Sub-Zero IW-30A-RH Le manuel du propriétaire

Marque: Sub-Zero

Modèle: IW-30A-RH

Catégorie: Boissons glacées

Taper: Le manuel du propriétaire

Ce manuel convient également à

WINE STORAGE

USE AND CARE GUIDE

CLEANING, MAINTENANCE, AND MORE

Sub-Zero Customer Care 800.222.7820

WINE STORAGE

Contents

4 Wine Storage Features

5 Interactive Control Panel

6 Storage

8 Operation

10 Care Recommendations

11 Technical Data

13 Troubleshooting

15 Sub-Zero Warranty

subzero.com

Customer Care

The model and serial number are printed on the enclosed

product registration card. Both numbers are also listed on

the product rating plate. Refer to page 4 for rating plate

location. For warranty purposes, you will also need the date

of installation and name of your authorized Sub-Zero dealer.

Record this information below for future reference.

SERVICE INFORMATION

Model Number

Serial Number

Date of Installation

Certied Service Name

Certied Service Number

Authorized Dealer

Dealer Number

If your product ever needs attention, be sure to use a

Sub-Zero Factory Certied Service provider recommended

by our customer care center, or select one from our list of

providers available at subzero.com/locator. All Factory Certi-

ed Service providers are carefully selected and thoroughly

trained by us.

WINE STORAGE

Important Note

To ensure this product is installed and operated as safely

and efciently as possible, take note of the following types

of highlighted information throughout this guide:

IMPORTANT NOTE highlights information that is especially

important.

CAUTION indicates a situation where minor injury or product

damage may occur if instructions are not followed.

WARNING states a hazard that may cause serious injury or

death if precautions are not followed.

IMPORTANT NOTE: Throughout this guide, dimensions in

parentheses are millimeters unless otherwise specied.

WARNING

PROPOSITION 65 FOR CALIFORNIA RESIDENTS

Cancer and Reproductive Harm—

www.P65Warnings.ca.gov

Sub-Zero Customer Care 800.222.7820

WINE STORAGE FEATURES

Wine Storage Features

FEATURES

Product Rating Plate

Interactive Control Panel

Wine Storage Racks

Display Rack

Full-View Glass Door

Home Security Connection

Refrigerator Storage Drawer

Freezer Storage Drawer*

Water Filtration System*

Automatic Ice Maker*

*Not available on all models.

Column model

Tall model (IW-30CI shown)

subzero.com

Interactive Control Panel

For initial start up, touch and hold ‘power’ on the control

panel for 2 seconds.

Temperature can be adjusted in one-degree increments

on the home screen. All wine storage models have sepa-

rate temperature controls for each zone. Temper atures are

preset at 45°F

(7°C) for the lower zone and 55°F (13°C) for

the upper zone. Storage drawers are preset at 38°F

(3°C) for

refrigerator and 0°F

(-18°C) for freezer.

To change the temperature, touch the temperature being

adjusted, then press ‘+’ or ‘-’ until desired temperature is

displayed. Refer to the illustration below.

Once the temperature has been adjusted, additional

features can be activated or deactivated from the options

screen. Touch

to view the options screen.

OPTIONS SCREEN

Touch to activate or deactivate door/drawer alarm.

Touch to activate accent lighting.

Touch to activate humidor feature.*

Touch to adjust drawer temperature.*

Touch to activate or deactivate ice maker system and

max ice feature.*

Touch to view settings screen.

*Not available on all models.

SETTINGS SCREEN

Touch to view model information.

Touch to select temperature unit, Fahrenheit or Celsius.

Touch to adjust control panel brightness and contrast.

Touch to adjust door/drawer alarm volume and pitch.

Touch to adjust door/drawer alarm duration.

Touch to activate humidor feature.*

Touch to enter Sabbath mode.

Touch to view troubleshooting and service information.

Touch to set clock.

Touch to select smart home options.

Touch to select language options.

Touch to adjust soft on lighting.

*Not available on all models.

INTERACTIVE CONTROLS

Home screen

Sub-Zero Customer Care 800.222.7820

Wine Storage

WINE RACKS

The full-extension wine racks provide easy access to

750 ml, half-bottles and magnums. When storing magnums,

the rack above must be removed.

To remove a wine rack, pull out to full extension, tilt up,

then lift up and out. Refer to the illustration below. The top

two racks in the upper compartment and top rack (top two

for tall model) in the lower compartment cannot be placed

in any other position. These racks can be identied by the

small square cut-out located in the right rear corner. Refer to

the illustration below.

The natural cherrywood facing on wine racks can be stained

or replaced with wood to compliment cabinetry. For more

information, refer to the Sub-Zero design guide, visit our

website at subzero.com or contact Sub-Zero customer care

at 800-222-7820.

CAUTION

Remove all bottles from the wine rack before removal.

DISPLAY RACK

The adjustable display rack is designed for wine to stay in

contact with the cork at any position. Refer to the illustration

below.

To remove the display rack, pull out to full extension, tilt up,

then lift up and out.

STORAGE

Display rack

CUT-OUT

Wine rack removal

Rack position indicator

subzero.com

ICE CONTAINER

To remove the ice container, pull the freezer drawer open

until it stops, then lift the container out. Refer to the illustra-

tion below.

The ice maker must be turned off by touching

when

the ice container is removed. The unit is equipped with a

3-minute delay after the ice container has been removed, to

ensure cubes are not ejected before the ice maker can be

deactivated or ice container is reinstalled.

Storage Drawers—Tall Model

DRAWER DIVIDERS

To remove or adjust a short divider, ex the long divider

slightly, then pull upward. Refer to the illustration below.

To remove a long divider, the short dividers must be

removed. Pull the divider up until it stops, rotate counter-

clockwise, then pull upward. To reinstall, align grooves with

drawer tabs, rotate clockwise, then slide down.

DRAWER REMOVAL

To remove, pull open until the drawer stops. Raise the

drawer front and pull out the drawer. To reinstall, raise the

front of the drawer and place onto the slides. Align the back

of the drawer with hooks on the slide, then align the white

pegs at the front of the slide with holes at the front of the

drawer. Refer to the illustration below.

Drawer dividers

Drawer removal

STORAGE

Ice container (IW-30CI)

Sub-Zero Customer Care 800.222.7820

WATER FILTER REPLACEMENT

1 To access the water lter, pull out on the bottom edge

of the access door and rotate upward. Refer to the illus-

tration below.

2 To remove the old lter, rotate counterclockwise one-

quarter turn, then pull out. It is normal for a small amount

of water to drip when the lter is removed. It should be

wiped up with a paper towel or cloth.

3 Remove the new lter from packaging and remove

plastic cap.

4 Insert the new lter into the manifold and turn clockwise.

5 Once the new lter has been installed, follow instructions

on the control panel. The lter life cycle will reset for

approximately one year.

Water Filtration System

For model IW-30CI, the water ltration system supplies

ltered water to the ice maker.

IMPORTANT NOTE: When using the water ltration system

for the rst time and after lter replacement, it is necessary

to clear any air from the system and allow the lter to assist

in cleaning the water lines. Discard the rst two full con-

tainers of ice.

If the water ltration system will not be utilized, it can be

placed in water lter bypass mode by removing the lter.

The lter is rated for 750 gallons

(2839 L) or one year,

whichever comes rst. ‘Change Water Filter’ will appear on

the control panel when the cartridge needs to be replaced.

Touch ‘Snooze’ to delay reminder for 24 hours or until lter

can be replaced.

Replacement Sub-Zero water lters can be ordered online

at subzerowolfstore.com. For questions, contact Sub-Zero

customer care at 800-222-7820.

OPERATION

WATER FILTER

ACCESS DOOR

Water lter removal (IW-30CI)

subzero.com

OPERATION

Ice Maker Operation

For model IW-30CI, to initiate ice production, touch

on the options screen. A single highlighted cube indicates

the ice maker is active. Three highlighted cubes indicate the

max ice feature is active. Max ice increases ice production

up to 30% for a 24-hour period. During that period, some

components may run at a higher speed resulting in a unique

audible tone. This is typical and will revert back after 24

hours or when the ice container is full. To deactivate the ice

maker, touch

until no cubes are highlighted. After initial

start-up, discard the rst few batches of ice. The ice may

contain impurities from new plumbing connections.

If ice is not used regularly it may fuse together. To avoid,

discard ice and allow ice maker to replenish.

The ice maker must be turned off by touching

when

the ice container is removed. The unit is equipped with a

3-minute delay after the ice container has been removed, to

ensure cubes are not ejected before the ice maker can be

deactivated or ice container is reinstalled.

Sabbath

This appliance is certied by Star-K to meet strict religious

regulations in conjunction with specic instructions found

on www.star-k.org.

For Sabbath mode, from the settings screen, touch

and

follow instructions on the control panel.

Sub-Zero Customer Care 800.222.7820

Cleaning

INTERIOR CLEANING

To clean interior surfaces and all removable parts, wash with

a mild solution of soap, water and baking soda. Rinse and

dry thoroughly. Avoid getting water on lights, control panel

and the cherrywood facing on wine racks.

Use a standard glass cleaner to clean the UV-resistant glass

door.

CAUTION

Do not use vinegar, rubbing alcohol or other alcohol-

based cleaners on any interior surface.

STAINLESS STEEL EXTERIOR

Use a nonabrasive stainless steel cleaner and apply with a

soft lint-free cloth. To bring out the natural luster, lightly wipe

surface with a water-dampened microber cloth followed by

a dry polishing chamois. Always follow the grain of stainless

steel.

CONDENSER CLEANING

CAUTION

Before cleaning the condenser, turn power off at the

control panel. Wear gloves to avoid injury from sharp

condenser ns.

The condenser is located behind the grille. Remove the

kickplate by extracting the two mounting screws. Refer to

the illustration below. Use a soft bristle brush and vacuum

to remove dust and lint from the condenser. Clean the con-

denser every three to six months.

IMPORTANT NOTE: To avoid damaging condenser ns,

vacuum in the direction of the ns.

CAUTION

Failure to clean the condenser could result in tempera-

ture loss, mechanical failure or damage.

CONDENSER

SCREW

Condenser location

CARE RECOMMENDATIONS

subzero.com

TECHNICAL DATA

Sub-Zero Water Filtration System Data

REPLACEMENT CARTRIDGE (4204490)

Tested and certied by NSF International against NSF/ANSI Standard 42 for the reduction of Chlorine Taste & Odor,

Particulate Class I; and against NSF/ANSI Standard 53 for the reduction of Lead, Mercury, Atrazine, Benzene, Carbofuran,

1,4-dichlorobenzene, Lindane, Toxaphene, Turbidity, Cysts and Asbestos.

OPERATING SPECIFICATIONS

Capacity: certied for up to 750 gallons (2,838 L); up to twelve months

Pressure Requirement: 35 – 120 psi (2.8 – 8.2 bar)

Temperature: 33 – 100°F (0.6 – 38°C)

Flow Rate: 0.78 gpm (2.9 Lpm)

NSF

Standard

Inuent Challenge

Concentration

Average Inuent

Concentration

Product Water Concentration % Reduction

Max Permissable

Product Water

ConcentrationSubstance Average Max Efuent Average Minimum

Chlorine, Taste & Odor 42 2.0 mg/L ± 10% 1.88 mg/L 0.05 mg/L 0.06 mg/L 97.34% 96.80% ≥ 50%

Particulate 42

At least 10,000

particles/ml

5,700,000/ml 30,583/ml 69,000/ml 99.46% 98.78% ≥ 85%

Lead at pH 6.5 53 0.15 mg/L ± 10% 0.153 mg/L <0.001 mg/L <0.001 mg/L 99.34% 99.34% 0.010 mg/L

Lead at pH 8.5 53 0.15 mg/L ± 10% 0.150 mg/L <0.001 mg/L <0.001 mg/L 99.33% 99.33% 0.010 mg/L

Mercury at pH 6.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0003 mg/L 0.0005 mg/L 95.00% 91.66% 0.002 mg/L

Mercury at pH 8.5 53 0.006 mg/L ± 10% 0.006 mg/L 0.0008 mg/L 0.0015 mg/L 86.66% 75.00% 0.002 mg/L

Atrazine 53 0.009 mg/L ± 10% 0.009 mg/L <0.002 mg/L <0.002 mg/L 77.77% 77.77% 0.003 mg/L

