Summit GC443BGL Le manuel du propriétaire

BUILT-IN CERAMIC GAS COOKTOP

Model GC443BGL

Instruction Manual

04059ULSUMNAT (ENG) - 07.11.2016

Dear Customer,

Thank you for buying one of our ceramic gas cooktops. We are sure

that this modern, functional and practical appliance, made using the

finest quality materials, will fully satisfy your requirements.

This new appliance is very easy to use, but in order to obtain the best

results, we strongly recommend that you read this booklet carefully

before use. The manufacturer cannot be considered responsible for

any damages to people or things in the event of incorrect installation or

improper use of this appliance.

We reserve the right to make any changes to our products which we

consider to be necessary or useful, also in the interest of the user,

without affecting the essential characteristics in terms of functionality

and safety.

The staff of

Felix Storch, Inc.

Summit Appliance Division

An ISO 9001:2015 registrated company

770 Garrison Avenue

Bronx, New York 10474

www.summitappliance.com

1

TABLE OF CONTENTS

Important Safeguards .................................................................... 2

Location of Parts ............................................................................ 4

Installation ................................................................................. 5 - 8

Installing the Cooktop .............................................................. 5

Sealing the Cooktop ................................................................ 6

Room Ventilation ..................................................................... 6

Gas Connection ...................................................................... 7

Electrical Connection .......................................................... 7 - 8

Adjustments ................................................................................... 9

Conversions ................................................................................. 10

Using the Cooktop ................................................................ 11 - 12

Lighting the Burners .............................................................. 11

Proper Use of the Burners .............................................. 11 - 12

Cleaning ................................................................................. 13 - 14

Servicing ....................................................................................... 15

Replacing Components

Limited Warranty .......................................................................... 16

2

IMPORTANT SAFEGUARDS

For all appliances:

the installation of appliances designed for manufactured (mobile)

homes must conform with the Manufactured Home Construction and

Safety Standard, Title 24, CFR, Part 3280 (formerly the Federal

Standard for Mobile Home Construction and Safety, Title 24, HUD

(Part 280)), or when such standard is not applicable, the Standard for

Manufactured Home Installations, ANSI/NCSBCS 225.1, or with

applicable local codes.

Leak testing of the appliance shall be conducted according to the

manufacturer’s instructions.

Assure that gas connection conforms with local codes and ordinances. In

the absence of local codes, installations must conform with American

National Standard, National Fuel Gas Code ANSI Z223/NFPA 54 or

Canadian CAN/CGA_B 149.1 or CAN/CGA-149.2.

The product must be electrically grounded in accordance with local codes

or, in the absence of local codes, with the National Electrical Code, NFPA

70

or the Canadian Electric Code, CSA C22.1-02.

The appliance and its individual shutoff valve must be disconnected from

the gas supply piping system during any pressure testing of that system at

test pressure in excess of 1/2 psi (3.5 kPa). The maximum gas supply

pressure is 4 inch WC (water column) for natural gas and 11 inch WC for

LP. The gas

pressure regulator provided is regulated to 1 inch WC above

the manufacturer's

specified manifold pressure.

Always disconnect the electrical supply before servicing the appliance.

WARNING:

If the information in this manual is

not followed exactly, a fire or explosion could

result causing property damage, physical

injury or death.

Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

What to do if you smell gas:

 Do not try to turn on any appliance.

 Do not touch any electrical switch. Do not

use any phone in your building.

3

 Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

 If you cannot reach your gas supplier, call

the fire department.

Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

Save any nozzles removed from the appliance for future use.

The maximum depth of cabinets installed above the cooktop should be 13

inches (330 mm).

Keep the appliance clear and free from combustible materials, gasoline

and other flammable vapors and liquids.

Do not obstruct the flow of gas or block any air vents.

The appliance must be isolated from the gas supply piping system by

closing its individual manual shut-off valve during any pressure testing of

the gas supply piping system at test pressures equal to or less than 1/2 psi

(3.5 kPa).

SAVE THESE INSTRUCTIONS

4

LOCATION OF PARTS

Part No.

