Zanussi ZDI26022XA Manuel utilisateur

Marque: Zanussi

Modèle: ZDI26022XA

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

GETTING

STARTED?

EASY.

User Manual

ZDI26022XA

EN User Manual 2

Dishwasher

FR Notice d'utilisation 20

Lave-vaisselle

VISIT OUR WEBSITE TO:

Get usage advice, brochures, trouble shooter, service and repair information:

www.zanussi.com/support

SAFETY INFORMATION

Before the installation and use of the appliance, carefully read the

supplied instructions. The manufacturer is not responsible for any

injuries or damage that are the result of incorrect installation or

usage. Always keep the instructions in a safe and accessible

location for future reference.

CHILDREN AND VULNERABLE PEOPLE SAFETY

• This appliance can be used by children aged from 8 years and

above and persons with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have

been given supervision or instruction concerning the use of the

appliance in a safe way and understand the hazards involved.

• Children between 3 and 8 years of age and persons with very

extensive and complex disabilities shall be kept away from the

appliance unless continuously supervised.

• Children of less than 3 years of age should be kept away from

the appliance unless continuously supervised.

• Do not let children play with the appliance.

• Keep detergents away from children.

• Keep children and pets away from the appliance when the door

is open.

• Children shall not carry out cleaning and user maintenance of

the appliance without supervision.

GENERAL SAFETY

• This appliance is intended to be used in household and similar

applications such as:

– farm houses; staff kitchen areas in shops, ofﬁces and other

working environments;

– by clients in hotels, motels, bed & breakfast and other

residential type environments.

• Do not change the speciﬁcation of this appliance.

• The operating water pressure (minimum and maximum) must be

between 0.5 (0.05) / 8 (0.8) bar (MPa)

• Follow the maximum number of 13 place settings.

• If the supply cord is damaged, it must be replaced by the

manufacturer, its Authorised Service Centre or similarly

qualiﬁed persons in order to avoid a hazard.

• Put the cutlery in the cutlery basket with the sharp ends

pointing down or put them in the cutlery drawer in a horizontal

position with the sharp edges down.

• Do not leave the appliance with the open door unattended to

avoid stepping accidentally onto it.

• Before any maintenance operation, deactivate the appliance

and disconnect the mains plug from the socket.

• Do not use high pressure water sprays and/or steam to clean

the appliance.

• If the appliance has ventilation openings in the base, they must

not be covered e.g. by a carpet.

• The appliance is to be connected to the water mains using the

new supplied hose-sets. Old hose sets must not be reused.

SAFETY INSTRUCTIONS

INSTALLATION

WARNING! Only a qualiﬁed person

must install this appliance.

• Remove all the packaging.

• Do not install or use a damaged appliance.

• Do not use the appliance before installing it in

the built-in structure due to safety manner.

• Follow the installation instructions supplied with

the appliance.

• Always take care when moving the appliance as

it is heavy. Always use safety gloves and

enclosed footwear.

• Do not install or use the appliance where the

temperature is less than 0 °C.

• Install the appliance in a safe and suitable place

that meets installation requirements.

ELECTRICAL CONNECTION

WARNING! Risk of ﬁre and electric

shock.

• The appliance must be earthed.

• Make sure that the parameters on the rating

plate are compatible with the electrical ratings

of the mains power supply.

• Always use a correctly installed shockproof

socket.

• Do not use multi-plug adapters and extension

cables.

• Make sure not to cause damage to the mains

plug and to the mains cable. Should the mains

cable need to be replaced, this must be carried

out by our Authorised Service Centre.

• Connect the mains plug to the mains socket

only at the end of the installation. Make sure that

there is access to the mains plug after the

installation.

• Do not pull the mains cable to disconnect the

appliance. Always pull the mains plug.

• This appliance is ﬁtted with a 13 A mains plug. If

it is necessary to change the mains plug fuse,

use only a 13 A ASTA (BS 1362) fuse (UK and

Ireland only).

WATER CONNECTION

• Do not cause damage to the water hoses.

• Before connection to new pipes, pipes not used

for a long time, where repair work has been

carried out or new devices ﬁtted (water meters,

etc.), let the water ﬂow until it is clean and clear.

• Ensure that there are no visible water leaks

during and after the ﬁrst use of the appliance.

• The water inlet hose has a safety valve and a

sheath with an inner mains cable.

WARNING! Dangerous voltage.

• If the water inlet hose is damaged, immediately

close the water tap and disconnect the mains

plug from the mains socket. Contact the

Authorised Service Centre to replace the water

inlet hose.

USE

• Do not put ﬂammable products or items that are

wet with ﬂammable products in, near or on the

appliance.

• Dishwasher detergents are dangerous. Follow

the safety instructions on the detergent

packaging.

• Do not drink and play with the water in the

appliance.

• Do not remove the dishes from the appliance

until the programme is complete. Some

detergent may remain on the dishes.

• Do not store items or apply pressure on the

open door of the appliance.

• The appliance can release hot steam if you open

the door while a programme operates.

INTERNAL LIGHTING

WARNING! Risk of injury.

• Concerning the lamp(s) inside this product and

spare part lamps sold separately: These lamps

are intended to withstand extreme physical

conditions in household appliances, such as

temperature, vibration, humidity, or are intended

to signal information about the operational

status of the appliance. They are not intended to

be used in other applications and are not

suitable for household room illumination.

• To replace the internal lighting, contact the

Authorised Service Centre.

SERVICE

• To repair the appliance contact the Authorised

Service Centre. Use original spare parts only.

• Please note that self-repair or non-professional

repair can have safety consequences and might

void the guarantee.

• The following spare parts will be available for 7

years after the model has been discontinued:

motor, circulation and drain pump, heaters and

heating elements, including heat pumps, piping

and related equipment including hoses, valves,

ﬁlters and aquastops, structural and interior

parts related to door assemblies, printed circuit

boards, electronic displays, pressure switches,

thermostats and sensors, software and ﬁrmware

including reset software. Please note that some

of these spare parts are only available to

professional repairers, and that not all spare

parts are relevant for all models.

• The following spare parts will be available for 10

years after the model has been discontinued:

door hinge and seals, other seals, spray arms,

drain ﬁlters, interior racks and plastic peripherals

such as baskets and lids.

DISPOSAL

WARNING! Risk of injury or

suffocation.

• Disconnect the appliance from the mains

supply.

• Cut off the mains cable and discard it.

• Remove the door catch to prevent children and

pets to get closed in the appliance.

CONTROL PANEL

1 32

456

Display

Indicators

On/off button

Delay button

XtraDry button

Programme buttons

INDICATORS

Indicator Description

Washing phase. It comes on when the washing phase operates.

Drying phase. It comes on when the drying phase operates.

End indicator.

Rinse aid indicator. It is always off while the programme operates.

Salt indicator. It is always off while the programme operates.

PROGRAMMES

The numbering of the programmes in the table (P1,

P2, etc.) reﬂects their sequence on the control

panel.

The order of the programmes in the table may not

reﬂect their sequence on the control panel.

Programme

Degree of soil

Type of load

Programme phases

Consumption values

1)2)

Duration

(min)

Energy

(kWh)

Water

(l)

Eco

Normal soil

Crockery and

cutlery

• Prewash

• Wash 50 °C

• Rinses

• Dry

237

227

0.920

0.936

9.9

AUTOMATIC

All

Crockery, cut-

lery, pots and

pans

• Prewash

• Wash from

45 °C to

70 °C

• Rinses

• Dry

120 - 170 0.694 -

1.223

9 - 12.8

Intensive

Heavy soil

Crockery, cut-

lery, pots and

pans

• Prewash

• Wash 70 °C

• Rinses

• Dry

160 1.052 -

1.285

11.1 -

13.6

Quick 30Min

Fresh soil

Crockery and

cutlery

• Wash 60 °C

or 65 °C

• Rinses

30 0.556 -

0.680

9.2 - 11.2

Delicate

Normal or light

soil

Delicate crock-

ery and glass-

ware

• Wash 45 °C

• Rinses

• Dry

105 0.792 -

0.968

10.5 -

12.8

Rinse and Hold

All • Prewash 15 0.012 -

0.015

3.4 - 4.2

1) The pressure and the temperature of the water, the variations of the mains supply, the options and the

quantity of dishes can change the values.

2) The values for programmes other than ECO are indicative only.

3) This programme offers the most efﬁcient use of water and energy consumption for crockery and cutlery

with normal soil. This is the standard programme for test institutes. This programme is used to assess

compliance with the Ecodesign Comission Regulation (EU) 2019/2022.

4) In accordance with the 1016/2010 regulation.

5) In accordance with the 2019/2022 regulation.

6) The appliance senses the degree of soil and the quantity of items in the baskets. It automatically adjusts

the temperature and quantity of water, energy consumption and programme duration.

7) This programme is suitable for washing a load or a half load with fresh or light soil in a short time.

8) With this programme, you can quickly rinse off food remains from dishes and prevent odours forming in

the appliance. Do not use detergent with this programme.

SETTINGS

PROGRAMME SELECTION MODE

In the programme selection mode it is possible to

set a washing programme and to enter the user

mode to change the appliance settings.

To enter the programme selection mode, press on/

off.

The appliance is in programme selection mode

when, after activation, the display shows the

number of the programme Eco. The programme

duration appears on the display a couple of

seconds after.

If the control panel does not indicate that the

appliance is in programme selection mode,

implement the CANCEL procedure.

CANCEL FUNCTION

Use CANCEL to:

• CANCEL the currently running programme.

• Stop the countdown of the Delay option.

• Bring the appliance back to the programme

selection mode.

To CANCEL, press and hold

and until the

appliance is in programme selection mode.

USER MODE

User mode allows to change the following settings:

• Adjust the level of the water softener according

to the water hardness.

• Activate or deactivate the rinse aid empty

notiﬁcation.

• Activate or deactivate AirDry.

Before entering user mode, make sure the

appliance is in programme selection mode:

1. Press and hold

and .

• The indicators , and ﬂash.

As the appliance stores the saved settings, there is

no need to conﬁgure it before every cycle.

THE WATER HARDNESS TABLE

The water softener removes minerals from the water

supply, which would have a negative effect on the

washing results and on the appliance.

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. It is important to set the right

level of the water softener to assure good washing

results.

Water hardness

German degrees

(°dH)

French degrees

(°fH)

mmol/l

Clarke de-

grees

Water softener level

47 - 50 84 - 90 8.4 - 9.0 58 - 63 10

43 - 46 76 - 83 7.6 - 8.3 53 - 57 9

37 - 42 65 - 75 6.5 - 7.5 46 - 52 8

29 - 36 51 - 64 5.1 - 6.4 36 - 45 7

23 - 28 40 - 50 4.0 - 5.0 28 - 35 6

19 - 22 33 - 39 3.3 - 3.9 23 - 27

15 - 18 26 - 32 2.6 - 3.2 18 - 22 4

11 - 14 19 - 25 1.9 - 2.5 13 - 17 3

4 - 10 7 - 18 0.7 - 1.8 5 - 12 2

<4 <7 <0.7 < 5

1) Factory setting.

2) Do not use salt at this level.

Regardless of the type of detergent used, set

the proper water hardness level to keep the

salt reﬁll indicator active.

Multi-tabs containing salt are not

effective enough to soften hard water.

Regeneration process

For the correct water softener operation, the resin

of the softener device needs to be regenerated

regularly. This process is automatic and is the part

of the normal dishwasher operation.

When the prescribed quantity of water (see values

in the table) has been used since the previous

regeneration process, a new regeneration process

will be initiated between the ﬁnal rinse and the

programme end.

Water softener level Amount of water (l)

1 250

2 100

3 62

4 47

5 25

6 17

7 10

8 5

9 3

10 3

In case of the high water softener setting, it may

occur also in the middle of the programme, before

the rinse (twice during a programme). Regeneration

initiation has no impact on the cycle duration,

unless it occurs in the middle of a programme or at

the end of a programme with a short drying phase.

In that cases, the regeneration prolongs the total

duration of a programme by additional 5 minutes.

Subsequently, the rinsing of the water softener that

lasts 5 minutes may begin in the same cycle or at

the beginning of the next programme. This activity

increases the total water consumption of a

programme by additional 4 litres and the total

energy consumption of a programme by additional

2 Wh. The rinsing of the softener ends with a

complete drain.

Each performed softener rinse (possible more than

one in the same cycle) may prolong the programme

duration by another 5 minutes when it occurs at any

point at the beginning or in the middle of a

programme.

All the consumption values mentioned

in this section are determined in

accordance with the currently

applicable standard in laboratory

conditions with water hardness

2.5mmol/L according to the

2019/2022 regulation (water softener:

level 3).

The pressure and the temperature of

water as well as the variations of the

mains supply can change the values.

ADJUSTING THE WATER SOFTENER

Make sure that the appliance is in user mode:

1. Press

• The indicators and are off.

• The indicator still ﬂashes.

• The display shows the current setting: e.g.

= level 5.

2. Press to change the setting. Each pressing

increases the level number by one. After

reaching level 10, the countdown starts again

from level 1.

3. Press on/off to conﬁrm the setting.

If you use multi-tabs containing salt

and the hardness of your water is

lower than 21°dH, you can set the

lowest water softener level. It

deactivates the salt reﬁll indicator.

If you use standard detergent or multi-

tabs without salt, set the proper water

hardness level to keep the salt reﬁll

indicator active.