Benzene 53 0.015 mg/L ± 10% 0.014 mg/L 0.0006 mg/L 0.0011 mg/L 95.71% 92.14% 0.005 mg/L

Carbofuran 53 0.08 mg/L ± 10% 0.081 mg/L <0.001 mg/L <0.001 mg/L 98.76% 98.76% 0.04 mg/L

1,4-dichlorobenzene 53 0.225 mg/L ± 10% 0.208 mg/L <0.0005 mg/L <0.0005 mg/L 99.75% 99.75% 0.075 mg/L

Lindane 53 0.002 mg/L ± 10% 0.002 mg/L 0.00003 mg/L 0.00007 mg/L 98.50% 96.50% 0.0002 mg/L

Toxaphene 53 0.015 mg/L ± 10% 0.015 mg/L <0.001 mg/L <0.001 mg/L 93.33% 93.33% 0.003 mg/L

Turbidity 53 11 ± 1 NTU 10.7 NTU 0.31 NTU 0.49 NTU 97.10% 95.42% 0.5 NTU

Cysts** 53 Minimum 50,000/L 166,500/L <1/L <1/L >99.99% >99.99% >99.95%

Asbestos 53 10

to 10

bers/L

†

155 MF/L <1 MF/L <1 MF/L >99.99% >99.99% >99%

**Based on the use of Cryptosporidium Parvum oocysts † Fibers greater than 10 μm in length

• Do not use with water that is microbiologically unsafe or of unknown

water quality without adequate disinfection before or after the

system.

• Systems certied for cyst reduction may be used on disinfected

waters that may contain lterable cysts.

• This system must be installed, operated, maintained and lters

replaced as required in order for the product to perform as adver-

tised.

• Note that while the testing was performed under standard labora-

tory conditions, actual performance may vary. The contaminants

or other substances removed or reduced by this water treatment

system are not necessarily in your water.

SPECIAL NOTES

• Replacement Sub-Zero water lter cartridges can be ordered online

at subzerowolfstore.com. For questions, contact Sub-Zero customer

care at 800-222-7820.

• Change lter cartridge at least every twelve months. High sediment

areas may require more frequent lter cartridge replacement.

• Installation and operation instructions, parts and service availability,

and standard warranty are included with the product when

shipped.

• Replace water lter cartridge when the lter indicator is lit or when

water ow becomes too low. Use replacement water lter cartridge

part number 4204490. Replacement lter pricing information can be

found at subzero.com.

Manufactured for: Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744, 800-222-7820

This system has been tested according to NSF/ANSI 42/53 for reduc-

tion of the substances listed below. The concentration of the indicated

substances in water entering the system was reduced to a concentra-

tion less than or equal to the permissible limit for water leaving the

system, as specied in NSF/ANSI 42/53.

Sub-Zero Customer Care 800.222.7820

TECHNICAL DATA

subzero.com

TROUBLESHOOTING

High temperatures, unit runs excessively or unit giving

off too much heat.

• Verify condenser is clean.

• Verify door/drawer is closing properly.

• Verify door/drawer has not been left ajar.

• Increased ambient temperatures may cause compres-

sors to run longer.

• If temperature display shows 45° and 55°, but is not

cooling, unit may be in showroom mode. Contact

Sub-Zero Customer Care at 800-222-7820.

ODOR

• Unit should be cleaned before using for the rst time.

This will clear any odors that may have been trapped

during shipping.

• Uncovered food could create odor which may require

cleaning.

Troubleshooting

SERVICE INDICATOR

ashes in control panel display.

• Verify condenser is clean.

• Turn unit off at the control panel, then on. If indicator

continues to ash, contact Sub-Zero Factory Certied

Service.

UNIT OPERATION

No lights or cooling.

• Verify power is on.

• Verify electrical power to unit and home circuit breaker

is on.

No lights.

• Door/drawer may have been left ajar which has disabled

lights to eliminate excess heat. If lights are out, close

door/drawer for one hour. If lights are still out, contact

Sub-Zero Factory Certied Service.

• Cabinet lighting must be replaced by Sub-Zero Factory

Certied Service.

Frost, condensation or ice build up inside unit.

• Verify condenser is clean.

• Verify door/drawer is closing properly.

• Verify door/drawer has not been left ajar.

• Verify door/drawer gasket does not have rips or tears. If

it does, contact Sub-Zero Factory Certied Service.

