Generac Centurion 3250 G0061041 Manuel utilisateur

Marque: Generac

Modèle: Centurion 3250 G0061041

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Owner's Manual

Portable Generator

MODEL: 006104-1

AUTHORIZED DEALER SUPPORT:



DEADLY EXHAUST FUMES! ONLY use OUTSIDE

far away from windows, doors and vents!



NOT INTENDED FOR USE IN CRITICAL LIFE

SUPPORT APPLICATIONS.



SAVE this Manual. Provide this manual to any

operator of the generator.

Table of Contents

Introduction ............................................................. 1

Read this Manual Thoroughly ................................. 1

Safety Rules ...........................................................1

Standards Index .............................................................3

General Information ................................................ 4

1.1 Unpacking ......................................................................4

1.1.1 Accessory Box ..................................................4

1.2 Assembly .......................................................................4

1.2.1 Assembling the Accessory Kit............................4

1.3 Emission Information .....................................................4

Operation ................................................................ 5

2.1 Know the Generator .......................................................5

2.2 Cord Sets and Connection Plugs ....................................6

2.2.1 120 VAC Duplex Receptacle ...............................6

2.2.2 120/240 VAC, 20 Amp Twistlock Receptacle ......6

2.3 How to Use the Generator ..............................................6

2.3.1 Grounding the Generator When Used

as a Portable .....................................................7

2.3.2 Connecting the Generator to a Building's

Electrical System ...............................................7

2.3.3 Connecting Electrical Loads ...............................7

2.4 Don’t Overload the Generator ..........................................7

2.5 Wattage Reference Guide ...............................................7

2.6 Before Starting the Generator .........................................8

2.6.1 Adding Engine Oil ..............................................8

2.6.2 Adding Gasoline .................................................8

2.7 To Start the Engine .........................................................9

2.8 Stopping the Engine .......................................................9

2.9 Low Oil Level Shutdown System ....................................9

2.9.1 Sensing Low Oil Level ........................................9

Maintenance ........................................................... 9

3.1 Maintenance Schedule ...................................................9

3.2 Product Specifications ..................................................10

3.2.1 Generator Specifications ..................................10

3.2.2 Engine Specifications .......................................10

3.3 General Recommendations ...........................................10

3.3.1 Generator Maintenance ....................................10

3.3.2 To Clean the Generator .....................................10

3.3.3 Engine Maintenance .........................................10

3.3.4 Checking Oil Level ...........................................10

3.3.5 Changing the Oil ..............................................10

3.3.6 Replacing the Spark Plug .................................11

3.3.7 Spark Arrestor .................................................11

3.4 Service Air Filter ...........................................................11

3.5 Valve Clearance ............................................................12

3.6 General ........................................................................12

3.7 Long Term Storage .......................................................12

3.8 Other Storage Tips .......................................................12

Troubleshooting .................................................... 13

4.1 Troubleshooting Guide ..................................................13

Warranty ............................................................... 14

Manual del propietario ..................................... 17

Manuel d'entretien ............................................ 35

WARNING!

California Proposition 65

Engine exhaust and some of its constituents are known to the state of California to cause cancer,

birth defects, and other reproductive harm.

WARNING!

California Proposition 65

This product contains or emits chemicals known to the state of California to cause cancer,

birth defects, and other reproductive harm.

INTRODUCTION

Thank you for purchasing this model by Generac Power Systems,

Inc. This model is a compact, high performance, air-cooled,

engine driven generator designed to supply electrical power to

operate electrical loads where no utility power is available or in

place of utility due to a power outage.

READ THIS MANUAL THOROUGHLY

If any portion of this manual is not understood, contact the nearest

Authorized Dealer for starting, operating and servicing procedures.

The operator is responsible for proper and safe use of the

equipment. We strongly recommend that the operator read this

manual and thoroughly understand all instructions before using the

equipment. We also strongly recommend instructing other users to

properly start and operate the unit. This prepares them if they need

to operate the equipment in an emergency.

The generator can operate safely, efficiently and reliably only if it

is properly located, operated and maintained. Before operating or

servicing the generator:

• Become familiar with and strictly adhere to all local, state and

national codes and regulations.

• Study all safety warnings in this manual and on the product

carefully.

• Become familiar with this manual and the unit before use.

The manufacturer cannot anticipate every possible circumstance

that might involve a hazard. The warnings in this manual, and on

tags and decals affixed to the unit are, therefore, not all inclusive.

If using a procedure, work method or operating technique that the

manufacturer does not specifically recommend, ensure that it is

safe for others. Also make sure the procedure, work method or

operating technique utilized does not render the generator unsafe.

THE INFORMATION CONTAINED HEREIN WAS BASED ON

MACHINES IN PRODUCTION AT THE TIME OF PUBLICATION.

GENERAC RESERVES THE RIGHT TO MODIFY THIS MANUAL AT

ANY TIME.

SAFETY RULES

Throughout this publication, and on tags and decals affixed to the

generator, DANGER, WARNING, CAUTION and NOTE blocks are

used to alert personnel to special instructions about a particular

operation that may be hazardous if performed incorrectly or

carelessly. Observe them carefully. Their definitions are as follows:

INDICATES A HAZARDOUS SITUATION OR

ACTION WHICH, IF NOT AVOIDED, WILL RESULT

IN DEATH OR SERIOUS INJURY.

Indicates a hazardous situation or action which,

if not avoided, could result in death or serious

injury.

Indicates a hazardous situation or action which,

if not avoided, could result in minor or moderate

injury.

NOTE:

Notes contain additional information important to a procedure

and will be found within the regular text body of this manual.

These safety warnings cannot eliminate the hazards that they

indicate. Common sense and strict compliance with the special

instructions while performing the action or service are essential to

preventing accidents.

Introduction

Four commonly used safety symbols accompany the DANGER,

WARNING and CAUTION blocks. The type of information each

indicates is as follows:



This symbol points out important safety

information that, if not followed, could

endanger personal safety and/or property of

others.





This symbol points out potential explosion

hazard.



This symbol points out potential fire hazard.



This symbol points out potential electrical

shock hazard.

GENERAL HAZARDS

• NEVER operate in an enclosed area, in a vehicle, or indoors

EVEN IF doors and windows are open.

• For safety reasons, the manufacturer recommends that the

maintenance of this equipment is carried out by an Authorized

Dealer. Inspect the generator regularly, and contact the nearest

Authorized Dealer for parts needing repair or replacement.

• Operate generator only on level surfaces and where it will not be

exposed to excessive moisture, dirt, dust or corrosive vapors.

• Keep hands, feet, clothing, etc., away from drive belts, fans,

and other moving parts. Never remove any fan guard or shield

while the unit is operating.

• Certain parts of the generator get extremely hot during

operation. Keep clear of the generator until it has cooled to

avoid severe burns.

• Do NOT operate generator in the rain.

• Do not alter the construction of the generator or change

controls which might create an unsafe operating condition.

• Never start or stop the unit with electrical loads connected

to receptacles AND with connected devices turned ON. Start

the engine and let it stabilize before connecting electrical

loads. Disconnect all electrical loads before shutting down the

generator.

• Do not insert objects through unit’s cooling slots.

• When working on this equipment, remain alert at all times.

