Marcy NS-40501E Le manuel du propriétaire

NOTE:

Please read all instructions

carefully before using this

product

Veuillez lire attentivement les

instructions du présent manuel

avant d’utiliser ce produit.

Table of Contents / Table des

matières

Safety Notice / Avis sur la

sécurité

Important Assembly Information

/ Renseignements importants

liés à l’assemblage

Care and Maintenance /

Entretien

Parts List / Liste des pièces

Warranty / Garantie

Ordering Parts / Commander

des pièces

Model / Modèle

NS-40501E

Retain This Manual for

Reference /

Conserverce manuel

comme référence

230419

OWNER'S

MANUAL /

MANUEL DU

PROPRIÉTAIRE

Magnetic-Resistance

Elliptical Exerciser / Exerciceur

elliptique à résistance magnétique

NS-40501E

IMPEX® INC.

2801 S. Towne Ave, Pomona, CA 91766

Tel: (800) 999-8899 Fax: (626) 961-9966

www.marcypro.com

support@impex-fitness.com

1

TABLE OF CONTENTS

BEFORE YOU BEGIN

Thank you for selecting the MARCY Magnetic-Resistance Elliptical Exerciser

NS-40501E by IMPEX® INC. For your safety and benefit, read this manual

carefully before using the bike. As a manufacturer, we are committed to provide

you complete customer satisfaction. If you have any questions, or find there are

missing or damaged parts, we guarantee you complete satisfaction through

direct assistance from our factory. To avoid unnecessary delays, please call our

TOLL-FREE customer service number. Our Customer Service Agents will

provide immediate assistance to you.

BEFORE YOU BEGIN

1

IMPORANT SAFETY NOTICES

2

WARNING LABEL PLACEMENT

3

HARDWARE PACK

4

ASSEMBLY INSTRUCTION

7

EXPLODED DIAGRAM

15

PARTS LIST

17

CARE AND MAINTANENCE AND STORAGE

19

OPERATING NOTES

19

COMPUTER

20

WARRANTY

21

ORDERING PARTS

21

Toll-Free Customer Service Number

1-800-999-8899

Mon. - Fri. 9 a.m. - 5 p.m. PST

www.impex-fitness.com

support@impex-fitness.com

2

IMPORTANT SAFETY NOTICE

PRECAUTIONS

This exercise machine is built for optimum safety. However, certain precautions apply

whenever you operate a piece of exercise equipment. Be sure to read the entire manual

before you assemble or operate your machine. In particular, note the following safety

precautions:

1. Keep children and pets away from the machine at all times. DO NOT leave

children unattended in the same room with the machine.

2. Only one person at a time should use the machine.

3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,

STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.

4. Position the machine on a clear, leveled surface. DO NOT use the machine near water

or outdoors.

5. Keep hands away from all moving parts.

6. Always wear appropriate workout clothing when exercising. DO NOT wear robes or

other clothing that could become caught in the machine. Running or aerobic shoes are

also required when using the machine.

7. Use the machine only for its intended use as described in this manual. DO NOT use

attachments not recommended by the manufacturer.

8. Do not place any sharp object around the machine.

9. Disabled person should not use the machine without a qualified person or physician in

attendance.

10. Before using the machine to exercise, always do stretching exercises to properly warm

up.

11. Never operate the machine if the machine is not functioning properly.

12. Read all warnings posted on the exercise bike.

13. Inspect the exercise bike for worn or loose component prior to use. Tighten/replace any

loose or wore components prior to use.

14. Care should be taken in mounting or dismounting the exercise bike.

15. This exercise bike is for consumer and home use only.

WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR

PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE

OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ ALL

INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. IMPEX INC. ASSUMES

NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE

SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT.

SAVE THESE INSTRUCTIONS.

3

WARNING LABEL PLACEMENT

The Warning Labels shown here has been placed on the Rear Stabilizer.

If the labels are missing or illegible, please call customer service at 1-800-999-8899 for replacement. Apply the

labels in location shown.

4

HARDWARE PACK

NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size.

