Dell PowerEdge C5220 Guide de démarrage rapide

Dell PowerEdge C5220

Getting Started

With Your System

Guide de mise en route

Primeiros passos com o sistema

Procedimientos iniciales con el sistema

Dell PowerEdge C5220

Getting Started

With Your System

Regulatory Model B04S

Notes, Cautions, and Warnings

____________________

Information in this publication is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc.

is strictly forbidden.

Trademarks used in this text: Dell™, the DELL logo, and PowerEdge™ are trademarks of Dell Inc.

Intel

®

and Intel

®

Xeon

®

are registered trademarks of Intel Corporation in the U.S. and other countries.

Microsoft

®

and Windows

®

are either trademarks or registered trademarks of Microsoft Corporation

in the United States and/or other countries. Red Hat

®

and Red Hat Enterprise Linux

®

are registered

trademarks of Red Hat, Inc. in the United States and/or other countries. SUSE™ is a trademark of

Novell Inc. in the United States and other countries. Citrix

®

, Xen

®

, and XenServer

®

are either

registered trademarks or trademarks of Citrix Systems, Inc. in the United States and/or other countries.

VMware

®

is a registered trademarks or trademarks of VMWare, Inc. in the United States or other

countries.

Other trademarks and trade names may be used in this publication to refer to either the entities claiming

the marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and

trade names other than its own.

Regulatory Model B04S

2011-04 P/N F8DV3 Rev. A00

NOTE: A NOTE indicates important information that helps you make better use

of your system.

CAUTION: A CAUTION indicates potential damage to hardware or loss of data

if instructions are not followed.

WARNING: A WARNING indicates a potential for property damage, personal

injury, or death.

Installation and Configuration 3

This server is intended for installation only in restricted access locations as

defined in Cl. 1.2.7.3 of IEC 60950-1: 2001 where both these conditions

apply:

• Access can only be gained by service persons or by users who have been

instructed about the reasons for the restrictions applied to the location and

about any precautions that shall be taken.

• Access is through the use of a tool or lock and key, or other means of

security, and is controlled by the authority responsible for the location.

Installation and Configuration

Unpacking the System

Unpack your system and identify each item.

Installing the Tool-Less Rail Solution

CAUTION: Restricted Access Location

WARNING: Before performing the following procedure, review and follow the

safety instructions that came with the system.

WARNING: Whenever you need to lift the system, get others to assist you. To

avoid injury, do not attempt to lift the system by yourself.

WARNING: The system is not fixed to the rack or mounted on the rails. To avoid

personal injury or damage to the system, you must adequately support the system

during installation and removal.

WARNING: To avoid a potential electrical shock hazard, a third wire safety

grounding conductor is necessary for the rack installation. The rack equipment

must provide sufficient airflow to the system to maintain proper cooling.

CAUTION: When installing rails in a square-hole rack it is important to ensure

that the square peg slides through the square holes.

CAUTION: Square studs must be flush with the rack posts to install properly.

4 Installation and Configuration

1

Pull on the latch release buttons on the end piece midpoints to open the

rail latches.

2

Align the end pieces of the rails on the vertical rack flanges to seat the pegs

in the bottom hole of the first U and the top hole of the second U. Engage

the back end of the rail until the latch locks in place.

3

Repeat steps 1 to 2 to position and seat the front end piece on the vertical

flange.

NOTE: The rails can be used in both square-hole and round-hole racks.

NOTE: To remove the rails, pull on the latch release button on the end piece

midpoint and unseat each rail.

Front

Back

Installation and Configuration 5

Installing the System

Empty the System Chassis

1

Unplug the power cable from the power supply unit.

.

2

Pull out the power supply unit handle.

6 Installation and Configuration

3

Press down on the release latch



.

4

Pull the power supply unit out of the system



.

5

Press the release latch down



.

6

Pull the sled out of the system



.

Installation and Configuration 7

Installing the System Into the Rack

1

Slide the system into the rack.

2

If present, remove the chassis stabilizer shipping bracket (optional) from

the rack.

3

Tighten the captive thumbscrews to secure the ears of the system to the

front of the rack.

WARNING: Whenever you need to lift the system, get others to assist you.

To avoid injury, do not attempt to lift the system by yourself.

NOTE: To transport systems already installed in the rack, ensure that the two

chassis stabilizer shipping brackets (optional) are in place.

NOTE: Make sure the latch release mechanism is engaged correctly.

8 Installation and Configuration

Populate the System

1

Push the power supply unit into the system until flush with the case and

the release latch locks.

2

Close the power supply unit handle.

Installation and Configuration 9

3

Plug the chassis power cable into the power supply unit.

NOTE: The correct configuration of the integral chassis AC power cables to the

PSU sockets is as shown in the following illustration.

1 2 3 4 5 6 7 8 9 10 11 12

PSU1 PSU2

10 Installation and Configuration

4

Push the sled into the system until flush with the case and the release latch

locks.

Connecting the Keyboard, Mouse, and Monitor

The connector on the front of your system has an icon indicating which cable

to plug in. Connect a keyboard, mouse, or monitor (optional).

Installation and Configuration 11

Connecting the Power Cables

1

On the back of the system, connect the mains power cable to the system’s

power socket.

2

Plug the other end of the power cables into a grounded electrical outlet or

a separate power source such as an uninterrupted power supply or a power

distribution unit.

Turning On the System

When connected to a power source the system automatically powers on.

See Using the Baseboard Management Controller Guide at

support.dell.com/manuals.

NOTE:

AC Port 1 provides power to PSU1, AC Port 2 provides power to PSU2.

For more information, see step 3 of Populate the System.

AC Port 2

AC Port 1

12 Installation and Configuration

Complete the Operating System Setup

To install an operating system for the first time, see the installation and

configuration documentation for your operating system. Be sure the

operating system is installed before installing hardware or software not

purchased with the system.

Supported Operating Systems

• Microsoft Windows Server 2008 R2 Enterprise

• Microsoft HPC Server 2008 R2

• Microsoft Windows Server 2008 R2 Hyper-V

• Red Hat Enterprise Linux 6.0 (64-bit)

• Red Hat Enterprise 5 Update 5 (64-bit)

• SUSE Linux Enterprise Server 11 Service Pack 1 (64-bit)

• VMware ESX 4.1 Update 1

• VMware ESXi 4.1 Update 1 (Embedded option for SDHC)

• Citrix XenServer 5.6 Feature Pack 1

Other Information You May Need

See the Hardware Owner’s Manual at support.dell.com/manuals for

information about system features, troubleshooting, and component

replacement.

See Using the Baseboard Management Controller Guide at

support.dell.com/manuals.

NOTE:

For the latest information on supported operating systems, see

support.dell.com.

WARNING: See the safety and regulatory information that shipped with your

system. Warranty information may be included within this document or as a

separate document.

NOTE: Always check for updates on support.dell.com/manuals and read the

updates first because they often supersede information in other documents.

Technical Specifications 13

Technical Specifications

Processor (Per System Board)

Processor type Intel Xeon Processor E3-1200 product

family

Expansion Bus (Per System Board)

Bus type PCI-E x8 Gen 2

Expansion slots Mezzanine connector

Memory (Per System Board)

Architecture Dual Channel Unbuffered DDR3

1066/1333

Memory module sockets 4

Memory module capacities

Minimum RAM 2 GB

Maximum RAM 32 GB

Drives (Per System Board)

2.5" hard drives SAS 6 Gb (4 channels)

SATA 3 Gb (4 channels)

3.5" hard drives SAS 6 Gb (2 channels)

SATA 3 Gb (2 channels)

Connectors (Per System Board)

Front

NIC 10/100/1G (RJ45)

2

USB 2.0 (through Y-cable)

2

Video (DB15) (through Y-cable)

1

Video

Video type AST2050

Video memory 8 MB DDR2 SDRAM

14 Technical Specifications

Power

AC power supply (per power supply)

Wa tt ag e

1400 W

Voltage

200-240 VAC, 50/60 Hz

Heat dissipation

55.67 BTU/hr max

Maximum inrush current

55 A max

Physical

Height 13 cm (5.1 in)

Width 44.7 cm (17.6 in)

Depth 75 cm (29.5 in)

Weight (loaded: maximum weight) 8-sled configuration:

42.4 kg (93.48 lbs.)

12-sled configuration:

48.13 kg (106.11 lbs.)

Weight (empty) 8-sled configuration:

27.4 kg (60.41 lbs.)

12-sled configuration:

32.02 kg (70.59 lbs.)

Environmental

NOTE: For additional information about environmental measurements for specific

system configurations, see dell.com/environmental_datasheets.

Temperature

Operating

10°C to 35°C (50°F to 95°F) with a

maximum temperature gradation of 10°C

(per hour)

NOTE: For altitudes above 2,950 feet, the

maximum operating temperatures derated

to 1°F/550 ft.

Storage

–40°C to 65°C (-40°F to 149°F) with a

maximum temperature gradation of 20°C

per hour

Technical Specifications 15

Relative Humidity

Operating

20% to 80% (noncondensing) with a

maximum humidity gradation of 10%

per hour

Storage

5% to 95% (noncondensing)

Maximum vibration

Operating

0.26 Grms at 5–350 Hz

Storage

1.87 Grms at 10–500 Hz for 15 minutes

Maximum shock

Operating

One shock pulse in the positive z axis

(one pulse on each side of the system) of

31 G for 2.6 ms in the operational

orientation

Storage

Six consecutively executed shock pulses

in the positive and negative x, y, and z

axes (one pulse on each side of the

system) of 71 G for up to 2 ms.

Six consecutively executed shock pulses

in the positive and negative x, y, and z

axes (one pulse on each side of the

system) of 22 G faired square wave pulse

with velocity change at 200 inches/second

Altitude

Operating

-16 to 3,048 m (-50 to 10,000 ft.)

Storage

-16 to 10,600 m (-50 to 35,000 ft.)

Airborne Contaminant Level

Class

G1 as defined by ISA-S71.04-1985

Environmental (continued)

16 Technical Specifications

Acoustics

Sound Power (Units: LwAd-UL,bels)

Idle in 23 ± 2

°

C ambient

<= 7.0

SPEC power at 50% in 23 ± 2

°

C

ambient

<= 7.2

NOTE: LwAd-UL is the upper limit sound power level (LwAd) calculated by ISO 9296

(1988) and measured in accordance with ISO7779 (1999).

Dell PowerEdge C5220

Guide de

mise en route

Modèle réglementaire B04S

Remarques, précautions et avertissements

____________________

Les informations contenues dans ce document sont sujettes à modification sans préavis.

La reproduction de ce document, de quelque manière que ce soit, sans l'autorisation écrite de Dell Inc.

est strictement interdite.

Marques utilisées dans ce document : Dell™, le logo DELL et PowerEdge™ sont des marques de

Dell Inc. Intel

®

et Intel

®

Xeon

®

sont des marques déposées d'Intel Corporation aux États-Unis et dans

d'autres pays. Microsoft

®

et Windows

®

sont des marques ou des marques déposées de Microsoft

Corporation aux États-Unis et/ou dans d'autres pays. Red Hat

®

et Red Hat Enterprise Linux

®

sont des

marques déposées de Red Hat, Inc. aux États-Unis et/ou dans d'autres pays. SUSE™ est une marque

de Novell Inc. aux États-Unis et dans d'autres pays. Citrix

®

, Xen

®

et XenServer

®

sont des marques

déposées ou des marques de Citrix Systems, Inc. aux États-Unis et/ou dans d'autres pays. VMware

®

est une marque déposée ou une marque de VMware, Inc. aux États-Unis ou dans d'autres pays.

D'autres marques et noms commerciaux peuvent être utilisés dans ce document pour faire référence

aux entités revendiquant la propriété de ces marques ou de ces noms de produits. Dell Inc. rejette tout

intérêt propriétaire dans les marques et les noms commerciaux autres que les siens.

Modèle réglementaire B04S

04-2011 N/P F8DV3 Rév. A00

REMARQUE : une REMARQUE indique des informations importantes qui peuvent

vous aider à mieux utiliser votre système.

PRÉCAUTION : une PRÉCAUTION indique un risque d'endommagement du

matériel ou de perte de données en cas de non respect des instructions.

AVERTISSEMENT : un AVERTISSEMENT indique un risque d'endommagement

du matériel, de blessures corporelles ou même de mort.

La page est en cours de chargement...

Dell PowerEdge C5220 Guide de démarrage rapide

Dell PowerEdge C5220 Guide de démarrage rapide

dans d''autres langues

Documents connexes