Never work on the equipment when physically or mentally

fatigued.

• Never use the generator or any of its parts as a step. Stepping

on the unit can stress and break parts, and may result in

dangerous operating conditions from leaking exhaust gases,

fuel leakage, oil leakage, etc.

NOTE:

This generator is equipped with a spark arrestor muffler. The

spark arrestor must be maintained in effective working order

by the owner/ operator. In the State of California, a spark

arrestor is required by law (Section 4442 of the California

Public Resources Code). Other states may have similar laws.

Federal laws apply on federal lands.

EXHAUST & LOCATION HAZARDS

• Never operate in an enclosed area or indoors! NEVER use in

the home, in a vehicle, or in partly enclosed areas such as

garages, EVEN IF doors and windows are open! ONLY use

outdoors and far from open windows, doors, vents, and in an

area that will not accumulate deadly exhaust.

• The engine exhaust fumes contain carbon monoxide, which

you cannot see or smell. This poisonous gas, if breathed in

sufficient concentrations, can cause unconsciousness or even

death.

• Adequate, unobstructed flow of cooling and ventilating air

is critical to correct generator operation. Do not alter the

installation or permit even partial blockage of ventilation

provisions, as this can seriously affect safe operation of the

generator. The generator MUST be operated outdoors.

• This exhaust system must be properly maintained. Do nothing

that might render the exhaust system unsafe or in noncompliance

with any local codes and/or standards.

• Always use a battery operated carbon monoxide alarm indoors,

installed according to the manufacturer's instructions.

• If you start to feel sick, dizzy, or weak after the generator has

been running, move to fresh air IMMEDIATELY. See a doctor, as

you could have carbon monoxide poisoning.

Safety Rules

ELECTRICAL HAZARDS

• The generator produces dangerously high voltage when in

operation. Avoid contact with bare wires, terminals, connections,

etc., while the unit is running, even on equipment connected to

the generator. Ensure all appropriate covers, guards and barriers

are in place before operating the generator.

• Never handle any kind of electrical cord or device while

standing in water, while barefoot or while hands or feet are wet.

DANGEROUS ELECTRICAL SHOCK MAY RESULT.

• The National Electric Code (NEC) requires the frame and external

electrically conductive parts of the generator be properly

connected to an approved earth ground. Local electrical codes

may also require proper grounding of the generator. Consult

with a local electrician for grounding requirements in the area.

• Use a ground fault circuit interrupter in any damp or highly

conductive area (such as metal decking or steel work).

• Do not use worn, bare, frayed or otherwise damaged electrical

cord sets with the generator.

• Before performing any maintenance on the generator, disconnect

the engine starting battery (if equipped) to prevent accidental

start up. Disconnect the cable from the battery post indicated

by a NEGATIVE, NEG or (–) first. Reconnect that cable last.

• In case of accident caused by electric shock, immediately shut

down the source of electrical power. If this is not possible,

attempt to free the victim from the live conductor. AVOID

DIRECT CONTACT WITH THE VICTIM. Use a non-conducting

implement, such as a rope or board, to free the victim from the

live conductor. If the victim is unconscious, apply first aid and

get immediate medical help.

FIRE HAZARDS

• Gasoline is highly FLAMMABLE and its vapors are EXPLOSIVE.

Do not permit smoking, open flames, sparks or heat in the

vicinity while handling gasoline.

• Never add fuel while unit is running or hot. Allow engine to cool

completely before adding fuel.

• Never fill fuel tank indoors. Comply with all laws regulating

storage and handling of gasoline.

• Do not overfill the fuel tank. Always allow room for fuel

expansion. If tank is over-filled, fuel can overflow onto a hot

engine and cause FIRE or an EXPLOSION. Never store generator

with fuel in tank where gasoline vapors might reach an open

flame, spark or pilot light (as on a furnace, water heater or

clothes dryer). FIRE or EXPLOSION may result. Allow unit to

cool entirely before storage.

• Wipe up any fuel or oil spills immediately. Ensure that no

combustible materials are left on or near the generator. Keep the

area surrounding the generator clean and free from debris and

keep a clearance of five (5) feet on all side to allow for proper

ventilation of the generator.

• Do not insert objects through unit’s cooling slots.

• Do not operate the generator if connected electrical devices

overheat, if electrical output is lost, if engine or generator sparks

or if flames or smoke are observed while unit is running.

• Keep a fire extinguisher near the generator at all times.

STANDARDS INDEX

1. National Fire Protection Association (NFPA) 70: The NATIONAL

ELECTRIC CODE (NEC) available from www.nfpa.org

2. National Fire Protection Association (NFPA) 5000: BUILDING

CONSTRUCTION AND SAFETY CODE available from www.

nfpa.org

3. International Building Code available from www.iccsafe.org

4. Agricultural Wiring Handbook available from www.rerc.org,

Rural Electricity Resource Council P.O. Box 309 Wilmington,

OH 45177-0309

5. ASAE EP-364.2 Installation and Maintenance of Farm Standby

Electric Power available from www.asabe.org, American

Society of Agricultural & Biological Engineers 2950 Niles

Road, St. Joseph, MI 49085

This list is not all inclusive. Check with the Authority Having Local

Jurisdiction (AHJ) for any local codes or standards which may be

applicable to your jurisdiction.

Safety Rules

1.1 UNPACKING

• Remove all packaging material.

• Remove separate accessory box.

• Remove the generator from carton.

1.1.1 ACCESSORY BOX

Check all contents. If any parts are missing or damaged, locate an

authorized dealer at 1-888-436-3722.

• 1 - Owner’s manual

• 1 - Bottle of Oil SAE 30 with funnel

• 3 - Product Registration Cards (English, Spanish, French)

• 2 - 8” WHEELS

• 1 - Axle

• 1 - Frame Foot

• 1 - Handle with grip

• 1 - Hardware Bag

– 1 - Plastic Spacer – 2 - M8-1.25 x 40 Bolts

– 1 - Handle Bracket – 1 - M6-1.0 x 40 Bolt

– 2 - Rubber Bumpers – 2 - M8-1.25 x 16 Bolts

– 2 - Cotter Pins – 1 - M6-1.0 Hex Flange Nut

– 2 - M8-1.25 Hex Flange Nuts

1.2 ASSEMBLY

The generator requires some assembly prior to using it. If

problems arise when assembling the generator, please call the

Generator Helpline at 1-888-436-3722.

The following tools are required to properly assemble the

generator:

• Needle-nose pliers

• Ratchet and 12mm (1/2") socket

• 12mm (1/2") box wrench or adjustable wrench

1.2.1 ASSEMBLING THE ACCESSORY KIT

The wheels are designed for the unit to greatly improve the

portability of the generator.

NOTICE:

The wheels are not intended for over-the-road-use.

1. Refer to Figure 1 to install the wheels as shown.

– Slide the axle through the frame brackets.

– Slide on the wheels then install the cotter pins.

2. Refer to Figure 1 to install the wheel bumpers as shown.

– Secure the two rubber bumpers to the frame foot using

two M8-1.25 Hex Flange Nuts (if not already assembled).

– Place the frame foot under the frame and secure with two

M8-1.25 x 16 bolts.