• If icing is heavy, turn unit off and use a hair dryer to melt

ice. Hair dryer should be set on low and kept moving

at all times. Once ice has melted, wipe up water with a

cloth or paper towel.

Sub-Zero Customer Care 800.222.7820

TROUBLESHOOTING

Troubleshooting

ICE PRODUCTION

No ice.

• Verify ice cube indicator appears in control panel display.

• Verify ice maker has been on for at least 24 hours.

• Verify freezer temperature near 0°F.

• Verify ice container is properly installed.

• Verify ice maker arm in down position.

• Verify water is being supplied to unit.

• Verify water lter has been replaced within the last 12

months and installed properly.

• Verify water lter has been removed if a reverse osmosis

ltration system is being utilized.

Blue or green ice.

• Possible copper supply line corrosion. Contact plumber

to clean or replace.

Black ecks in cubes.

• Stop use and contact Sub-Zero Factory Certied

Service.

Bad taste.

• Defrost freezer and clean with soap and water.

• Place coffee grounds or charcoal briquettes in freezer to

absorb odor.

Hollow cubes.

• Clean condenser. Contact Sub-Zero Factory Certied

Service if unresolved.

SERVICE

• Maintain the quality built into your product by contacting

Sub-Zero Factory Certied Service. For the name of the

nearest Sub-Zero Factory Certied Service, check the

Support and Service section of our website, subzero.com

or call Sub-Zero customer care at 800-222-7820.

• When contacting service, you will need the model and

serial number of your unit. Both numbers are listed on

the product rating plate. Refer to page 4 for rating plate

location.

• For warranty purposes, you will also need the date

of installation and name of your authorized Sub-Zero

dealer. This information should be recorded on page 3.

Sub-Zero, Sub-Zero & Design, Sub-Zero & Snowake Design, Dual Refrigeration, The Living Kitchen, Great American Kitchens The Fine Art of Kitchen Design, Wolf, Wolf &

Design, Wolf Gourmet, W & Design, red colored knobs, Cove, and Cove & Design are registered trademarks and service marks of Sub-Zero Group, Inc. and its subsidiaries.

All other trademarks are property of their respective owners in the United States and other countries.

Sub-Zero Residential Limited Warranty

FOR RESIDENTIAL USE

FULL TWO YEAR WARRANTY*

For two years from the date of original installation, this Sub-Zero product warranty covers all parts and

labor to repair or replace, under normal residential use, any part of the product that proves to be defec-

tive in materials or workmanship. All service provided by Sub-Zero under the above warranty must be

performed by Sub-Zero factory certied service, unless otherwise specied by Sub-Zero, Inc. Service will

be provided during normal business hours.

FULL FIVE YEAR SEALED SYSTEM WARRANTY

For ve years from the date of original installation, this Sub-Zero product warranty covers all parts and

labor to repair or replace, under normal residential use, these parts that prove to be defective in materials

or workmanship: compressor, condenser, evaporator, drier and all connecting tubing. All service provided

by Sub-Zero under the above warranty must be performed by Sub-Zero factory certied service, unless

otherwise specied by Sub-Zero, Inc. Service will be provided during normal business hours.

LIMITED TWELVE YEAR SEALED SYSTEM WARRANTY

For twelve years from the date of original installation, Sub-Zero will repair or replace the following parts

that prove to be defective in materials or workmanship: compressor, condenser, evaporator, drier and all

connecting tubing. If the owner uses Sub-Zero factory certied service, the service provider will repair or

replace these parts with the owner paying for all other costs, including labor. If the owner uses non-certi-

ed service, the owner must contact Sub-Zero, Inc. (using the information below) to receive repaired or

replacement parts. Sub-Zero will not reimburse the owner for parts purchased from non-certied service

or other sources.

TERMS APPLICABLE TO EACH WARRANTY

The warranty applies only to products installed for normal residential use. The warranty applies only to

products installed in any one of the fty states of the United States, the District of Columbia or the ten

provinces of Canada. This warranty does not cover any parts or labor to correct any defect caused by

negligence, accident or improper use, maintenance, installation, service or repair.

THE REMEDIES DESCRIBED ABOVE FOR EACH WARRANTY ARE THE ONLY ONES THAT SUB-ZERO, INC.

WILL PROVIDE, EITHER UNDER THIS WARRANTY OR UNDER ANY WARRANTY ARISING BY OPERATION OF

LAW. SUB-ZERO, INC. WILL NOT BE RESPONSIBLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES

ARISING FROM THE BREACH OF THIS WARRANTY OR ANY OTHER WARRANTY, WHETHER EXPRESS,

IMPLIED OR STATUTORY.

Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you. This warranty gives you specic legal rights and you may also

have other legal rights that vary from state to state.

To receive parts and/or service and the name of Sub-Zero factory certied service nearest you, contact

Sub-Zero, Inc., P.O. Box 44848, Madison, WI 53744; check the contact & support section of our website,

subzero.com, email us at [email protected] or call 800-222-7820.

*Stainless steel (doors, panels, handles, product frames and interior surfaces) are covered by a limited

60-day parts and labor warranty for cosmetic defects.

*Replacement water lters and air purication cartridges are not covered by the product warranty.

Atención al cliente de Sub-Zero 800.222.7820

ALMACENAMIENTO DE VINOS

Contenido

4 Funciones de la unidad para almacenamiento de vinos

5 Panel de control interactivo

6 Almacenamiento

8 Operación

10 Recomendaciones para el cuidado

11 Datos técnicos

13 Resolución de problemas

15 Garantía de Sub-Zero

subzero.com

Atención al cliente

El modelo y número de serie están impresos en la tarjeta

de registro del producto adjunta. Los dos números también

aparecen en la placa de datos del producto. Consulte la

página 4 para encontrar la placa de datos. Para nes de la

garantía, usted también necesitará la fecha de instalación y

el nombre de su distribuidor autorizado de Sub-Zero. Anote

esta información abajo para referencia futura.

INFORMACIÓN PARA SERVICIO

Número de modelo

Número de serie

Fecha de instalación

Nombre de servicio certicado

Número de servicio certicado

Distribuidor autorizado

Número de distribuidor

Si su producto alguna vez necesita servicio, asegúrese de

usar un proveedor de servicios certicado por Sub-Zero y

recomendado por nuestro centro de atención al cliente, o

seleccione uno de nuestra lista de proveedores disponibles

en subzero.com/locator. Todos los proveedores de servicio

certicados de fábrica han sido cuidadosamente seleccio-

nados y entrenados a fondo por nosotros.

ALMACENAMIENTO DE VINOS

Aviso importante

Para garantizar que este producto se instale y opere de

la forma más segura y eciente posible, tome nota de los

siguientes tipos de información resaltada en esta guía:

AVISO IMPORTANTE señala la información que es especial-

mente importante.

PRECAUCIÓN indica una situación en la que se pueden

sufrir heridas leves o provocar daños al producto si no se

siguen las instrucciones.

ADVERTENCIA indica peligro de que se produzcan heridas

graves o incluso la muerte si no se siguen las precauciones.

AVISO IMPORTANTE: En toda esta guía, las dimensiones

entre paréntesis son milímetros, a menos que se especi-

que lo contrario.

ADVERTENCIA

PROPUESTA 65 PARA RESIDENTES DE CALIFORNIA

Cáncer y Daño Reproductivo—

www.P65Warnings.ca.gov

Atención al cliente de Sub-Zero 800.222.7820

FUNCIONES DE LA UNIDAD PARA ALMACENAMIENTO DE VINOS

Funciones de la unidad para almacenamiento

de vinos

CARACTERÍSTICAS

Placa de datos del producto

Panel de control interactivo

Estantes para almacenamiento de vinos

Estante para exhibición.

Puerta de cristal de vista completa

Conexión al sistema de seguridad del hogar

Cajón de almacenamiento del refrigerador

Cajón de almacenamiento del congelador*

Sistema de ltrado de agua*

Fábrica automática de hielo*

*No está disponible en todos en modelos.

Modelo de columna

Modelo alto (el modelo mostrado es el IW-30CI)

subzero.com

Panel de control interactivo

Para la puesta en marcha inicial, toque y mantenga presio-

nado el botón "power" (encendido) en el panel de control

durante 2 segundos.

La temperatura puede ajustarse en incrementos de un

grado desde la pantalla de inicio. Todos los modelos de

almacenamiento de vino tienen diferentes controles de

temperatura para cada zona. Las temperaturas están pre-

establecidas a 45°F

(7°C) para la zona inferior y 55°F (13°C)

para la zona superior. Los cajones de almacenamiento están

congurados a 38°F

(3°C) para el refrigerador y a 0°F (-18°C)

para el congelador.

Para cambiar la temperatura, toque la temperatura que

desea ajustar, luego presione "+" o "-" hasta que aparezca

la temperatura deseada. Consulte la siguiente ilustración.

Una vez que ha ajustado la temperatura, puede activar o

desactivar otras funciones desde la pantalla de ajustes.

Toque

para ver la pantalla de opciones.

PANTALLA DE OPCIONES

Toque para activar o desactivar la alarma de la puerta o

del cajón.

Toque para activar la luz de acento.

Toque para activar la función del humidicador.*

Toque para ajustar la temperatura del cajón.*

Toque para activar o desactivar el sistema de fabricación

de hielo y la función max ice.*

Toque para ver la pantalla de ajustes.

*No está disponible en todos en modelos.

PANTALLA DE AJUSTES

Toque para ver la información del modelo.

Toque para seleccionar la unidad de temperatura,

Fahrenheit o Celsius.

Toque para ajustar el brillo y contraste del panel de

control.

Toque para ajustar el volumen y tono de la alarma de la

puerta y del cajón.

Toque para ajustar la duración de la alarma de la puerta

y del cajón.

Toque para activar la función del humidicador.*

Toque para iniciar el modo Sabbath.

Toque para ver cómo solucionar problemas y la informa-

ción del servicio técnico.

Toque para programar el reloj.

Toque para seleccionar opciones de inicio inteligente.

Toque para seleccionar opciones de idioma.

Toque para ajustar la luz de acento suave.

*No está disponible en todos en modelos.

CONTROLES INTERACTIVOS

Pantalla de inicio

Atención al cliente de Sub-Zero 800.222.7820

Almacenamiento de vinos

ESTANTES PARA VINO

Los estantes de extensión completa permiten un fácil

acceso a botellas de 750 ml, medias botellas y magnas.

Cuando se almacenen botellas magnas (dobles) se debe

retirar el estante superior.

Para retirar un estante para almacenar vinos, extiéndalo

completamente, inclínelo hacia arriba, luego levántelo hacia

arriba y hacia fuera. Consulte la siguiente ilustración. Los

dos estantes superiores en el compartimento superior y el

estante superior (los dos superiores para el modelo alto) en

el compartimento inferior no se pueden colocar en ninguna

otra posición. Estos estantes se pueden identicar por el

pequeño recorte cuadrado ubicado en la esquina trasera

derecha. Consulte la siguiente ilustración.

El revestimiento de madera de cerezo en los estantes para

almacenar vinos se puede reemplazar con madera para

complementar los gabinetes. Para más información, con-

sulte la guía de diseños de Sub-Zero, visite nuestra página

de Internet en subzero.com o comuníquese con la línea de

atención al cliente de Sub-Zero al 800-222-7820.

PRECAUCIÓN

Retire todas las botellas del estante para almacenar

vinos antes de quitar el estante.

ESTANTE PARA EXHIBICIÓN

El estante de exhibición ajustable está diseñado para que el

vino esté en contacto con el corcho en cualquier posición.

Consulte la siguiente ilustración.

Para retirar el estante de exhibición, extiéndalo completa-

mente, inclínelo hacia arriba, luego levántelo hacia arriba y

hacia fuera.

ALMACENAMIENTO

RECORTE

Retiro del estante para vinos

Indicador de posición de la

rejilla

Estante para exhibición

La page charge ...

Sub-Zero IW-30A-RH Le manuel du propriétaire

Marque: Sub-Zero

Modèle: IW-30A-RH

Catégorie: Boissons glacées

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Sub-Zero IW-30A-RH Owner's manual
español: Sub-Zero IW-30A-RH El manual del propietario

Sub-Zero IW-30A-RH Le manuel du propriétaire

Ce manuel convient également à

Sub-Zero IW-30A-RH Le manuel du propriétaire

dans d''autres langues

Documents connexes