Middle Atlantic Products Credenza Rack Assembly Instruction Manual

Marque: Middle Atlantic Products

Modèle: Credenza Rack

Taper: Assembly Instruction Manual

Ce manuel convient également à

C5 SERIES CREDENZA RACK

C5 SERIES

CREDENZA RACK

assembly instructions

Thank you for purchasing the C5 Series Credenza Rack. Please read all instructions thoroughly

before assembling this product.

I-00661 Rev E

- Built-in thermostatically controlled cooling.

- Heavy duty frame ships separate to allow for equipment integration before finished surfaces are

attached.

- 14 rackspaces per bay.

- Factory installed casters.

- Weight rating of 800 pounds, including finishing kit*, with maximum 350 pounds located on

top surface. (*Middle Atlantic Products supplied finishing kit is 200 pounds complete)

PRODUCT FEATURES

Page 2

WARNINGS

WEIGHT DISTRIBUTION/MONITOR SIZING

Monitor may be free standing for 1, 2 or 3 bay units.

When using free standing monitors, monitors must not

extend beyond the width of work surface:

1 Bay = 23.50 “ [596.9mm]

2 Bay = 45.88” [1165.35mm]

3 Bay = 68.25“ [1733.55mm]

For 2 Bay using optional monitor mount kit:

Largest single monitor size: 80” [2032mm] diagnal

225 LB [102.06 Kg] Max weight

For 3 Bay using optional monitor mount kit:

Largest single monitor size: 80” [2032mm] diagnal

225 lbs [102.06 Kg] Max weight

Largest dual monitors: 65” [1651mm] diagnal

320 lbs [145.15 Kg] Max Weight

All units (1,2 or 3 bay) have a total maximum

equipment weight capacity of 600 lbs [272.15 Kg]

with a top work surface maximum weight

capacity of 350 lbs [158.76 Kg]

WARNING - Risk of Collapse and Instability. This enclosure is intended for use only with the equipment and maximum weights indicated.

Use with other equipment or equipment heavier than the maximum weights indicated may result in instability causing possible injury.

AVERTISSEMENT - Risque d'effondrement et d'instabilité. Ce enceinte est prévu pour l'usage seulement avec l'équipement et

les poids maximum indiqués. L'utilisation avec l'autre équipement ou l'équipement plus lourd que les poids maximum indiqués peut avoir

comme conséquence l'instabilité causant la blessure possible.

WARNING - Death or serious injury may occur when children climb on audio and/or video equipment urniture. A remote control or

toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip over on to the child.

AVERTISSEMENT - La mort ou la blessure sérieuse peut se produire quand les enfants s'élèvent sur des meubles d'audio et/ou de

matériel vidéo. Un à télécommande ou les jouets placés sur la fourniture peut encourager un enfant à s'élever sur la fourniture et en

conséquence la fourniture peut incliner plus de dessus à l'enfant.

WARNING - Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment

may result in death or serious injury due to the furnishing collapsing or over turning onto a child.

AVERTISSEMENT - Replacer l'audio et/ou le matériel vidéo aux meubles pas spécifiquement conçus pour soutenir l'audio et/ou le

matériel vidéo peut avoir comme conséquence la mort ou la blessure sérieuse due à s'effondrer de fourniture ou au-dessus de la

rotation sur un enfant.

Page 3

FAN NOTES

A) TEMPERATURE PROBE: Temperature detection probe (A).

NOTE: Locate probe near hottest equipment.

NOTE: Blue LED in exhaust area illuminates when the unit is receiving power.

TURN ON TEMPERATURE: The blower will turn on at 87° F (30.5° C) and run proportionately.

Speed increases with temperature from 87° F (30.5° C) to 95° F (35° C). At 95° F (35° C) and above,

the blower will run at full speed. The blower will stop running at 85° F (29.4° C).

(A)

Use obrounds for cable tie points

Page 4

1) Place vent underneath the flange. (FIGURE A)

2) Using a #2 Phillips driver, install the 10-32 screws into the top of the vent (FIGURE A).

Use hardware kit #91-00507.

FIGURE A

VENT INSTALLATION

Page 5

NOTE: For accessories related to the Side Panels, please read those instructions thoroughly before

continuing with the installation below

1) Install side panels by placing the four pre-installed hooks into the four slots on the frame. (FIGURE B)

NOTE: When installing side panels, ensure door hinge plates are located at the front of the frame.

FIGURE B

SIDE PANEL INSTALLATION

Door Hinge Plate

Page 6

NOTE: For accessories related to the Top Surface, please read those instructions thoroughly before

continuing with the installation below

1) Align the top using wooden dowels in the side panels as a guide. Attach top surface to the frame

using provided wood screws (HW Kit #91-00517), extra screws provided. (FIGURE C)

NOTE: If installing a monitor mount, please read the instructions with the monitor mount prior to

installing.

Number of #10 x 5/8” Screws Used Per Credenza Top

3-Bay 12

2-Bay 8

1-Bay 4

Configuration Screws

1-Bay 91-00514

2-Bay 91-00515

3-Bay 91-00516

Configuration Hardware Kit

Sub-Hardware Kits

Qty (All models get one

91-00517)

FIGURE C

HARDWARE KIT QTY

TOP SURFACE INSTALLATION

91-00508/91-00518

Page 7

1) Install doors using provided wood screws (two places per door) as shown (HW Kit #91-00518).

(FIGURE D)

Factory Installed Bumpers

(NOTE:

(3) Three replacement bumpers supplied)

FIGURE D

DOOR INSTALLATION

Page 8

1) Door to be installed onto credenza frame using provided screws (two places per door) as shown

(HW Kit #91-00518). (FIGURE E)

FIGURE E

DOOR INSTALLATION ONTO MULLION

Page 9

Side Adjustment: Adjusts horizontal placement of door. Adjusts door-to-door gap.

Height Adjustment: Adjusts vertical height of door.

Depth Adjustment: Adjusts the space between the door and the face of the frame of credenza.

Directional adjustments apply to the door in the closed position. Hinge adjustment is done with door in

open position. Refer to (FIGURE G) for appropriate adjustments.

Door in open position

FIGURE G

FIGURE F

LOCK/KNOB INSTALLATION

HINGE ADJUSTMENTS

1) Install lock/knob into pre-drilled pilot holes. (FIGURE F)

Page 10

WARRANTY

Middle Atlantic Products, Inc. (the "Company") warrants the C5 Credenza Frame to be free from defects in material or workmanship under normal use and conditions for the lifetime

of the product, the Cladding for (7) seven years, and the Fans for (3) three years from the date of shipment by the Company.

The Company's entire liability to the purchaser, and the purchaser's (or any other party's) sole and exclusive remedy, under this warranty shall be limited, at the Company's option, to either (a) return of and

refund of the price paid for, or (b) repair or replacement at the Company's factory of the products purchased, or any part or parts thereof, which the Company has determined to be defective after inspection

thereof at the Company's factory.

This warranty does not cover damage due to acts of God, accident, misuse, abuse or negligence by parties other than the Company, or any modification or alteration of the products. In addition, this warranty

does not cover damage due to improper handling, assembly, installation or maintenance.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE COMPANY BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT, OR CONSEQUENTIAL DAMAGES

WHATSOEVER (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION OR ANY OTHER PECUNIARY LOSS) ARISING OUT OF THE USE

OF THE PRODUCTS PURCHASED, EVEN IF THE COMPANY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE COMPANY'S LIABILITY TO THE PURCHASER (OR ANY OTHER

PARTY) HEREUNDER, IF ANY, SHALL IN NO EVENT EXCEED THE PURCHASE PRICE OF THE PRODUCTS PAID TO THE COMPANY.