3. Refer to Figure 2 to install the handle assembly as shown.

– Install the handle bracket to the frame using two M8-1.25

x 40 bolts (if not already assembled).

– Slide the plastic spacer onto the handle assembly then

align with the holes in the handle bracket (if not already

assembled).

– Secure the handle assembly to the handle bracket using

the M6-1.0 x 40 bolt and one M6-1.0 hex flange nut.

Figure 1 – Wheel Assembly

Figure 2 – Handle Kit

M8-1.25 x 40

BOLTS

1 X M6-10 HEX FLANGE NUT

1x HANDLE W/GRIP

1x PLASTIC SPACER

1x M6-1.0X40 BOLT

1x HANDLE BRACKET

1.3 EMISSION INFORMATION

The Environmental Protection Agency requires that this generator

comply with exhaust emission standards. The generator is

certified to meet the applicable EPA emission levels. It is important

that you follow the maintenance specifications provided in this

manual to ensure that your engine complies with the applicable

emission standards for the duration of the engine's life. This engine

is certified to operate on gasoline. The emission control system on

your generator consists of the following:

• Fuel Metering System • Ignition System

– Carburetor

– Spark Plug

– Fuel Lines – Ignition Coil

• Air Induction System

– Intake Pipe/Manifold

– Air Cleaner

The Emissions Compliance Period referred to on the Emissions

Compliance label indicates the number of operating hours for

which the engine has been shown to meet Federal Emissions

requirements.

General Information

2.1 KNOW THE GENERATOR

Read the Owner’s Manual and Safety Rules before operating

this generator.

Compare the generator to Figures 3 through 6 to become

familiarized with the locations of various controls and adjustments.

Save this manual for future reference.

1. 120 Volt AC, 20 Amp, Duplex Receptacle – Supplies electrical

power for the operation of 120 Volt AC, 20 Amp, single-phase,

60 Hz electrical lighting, appliance, tool and motor loads.

2. 120/240V AC, 20 Amp Locking Receptacle – Supplies

electrical power for the operation of 120 and/or 240 volt AC,

20 amp, single-phase, 60 Hz, electrical lighting, appliance,

tool and motor loads.

3. Circuit Breakers (AC) – The control panel is provided with a

2-pole, 14 amp circuit breaker to protect the generator against

electrical overload.

4. Air Filter – Filters intake air as it is drawn into the engine.

5. Choke Knob – Used when starting a cold engine.

6. Fuel Tank – Tank holds 3.35 U.S. gallons of fuel.

7. Grounding Lug – Ground the generator to an approved earth

ground here. See "Grounding the Generator" for details.

8. On/OFF Switch – Controls the operation of the generator.

9. Muffler – Quiets the engine.

10. Handle – Pivot and retract for storage.

11. Gas Cap – Fuel fill location.

12. Fuel Gauge – Shows fuel level in tank.

13. Oil Check/Fill – Check and fill oil here.

14. Recoil Starter – Use to start engine manually.

15. Fuel Shut Off – Valve between fuel tank and carburetor.

16. Oil Drain Plug – Used to drain engine oil.

17. Spark Arrestor – Reduces fire hazard by containing sparks.

18. Roll Over Valve - Passes fuel vapors to the air box.

19. Recovery Hose - Installed between the engine air intake and

the Roll Over Valve.

Figure 3 - Control Panel

Figure 4 - Generator Controls

Figure 5 - Generator Controls

Operation

Figure 6 - Muffler

2.2 CORD SETS AND CONNECTION PLUGS

2.2.1 120 VAC DUPLEX RECEPTACLE

This is a 120 Volt outlet protected against overload by a 14 Amp circuit

breaker (Figure 7). 14 Amps of current may be drawn from each socket,

however, total power drawn must be kept within data plate ratings. Use

only high quality, well insulated, 3-wire grounded cord sets rated for 125

Volts at 20 Amps (or greater).

2.2.2 120/240 VAC, 20A TWISTLOCK RECEPTACLE

This is a 120/240 Volt outlet protected against overload by a 14

Amp circuit breaker (Figure 7). Connect a suitable 4-wire grounded

cord set to the plug and to the desired load. The cord set should

be rated for 250 volts at 20 amps (or greater) if the 120/240

receptacle is used along with 120 volt receptacle. The total load

drawn must not exceed the data label ratings.

Figure 7 - 120 VAC Duplex & 120/240 VAC Twistlock

IMPORTANT: Do not overload the generator. Also, do not overload

individual panel receptacles. These outlets are protected against

overload with circuit breakers. If amperage rating of any circuit

breaker is exceeded, that breaker opens and electrical output

to that receptacle is lost. Read “Don’t Overload the Generator”

carefully.

2.3 HOW TO USE THE GENERATOR

If there are any problems operating the generator, please call the

generator helpline at 1-888-436-3722.



Never operate in an enclosed area or

indoors! NEVER use in the home, in a

vehicle, or in partly enclosed areas such as

garages, EVEN IF doors and windows are

open! ONLY use outdoors and far from open

windows, doors, vents, and in an area that

will not accumulate deadly exhaust.



The engine exhaust fumes contain carbon

monoxide, which can you cannot see or

smell. This poisonous gas, if breathed

in sufficient concentrations, can cause

unconsciousness or even death.



Adequate, unobstructed flow of cooling and

ventilating air is critical to correct generator

operation. Do not alter the installation or

permit even partial blockage of ventilation

provisions, as this can seriously affect safe

operation of the generator. The generator

MUST be operated outdoors.



This exhaust system must be properly

maintained. Do nothing that might render the

exhaust system unsafe or in noncompliance

with any local codes and/or standards.



Always use a battery operated carbon

monoxide alarm indoors, installed according

to the manufacturer's instructions.

Operation

2.3.1 GROUNDING THE GENERATOR WHEN USED AS A

PORTABLE

This generator has an equipment ground that connects the

generator frame components to the ground terminals on the AC

output receptacles (see NEC 250.34 (A) for explanation). This

allows the generator to be used as a portable without grounding

the frame of the generator as specified in NEC 250.34.

Special Requirements

There may be Federal or State Occupational Safety and Health

Administration (OSHA) regulations, local codes, or ordinances that

apply to the intended use of the generator.

Please consult a qualified electrician, electrical inspector, or the

local agency having jurisdiction:

• In some areas, generators are required to be registered with

local utility companies.

• If the generator is used at a construction site, there may be

additional regulations which must be observed.

2.3.2 CONNECTING THE GENERATOR TO A BUILDING’S

ELECTRICAL SYSTEM

When connecting directly to a building's electrical system, it is

recommended that a manual transfer switch is used. Connections for

a portable generator to a building's electrical system must be made by

a qualified electrician and in strict compliance with all national and local

electrical codes and laws.

Figure 8 - Grounding the Generator

2.3.3 CONNECTING ELECTRICAL LOADS

DO NOT connect 240 Volt loads to 120 Volt receptacles. DO NOT

connect 3-phase loads to the generator. DO NOT connect 50 Hz

loads to the generator.

• Let engine stabilize and warm up for a few minutes after starting.

• Plug in and turn on the desired 120 or 240 Volt AC, single phase, 60

Hz electrical loads.

• Add up the rated watts (or amps) of all loads to be connected at

one time. This total should not be greater than (a) the rated wattage/

amperage capacity of the generator or (b) circuit breaker rating of the

receptacle supplying the power. See "Don't Overload the Generator".

2.4 DON’T OVERLOAD THE GENERATOR

Overloading a generator in excess of its rated wattage capacity

can result in damage to the generator and to connected electrical

devices. Observe the following to prevent overloading the unit:

• Add up the total wattage of all electrical devices to be connected

at one time. This total should NOT be greater than the

generator's wattage capacity.

• The rated wattage of lights can be taken from light bulbs. The

rated wattage of tools, appliances and motors can usually be

found on a data label or decal affixed to the device.

• If the appliance, tool or motor does not give wattage, multiply

volts times ampere rating to determine watts (volts x amps =

watts).

• Some electric motors, such as induction types, require about

three times more watts of power for starting than for running.

This surge of power lasts only a few seconds when starting

such motors. Make sure to allow for high starting wattage when

selecting electrical devices to connect to the generator:

1. Figure the watts needed to start the largest motor.

2. Add to that figure the running watts of all other connected

loads.

The Wattage Reference Guide is provided to assist in determining how

many items the generator can operate at one time.

NOTICE:

All figures are approximate. See data label on appliance for

wattage requirements.

2.5 WATTAGE REFERENCE GUIDE

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Running Watts

*Air Conditioner (12,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 1700

*Air Conditioner (24,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 3800

*Air Conditioner (40,000 Btu). . . . . . . . . . . . . . . . . . . . . . . . . . 6000

Battery Charger (20 Amp). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Belt Sander (3") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000

Chain Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Circular Saw (6-1/2") . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1000

*Clothes Dryer (Electric) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5750

*Clothes Dryer (Gas) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Clothes Washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1150

Coffee Maker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1750

*Compressor (1 HP). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Compressor (3/4 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1800

*Compressor (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1400

Curling Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

*Dehumidifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 650

Disc Sander (9") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Edge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Electric Blanket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400

Electric Nail Gun . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Electric Range (per element). . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

Electric Skillet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1250

*Freezer . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..700

*Furnace Fan (3/5 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 875

*Garage Door Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . .500 to 750

Hair Dryer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Operation

Hand Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .250 to 1100

Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 450

Impact Wrench . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

Iron. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

*Jet Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800

Lawn Mower. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1200

Light Bulb. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

Microwave Oven. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .700 to 1000

*Milk Cooler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1100

Oil Burner on Furnace . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300

Oil Fired Space Heater (140,000 Btu) . . . . . . . . . . . . . . . . . . . . . 400

Oil Fired Space Heater (85,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 225

Oil Fired Space Heater (30,000 Btu) . . . . . . . . . . . . . . . . . . . . . . 150

*Paint Sprayer, Airless (1/3 HP) . . . . . . . . . . . . . . . . . . . . . . . . . 600

Paint Sprayer, Airless (handheld). . . . . . . . . . . . . . . . . . . . . . . . . 150

Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 to 200

*Refrigerator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 700

Slow Cooker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200

*Submersible Pump (1-1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . 2800

*Submersible Pump (1 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . . 2000

*Submersible Pump (1/2 HP) . . . . . . . . . . . . . . . . . . . . . . . . . . 1500

*Sump Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .800 to 1050

*Table Saw (10") . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1750 to 2000

Television . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .200 to 500

Toaster . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000 to 1650

Weed Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500

* Allow 3 times the listed watts for starting these devices.

2.6 BEFORE STARTING THE GENERATOR

Prior to operating the generator, engine oil and gasoline will need

to be added, as follows:

2.6.1 ADDING ENGINE OIL

All oil should meet minimum American Petroleum Institute (API)

Service Class SJ, SL or better. Use no special additives. Select

the oil's viscosity grade according to the expected operating

temperature (also see chart).

• Above 40° F, use SAE 30

• Below 40° F and down to 10° F, use 10W-30

• All temperatures, use synthetic 5W-30

SAE 30

10W-30

10W -30

Synthetic 5W-30

Syn t het i c 5 W -30



Any attempt to crank or start the engine

before it has been properly serviced with the

recommended oil may result in an engine

failure.

1. Place generator on a level surface (not to exceed 15° in any

direction).

2. Clean area around oil fill and remove oil fill cap and dipstick.

3. Wipe dipstick clean.

4. Slowly fill engine with oil through the oil fill opening until it

reaches the high mark on the dipstick (Figure 9). Stop filling

occasionally to check oil level. Be careful not to over fill.

5. Install oil fill cap and finger tighten securely.

6. Check engine oil level before starting each time thereafter.

Figure 9 - Dipstick

HIGH

LOW

2.6.2 ADDING GASOLINE





Gasoline is highly FLAMMABLE and its

vapors are EXPLOSIVE. Never fill fuel tank

indoors. Never fill fuel tank when engine

is running or hot. Allow engine to cool

entirely before filling fuel tank. Avoid spilling

gasoline on HOT engine. DO NOT light a

cigarette or smoke when filling the fuel tank.



Do not overfill the fuel tank. Always leave

room for fuel expansion. If the fuel tank is

overfilled, fuel can overflow onto a HOT

engine and cause FIRE or EXPLOSION.

1. Use regular UNLEADED gasoline with the generator engine. Do

not use any gasoline with more than 10% added Ethanol, and

never use E85 gasoline. Do not mix oil with gasoline.

2. Clean area around fuel fill cap, remove cap.

3. Slowly add unleaded regular gasoline to fuel tank. Be careful

not to overfill (Figure 10).

4. Install fuel cap and wipe up any spilled gasoline.

Operation

Figure 10 - Fuel Tank

DO NOT Fill Above Lip

Fuel

Fuel Tank

IMPORTANT: It is important to prevent gum deposits from forming

in fuel system parts such as the carburetor, fuel hose or tank

during storage. Alcohol-blended fuels (called gasohol, ethanol

or methanol) can attract moisture, which leads to separation and

formation of acids during storage. Acidic gas can damage the fuel

system of an engine while in storage. To avoid engine problems,

the fuel system should be emptied before storage of 30 days or

longer. See the "Storage" section. Never use engine or carburetor

cleaner products in the fuel tank as permanent damage may

occur.

2.7 TO START THE ENGINE



Never start or stop engine with electrical

devices plugged into the receptacles AND

devices turned on.

1. Unplug all electrical loads from the unit's receptacles before

starting the engine.

2. Make sure the unit is in a level position (not to exceed 15° in

any direction).

3. OPEN the Fuel Shut-off Valve (Figure 11).

4. Turn engine ON/OFF switch to ON position (Figure 11).

Figure 11 - Engine Controls

5. Move engine CHOKE lever to the FULL CHOKE position (Figure

11).

6. To start engine, firmly grasp the recoil handle and pull slowly

until increased resistance is felt. Pull rapidly up and away.

7. When engine starts, move choke lever to 1/2-CHOKE position

until engine runs smoothly and then fully into RUN position.

If engine falters, move choke back out to 1/2-CHOKE position

until engine runs smoothly and then to RUN position.

NOTICE:

If engine fires, but does not continue to run, move choke lever to

the START position and repeat starting instructions.

2.8 STOPPING THE ENGINE

1. Shut off all loads, then unplug the electrical loads from

generator panel receptacles. Never start or stop the engine

with electrical devices plugged in and turned on.

2. Let engine run at no-load for several minutes to stabilize the

internal temperatures of engine and generator.

3. Move ON/OFF switch to OFF position.

4. Close fuel valve.

2.9 LOW OIL LEVEL SHUTDOWN SYSTEM

The engine is equipped with a low oil level sensor that shuts down

the engine automatically when the oil level drops below a specified

level. If the engine shuts down by itself and the fuel tank has

enough gasoline, check engine oil level.

2.9.1 SENSING LOW OIL LEVEL

If the system senses a low oil level during operation, the engine

shuts down. The engine will not run until the oil has been refilled

to the proper level.

3.1 MAINTENANCE SCHEDULE

Follow the calendar intervals. More frequent service is required

when operating in adverse conditions noted below.

Check Oil Level At Each Use

Change Oil ¥ *Every 50 Hours

Check Valve Clearance ***Every Season

Service Air Filter **Every 25 Hours

Replace Spark Plug ****Every 100 Hours

¥ Change oil after first 20 hours of operation.

* Change oil every month when operating under heavy load or in high

temperatures.

** Clean more often under dirty or dusty operating conditions. Replace air filter

parts if they cannot be adequately cleaned.

*** Check valve clearance and adjust if necessary after first 50 hours of

operation and every 100 hours thereafter.

**** Clean and re-gap spark plug every 50 hours.

Maintenance

3.2 PRODUCT SPECIFICATIONS

3.2.1 GENERATOR SPECIFICATIONS

Rated. Power .............................................................3.25 kW**

Surge Power ..................................................................3.75 kW

Rated AC Voltage ...........................................................120/240

Rated Current ....................................................27/13.5 Amps**

Rated Frequency ......................................... 60 Hz @ 3600 RPM

Phase .....................................................................Single Phase

Assembled Dimensions (L x W x H) ...622mm (24.5 in) x 564mm

(22.2 in) x 534mm (21.0 in)

Unit Weight ..........................................................50kg (110 lbs)

** Maximum wattage is subject to, and limited by, such factors as fuel Btu

content, ambient temperature, altitude, engine condition, etc.. Maximum

power decreases about 3.5% for each 1,000 feet above sea level; and will

also decrease about 1% for each 6° C (10° F) above 16° C (60° F) ambient

temperature.

3.2.2 ENGINE SPECIFICATIONS

Displacement ................................................................... 208 cc

Spark Plug Type ............F6TC, NGK BP6IS or Champion RN11YC

Spark Plug Gap .................................... 0.030 inch or (0.76 mm)

Gasoline Capacity ...............................12.7 L (3.35 U.S. gallons)

Oil Type....... See Chart in "Before Starting the Generator" Section

Oil Capacity ....................................................0.6 L (0.634 Qts.)

Run Time ................................................10.2 Hours at 1/2 Load

Class II Emission Certified*

* The engine manufacturer must warrant the emission control system

for a period of two years. This warranty coverage is in addition to

the warranty provided by Generac, and may cover the engine even if

Generac’s warranty does not.

3.3 GENERAL RECOMMENDATIONS

The warranty of the generator does not cover items that have been

subjected to operator abuse or negligence. To receive full value

from the warranty, the operator must maintain the generator as

instructed in this manual.

Some adjustments will need to be made periodically to properly

maintain the generator.

All adjustments in the Maintenance section of this manual should

be made at least once each season. Follow the requirements in the

"Maintenance Schedule".

NOTICE:

Once a year replace the spark plug and replace the air filter.

A new spark plug and clean air filter assure proper fuel-air

mixture and help the engine run better and last longer.

3.3.1 GENERATOR MAINTENANCE

Generator maintenance consists of keeping the unit clean and dry.

Operate and store the unit in a clean dry environment where it will

not be exposed to excessive dust, dirt, moisture or any corrosive

vapors. Cooling air slots in the generator must not become

clogged with snow, leaves, or any other foreign material.

Check the cleanliness of the generator frequently and clean when

dust, dirt, oil, moisture or other foreign substances are visible on

its exterior surface.



Never insert any object or tool through the

air cooling slots, even if the engine is not

running.

NOTICE:

DO NOT use a garden hose to clean generator. Water can enter

the engine fuel system and cause problems. In addition, if water

enters the generator through cooling air slots, some water will

be retained in voids and crevices of the rotor and stator winding

insulation. Water and dirt buildup on the generator internal

windings will eventually decrease the insulation resistance of

these windings.

3.3.2 TO CLEAN THE GENERATOR

• Use a damp cloth to wipe exterior surfaces clean.

• A soft, bristle brush may be used to loosen caked on dirt, oil,

etc.

• A vacuum cleaner may be used to pick up loose dirt and debris.

• Low pressure air (not to exceed 25 psi) may be used to

blow away dirt. Inspect cooling air slots and openings

on the generator. These openings must be kept clean and

unobstructed.

3.3.3 ENGINE MAINTENANCE



When working on the generator, always

disconnect the spark plug wire from spark

plug and keep wire away from spark plug.

3.3.4 CHECKING OIL LEVEL

See the “Before Starting the Generator” section for information on

checking the oil level. The oil level should be checked before each

use, or at least every eight hours of operation. Keep the oil level

maintained (Figure 9).

3.3.5 CHANGING THE OIL

Change the oil after the first 20 hours of operation, then every 50

hours thereafter. If running this unit under dirty or dusty conditions,

or in extremely hot weather, change the oil more often.

Maintenance



Hot oil may cause burns. Allow engine to

cool before draining oil. Avoid prolonged

or repeated skin exposure with used oil.

Thoroughly wash exposed areas with soap.

Use the following instructions to change the oil while the engine

is still warm:

1. Clean area around oil drain plug (Figure 12).

2. Remove oil drain plug from engine and oil fill plug to drain oil

completely into a suitable container.

3. When oil has completely drained, install oil drain plug and

tighten securely.

4. Fill engine with recommended oil. (See “Before Starting the

Generator” for oil recommendations.)

5. Wipe up any spilled oil.

6. Dispose of used oil at a proper collection center.

Figure 12 - Oil Drain, Check & Fill

3.3.6 REPLACING THE SPARK PLUG

Use spark plug F6TC, NGK BP6IS or Champion RN11YC. Replace

the plug once each year. This will help the engine start easier and

run better.

1. Stop the engine and pull the spark plug wire off of the spark

plug.

2. Clean the area around the spark plug and remove it from the

cylinder head.

3. Set the spark plug's gap to 0.76 mm (0.030 in.). Install the

correctly gapped spark plug into the cylinder head and torque

to 15 ft/lbs. (Figure 13).

Figure 13 - Spark Plug Gap

3.3.7 SPARK ARRESTOR

The engine exhaust muffler has a spark arrestor screen. Inspect

and clean the screen at least once each year (Figure 14). If unit is

used regularly, inspect and clean more often.

NOTICE:

If using the generator on any forest-covered, brush-covered

or grass-covered unimproved land, it must equipped with a

spark arrestor. The spark arrestor must be maintained in good

condition by the owner/operator.