NO. DESCRIPTION Q’TY Drawings

6 Carriage M10 x 3” 4

7 Curved washer Ø ⅞” 4

8 Acorn Nut M10 4

16 Aircraft Nut M10 2

17 Flat Washer Ø ¾” 2

18 Sleeve 2

20 Hex Bolt M10 x 3 ⅛” 2

14 Hex Bolt M8 x 1 ¾” 4

23 Allen Bolt M8 x ⅝” 6

10L/R Pedal Axle Bolt 1/1

11 Wrinkled Washer 2

35 Allen Bolt M6 x ½” 4

36 Carriage Bolt M6 x ¾” 4

15 Lock knob 4

5

29 Hex Bolt M10 x ¾” 2

30 Lock Washer Ø ⅜” 2

31 Ø 1 ¼” x Ø ⅜” 2

32 D Washer 2

12 Flat Washer Ø 1 ⅛” 2

51L/R Hex Nut 1/1

41 Curve Washer Ø ¾” x Ø ⅜” 6

Allen key L6 1

Allen key L4 1

Allen key L8 1

Allen wrench 2

6

COMPONENTS FOR ASSEMBLY

7

ASSEMBLY INSTRUCTION

• Tools Required For Assembling the Machine: One Crossing Wrench and Allen Wrench,

provided by manufacturer.

• NOTE: It is strongly recommended that two or more people assemble this machine to

avoid possible injury.

STEP-1

A.) Attach the Rear Stabilizer (#2) to the Main Frame (#1). Secure it with two M8 x 3” Carriage Bolts

(#6), two Ø ⅞” Curved Washers (#7), and two Acorn Nuts (#8).

B.) Attach the Front Stabilizer (#3) to the Main Frame. Secure it with two M8 x 3” Carriage Bolts (#6),

two Ø ⅞” Curved Washers (#7), and two Acorn Nuts (#8).

8

STEP-2

A.) Remove the Tension Knob Screw (#50) and Ø ½” Washer (#49) from the Tension Knob.

B.) Insert the Upper Tension Cable (#25) through the opening on Front Post to the bottom of the

Front Post.

C.) Plug the Tension Knob (#25) into the opening, secure the Tension Knob to Front Post with

the Tension Knob Screw (#50) and the Ø ½” Washer (#49).

9

STEP-3

A.) NOTE: Extra help may be needed to hold the Front Post (#22) while connecting the

cables and wires.

B.) Attach the Front Post (#22) to the Main Frame (#1). Connect the Upper Computer Wire (#26)

from the bottom of the Front Post to the Lower Computer Wire (#28) from the Main Frame.

C.) Pull the tension connector from the Upper Tension Cable (#25) and slide in between the

opening on the connector on the Lower Tension Cable (#27). Pull the Upper Tension Cable

upward and slide the wire through the slot on the bracket.

D.) Drop down the Upper Tension Cable so the fitting sits firmly on top of the bracket.

E.) Secure the Front Post to the Main Frame with four M8 x 5/8” Allen Bolts (#23), and four Ø ¾” x

Ø ⅜” Curved Washers (#41).

10

STEP-4

A.) Attach left Stride Tube (#21L) to the left axle on Front Post (#22).

B.) Secure the Stride Tube (#21L) to Front Post with one D Washer (#32), one Ø 1 ¼” x Ø ⅜” Flat

Washer (#31), one Ø ⅜” Lock Washer (#30), and one M10 x ¾” Hex Bolt (#29).

C.) Cover the pivot joint with two left Stride Tube Covers (#47L) and secure them together with two

ST5 x ⅝” Self Tapping Screws (#33).

D.) Cover the bottom of Left Stride Tube with one Stride Tube Bottom Cover Set (#52) and secure

with two ST4 x 1 ⅛” Self Tapping Screws (#53)

E.) Repeat A, B, C, and D to install Right Stride Tube (#21R) to Front Post.

STEP-5

11

A.) Do not tighten Nuts and Bolts until instructed to do so.

B.) Place the pivot on bottom of left Stride Tube (#21L) to the open bracket on Left Pedal

Support (#9L). Secure the Tube to the Left Pedal Support with one M10 x 3 ⅛” Hex Bolt

(#20), one Sleeve (#18), one Ø ¾” Washer (#17), and one M10 Aircraft Nut (#16).

C.) Attach the Left Pedal Support rear pivot to the Crank (#24). Secure it with one Left Pedal

Axle Bolt (#10L), one Wrinkled Washer (#11), one Ø 1 ⅛” Flat Washer (#12), and one left

Hex Nut (#51L).

D.) Securely tighten all Nuts and Bolts.

E.) Cover the bottom of left Stride Tube and front Left Pedal Support with two left Pedal Support

Covers (#54L), secure them with two M5 x ⅜” Self Tapping Screws (#55).

F.) Place the Left Pedal (#13L) onto Left Pedal Support, secure with two M8 x 1 ¾” Hex Bolts

(#14) and two Lock Knobs (#15).

STEP-6

12

A.) Do not tighten Nuts and Bolts and Nuts until instructed to so.

B.) Place the pivot on bottom of right Stride Tube (#21R) to the open bracket on Right Pedal

Support (#9R). Secure the Tube to the right Pedal Support with one M10 x 3 ⅛” Hex Bolt

(#20), one Sleeve (#18), one Ø ¾” Washer (#17), and one M10 Aircraft Nut (#16).

C.) Attach the Right Pedal Support rear pivot to the Crank (#24). Secure it with one Right Pedal

Axle Bolt (#10R), one Wrinkled Washer (#11), one Ø 1 ⅛” Flat Washer (#12), and one right

Hex Nut (#51R).

D.) Securely tighten all Nuts and Bolts.

E.) Cover the bottom of right Stride Tube and front Right Pedal Support with two right Pedal

Support Covers (#54R), secure them with two M5 x ⅜” Self Tapping Screws (#55).

F.) Pace the Right Pedal (#13R) onto the Right Pedal Support, secure with two M8 x 1 ¾” Hex

Bolts (#14) and two Lock Knobs (#15).

STEP-7

13

A.) Attach the Stationary Handle (#39) to Front Post (#22). Secure it with two M8 x ⅝” Allen

Bolts (#23) and two Ø ¾” x Ø ⅜” Curve Washers (#41).

B.) Remove four M5 x ½”Philips Screws (#48) from Computer (#38). Connect the computer wire

from Computer to the Upper Computer Wire (#26) from Front Post. Slide the computer onto

the bracket on Front Post. Secure the Computer to the bracket with the four M5 x ½”Philips

Screws (#48).

STEP-8

14

A.) Place the left Stride Handle (#37L) onto left Stride Tube (#21L). Secure it with two M6 x ¾”

Carriage Bolts (#36) and two M6 x ½” Allen Bolts (#35).

B.) Repeat A to install right Stride Handle (#37R) to right Stride Tube (#12R).

EXPLODED DIAGRAM

15

EXPLODED DIAGRAM

16

NS-40501E PARTS LIST

17

PART

NO.

DESCRIPTION

SPEC.

QUANTITY

1

Main Frame

1

2

Rear Stabilizer

1

3

Front Stabilizer

1

4

Rear Stabilizer End Cap

2

5

Front Stabilizer End Cap

2

6

Carriage Bolt

M10 x 3”

4

7

Curve Washer

Ø ⅞”

4

8

Acorn Nut

M10

4

9L

Left Pedal Support

1

9R

Right Pedal Support

1

10L

Left Pedal Axle Bolt

1

10R

Right Pedal Axle Bolt

1

11

Wrinkled Washer

2

12

Flat Washer

Ø 1 ⅛”

2

13L

Left Pedal

1

13R

Right Pedal

1

14

Hex Bolt

M8 x 1 ¾”

4

15

Lock Knob

4

16

Aircraft Nut

M10

2

17

Washer

Ø ¾”

2

18

Sleeve

2

19

Upper Stride Handle End Cap

2

20

Hex Bolt

M10 x 3 ⅛”

2

21L/R

Stride Tube

1/1

22

Front Post

1

23

Allen Bolt

M8 x ⅝”

6

24

Crank

1

25

Tension Knob/Upper Tension Cable

1

26

Upper Computer Wire

1

27

Lower Tension Cable

1

28

Lower Computer Wire

1

29

Hex Bolt

M10 x ¾”

2

30

Lock Washer

Ø ⅜”

2

31

Flat Washer

Ø 1 ¼” x Ø ⅜”

2

32

D Washer

2

33

Self Tapping Screw

ST5 x ⅝”

4

34

Plastic Spacer

2

35

Allen Bolt

M6 x ½”

4

36

Carriage Bolt

M6 x ¾”

4

37L/R

Stride Handle

1/1

38

Computer

1

18

39

Stationary Handle

1

40

Stationary Handle End Cap

Ø 1”

2

41

Curve Washer

Ø ¾” Ø ⅜”

6

42

Counter Sunk Self Tapping Screw

ST5 x ⅝”

2

43

Flat Self Tapping Screw

ST5 x ⅝”

2

44

Stationary Handle Grip

2

45

Stride Handle Grip

2

46L/R

Front Post Cover

1/1

47L/R

Stride Tube Cover

2/2

48

Philips Screw

M5 x ½”

4

49

Washer

Ø ½”

1

50

Tension Knob Screw

M5 x 1 ⅝”

1

51L/R

Hex Nut

1/1

52

Stride Tube Bottom Cover Set

2

53

Self Tapping Screw

ST4 x 1 ⅛”

4

54L/R

Pedal Support Cover

2/2

55

Philips Screw

M5 x ⅜”

4

56

Self Tapping Screw

ST4 x ⅝”

2

57

Hardware Pack

1

58

Button Head Self Tapping Screw

ST5 x ⅝”

8

59

Flat Head Self Tapping Screw

ST5 x ⅝”

4

60

Nylon Nut

M6

2

61

Flywheel Axle Lock Washer

2

62

Flywheel Axle

1

63

Hex Bolt

M8 x 4 ⅛:

1

64

Magnet Assembly Bushing

2

65

Magnet Assembly

1

66

Ball Bearing Set

1

67

Belt

1

68

Computer Wire Sensing Base

1

69

Magnet Assembly Spring

1

70

Hex Bolt

M6 x 1”

1

71

Hex Nut

M6

2

72

Nylon Nut

M8

1

73

Main Frame Cover L/R

1/1

74

Crank End Cover

2

75

Flywheel

1

76

Flange Nut

2

77

Ring Bolt

2

78

Locking Clamp

2

CARE, MAINTENANCE AND STORAGE

19

1. Inspect and tighten all parts each time you use the machine. Replace any worn parts

immediately.

2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent. Do not use

solvents.

3. Store the bike IN-DOOR. Excess moisture and water would cause rust on the frame.

4. The Bike shall be placed at least 24 inches away from the wall or/and any other object such as

furniture to provide safe access to and passage around the machine.

5. To avoid possible injury, the help of two or more people are needed when moving the machine

around.

6. Disposal Instructions – The equipment can be safely disassembled and disposed without

unreasonable hazards. Call your local recycle agency regarding details of recycling.

7. The maximum user weight is 300 lbs.

8. Assembled Dimension: 49” x 24” x 64.25”

OPERATING NOTES

Tension Adjustment

Use the Tension Knob on Front Post to adjust the exercising resistance.

FOOT POSITIONING

Step with both feet on the two Pedals and hold the Stride Handles with two hands, and then

start to exercise. NOTE: DO not stand on one Pedal with both feet, or just step one foot

on one Pedal during exercise.

TRANSPORT

The Bike has a pair of roller wheels on Front Stabilizer End Cap.

To move, carefully hold and tilt the machine, and roll.

COMPUTER

La page charge ...

Marcy NS-40501E Le manuel du propriétaire

Marcy NS-40501E Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents