Real Flame C1460LP Le manuel du propriétaire

C1460LP Berthoud Fire Pit NG Conversion Kit

Improper installation, adjustment,

alteration, service or maintenance

can cause property damage

personal injury, or loss of life.

Read the installation, operation

and maintenance instructions

thoroughly before installing or

servicing this equipment.

!

IMPORTANT

WARNING

SAVE THESE INSTRUCTIONS

!

DANGER

If you smell gas:

gas to the appliance.

2. Extinguish any open ﬂ ame.

3. If odor continues, keep away from the appliance and

immediately call your gas supplier or ﬁ re department.

USC

For Technical Support Please Contact Real Flame® At: 1-800-654-1704

PARTS LIST 00023105G

1

2

3

NATURAL GAS CONVERSION KIT

NOTE

This conversion kit is for changing a Liqueﬁed Petroleum (LP) ﬁre table into a Natural Gas

ﬁre table.

!

WARNING

!

Natural Gas Hose and Quick Disconnect

NG Oriﬁce Spud 3.9mm

Primary Air Mixer Sleeve

4

5

Conversion Plaque

Cable Kit

3

1

2

5

1

• If the information in these instructions is not followed exactly, a ﬁre, explosion or

production of carbon monoxide may result causing property damage, personal injury

or loss of life.

• The qualiﬁed service agency is responsible for the proper installation of this kit. The

installation is not proper and complete until the operations of the converted appliance

is checked as speciﬁed in the manufacturer’s instructions supplied with this kit.

• This conversion kit shall be installed by a qualiﬁed service agency in accordance with

Real Flame’s instructions and all applicable codes and requirements of the authority

having jurisdiction.

#3.9mm

C1460LP

50,000 BTU/Hr. (14.65 kW)

NATURAL GAS CONVERSION

2

2.) Disconnect LP hose from valve.

1.) Flip the ﬁre pit upside down. Place on a soft surface to avoid damaging

the ﬁnish.

NATURAL GAS CONVERSION

3

3.) Disconnect bellows (Corrugated Stainless Steel Tube/CSST) from

burner base.

Bellows

4

NATURAL GAS CONVERSION

4.) Remove the existing LP oriﬁce spud.

LP Oriﬁce Spud

5

NATURAL GAS CONVERSION

5.) Locate the new NG oriﬁce spud, verify it is the correct number.

The sign 3.9 mm should be on the end of the oriﬁce spud.

6.) Slip sleeve over primary air opening. See ﬁg. 1.

Next, screw the new NG oriﬁce spud into the burner base. See ﬁg. 2.

3.9

Sleeve

Primary Air

Opening

NG Oriﬁce Spud

1 2

6

NATURAL GAS CONVERSION

7.) Re-attach bellows (CSST) to new spud.

Bellows

7

8.) Attach NG hose to the input side of the valve.

9.) Attach quick disconnect to gas supply.

NATURAL GAS CONVERSION

House Natural Gas Piping

Shut-o Valve

Quick Disconnect Socket

NG Gas Hose

To Fire Table

10.) After installing the conversion kit, verify the location of the

thermocouple and igniter Pin using the illustration below.

Installing at Altitude

For installations at elevations above 2,000 ft., contact your local dealer or gas

supplier before installing because input rating should be reduced

approximately 4% for each 1,000 ft. above sea level. Refer to the National Fuel

Gas Code. Contact Real Flame for more information at 1-800-654-1704.

11.) Note to installation technicians: Verify the manifold pressure by using a

3/8” ﬂared T-junction at the location marked by the arrow below. Then, using

a digital manometer, verify that the pressure before the oriﬁce is 7” W.C. Also

verify that the oriﬁce spud has the 3.9 mm stamp. This will allow you to verify

that the input rating of the appliance is correct.

NATURAL GAS CONVERSION

8

NOTE: Igniter housing removed for example only.

To Manometer

5mm

Thermocouple

Igniter

13.) Cut the existing French plaque from the control panel using wire cutters. Re-attach

French plaque and NG conversion plaque included with this kit to the ﬁre pit using

the included cable kit.

Cut Cable

Re-attach both plaques

NOTE: The normal manifold pressure for this converted appliance is 7” water column.

NOTE: The maximum inlet gas pressure for this unit is 10.5 in W.C. (2.61 kPa).

The minimum inlet gas pressure for this unit is 3.5 in W.C. (0.87 kPa).

NATURAL GAS CONVERSION

WARNING

!

Check for leaks at these locations

12. CHECKING FOR LEAKS

Make a leak check solution by mixing 1 part dishwashing soap

with 3 parts water in a spray bottle.

Make sure the re pit control knob is “OFF.” Then, turn the natural

gas on at its source.

Spray leak solution on the valve connections, paying particular

attention to the areas indicated by the arrows.

If any bubbles appear turn the natural gas o at its source,

reconnect and re-test. If you continue to see bubbles after several

attempts, disconnect the natural gas source and contact Real

Flame

® at 1-800-654-1704 for assistance.

If no bubbles appear after one minute, turn the gas

source “OFF”, wipe away solution and proceed to next

step.

9

Before using this outdoor ﬁre pit, make sure you have read, understand and are following all

information provided in the Important Safety Information section of this manual. Failure to

follow those instructions can cause property damage, serious injury or death.

French

NG

Conv.

14.) Lighting

Lighting Instructions

LIGHT

LOW

Control Knob

PUSH

IN

8-13”

20.3 - 30.5 cm

10

1. Read and understand all operating instructions before lighting.

2. Burner control knob must be in the OFF position.

3. Ensure that gas supply is connected and open.

4. Push and hold igniter button to create sparks.

5. While holding the igniter button with one hand, use your other

hand to push and turn the control knob to the LIGHT position

to ignite the burner.

6. Keep burner control knob pressed in for 15-30 seconds

after ignition.

7. If ignition does not occur in 15 seconds, turn control knob to

the OFF position and turn gas o at the source; wait 5

minutes until gas has cleared and repeat lighting procedure.

8. After lighting, rotate the burner control knob counter

clockwise to LOW setting. Observe ﬂame; to make sure all

burner ports are lit.

9. Adjust the ﬂame to the desired height with the

control knob. Flames should be between 8-13” in height.

1. Wearing heat-resistant gloves, position the burning

long match or extended lighter near the side of

the burner. DO NOT lean over the ﬁre pit while

lighting.

2. Turn control knob counterclockwise to LIGHT.

3. Remove long match/extended lighter.

4. After lighting, rotate the burner control knob counter

clockwise to LOW setting. Observe ﬂame; make sure

all burner ports are lit.

5. Adjust the ﬂame to the desired height with the

control knob.

6. Replace the battery as soon as possible.

When using this method to light your ﬁre pit use heat-resistant gloves and follow the step-

by-step instructions. Failure t

o do so could result in severe injury.

If burner ﬂame goes out during operation, immediately turn the control knob OFF position and

let the gas clear a minimum of 5 minutes before attempting to re-light the ﬁre pit.

Using the Igniter

!

WARNING

If battery is dead you may TEMPORARILY use

a long match or extended butane lighter

If doing so:

NOTES AND TECHNICAL SUPPORT

Type of Gas / Type de gaz: NG/Natural Gas

Normal Hourly Input/Entrée horaire normal:

50,000 BTU/Hr. (14.65 kW)

Manifold Pressure/Pression d'admission:

7.0” water column (1.74 kPa)

The minimum inlet pressure for this ﬁre table is:

3.5” water column (0.87 kPa)

The maximum inlet pressure for this ﬁre table is:

10.5” water column (2.61 kPa)

®

USC

This appliance was converted on _________________

(DD/MM/YY)

to Natural Gas with Kit No._______________________

(Found on Box)

by___________________________________________,

(Name and address of organization making this conversion)

which accepts the responsibility that this conversion has

been properly made.

For additional technical support call: 1-800-654-1704

Cet appareil a été converti le

en gaz naturel avec le kit no.

par

NOTES: ______________________________________________________

_____________________________________________________________

11

Une mauvaise installation,

d’ajustement, modiﬁcation,

service ou d’entretien peut

causer des blessures ou des

dommages matériels.

Lisez l’installation, l’opération et

des instructions de maintien à

fond avant

stallation ou

entretien de cet équipement.

!

IMPORTANT

!

DANGER

immédiatement votre fournisseur de gaz ou le service des incendies.

C SU

our le support technique veuillez contacter ame à

AVERTISSEMENT

CONSERVEZ CES INSTRUCTIONS

Kit de conversion NG de C1460LP Berthoud table-foyer

LISTE DES PIECES 00023105G

1

2

3

KIT DE CONVERSION DU GAZ NATUREL

NOTE

Ce kit de conversion est pour changer un table de feu de Pétrole Liquéﬁé (LP) dans une

table de feu de Gaz naturel.

!

Tuyau de gaz naturel et déconnexion rapide

Patate d’oriﬁce NG # 3.9 mm

Gaine de mixage d’air principal

4

5

Plaque de Conversion

Kit de câble

3

1

2

5

!

AVERTISSEMENT

1

• Si l’information dans ces instructions n’est pas suivi exactement, un incendie, une

explosion ou la production de monoxyde de carbone peut causer des dommages

matériels, des blessures corporelles ou la pertes de vie.

• Le service d’entretien qualiﬁé est responsable de l’installation appropriée de ce kit.

L’installation n’est pas bon et complet jusqu’à la fonctionnement de l’appareil converti

est contrôlé comme spéciﬁé dans les instructions du fabricant fournies avec ce kit.

• Ce kit de conversion doit être installé par un service d’entretien qualiﬁé con aux

instructions du Real Flame et tous les codes applicables et les exigence l’autorité

ayant la Juridiction.

C1460LP

50,000 BTU/Hr. (14.65 kW)

#3.9mm

CONVERSION DU GAZ NATUREL

2

1.) Retournez la foyer sur son côté. Placez sur une surface souple pour

éviter d’endommager la ﬁnition.

2.) Débranchez le tuyau LP de la valve.

CONVERSION DU GAZ NATUREL

3

3.)

Débrancher le souet (Tubes en acier inoxydable ondulé/CSST)

de la base de brûleur.

Souets

4

CONVERSION DU GAZ NATUREL

4.)

Oriﬁce de patate LP

5

CONVERSION DU GAZ NATUREL

5.)

numéro. Le numéro 3.9 mm devrait être sur l’extrémité d’oriﬁce de patate.

6.)

issez le gaine sur l’ouverture aérienne princi ir ﬁg.

Ensuite, vissez la nouvelle patate d iﬁce N ans la base de brûleur.

ir fig.

3.9

Gaine

L’ouverture

d’air principal

Patate d’oriﬁce NG

1 2

6

CONVERSION DU GAZ NATUREL

7.) Rattachez les souets (CSST) à la nouvelle patate.

Souets

7

8.)

9.)

CONVERSION DU GAZ NATUREL

Tuyauterie de Gaz naturel de Maison

Soupape d'arrêt

Prise de déconnexion rapide

Tuyau de Gaz NG

Au Table de Feu

La page charge ...

Real Flame C1460LP Le manuel du propriétaire

Ce manuel convient également à

Real Flame C1460LP Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents