T740 Quick Start Guide
Aircraft
You are able to shoot multi-angle and high specification photos and create great
content with the aircraft.
Overview
1. Power Button
2. Battery
3. SSD Slot
4. Gimbal Connector
1. Gimbal Release Button
2. Gimbal Lock
3. USB-C Port
(for data transmission)
4. Screw Socket
5. Earphone Jack
6. Auxiliary Bottom Light
7. USB-C Port (for LiDAR module)
8. USB-C Port (for 4G dongle)
Aircraft Modes
Remote Controller
The DJI RC Plus remote controller can transmit a live HD view from the camera of an
aircraft to display on the touchscreen.
1. External RC Antennas
2. Touchscreen
3. Indicator Button
4. Control Sticks
5. Internal Wi-Fi Antennas
6. Back/Function Button
7. L1/L2/L3/R1/R2/R3
Buttons
8. Return to Home (RTH)
Button
9. Microphones
10. Status LED
11. Battery Level LEDs
12. Internal GNSS Antennas
13. Power Button
14. 5D Button
15. Flight Pause Button
16. C3 Button (customizable)
17. Left Dial
18. Record Button
19. Flight Mode Switch
20. Internal RC Antennas
21. microSD Card Slot
22. USB-A Port
23. HDMI Port
24. USB-C Port
25. Focus/Shutter Button
26. Right Dial
27. Scroll Wheel
28. Handle
29. Speaker
30. Air Vent
31. Reserved Mounting Holes
32. C1 Button (customizable)
33. C2 Button (customizable)
34. Rear Cover
35. Battery Release Button
36. WB37 Intelligent Battery
37. Rear Cover Release
Button
38. Alarm
39. Air Intake
40. Dongle Compartment
41. Remote Controller
Strap Bracket
Preparing the Remote Controller
Check battery level: press once.
Power on/off: press and then press and hold.
The remote controller needs to be activated before using for the first time. Follow the
prompts to activate.
Preparing the Aircraft
a. Insert the batteries;
b. Press the power button a minimum of five times. The aircraft will be transformed
to the Landing Mode.
Mount the Gimbal and Camera
a. Press and hold the release button and rotate the gimbal lock counter-clockwise to
remove the gimbal connector cover.
b. Align the white and red dots and insert the gimbal.
c. Rotate the gimbal lock to the locked position.
Installing the SSD
Getting Ready for Takeoff
Linking
a. Power on the remote controller and the aircraft.
b. Open DJI Pilot and follow the on-screen instructions.
Attaching the Propellers
Attach the propellers with marks to the motors with marks and the unmarked
propellers to the motors without marks. Press each propeller down onto the motor
and turn until it is secure.
Flight
Control Stick Mode
The default control stick mode is Mode 2. The left control stick controls the altitude
and heading of the aircraft while the right control stick controls the forward,
backward, and sideward movements.
Manual Takeoff/Landing
1. Start/stop motors: perform combination stick command.
2. Takeoff: slowly push the left control stick (Mode 2) up to take off.
3. Landing: slowly push the left control stick (Mode 2) down until the aircraft lands.
Hold for three seconds to stop the motors.
Specifications
Aircraft (Model: T740)
Operating Temperature
-20°C to 40°C
O3 Pro
Operating Frequency
2.400-2.4835 GHz, 5.150-5.250GHz，
5.725-5.850 GHz
Battery (Model: BWX630-4280-23.1)
Capacity
4280 mAh
Standard Voltage
23.1 V
Charging Temperature
5°C to 40°C
Max Power Rate
203 W
Battery Safety Notice
• DO NOT allow liquid to come into contact with the batteries. DO NOT leave
batteries covered in moisture or out in the rain. DO NOT drop the batteries into
water. Otherwise, an explosion or fire may occur.
• DO NOT use non-DJI batteries. It is recommended to use DJI chargers.
• DO NOT use swollen, leaking, or damaged batteries. In such situations, contact DJI
or a DJI authorized dealer.
• The batteries should be used at a temperature between -10° and 40° C (14° and
104° F). A high temperature can cause an explosion or fire. A low temperature will
reduce the performance of a battery.
• DO NOT disassemble or pierce the battery in any way.
• The electrolytes in the battery are highly corrosive. If any electrolytes come into
contact with your skin or eyes, immediately wash the affected area with water and
seek medical support.
• Keep batteries out of the reach of children and animals.
• DO NOT use a battery if it is involved in a crash or heavy impact.
• Extinguish any battery fire using water, sand, or a dry powder fire extinguisher.
• DO NOT charge the battery immediately after flight. The battery temperature may
be too high and may cause serious damage to the battery. Allow the battery to cool
down to close to room temperature before charging. Charge the battery at a
temperature range of 5° to 40° C (41° to 104° F). The ideal charging temperature
range is 22° to 28° C (72° to 82° F). Charging at the ideal temperature range can
prolong battery life.
• DO NOT leave the battery near heat sources such as a furnace or heater. DO NOT
leave the battery inside a vehicle on hot days.
• DO NOT store the battery for an extended period after fully discharging.
Otherwise, the battery may over-discharge and cause irreparable damage to the
battery cell.
• If a battery with a low power level has been stored for an extended period, the
battery will enter deep hibernation mode. Recharge the battery to bring it out of
hibernation.
FCC Compliance Notice
Supplier’s Declaration of Conformity
Product name: INSPIRE 3
Model Number: T740
Responsible Party: DJI Technology, Inc.
Responsible Party Address: 201 S. Victory Blvd., Burbank, CA 91502
Website: www.dji.com
We, DJI Technology, Inc., being the responsible party, declares that the above mentioned model
was tested to demonstrate complying with all applicable FCC rules and regulations.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
The aircraft complies with FCC radiation exposure limits set forth for an uncontrolled
environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure
limits, human proximity to the antenna shall not be less than 20cm during normal operation.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
ISED Compliance Notice
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions: (1)This device may not cause interference.(2)This device must accept
any interference, including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux
CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :(1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Cet équipement est conforme aux limites d'exposition aux radiations CNR-102 établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance
minimale de 20 cm entre le radiateur et votre corps.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
dans d''autres langues
- English: dji T740 User guide
Documents connexes
-
dji Mavic 3 Cine Mode d'emploi
-
dji RC Pro Mode d'emploi
-
dji FPV Drone Combo Mode d'emploi
-
dji FD1W4K Mode d'emploi
-
-
-
dji Pilot Guide de démarrage rapide
-
dji MT2SD Mini 2 SE Fly Combo Camera Drone Mode d'emploi
-
dji B08YR48SZ1 Air 2S Drone Quadcopter Mode d'emploi
-
dji Mavic 2 Mode d'emploi
