
comply with part 15 of FCC Rules. Operation in
a residential area may cause unacceptable
interference to radio and TV receptions
requiring the operator to take whatever steps
are necessary to correct the interference.
This digital apparatus does not exceed the Class
A limits for radio noise emissions from digital
apparatus as set out in the interference-causing
equipment standard entitled "Digital
Apparatus", ICES-003 of the Department of
Communications.
Cet appareil numérique respecte les limites de
bruits radioélectriques applicables aux appareils
numériques de Classe A prescrites dans la
norme sur le matériel brouilleur : "Appareils
Numériques", NMB-003 édictée par le ministre
des Communications.
Standards
The 3Com Female AUI Transceiver Module
3C12060 has been designed to conform to the
following standards:
Safety UL 478 CSA 22.2
EN 60950
Environmental IEC 68
R.F.I. FCC Part 15 (Class A)
VDE 0871 Level B
Functional ISO 8802/3, IEEE 802.3
Page 3
Page 2
-
1
-
2
3com 3C12060 Installation And Use
- Taper
- Installation And Use
- Ce manuel convient également à
dans d''autres langues
- English: 3com 3C12060
Documents connexes
-
3com II Hub 10 Manuel utilisateur
-
3com TP TRANSCEIVER INTERFACE MOD Fiche technique
-
-
-
-
-
-
-
-