Clean and inspect the spark arrestor as follows:

1. Remove clamp and spark arrestor from muffler.

2. Inspect screen and replace if torn, perforated or otherwise

damaged. DO NOT USE a defective screen. If screen is not

damaged, clean it with commercial solvent.

3. Replace the spark arrestor and clamp.

Figure 14 - Spark Arrestor

Muffler

Screen

Clamp

3.4 SERVICE AIR FILTER

The engine will not run properly and may be damaged if using a

dirty air filter. Clean the air filter every 25 hours (Figure 15). Clean

or replace more often if operating under dusty conditions (Part No.

0H33750219.

1. Remove air filter cover.

2. Wash in soapy water. Squeeze filter dry in clean cloth (DO

NOT TWIST).

3. Clean air filter cover before re-installing it.

Maintenance

Figure 15 - Air Filter

AIR FILTER

COVER

AIR

FILTER

UNLOCK

COVER

MOVE TO

THE RIGHT

3.5 VALVE CLEARANCE

• Intake — 0.10 ± 0.02mm (cold), (0.004" ± 0.0008" inches)

• Exhaust — 0.15 ± 0.02mm (cold) (0.006" ± 0.0008" inches)

After the first 50 hours of operation, check the valve clearance

in the engine and adjust if necessary.

Important: If feeling uncomfortable about doing this procedure or

the proper tools are not available, please take the generator to the

nearest service center to have the valve clearance adjusted. This is

a very important step to ensure longest life for the engine.

3.6 GENERAL

The generator should be started at least once every 30 days and

be allowed to run at least 30 minutes. If this cannot be done and

the unit must be stored for more than 30 days, use the following

information as a guide to prepare it for storage.





NEVER store engine with fuel in tank indoors

or in enclosed, poorly ventilated areas where

fumes may reach an open flame, spark or

pilot light as on a furnace, water heater,

clothes dryer or other gas appliance.

3.7 LONG TERM STORAGE

It is important to prevent gum deposits from forming in essential

fuel system parts such as the carburetor, fuel hose or tank during

storage. Also, experience indicates that alcohol-blended fuels

(called gasohol, ethanol or methanol) can attract moisture, which

leads to separation and formation of acids during storage. Acidic

gas can damage the fuel system of an engine while in storage.

To avoid engine problems, the fuel system should be emptied

before storage of 30 days or longer, as follows:

1. Add a quality gasoline stabilizer to the fuel per the

manufacturer's specifications, and run the unit for 10-15

minutes.

2. After engine cools down, remove all gasoline from the fuel

tank. Use a commercially available, non-conductive vacuum

siphon.





Drain fuel into approved container outdoors,

away from open flame. Be sure engine is

cool. Do not smoke.

3. Start and run engine until engine stops from lack of fuel.

4. After engine cools down, drain oil from engine. Refill with

recommended grade.

5. Remove spark plug and pour about 1/2 ounce (15 ml) of

engine oil into the cylinder. Cover spark plug hole with rag.

Pull the recoil starter a couple times to lubricate the piston

rings and cylinder bore. A fogging agent can also be used in

the place of oil.



Avoid spray from spark plug hole when

cranking engine.

6. Install and tighten spark plug. Do not connect spark plug wire.

7. Clean the generator outer surfaces. Check that cooling air

slots and openings on generator are open and unobstructed.

8. Store the unit in a clean, dry place.

3.8 OTHER STORAGE TIPS

• Do not store gasoline from one season to another.

• Replace the gasoline can if it starts to rust. Rust and/or dirt in

the gasoline will cause problems with the carburetor and fuel

system.

• If possible, store the unit indoors and cover it to give protection

from dust and dirt. BE SURE TO EMPTY THE FUEL TANK.

• If it is not practical to empty the fuel tank and the unit is to

be stored for some time, use a commercially available fuel

stabilizer added to the gasoline to increase the life of the

gasoline.

• Cover the unit with a suitable protective cover that does not

retain moisture.



NEVER cover the generator while engine and

exhaust area are warm.

4.1 TROUBLESHOOTING GUIDE

PROBLEM CAUSE CORRECTION

Engine is running, but no AC output

is available.

1. Circuit breaker is open.

2. Poor connection or defective cord set.

3. Connected device is bad.

4. Fault in generator.

1. Reset circuit breaker.

2. Check and repair.

3. Connect another device that is in good condition.

4. Contact Authorized Service Facility.

Engine runs good but bogs down

when loads are connected.

1. Short circuit in a connected load.

2. Generator is overloaded.

3. Engine speed is too slow.

4. Shorted generator circuit.

1. Disconnect shorted electrical load.

2. See “Don’t Overload the Generator” .

3. Contact Authorized Service Facility.

4. Contact Authorized Service Facility.

Engine will not start; or starts and

runs rough.

1. Dirty air filter.

2. Out of gasoline.

3. Stale gasoline.

4. Spark plug wire not connected to spark plug.

5. Bad spark plug.

6. Water in gasoline.

7. Over-choking.

8. Low oil level.

9. Excessive rich fuel mixture.

10. Intake valve stuck open or closed.

11. Engine has lost compression.

1. Clean or replace air filter.

2. Fill fuel tank.

3. Drain fuel tank and fill with fresh fuel.

4. Connect wire to spark plug.

5. Replace spark plug.

6. Drain fuel tank; fill with fresh fuel.

7. Put choke knob to No Choke position.

8. Fill crankcase to proper level.

9. Contact Authorized Service Facility.

10. Contact Authorized Service Facility.

11. Contact Authorized Service Facility.

Engine shuts down during

operation.

1. Out of gasoline.

2. Low oil level.

3. Fault in engine.

1. Fill fuel tank.

2. Fill crankcase to proper level.

3. Contact Authorized Service Facility.

Engine lacks power. 1. Load is too high.

2. Dirty air filter.

3. Engine needs to be serviced.

1. See “Don’t Overload the Generator”.

2. Replace air filter.

3. Contact Authorized Service Facility.

Engine “hunts” or falters. 1. Choke is opened too soon.

2. Carburetor is running too rich or too lean.

1. Move choke to halfway position until engine runs

smoothly.

2. Contact Authorized Service Facility.

Troubleshooting

Warranty

CALIFORNIA AND U.S. EPA EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The California Air Resource Board (CARB) and the United States Environmental Protection Agency (EPA), together with Generac Power Systems, Inc.

(Generac) are pleased to explain the Emission Control System Warranty (ECS Warranty) on your new 2012 equipment. New equipment that use small spark-

ignited engines must be designed, built, and equipped to meet stringent anti-smog standards for the state of California and the federal government. Generac

will warrant the emission control system on your equipment for the period of time listed below provided there has been no abuse, neglect, unapproved

modification or improper maintenance of your equipment.

The emission control system on this equipment includes all components whose failure would increase the emissions of any regulated pollutant. These

components are listed in the Emissions Information section of this manual.

MANUFACTURER’S WARRANTY COVERAGE:

This ECS Warranty is valid for two years, or for the same period as specified in the Generac Limited Warranty, whichever is longer. For equipment with hour

meters, the warranty period is a number of hours equal to half the Useful Life to which the equipment is certified, or the warranty period specified above in

years, whichever is less. The Useful Life can be found on the Emission Control Label on the engine. If, during such warranty period, any emission-related

part on your equipment is found to be defective in materials or workmanship, repairs or replacement will be performed by a Generac Authorized Warranty

Service Dealer.

OWNER'S WARRANTY RESPONSIBILITIES:

As the equipment owner, you are responsible for the completion of all required maintenance as listed in your factory supplied Owner's Manual. For warranty

purposes, Generac recommends that you retain all receipts covering maintenance on your generator, but Generac cannot deny warranty solely due to the

lack of receipts.

You should be aware that Generac may deny any and/or all warranty coverage or responsibility if your equipment, or a part/component thereof, has failed

due to abuse, neglect, improper maintenance, or unapproved modifications.

You are responsible for contacting a Generac Authorized Warranty Dealer as soon as a problem occurs. The warranty repairs should be completed

in a reasonable amount of time, not to exceed 30 days.

Warranty service can be arranged by contacting either your selling dealer or a Generac Authorized Warranty Service Dealer. To locate the Generac Authorized

Warranty Service Dealer nearest you, call our toll free number below, or email [email protected].

1-800-333-1322

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Control System Warranty, which is provided to you

by Generac pursuant to federal law. See also the "Generac Limited Warranties for Generac Power Systems, Inc.," which is enclosed herewith on a separate

sheet, also provided to you by Generac. Note that this warranty shall not apply to any incidental, consequential or indirect damages caused by defects in

materials or workmanship or any delay in repair or replacement of the defective part(s). This warranty is in place of all other warranties, expressed or implied.

Specifically, Generac makes no other warranties as to the merchantability or fitness for a particular purpose. Any implied warranties allowed by law shall

be limited in duration to the terms of the express warranty provided herein. Some states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

The ECS Warranty applies only to the emission control system of your new equipment. Both the ECS Warranty and the Generac Warranty describe important

rights and obligations with respect to your new engine.

Warranty service can be performed only by a Generac Authorized Warranty Service Facility. When requesting warranty service, evidence must be presented

showing the date of the sale to the original purchaser/owner.

If you have any questions regarding your warranty rights and responsibilities, you should contact Generac at the following address:

ATTENTION WARRANTY DEPARTMENT

GENERAC POWER SYSTEMS, INC.

P.O. BOX 297 • WHITEWATER, WI 53190

Part 1 of 2

Part No. 0J8147B Rev. A 01/12

Warranty

EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS Warranty) for equipment using small spark-ignited engines:

(a) Applicability: This warranty shall apply to equipment that uses small off-road engines. The ECS Warranty period shall begin on the date the new

equipment is purchased by/delivered to its original, end-use purchaser/owner and shall continue for the lesser of:

(1) The period of time specified in the Generac Limited Warranty enclosed herewith, but not less than 24 months, or

(2) For engines equipped with hour meters, a number of operating hours equal to half of the engine’s useful life. The useful life is specified on the

Emissions Control Label on the engine.

(b) General Emissions Warranty Coverage: Generac warrants to the original, end-use purchaser/owner of the new engine or equipment and to each

subsequent purchaser/owner that the ECS when installed was:

(1) Designed, built and equipped so as to conform with all applicable regulations; and

(2) Free from defects in materials and workmanship which cause the failure of a warranted part at any time during the ECS Warranty Period.

(1) Any warranted part that is not scheduled for replacement as required maintenance in the Owner's Manual shall be warranted for the ECS

Warranty Period. If any such part fails during the ECS Warranty Period, it shall be repaired or replaced by Generac according to Subsection (4)

below. Any such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.

(2) Any warranted part that is scheduled only for regular inspection as specified in the Owner's Manual shall be warranted for the ECS Warranty

Period. A statement in the Owner’s Manual to the effect of "repair or replace as necessary" shall not reduce the ECS Warranty Period. Any

such part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty Period.

(3) Any warranted part that is scheduled for replacement as required maintenance in the Owner's Manual shall be warranted for the period of time

prior to first scheduled replacement point for that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or

replaced by Generac according to Subsection (4) below. Any such emissions-related part repaired or replaced under the ECS warranty shall be

warranted for the remainder of the period prior to the first scheduled replacement point for that part.

(4) Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be performed at no charge to the owner at a

Generac Authorized Warranty Service Facility.

(5) Notwithstanding the provisions of subsection (4) above, warranty services or repairs must be provided at Generac Authorized Service

Facilities.

(6) When the engine is inspected by a Generac Authorized Warranty Service Facility, the purchaser/owner shall not be held responsible for

diagnostic costs if the repair is deemed warrantable.

(7) Throughout the ECS Warranty Period, Generac shall maintain a supply of warranted emission-related parts sufficient to meet the expected

demand for such parts.

(8) Any Generac authorized and approved emission-related replacement parts may be used in the performance of any ECS Warranty maintenance

or repairs and will be provided without charge to the purchaser/owner. Such use shall not reduce Generac ECS Warranty obligations.

(9) No modifications, other than those explicitly approved by Generac, may be made to the generator. Unapproved modifications void this ECS

Warranty and shall be sufficient ground for disallowing an ECS Warranty claim.

(10) Generac shall not be held liable hereunder for failures of any non-authorized replacement parts, or failures of any authorized parts caused by

the use of non-authorized replacement parts.

EMISSION RELATED PARTS MAY INCLUDE THE FOLLOWING (IF EQUIPPED):

1) FUEL METERING SYSTEM

A. CARBURETOR AND INTERNAL PARTS

B. FUEL TANK / CAP

C. FUEL LINES

D. EVAPORATIVE VENT LINES

E. REGULATOR (GASEOUS FUELS)

F. CARBON CANISTER

2) AIR INDUCTION SYSTEM

A. INTAKE MANIFOLD

B. AIR FILTER

3) IGNITION SYSTEM

A. SPARK PLUGS

B. IGNITION COILS / MODULE

4) AIR INJECTION SYSTEM

A. PULSE AIR VALVE

5) EXHAUST SYSTEM

A. CATALYST

B. EXHAUST MANIFOLD

Part 2 of 2

Part No. 0J8147B Rev. A 01/12

Manual Part No. 0J8901 Rev D (05/21/13) Printed in China

Warranty

GENERAC POWER SYSTEMS “TWO YEAR” LIMITED WARRANTY FOR

3250 and 5000 WATT CENTURION PORTABLE GENERATORS

For a period of two years from the date of original sale, Generac Power Systems, Inc. (Generac) warrants its Centurion generators will be free from defects in

materials and workmanship for the items and period set forth below. Generac will, at its discretion, repair or replace any part that, upon examination, inspection

and testing by Generac or a Generac Authorized Warranty Service Dealer, is found to be defective. Any equipment that the purchaser/owner claims to be defective

must be returned to and examined by the nearest Generac Authorized Warranty Service Dealer. All transportation costs under the warranty, including return to the

factory, are to be borne and prepaid by the purchaser/owner. This warranty applies only to Generac Centurion portable generators and is not transferable from

original purchaser.

WARRANTY SCHEDULE

Consumer applications are warranted for two (2) years. Commercial applications are warranted for 1 (one) year. Rental applications are warranted for 90 (ninety) days.

**This Warranty applies to units used in the US and Canada. Contact the Warranty Department for information on units used in International Markets.**

CONSUMER APPLICATION

YEARS ONE AND TWO - Limited comprehensive coverage on Labor and Part(s) listed (proof of purchase and maintenance is required):

• All Components

COMMERCIAL APPLICATION

YEAR ONE – Limited comprehensive coverage on Labor and Part(s) listed (proof of purchase and maintenance is required):

• All Components

RENTAL APPLICATION

90 DAYS - Limited comprehensive coverage on Labor and Part(s) listed (proof of purchase and maintenance is required).

• All Components

NOTE: For the purpose of this warranty “consumer use” means personal residential household or recreational use by original purchaser. This warranty does not apply

to units used for Prime Power in place of utility where utility power service is present or where utility power service does not normally exist. Once a generator

has experienced commercial or rental use, it shall thereafter be considered a non-consumer use generator for the purpose of this warranty.

All warranty expense allowances are subject to the conditions defined in the Generac Service Policy Manual.

THIS WARRANTY SHALL NOT APPLY TO THE FOLLOWING:

• Generac Centurion portable generators built prior to June 2010.

• Damage to any covered components or consequential damages caused by the use of a non-OEM part will not be covered by the warranty.

• Costs of normal maintenance and adjustments.

• Failures caused by any contaminated fuels, oils or lack of proper oil levels.

• Repairs or diagnostics performed by individuals other than Generac authorized dealers not authorized in writing by Generac Power Systems.

• Failures due, but not limited, to normal wear and tear, accident, misuse, abuse, negligence or improper use. As with all mechanical devices, the Generac engines need

periodic part(s) service and replacement to perform as designed. This warranty will not cover repair when normal use has exhausted the life of a part(s) or engine.

• Failures caused by any external cause or act of God including, without limitation, collision, theft, vandalism, riot or wars, nuclear event, fire, lightning, earthquake,

windstorm, hail, volcanic eruption, water or flood, tornado or hurricane.

• Damage related to rodent and/or insect infestation.

• Products that are modified or altered in a manner not authorized by Generac in writing.

• Any incidental, consequential or indirect damages caused by defects in materials or workmanship, or any delay in repair or replacement of the defective part(s).

• Failure due to misapplication.

• Telephone, cellular phone, facsimile, internet access or other communication expenses.

• Expenses related to “customer instruction” or troubleshooting where no manufacturing defect is found.

• Rental equipment used while warranty repairs are being performed.

• Overnight freight or special shipping costs for replacement part(s).

• Overtime, holiday or emergency labor.

• Starting batteries, fuses, light bulbs and engine fluids.

THIS WARRANTY IS IN PLACE OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED. SPECIFICALLY, GENERAC MAKES NO OTHER WARRANTIES AS TO THE

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Any implied warranties allowed by law shall be limited in duration to the terms of the express warranty

provided herein. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. GENERAC’S ONLY LIABILITY

SHALL BE THE REPAIR OR REPLACEMENT OF PART(S) AS STATED ABOVE. IN NO EVENT SHALL GENERAC BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES, EVEN IF SUCH DAMAGES ARE A DIRECT RESULT OF GENERAC’S NEGLIGENCE. Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above limitation may not apply to you. This warranty gives you specific legal rights. You also have other rights from state to state.

GENERAC POWER SYSTEMS, INC. • P.O. BOX 8 • Waukesha, WI 53187

Ph: (888) GENERAC (436-3722) • Fax: (262) 544-4851

To locate the nearest Authorized Dealer visit our website www.generac.com

Part No. 0H8957 Revision E (05/13)

Manual del propietario

Generador portátil

MODELO 006104-1

SOPORTE DE CONCESIONARIO

AUTORIZADO:

2 AÑOS

GARANTÍA

LIMITADA

PELIGRO



¡HUMOS DE ESCAPE MORTALES! ¡Utilícelo

SOLAMENTE al AIRE LIBRE y lejos de ventanas,

puertas y respiraderos!



NO DISEÑADO PARA SER USADO EN

APLICACIONES DE SOPORTE DE VIDA CRÍTICA.



GUARDE este Manual. Proporcione este manual a

cualquier operador del generador.

Introducción .......................................................... 19

Lea este manual completamente .......................... 19

Reglas de seguridad ............................................. 19

Índice de estándares ....................................................21

Información general.............................................. 22

1.1 Desempaque ................................................................22

1.1.1 Caja de accesorios ..........................................22

1.2 Montaje .......................................................................22

1.2.1 Montaje del juego de accesorios ......................22

1.3 Información de emisiones ............................................22

Operación ............................................................. 23

2.1 Conozca el generador ...................................................23

2.2 Juego de cables y conectores ......................................24

2.2.1 Receptáculo dúplex de 120 VAC ......................24

2.2.2 Receptáculo de giro de 120/240 VAC, 20A ......24

2.3 Cómo usar este generador ...........................................24

2.3.1 Conexión a tierra del generador cuando

se usa como unidad portátil.............................25

2.3.2 Conexióndel generador al sistema eléctrico

de un edificio ...................................................25

2.3.3 Conexión de las cargas eléctricas ....................25

2.4 No sobrecargue el generador........................................25

2.5 Guía de referencia de potencias ....................................25

2.6 Antes de poner en marcha el generador .......................26

2.6.1 Agregar aceite de motor ...................................26

2.6.2 Añadir gasolina ................................................26

2.7 Arranque del motor ......................................................27

2.8 Detener el Motor ..........................................................27

2.9 Sistema de apagado - nivel de aceite ...........................27

2.9.1 Sensando el bajo nivel de aceite ......................27

Mantenimiento ...................................................... 27

3.1 Programa de mantenimiento .........................................27

3.2 Especificaciones del producto ......................................28

3.2.1 Especificaciones del generador ........................28

3.2.2 Especificaciones del motor ..............................28

3.3 Recomendaciones generales ........................................28

3.3.1 Mantenimiento del generador ...........................28

3.3.2 Para limpiar el generador .................................28

3.3.3 Mantenimiento del motor .................................28

3.3.4 Revisar el nivel de aceite ..................................28

3.3.5 Cambio de aceite .............................................28

3.3.6 Reemplazo de la bujía ......................................29

3.3.7 Supresor de chispa ..........................................29

3.4 Servicio al filtro de aire .................................................29

3.5 Claridad de la valvula ...................................................30

3.6 General ........................................................................30

3.7 Almacenamiento por largo plazo ...................................30

3.8 Otros consejos para almacenamiento ...........................30

Detección de fallas ............................................... 31

5.1 Guía de localización y resolución de problemas ............31

Garantía ................................................................ 32

Índice

ADVERTENCIA!

Proposición 65 de California

El escape del motor y algunos de sus componentes son conocidos pore el Estado de California como

causa de cáncer, defectos congénitos y otros daños reproductivos.

ADVERTENCIA!

Proposición 65 de California

Este producto contiene o emite sustancias químicas que son conocidas por el Estado de California como

causa de cáncer, defectos congénitos y otros daños reproductivos.

La page charge ...

Generac Centurion 3250 G0061041 Manuel utilisateur

Marque: Generac

Modèle: Centurion 3250 G0061041

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Generac Centurion 3250 G0061041 User manual
español: Generac Centurion 3250 G0061041 Manual de usuario