Description

Heat supplied

1

Ultra-rapid gas burner

11000-12000 Btu/h

3

Semi-rapid gas burner

6000 Btu/h

6

Enameled steel pan support for

ultra-rapid burner

7

Enameled steel pan support for

semi-rapid burners

8

Enameled steel pan support for

wok (only on ultra-rapid gas

burner)

10

Burner no. 1 control knob

12

Burner no. 3 control knob

NOTICE: This appliance has been manufactured for residential use only.

MODEL: GC443BGL

5

INSTALLATION

Installation, adjustment of controls and maintenance must only be

carried out by qualified personnel.

Incorrect installation may cause damage to persons, animals or property

for which the Manufacturer will not be considered responsible. During

the life of the system, the automatic safety or regulating devices on the

appliance may only be modified by the manufacturer or by his duly

authorized dealer.

Installing the Cooktop

Check that the appliance is in good condition after having removed the outer

packaging and internal wrappings from around the various loose parts. In

case of doubt, do not use the appliance and contact qualified personnel.

Never leave packaging materials (cardboard, bags, Styrofoam, nails,

etc.) within the reach of children since these items could become

sources of danger.

The measurements of the opening made in the top of the modular cabinet or

island and into which the cooktop will be installed are indicated in Fig. 1 and

the following chart. Always comply with the measurements given for the hole

into which the appliance will be recessed (see Figs. 1 and 2).

Use These Dimensions (in inches)

Model No.

A

B

C

D

E

GC443BGL

41-¾

13-5/8

3-1/8

5

3

30"

Min.

6"

Fig. 1

Fig. 2

6

Sealing the Cooktop

The cooktop has a special seal that prevents liquid from getting into the

cabinet below. Follow these instructions exactly in order to apply this seal

correctly:

Detach the seals from their backing, checking that the transparent protection

still adheres to the seal itself.

Turn the cooktop over and correctly position seal "E" (Fig. 3) under the edge

of the cooktop itself so that the outer side of the seal perfectly matches the

outer edge of the cooktop. The ends of the strips must fit together without

overlapping.

Once the seals are securely and evenly fixed to the cooktop, press them into

place with the fingers and remove the strip of protective paper from the seal.

Set the plate into the hole made in the cabinet.

FIG. 3

FIG. 4

Fix the hob with the proper brackets “S” and fit the prominent part into the

porthole “H” on the bottom; turn the screw “F” until the bracket “S” stick on the

top (fig. 4). In fastening the brackets, do not use a mechanical or electric

screwdriver. Instead, use a hand-operated screwdriver and exert only

moderate force.

The adjacent walls (left, right or behind) that exceed the cooktop in height

must be at a minimum distance from the cut hole as indicated in Fig. 1 and the

chart on the preceding page.

In order to avoid accidentally touching the hot cooktop bottom, it is necessary

to put a horizontal wooden insert, attached by screws, at a minimum distance

of 6" below the lower surface of the cooktop (see Fig. 1).

Room Ventilation

To ensure proper operation of the appliance, be sure that the room where it is

installed has adequate ventilation.

The appliance should not be installed with a ventilation system that

blows air downward toward the appliance. It may cause ignition and

combustion problems with the gas cooking appliance resulting in

personal injury or unintended operation.

7

Gas Connection

Natural Gas and Propane Gas

Natural gas installations require the connection of a gas regulator to the

cooktop. You will find this regulator among the accessories supplied with the

appliance.

Assemble the regulator (noting the direction of gas flow) and transition pieces

(supplied) in accordance with the figure below.

The maximum gas supply

pressure (in accordance with the

inlet pressure rating of the

pressure regulator supplied).

The gas supply pressure for

testing the regulator setting the

pressure shall be at least 1 in.

water column (249 Pa) above the

specified manifold pressure).

The transition piece on the supply side of the regulator must be provided by

the installer. Unions compatible with the hose fittings must be used and

connections tested for gas leaks.

Be sure that the supply connection point is accessible with the appliance

installed.

WARNING: Be sure the hose assembly is restrained from accidental contact

with the flue or flue outlet of an under-counter oven.

Electrical Connection

The electrical connections of the appliance must be carried out in compliance

with local standards and provisions.

Before connecting the appliance, check that:

1. The electrical capacity of the main electrical supply and current sockets suit

the maximum power rating of the appliance. (See the data label attached

to the bottom of the cooktop.)

2. The socket or system has an efficient ground connection in compliance

with local standards and provisions. The manufacturer is not responsible

for failure to comply with these provisions.

8

When the appliance is connected to electrical power by a socket:

Fit a standard plug suited to the load indicated on the data label to the

cable.

Fit the wires following Fig. 5, noting the following correspondences:

Letter L (live) = wire

Letter N (neutral) = wire

Ground symbol = green or yellow-green wire

Never use adapters or shunts for connection since these could create false

contacts and lead to dangerous overheating.

The outlet must be accessible after the cooktop is built in.

When the appliance is connected directly to the electrical main:

Install an omnipolar circuit-breaker between the appliance and the electrical

main. This circuit-breaker should be sized in compliance with local

installation regulations.

Remember that the ground wire must not be interrupted by the circuit-

breaker.

For optimum safety, the electrical connection may also be protected by a

high-sensitivity differential circuit-breaker.

You are strongly advised to fix the yellow-green ground wire to an efficient

grounding system

Fig. 5

9

ADJUSTMENTS

Always disconnect the appliance from the electrical power source

before making any adjustments. All seals must be replaced by the

technician when any adjustments are completed.

The burners do not require any regulation of incoming air.

Taps

"Reduced rate" adjustment:

1. Switch on the burner and turn the relative knob to the “Reduced rate”

position (small flame fig. 8 page 11).

2. Remove knob “M” (fig. 6 and 6/A) of the tap, which is simply pressed on to

its rod.

3. The by-pass for minimal rate regulation can be: beside the tap (fig. 6) or

inside the shaft. In any case, to access the regulation, it can be done

through the insertion of a small screwdriver ‘’D’’ beside the tap (fig. 6) or in

the hole ‘’C’’ inside the shaft of the tap (fig 6/A).

Turn the throttle screw to the right or left until the burner flame has been

adequately regulated to the “Reduced rate” position.

The flame should not be too low: the lowest small flame should be continuous

and steady. Re-assemble the several components.

It is understood that only burners operating with Natural Gas or City Gas

should be subjected to the above-mentioned adjustments. The screw

must be fully locked when the burners operate with Propane (turn

clockwise).

Fig. 6

FIG. 6/A

10

CONVERSIONS

Replacing Nozzles

The burners can be adapted to suit different

types of gas by fitting the nozzles that corres-

pond to the gas used. To do this, it is

necessary to remove the burner heads and

use a straight key "B" to unscrew the nozzle

"A" (see Fig. 7) and replace it with a nozzle

corresponding to the gas used.

Be sure the nozzle is seated tightly.

After making these replacements, the technician must regulate the

burners as described in Adjustments on the previous page and reset

any seals. He should affix the label corresponding to the new gas type

to replace the label previously applied. The nozzles and labels may be

included in a kit with the unit, or obtained from the dealer.

How to change the setting of the pressure regulator supplied with the

cooktop:

The gas regulator was set up to Natural Gas. To convert to LP Gas:

1. Unscrew the aluminum cap

2. Remove and turn the plastic pin 180°

3. Screw in the plastic pin

4. Screw in the aluminum cap

To make it easier for the fitter, we have prepared a table indicating the flow

capacities, the heat capacities of the burners, the diameter of the nozzles and

the working pressure for the various types of gas.

Burners

Gas

Normal

Manifold

Pressure,

inches water

column

Injector

Diameter,

1/100 mm

Nominal Heat

Input (Btu/h)

No.

Description

Min.

Max.

1

Ultra-Rapid

Propane HD-5

Natural Gas

11

4

94

170

5100

11000

12000

3

Semi-Rapid

Propane HD-5

Natural Gas

11

4

70

120

2400

6000

1

3

1

3

Arrangement

of Burners

Fig. 7

11

USING THE COOKTOP

Lighting the burners

A diagram is screened beside each knob on the control panel of your cooktop.

This diagram indicates to which burner the knob in question corresponds.

After having opened the gas main or bottled gas tap, light the burners as

described below:

The knobs of the burners are equipped with a safety cut-off device. They

must be turned in a counter-clockwise direction until they reach the full-on

position (large flame icon, Fig. 8) and come to a stop. Now push down on the

knob. The burner should ignite in 2 or 3 seconds. Keep the knob depressed

as you turn it toward the reduced rate position (small flame icon, Fig. 8) to

adjust the flame. Should the flame accidentally go out, turn the burner control

knob off and wait at least 1 minute before attempting to light it again.

Proper use of the burners

To achieve maximum efficiency with the least possible gas consumption, keep

the following instructions in mind:

Use the correct pan size for each burner. (See the following table and Fig.

9.)

When the pan comes to a boil, set the knob to a reduced rate position

(small flame icon, Fig. 8).

Always put lids on the pans.

Use only flat-bottomed pans.

Burners

Power Ratings

Pan Diameter

Ultra-Rapid

11000 - 12000 Btu/h

9½" to 10¼"

Semi-Rapid

6000 Btu/h

6¼" to 7"

Fig. 9

Fig. 8

12

WARNINGS:

Burners will only ignite when the corresponding knob has been set to the

Full-on position (large flame icon, Fig. 8).

Matches can be used to ignite the burners during a power outage, but use

caution.

Never leave the appliance unattended when the burners are being used.

Make sure there are no children in the vicinity. In particular, make sure

that the pan handles are correctly positioned. Keep checking on foods that

require oil or other grease to cook since these products can easily catch

on fire.

The machine must not be used by people (including children) with

impaired mental or physical capacities, or without experience of using

electrical devices, unless supervised or instructed by an adult responsible

for their safety and care. Children should not be allowed to play with the

equipment.

Never use aerosol sprays near the appliance when it is operating.

Containers wider than the unit are not recommended.

NOTES:

The use of a gas cooking appliance produces heat and moisture in the

room in which it is installed. The room must therefore be well ventilated.

Intensive and lengthy use of the appliance may require additional

ventilation. This can be achieved by opening a window or by increasing

the power of the mechanical exhaust system if installed.

WARNING!

NEVER use this appliance as a space heater

to heat or warm the room. Doing so may result

in carbon monoxide poisoning and overheating

of the appliance.

13

CLEANING

CAUTION: Before cleaning the appliance, disconnect it from the gas and

electricity supplies.

If you wish to maintain the shine of the ceramic surface, treat the glass with a

silicon-based film product before use to protect the surface against water and

dirt. This protective film is not durable, so it is advised to repeat the

application of the product frequently.

It is very important to clean the cooktop every time you use it, while it is still

warm.

Do not clean using abrasive metal scourers, powder abrasives or corrosive

sprays.

Depending on the degree of dirt, we recommend the following:

For light stains, a damp sponge is sufficient.

Tough, encrusted dirt is easily eliminated using a scraper (Fig. 10), not

supplied with the cooktop, but easy to find in local stores. Use the scraper

carefully to avoid damaging the cooktop.

Traces of liquid spilled from pans can be eliminated with vinegar or lemon

juice.

Try not to allow sugar or sugary foods to fall on the cooktop while

cooking. Should this occur, switch off the cooktop and clean it

immediately with hot water, using a scraper on hot spills.

As time goes by, metallic streaks, discoloring or scratches may appear due

to poor cleaning and the incorrect movement of pans. Scratches are hard

to eliminate but do not affect the correct operation of your cooktop.

Do not use jets of steam to clean the appliance.

The enameled grids, enameled covers "A", "B" and "C", and burner heads "T-M" (see

Figs. 11 and 11c) must also be washed and the ignition elements "AC" and safety cut-

off sensors "TC" (see Fig. 11) must be cleaned. Clean them gently with a small nylon

brush as shown (see fig. 11b) and allow to dry fully. Do not wash them in the

dishwasher. Cleaning operations must be carried out when the cooktop and

Fig. 10

14

components are not hot. The use of metal scouring pads, powder abrasives and

corrosive sprays must be avoided.

Do not allow vinegar, coffee, milk, salt water, lemon juice or tomato juice to remain in

prolonged contact with the surfaces.

WARNINGS:

When reassembling the components, observe the following

recommendations:

Check that the holes in the burner heads "T-M" (Fig. 11-11c) are not blocked by

foreign bodies.

Be sure that the enameled covers "A", "B" and "C" (Figs. 11-11a and 11c) are

correctly positioned on the burner head. The covers are correctly positioned on the

head when they are perfectly stable.

If the opening and closing of any valve is awkward, do not force it but request

urgent intervention by the technical assistance service.

Do not use jets of steam to clean the appliance.

The pan support must be placed in the appropriate centering pins verifying the

perfect stability

To prevent difficulties with lighting, regularly clean the ignition elements (ceramic

and electrode) and safety cut-off switches.

IMPORTANT:

After removing the burners to clean them, be sure that all parts are correctly

positioned before relighting them.

FIG.11

FIG.11a

FIG.11b

FIG.11c

15

SERVICING

Always disconnect the appliance from the electric and gas mains before

proceeding with any servicing operation.

Replacing Components

To replace the components housed inside the appliance, remove the trivets

and the burners from the upper part of the cooktop. Remove the fixing screws

"V" of the burner (Fig. 12) and the knobs by pressure from the hands, in order

to take off the appliance.

After having carried out these operations, the burners (Fig. 13), taps (Fig. 14)

and electrical components can all be replaced (Fig. 15).

It is advisable to change seal "D" (Fig. 14) whenever a tap is replaced to

ensure a perfect tightness.

Greasing the taps (See Fig. 16)

If a tap becomes stiff to operate, it must be immediately greased in

compliance with the following instructions:

1. Remove the tap.

2. Clean the cone and its housing using a cloth soaked in solvent.

3. Lightly grease the cone.

4. Fit the cone back into place, operate it a few times and then remove it

again. Eliminate any excess grease and check that the gas ducts have not

become clogged.

5. Fit all parts back into place, complying with the disassembling order in

reverse.

6. The tight closure test must be done using a foaming liquid. Never use a

flame for this test.

Fig. 12

Fig. 13

Fig. 14

Fig. 15

Fig. 16

16

LIMITED WARRANTY

Within the 48 contiguous United States, for one year from the date of purchase, when this

appliance is operated and maintained according to instructions attached to or furnished with the

product, warrantor will pay for factory-specified parts and repair labor to correct defects in

materials or workmanship. Service must be provided by a designated service company.

Outside the 48 states, all parts are warranted for one year from manufacturing defects. Plastic

parts, shelves and cabinets are warranted to be manufactured to commercially acceptable

standards, and are not covered from damage during handling or breakage.

ITEMS WARRANTOR WILL NOT PAY FOR:

Service calls to correct the installation of your appliance, to instruct you how to use your

appliance, to replace or repair fuses or to correct wiring or plumbing.

Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumable

parts (such as filters) are excluded from warranty coverage.

Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper

installation, installation not in accordance with electrical or plumbing codes, or use of

products not approved by warrantor.

Replacement parts or repair labor costs for units operated outside the United States.

Repairs to parts or systems resulting from unauthorized modifications made to the

appliance.

The removal and reinstallation of your appliance if it is installed in an inaccessible location

or is not installed in accordance with published installation instructions.

DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES

CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE

PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES

OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE

YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR

CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES

OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT

APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO

HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.

WARNING! This product can expose you to chemicals including Nickel (Metallic)

which is known to the State of California to cause cancer.

For more information go to www.P65Warnings.ca.gov

Note: Nickel is a component in all stainless steel and some other metal components

Call customer service toll free in the U.S.A. @ 1-800-932-4267, Monday to Friday 9:00 am. - 5:00 p.m.

(ET).

Order parts online at www.summitappliance.com/support

Felix Storch, Inc.

Summit Appliance Division

770 Garrison Avenue

Bronx, NY 10474

Phone: (718) 893-3900

Fax: (844) 478-8799

Web Site:

www.summitappliance.com

17

TABLE DE CUISSON À GAZ

ENCASTRABLE EN CÉRAMIQUE

Modèle GC443BGL

Mode d'emploi

04059ULSUMNAT (FR) - 07.11.2016

Cher Client,

Nous vous remercions d'avoir choisi notre table de cuisson à gaz en

céramique. Nous vous assurons que cet appareil moderne,

fonctionnel et pratique à la fois, fabriqué avec des matériaux de

première qualité, saura satisfaire pleinement vos exigences.

Ce nouvel appareil est très facile d'utilisation, mais afin d'obtenir les

meilleurs résultats, nous vous recommandons tout particulièrement, de

lire attentivement cette notice avant toute utilisation. Le fabriquant ne

peut être tenu pour responsable en cas de dommages corporels ou

matériels en raison d'une installation incorrecte ou un usage abusif de

l'appareil.

Nous nous réservons le droit d'apporter des modifications à nos

produits, que nous jugeons nécessaires ou utiles, notamment dans

l'intérêt de l'utilisateur, tout en conservant ses caractéristiques

essentielles en termes de fonctionnement et sécurité.

Le personnel de

Felix Storch, Inc.

Summit Appliance Division

Une compagnie enregistrée d'ISO 9001:2015

770 Garrison Avenue

Bronx, New York 10474

www.summitappliance.com

18

TABLE DES MATIÈRES

Précautions importantes ...................................................... 19 - 20

Position des composants ............................................................ 21

Installation ............................................................................. 22 - 25

Installation de la table de cuisson .......................................... 22

Fixation de la table de cuisson .............................................. 23

Ventilation de la pièce ............................................................ 23

Raccordement au gaz ........................................................... 24

Branchement électrique ................................................. 24 - 25

Réglages ....................................................................................... 26

Conversions ................................................................................. 27

Utilisation de la table de cuisson ......................................... 28 - 29

Allumage des brûleurs ........................................................... 28

Utilisation correcte des brûleurs ..................................... 28 - 29

Nettoyage ............................................................................... 30 - 31

Entretien ........................................................................................ 32

Remplacement des composants

Garantie limitée ............................................................................ 36

19

PRÉCAUTIONS IMPORTANTES

Pour tous les appareils :

Le produit doit être installé conformément à la déclaration que

l'installation doit être conforme aux codes locaux ou, en l'absence de

codes locaux, avec le National Fuel Gas Code, ANSI Z223.1 / NFPA

54.

Le produit doit être mis à la terre conformément aux codes locaux ou,

en l'absence de codes locaux, avec le National Electrical Code, ANSI

/ NFPA 70.

Assurez-vous que la connexion de gaz est conforme aux codes et

règlements locaux. En l'absence de codes locaux, les installations doivent

être conformes à la norme nationale américaine, National Fuel Gas Code

ANSI Z223 / NFPA 54 ou canadien CAN / CGA_B 149.1 ou CAN / CGA-

149.2.

Le produit doit être mis à la terre conformément aux codes locaux ou, en

l'absence de ces derniers, au National Electrical Code, NFPA 70

ou la

Canadian Electric Code, CSA C22.1-02.

Cet appareil et son robinet d'arrêt doivent être débranchés du réseau

d'alimentation en gaz lors des essais de pression effectués à une valeur

supérieure à 1/2 psi (3.5 kPa). La pression maximale d'alimentation en

gaz est de 4 pouces d'eau pour le gaz naturel et 11 pouces d'eau pour le

GPL. Le régulateur de pression du gaz est réglé à 1 pouce d'eau au-

dessus de la pression d'admission spécifiée par le fabriquant.

Débranchez toujours l'appareil du réseau d'alimentation électrique avant

toute opération d'entretien.

AVERTISSEMENT :

Le non-respect des instructions du présent manuel peut

être à l'origine d'un incendie ou explosion causant des dommages

matériels, corporels ou le décès.

Ne pas entreposer ou utiliser d'essence ou autres gaz ou liquides

inflammables à proximité de cet ou tout autre appareil.

Que faire si ça sent le gaz :

 N'allumez aucun appareil.

 Ne touchez aucun interrupteur. N'utilisez aucun téléphone se trouvant

dans le bâtiment.

 Appelez immédiatement votre fournisseur de gaz utilisant le téléphone

d'un voisin. Suivez les instructions données par le fournisseur de gaz.

 Si vous n'arrivez pas à joindre votre fournisseur de gaz, contactez les

pompiers.

L'installation et la mise en service doivent être effectuées par un

installateur qualifié, un centre agréé ou le fournisseur de gaz.

Conservez les buses retirées de l'appareil en vue d'un usage futur.

La profondeur maximale des meubles installés au-dessus de la table de

cuisson doit être de 13 pouces (330 mm).

La page charge ...

Summit GC443BGL Le manuel du propriétaire

Summit GC443BGL Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents