INSTALLATION INSTRUCTIONS
CPU Interface Adapter
PAC-252
PAC-252 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies, Inc., and its affiliated corporations
and subsidiaries (collectively, "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
WARNING: Failure to provide adequate structural strength
for this component can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the structure to which this component is attached
can support five times the combined weight of all equipment.
Reinforce the structure as required before installing the
component.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
all components does not exceed the maximum weight
capacity of the mount to which this accessory is being
installed.
Installation Instructions PAC-252
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PAC-252 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
1/8" (included)
5/32" (included)
A (1)
B (2)
C (6)
D (4)
E (4)
F (8)
10-24x3/8"
G (4)
10-24x7/8"
H (4)
10-24x3/8"
I (8)
10-24x3/8"
J (1)
1/8" K (1)
5/32"
Phillips
Installation Instructions PAC-252
5
Assembly And Installation
1. Using a 10-24 button head cap screw (G) inserted from
inside of bracket, secure mounting button (E), with
chamfered hole of mounting button (larger surface) facing
bracket, to bracket. Repeat with other three mounting
buttons. (See Figures 1 & 2)
Figure 1
Figure 2
2. Attach large bumpers (D), making sure the CPU will rest
against the bumpers when installed. (See Figures 3 & 4)
Figure 3
Figure 4
PAC-252 Installation Instructions
6
3. Attach small bumpers (C), making sure the CPU will rest
against the bumpers when installed. (See Figures 5 & 6)
Figure 5
Figure 6
4. Turn adapter on its end. (See Figure 7)
5. If necessary, slide brackets out of the way before installing
the CPU inside adapter.
6. Install the CPU Inside adapter.
7. Adjust side brackets until they firmly press against sides
and top of CPU.
8. while pressing brackets against CPU, tighten all Nylock
nuts. The CPU should now be completely rigid inside of
adapter.
Figure 7
9. Using 10-24 pan head Phillips or button head security
screws (I or H), secure side covers. (See Figure 8)
Figure 8
10. Lift Interface Adapter (A) up to Chief Mount, aligning buttons
(E) of adapter with slots in the Chief Mount. Make sure the
tear drop slots of Interface Adapter (A) face down
replicating those of the Chief Mount.
11. Raise safety latch on Chief Mount to secure Display, making
sure latch is completely engaged.
12. With the aid of another person, lift Large Flat Panel Display
up to the PAC-252 CPU Interface Adapter (A), aligning
buttons of mounting brackets with slots in adapter.
13. Raise safety latch on PAC-252 to secure Display, making
sure latch is completely engaged.
Safety latch
Installation Instructions PAC-252
7
PAC-252 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8832-000081 Rev 01
2010 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
08/10
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
dans d''autres langues
- English: Chief PAC252 Installation guide
Documents connexes
-
Chief PAC400 Guide d'installation
-
-
-
-
Chief FCA651B Guide d'installation
-
Chief FCA515 Guide d'installation
-
Chief Manufacturing TA410 Manuel utilisateur
-
-
Chief PACCS1 Guide d'installation
-