DEACTIVATING THE RINSE AID EMPTY

NOTIFICATION

Make sure that the appliance is in user mode:

1. Press .

• The indicators and are off.

• The indicator ﬂashes.

• The display shows the current setting:

– = rinse aid empty notiﬁcation

activated.

– = rinse aid empty notiﬁcation

deactivated.

2. Press to change the setting.

3. Press on/off to conﬁrm the setting.

When rinse aid chamber is empty, the

rinse aid indicator is on prompting to

reﬁll the rinse aid. If you are using

multi-tabs containing rinse aid and you

are satisﬁed with the drying result, you

can deactivate the notiﬁcation.

However, we recommend that you

always use rinse aid for best drying

performance.

If you use standard detergent or multi-

tabs without rinse aid, activate the

notiﬁcation to keep the rinse aid reﬁll

indicator active.

DEACTIVATING AIRDRY

AirDry improves the drying results with less energy

consumption.

While the drying phase operates, the

device opens the appliance door. The

door is then kept ajar.

By default, AirDry is activated with all programmes

excluding Rinse and Hold (if applicable), but it is

possible to deactivate it.

Make sure the appliance is in user mode.

1. Press

• The indicators and are off.

• The indicator ﬂashes.

• The display shows the current setting:

–

= AirDry activated.

– =AirDry deactivated.

2. Press to change the setting.

3. Press on/off to conﬁrm the setting.

CAUTION! If children have access to

the appliance, it is advised to

deactivate AirDry as opening the door

may pose a danger.

BEFORE FIRST USE

1. Make sure that the current level of the

water softener agrees with the hardness

of the water supply. If not, adjust the level

of the water softener. Contact your local

water authority to know the water

hardness in your area.

2. Fill the salt container with special salt for

dishwasher.

3. Fill the rinse aid dispenser with special rinse

aid for dishwasher.

4. Open the water tap.

5. Start a programme to remove any processing

residuals that can still be inside the appliance.

Do not use detergent and do not load the

baskets.

ADDING SALT

Before the ﬁrst use, put one litre of water in the salt container.

CAUTION! Water and salt can come out of the salt container during ﬁlling. To prevent

corrosion, start a programme immediately after ﬁlling the salt container.

ADDING RINSE AID

The rinse aid helps to dry the dishes without streaks and stains. It is automatically released during the hot

rinse phase.

DAILY USE

1. Open the water tap.

2. Press the on/off button to activate the

appliance.

Make sure that the appliance is in programme

selection mode.

• If the salt indicator is on, ﬁll the salt

container.

• If the rinse aid indicator is on, ﬁll the rinse

aid dispenser.

3. Load the baskets.

4. Add the detergent.

5. Set and start the correct programme for the

type of load and the degree of soil.

ADDING DETERGENT

If the programme has a prewash phase, put a small quantity of detergent on the inner part of the appliance

door.

ADDING MULTI-TABLETS

• Adjust the water softener to the lowest level.

THE AUTO OFF FUNCTION

This function decreases energy consumption by

deactivating automatically the appliance when it is

not operating.

The function comes into operation:

• 5 minutes after the completion of the

programme.

• After 5 minutes if the programme has not

started.

STARTING A PROGRAMME

1. Keep the appliance door ajar.

2. Press the on/off button to activate the

appliance. Make sure that the appliance is in

programme selection mode.

3. Press one of the programme buttons until the

display shows the number of the desired

programme. The display shows the programme

duration after some seconds.

4. Set the applicable options.

5. Close the appliance door to start the

programme.

XTRADRY OPTION

Activate this option when you want to boost the

drying performance. With the use of this option, the

duration of some programmes, water consumption

and the last rinse temperature can be affected.

The XtraDry option is a permanent option for all

programmes other than Eco and need not to be

selected at every cycle.

DELAY OPTION

1. Set a programme.

2. Press Delay until the display shows the delay

time you want to set (1-24h).

The delay time ﬂashes in the display.

3. Close the appliance door. The countdown

starts to decrease by 1 hour.

When the countdown is complete the programme

starts.

OPENING THE DOOR WHILE THE

APPLIANCE OPERATES

Opening the door while a programme is running

stops the appliance. It may affect the energy

consumption and the programme duration. After

closing the door, the appliance continues from the

point of interruption.

If the door is opened during the drying

phase, before AirDry automatically

opens it, the programme ends after 30

seconds.

If the door is closed after it is opened

automatically by AirDry in the drying

phase, the programme ends after 3

minutes.

Do not try to close the appliance door

within 2 minutes after AirDry

automatically opens it, as this may

cause damage to the appliance.

END OF THE PROGRAMME

When the programme is complete, the display

shows: 0:00.

• Press on/off or wait 5 minutes for the Auto OFF

function to automatically deactivate the

appliance.

• Close the water tap.

If you open the door before the

activation of Auto OFF, the appliance

is automatically deactivated.

HINTS AND TIPS

GENERAL

Follow the hints below to ensure optimal cleaning

and drying results in daily use and to protect the

environment.

• Washing dishes in the dishwasher as instructed

in the user manual usually consumes less water

and energy than washing dishes by hand.

• Load the dishwasher to its full capacity to save

water and energy. For best cleaning results,

arrange items in the baskets as instructed in the

user manual and do not overload the baskets.

• Do not pre-rinse dishes by hand. It increases

the water and energy consumption. When

needed, select a programme with a prewash

phase.

• Remove larger residues of food from the dishes

and empty cups and glasses before putting

them inside the appliance.

• Soak or slightly scour cookware with ﬁrmly

cooked-on or baked-on food before washing it

in the appliance.

• Make sure that items in the baskets do not

touch or cover each other. Only then can the

water completely reach and wash the dishes.

• You can use dishwasher detergent, rinse aid

and salt separately or you can use the multi-

tablets (e.g. ''All in 1''). Follow the instructions

on the packaging.

• Select a programme according to the type of

load and the degree of soil. Eco offers the most

efﬁcient use of water and energy consumption.

• To prevent limescale buildup inside the

appliance:

– Reﬁll the salt container whenever

necessary.

– Use the recommended dosage of the

detergent and rinse aid.

– Make sure that the current level of the water

softener agrees with the hardness of the

water supply.

– Follow the instructions in the chapter "Care

and cleaning".

THE WATER SOFTENER

The water softener removes minerals from the water

supply, which would have a detrimental effect on

the washing results and on the appliance.

The higher the content of these minerals, the harder

your water is. Water hardness is measured in

equivalent scales.

The water softener should be adjusted according to

the hardness of the water in your area. Your local

water authority can advise you on the hardness of

the water in your area. It is important to set the right

level of the water softener to assure good washing

results.

USING SALT, RINSE AID AND DETERGENT

• Only use salt, rinse aid and detergent for

dishwasher. Other products can cause damage

to the appliance.

• In areas with hard and very hard water we

recommend to use plain dishwasher detergent

(powder, gel, tablets containing no additional

agents), rinse aid and salt separately for optimal

cleaning and drying results.

• At least once a month run the appliance with the

use of appliance cleaner which is particularly

suitable for this purpose.

• Detergent tablets do not fully dissolve with short

programmes. To prevent detergent residues on

the tableware, we recommend that you use the

tablets with long programmes.

• Always use the correct quantity of detergent.

Insufﬁcient dosage of detergent can result in

poor cleaning results and hard-water ﬁlming or

spotting on the items. Using too much detergent

with soft or softened water results in detergent

residues on the dishes. Adjust the amount of

detergent based on the water hardness. Refer

to the instructions on the detergent packaging.

• Always use the correct quantity of rinse aid.

Insufﬁcient dosage of rinse aid decreases the

drying results. Using too much rinse aid results

in bluish layers on the items.

• Make sure that the water softener level is

correct. If the level is too high, the increased

quantity of salt in the water might result in rust

on cutlery.

WHAT TO DO IF YOU WANT TO STOP USING

MULTI-TABLETS

Before you start to use separately detergent, salt

and rinse aid do the following procedure.

1. Set the highest level of the water softener.

2. Make sure that the salt and rinse aid containers

are full.

3. Start the shortest programme with a rinsing

phase. Do not add detergent and do not load

the baskets.

4. When the programme is completed, adjust the

water softener according to the water hardness

in your area.

5. Adjust the released quantity of rinse aid.

6. Activate the rinse aid empty notiﬁcation.

LOADING THE BASKETS

• Always use the whole space of the baskets.

• Only use the appliance to wash items that are

dishwasher-safe.

• Do not wash in the appliance items made of

wood, horn, aluminium, pewter and copper as

they could crack, warp, get discoloured or

pitted.

• Do not wash in the appliance items that can

absorb water (sponges, household cloths).

• Remove remaining food from the items.

• Make soft the remaining burned food on the

items.

• Put hollow items (cups, glasses and pans) with

the opening down.

• Make sure that cutlery and dishes do not bond

together. Mix spoons with other cutlery.

• Make sure that glasses do not touch other

glasses.

• Put light items in the upper basket. Make sure

that the items do not move.

• Make sure that the spray arm can move freely

before you start a programme.

BEFORE STARTING A PROGRAMME

Before you start the selected programme, make

sure that:

• The ﬁlters are clean and correctly installed.

• The cap of the salt container is tight.

• The spray arms are not clogged.

• There is enough salt and rinse aid (unless you

use multi-tablets).

• The arrangement of the items in the baskets is

correct.

• The programme is suitable to the type of load

and the degree of soil.

• The correct quantity of detergent is used.

UNLOADING THE BASKETS

1. Let the tableware cool down before you

remove it from the appliance. Hot items can be

easily damaged.

2. First remove items from the lower basket, then

from the upper basket.

After the programme is completed,

water can still remain on the inside

surfaces of the appliance.

CARE AND CLEANING

WARNING! Before maintenance,

deactivate the appliance and

disconnect the mains plug from the

main socket.

Dirty ﬁlters and clogged spray arms

decrease the washing results. Make a

check regularly and, if necessary, clean

them.

CLEANING THE FILTERS

• Make sure that there are no residues of food or soil in or around the edge of the sump.

• Put back in place the ﬂat ﬁlter (C). Make sure that it is correctly positioned under the 2 guides.

• Reassemble the ﬁlters (A) and (B).

• Put back the ﬁlter (A) in the ﬂat ﬁlter (C). Turn it clockwise until it locks.

An incorrect position of the ﬁlters can cause bad washing results and damage to the

appliance

CLEANING THE SPRAY ARMS

Do not remove the spray arms. If the holes in the

spray arms are clogged, remove remaining parts of

soil with a thin pointed object.

EXTERNAL CLEANING

• Clean the appliance with a moist soft cloth.

• Only use neutral detergents.

• Do not use abrasive products, abrasive cleaning

pads or solvents.

INTERNAL CLEANING

• Carefully clean the appliance, including the

rubber gasket of the door, with a soft damp

cloth.

• If you regularly use short duration programmes,

these can leave deposits of grease and

limescale inside the appliance. To prevent this,

we recommend to run long duration

programmes at least 2 times per month.

• To maintain the performance of your appliance

at its best, we recommend to use monthly a

speciﬁc cleaning product for dishwashers.

Follow carefully the instructions on the

packaging of the product.

REMOVAL OF FOREIGN OBJECTS

Check the ﬁlters and the sump after each use of the

dishwasher. Foreign objects (e.g. pieces of glass,

plastic, bones or toothpicks, etc) decrease the

cleaning performance and can cause damage to

the drain pump.

1. Disassemble the ﬁlters system as instructed in

this chapter.

2. Remove any foreign objects by hand.

CAUTION! If unable to remove the

objects, contact an Authorised

Service Centre.

3. Reassemble the ﬁlters as instructed in this

chapter.

TROUBLESHOOTING

WARNING! Improper repair of the

appliance may pose a danger to the

safety of the user. Any repairs must be

performed by qualiﬁed personnel.

The majority of problems that may occur can

be solved without the need to contact an

Authorised Service Centre.

Refer to the below table for information on possible

problems.

With some problems, the display shows an alarm

code.

Problem and alarm code Possible cause and solution

You cannot activate the appli-

ance.

• Make sure that the mains plug is connected to the mains sock-

et.

• Make sure that there is no damaged fuse in the fuse box.

The programme does not start. • Make sure that the appliance door is closed.

• If the delay start is set, cancel the setting or wait for the end of

the countdown.

• The appliance recharges the resin inside the water softener.

The duration of the procedure is approximately 5 minutes.

The appliance does not ﬁll with

water.

The display shows i10 or i11.

• Make sure that the water tap is open.

• Make sure that the pressure of the water supply is not too low.

For this information, contact your local water authority.

• Make sure that the water tap is not clogged.

• Make sure that the ﬁlter in the inlet hose is not clogged.

• Make sure that the inlet hose has no kinks or bends.

The appliance does not drain

the water.

The display shows i20.

• Make sure that the sink spigot is not clogged.

• Make sure that the interior ﬁlter system is not clogged.

• Make sure that the drain hose has no kinks or bends.

The anti-ﬂood device is on.

The display shows i30.

• Close the water tap.

• Make sure that the appliance is correctly installed.

• Make sure the baskets are loaded as instructed in the user

manual.

Malfunction of the water level

detection sensor.

The display shows i41 - i44.

• Make sure that the ﬁlters are clean.

• Switch the appliance off and on.

Malfunction of the wash pump

or the drain pump.

The display shows i51 - i59 or

i5A - i5F.

• Switch the appliance off and on.

The temperature of the water

inside the appliance is too high

or malfunction of the tempera-

ture sensor occurred.

The display shows i61 or i69.

• Make sure that the temperature of the inlet water does not ex-

ceed 60°C.

• Switch the appliance off and on.

Technical malfunction of the

appliance.

The display shows iC0 or iC3.

• Switch the appliance off and on.

The level of water inside the

appliance is too high.

The display shows iF1.

• Switch the appliance off and on.

• Make sure that the ﬁlters are clean.

• Make sure that the outlet hose is installed at the right height

above the ﬂoor. Refer to the installation instructions.

The appliance stops and starts

more times during operation.

• It is normal. It provides optimal cleaning results and energy sav-

ings.

The programme lasts too long. • If the delayed start option is set, cancel the delay setting or wait

for the end of the countdown.

Problem and alarm code Possible cause and solution

The remaining time in the dis-

play increases and skips nearly

to the end of programme time.

• This is not a defect. The appliance is working correctly.

Small leak from the appliance

door.

• The appliance is not levelled. Loosen or tighten the adjustable

feet (if applicable).

• The appliance door is not centred on the tub. Adjust the rear

foot (if applicable).

The appliance door is difﬁcult

to close.

• The appliance is not levelled. Loosen or tighten the adjustable

feet (if applicable).

• Parts of the tableware are protruding from the baskets.

Rattling/knocking sounds from

inside the appliance.

• The tableware is not properly arranged in the baskets. Refer to

basket loading leaﬂet.

• Make sure that the spray arms can rotate freely.

The appliance trips the circuit-

beaker.

• The amperage is insufﬁcient to supply simultaneously all the ap-

pliances in use. Check the socket amperage and the capacity

of the meter or turn off one of the appliances in use.

• Internal electrical fault of the appliance. Contact an Authorised

Service Centre.

Refer to "Before ﬁrst use", "Daily

use", or "Hints and tips" for other

possible causes.

Once you have checked the appliance, deactivate

and activate the appliance. If the problem occurs

again, contact an Authorised Service Centre.

For alarm codes not described in the table, contact

an Authorised Service Centre.

WARNING! We do not recommend

using the appliance until the problem

has been completely ﬁxed. Unplug the

appliance and do not plug it in again

until you are certain that it operates

correctly.

THE WASHING AND DRYING RESULTS ARE NOT SATISFACTORY

Problem Possible cause and solution

Poor washing results. • Refer to "Daily use", "Hints and tips" and basket loading

leaﬂet.

• Use more intensive washing programmes.

• Clean spray arm jets and ﬁlter. Refer to "Care and Clean-

ing".

Problem Possible cause and solution

Poor drying results. • Tableware has been left for too long inside a closed appli-

ance.

• There is no rinse aid or the dosage of rinse aid is not enough.

Set the rinse aid dispenser to a higher level.

• Plastic items may need to be towel dried.

• For the best drying performance activate the option XtraDry

and set AirDry.

• We recommend to always use rinse aid, even in combination

with multi-tablets.

There are whitish streaks or blu-

ish layers on glasses and dishes.

• The release quantity of rinse aid is too much. Adjust the rinse

aid level to a lower level.

• The quantity of detergent is too much.

There are stains and dry water

drops on glasses and dishes.

• The released quantity of rinse aid is not sufﬁcient. Adjust the

rinse aid level to a higher level.

• The quality of the rinse aid can be the cause.

The dishes are wet. • For the best drying performance activate the option XtraDry

and set AirDry .

• The programme does not have a drying phase or has a drying

phase with low temperature.

• The rinse aid dispenser is empty.

• The quality of the rinse aid can be the cause.

• The quality of the multi-tablets can be the cause. Try a differ-

ent brand or activate the rinse aid dispenser and use rinse

aid and multi-tablets together.

The interior of the appliance is

wet.

• This is not a defect of the appliance. it is caused by the hu-

midity in the air that condenses on the walls.

Unusual foam during washing. • Use the detergent for dishwashers only.

• There is a leak in the rinse aid dispenser. Contact an Author-

ised Service Centre.

Traces of rust on cutlery. • There is too much salt in the water used for washing. Refer to

"The water softener".

• Silver and stainless steel cutlery were placed together. Avoid

to put silver and stainless steel items close together.

There are residues of detergent

in the dispenser at the end of the

programme.

• The detergent tablet got stuck in the dispenser and therefore

was not completely washed away by water.

• Water cannot wash away the detergent from the dispenser.

Make sure that the spray arm is not blocked or clogged.

• Make sure that items in the baskets do not impede the lid of

the detergent dispenser from opening.

Odours inside the appliance. • Refer to "Internal cleaning".

Problem Possible cause and solution

Limescale deposits on the table-

ware, on the tub and on the in-

side of the door.

• The level of salt is low, check the reﬁll indicator.

• The cap of the salt container is loose.

• Your tap water is hard. Refer to "The water softener".

• Even using multi-functional tabs use salt and set regeneration

of the water softener. Refer to "The water softener".

• If lime scale deposits still remain, clean the appliance with

appliance cleaners which are particularly suitable for this pur-

pose.

• Try different detergent.

• Contact the detergent manufacturer.

Dull, discoloured or chipped ta-

bleware.

• Make sure that only dishwasher-safe items are washed in the

appliance.

• Load and unload the basket carefully. Refer to basket loading

leaﬂet.

• Place delicate items in the upper basket.

Refer to "Before ﬁrst use", "Daily

use" or "Hints and tips" for other

possible causes.

TECHNICAL INFORMATION

Dimensions Width / height / depth (mm) 596 / 818 - 898 / 575

Electrical connection

1) Voltage (V) 220 - 240

Frequency (Hz) 50

Water supply pressure Min. / max. bar (MPa) 0.5 (0.05) / 8 (0.8)

Water supply

Cold water or hot water

2) max 60 °C

Capacity Place settings 13

Power consumption Left-on mode (W) 5.0

Off-mode (W) 0.50

1) Refer to the rating plate for other values.

2) If the hot water comes from alternative source of energy (e.g. solar panels), use the hot water supply to

decrease energy consumption.

LINK TO THE EU EPREL DATABASE

The QR code on the energy label supplied with the

appliance provides a web link to the registration of

this appliance in the EU EPREL database. Keep

the energy label for reference together with the

user manual and all other documents provided with

this appliance.

It is possible to ﬁnd information related to the

performance of the product in the EU EPREL

database using the link https://eprel.ec.europa.eu

and the model name and product number that you

can ﬁnd on the rating plate of the appliance. Refer

to the chapter "Product description".

For more detailed information about the energy

label, visit www.theenergylabel.eu.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the

packaging in relevant containers to recycle it. Help

protect the environment and human health by

recycling waste of electrical and electronic

appliances. Do not dispose of appliances marked

with the symbol with the household waste.

Return the product to your local recycling facility or

contact your municipal ofﬁce.

VISITEZ NOTRE SITE WEB POUR :

Obtenir des conseils d’utilisation, des brochures, un dépanneur, des informations sur le

service et les réparations :

www.zanussi.com/support

INFORMATIONS DE SÉCURITÉ

Avant d'installer et d'utiliser cet appareil, lisez soigneusement les

instructions fournies. Le fabricant ne pourra être tenu pour

responsable des blessures et dégâts résultant d'une mauvaise

installation ou utilisation. Conservez toujours les instructions dans

un lieu sûr et accessible pour vous y référer ultérieurement.

SÉCURITÉ DES ENFANTS ET DES PERSONNES

VULNÉRABLES.

• Cet appareil peut être utilisé par des enfants âgés d'au moins

8 ans et par des personnes ayant des capacités physiques,

sensorielles ou mentales réduites ou dénuées d’expérience ou

de connaissance, s'ils sont correctement surveillés ou si des

instructions relatives à l'utilisation de l'appareil en toute sécurité

leur ont été données et s’ils comprennent les risques encourus.

• Les enfants entre 3 et 8 ans et les personnes ayant un

handicap très important et complexe doivent être tenus à l'écart

de l'appareil, à moins d'être surveillés en permanence.

• Les enfants de moins de 3 ans doivent être tenus à l'écart de

l'appareil, à moins d'être surveillés en permanence.

• Ne laissez pas les enfants jouer avec l'appareil.

• Ne laissez pas les détergents à la portée des enfants.

• Tenez les enfants et les animaux éloignés de l'appareil lorsque

la porte est ouverte.

• Le nettoyage et l'entretien ne doivent pas être effectués par des

enfants sans surveillance.

SÉCURITÉ GÉNÉRALE

• Cet appareil est conçu uniquement pour un usage domestique

et des situations telles que :

– bâtiments de ferme, cuisines réservées aux employés dans

les magasins, bureaux et autres lieux de travail ;

La page charge ...

Zanussi ZDI26022XA Manuel utilisateur

Marque: Zanussi

Modèle: ZDI26022XA

Catégorie: Lave-vaisselle

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Zanussi ZDI26022XA User manual

Zanussi ZDI26022XA Manuel utilisateur

Zanussi ZDI26022XA Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents