Summit GC443BGL Le manuel du propriétaire

Taper
Le manuel du propriétaire
BUILT-IN CERAMIC GAS COOKTOP
Model GC443BGL
Instruction Manual
04059ULSUMNAT (ENG) - 07.11.2016
Dear Customer,
Thank you for buying one of our ceramic gas cooktops. We are sure
that this modern, functional and practical appliance, made using the
finest quality materials, will fully satisfy your requirements.
This new appliance is very easy to use, but in order to obtain the best
results, we strongly recommend that you read this booklet carefully
before use. The manufacturer cannot be considered responsible for
any damages to people or things in the event of incorrect installation or
improper use of this appliance.
We reserve the right to make any changes to our products which we
consider to be necessary or useful, also in the interest of the user,
without affecting the essential characteristics in terms of functionality
and safety.
The staff of
Felix Storch, Inc.
Summit Appliance Division
An ISO 9001:2015 registrated company
770 Garrison Avenue
Bronx, New York 10474
www.summitappliance.com
1
TABLE OF CONTENTS
Important Safeguards .................................................................... 2
Location of Parts ............................................................................ 4
Installation ................................................................................. 5 - 8
Installing the Cooktop .............................................................. 5
Sealing the Cooktop ................................................................ 6
Room Ventilation ..................................................................... 6
Gas Connection ...................................................................... 7
Electrical Connection .......................................................... 7 - 8
Adjustments ................................................................................... 9
Conversions ................................................................................. 10
Using the Cooktop ................................................................ 11 - 12
Lighting the Burners .............................................................. 11
Proper Use of the Burners .............................................. 11 - 12
Cleaning ................................................................................. 13 - 14
Servicing ....................................................................................... 15
Replacing Components
Limited Warranty .......................................................................... 16
2
IMPORTANT SAFEGUARDS
For all appliances:
the installation of appliances designed for manufactured (mobile)
homes must conform with the Manufactured Home Construction and
Safety Standard, Title 24, CFR, Part 3280 (formerly the Federal
Standard for Mobile Home Construction and Safety, Title 24, HUD
(Part 280)), or when such standard is not applicable, the Standard for
Manufactured Home Installations, ANSI/NCSBCS 225.1, or with
applicable local codes.
Leak testing of the appliance shall be conducted according to the
manufacturer’s instructions.
Assure that gas connection conforms with local codes and ordinances. In
the absence of local codes, installations must conform with American
National Standard, National Fuel Gas Code ANSI Z223/NFPA 54 or
Canadian CAN/CGA_B 149.1 or CAN/CGA-149.2.
The product must be electrically grounded in accordance with local codes
or, in the absence of local codes, with the National Electrical Code, NFPA
70
or the Canadian Electric Code, CSA C22.1-02.
The appliance and its individual shutoff valve must be disconnected from
the gas supply piping system during any pressure testing of that system at
test pressure in excess of 1/2 psi (3.5 kPa). The maximum gas supply
pressure is 4 inch WC (water column) for natural gas and 11 inch WC for
LP. The gas
pressure regulator provided is regulated to 1 inch WC above
the manufacturer's
specified manifold pressure.
Always disconnect the electrical supply before servicing the appliance.
WARNING:
If the information in this manual is
not followed exactly, a fire or explosion could
result causing property damage, physical
injury or death.
Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
What to do if you smell gas:
Do not try to turn on any appliance.
Do not touch any electrical switch. Do not
use any phone in your building.
3
Immediately call your gas supplier from a
neighbor's phone. Follow the gas supplier's
instructions.
If you cannot reach your gas supplier, call
the fire department.
Installation and service must be performed by
a qualified installer, service agency or the gas
supplier.
Save any nozzles removed from the appliance for future use.
The maximum depth of cabinets installed above the cooktop should be 13
inches (330 mm).
Keep the appliance clear and free from combustible materials, gasoline
and other flammable vapors and liquids.
Do not obstruct the flow of gas or block any air vents.
The appliance must be isolated from the gas supply piping system by
closing its individual manual shut-off valve during any pressure testing of
the gas supply piping system at test pressures equal to or less than 1/2 psi
(3.5 kPa).
SAVE THESE INSTRUCTIONS
4
LOCATION OF PARTS
Part No.
Description
Heat supplied
1
Ultra-rapid gas burner
11000-12000 Btu/h
3
Semi-rapid gas burner
6000 Btu/h
6
Enameled steel pan support for
ultra-rapid burner
7
Enameled steel pan support for
semi-rapid burners
8
Enameled steel pan support for
wok (only on ultra-rapid gas
burner)
10
Burner no. 1 control knob
12
Burner no. 3 control knob
NOTICE: This appliance has been manufactured for residential use only.
MODEL: GC443BGL
5
INSTALLATION
Installation, adjustment of controls and maintenance must only be
carried out by qualified personnel.
Incorrect installation may cause damage to persons, animals or property
for which the Manufacturer will not be considered responsible. During
the life of the system, the automatic safety or regulating devices on the
appliance may only be modified by the manufacturer or by his duly
authorized dealer.
Installing the Cooktop
Check that the appliance is in good condition after having removed the outer
packaging and internal wrappings from around the various loose parts. In
case of doubt, do not use the appliance and contact qualified personnel.
Never leave packaging materials (cardboard, bags, Styrofoam, nails,
etc.) within the reach of children since these items could become
sources of danger.
The measurements of the opening made in the top of the modular cabinet or
island and into which the cooktop will be installed are indicated in Fig. 1 and
the following chart. Always comply with the measurements given for the hole
into which the appliance will be recessed (see Figs. 1 and 2).
Use These Dimensions (in inches)
Model No.
B
C
D
E
GC443BGL
13-5/8
3-1/8
5
3
30"
Min.
6"
Fig. 1
Fig. 2
6
Sealing the Cooktop
The cooktop has a special seal that prevents liquid from getting into the
cabinet below. Follow these instructions exactly in order to apply this seal
correctly:
Detach the seals from their backing, checking that the transparent protection
still adheres to the seal itself.
Turn the cooktop over and correctly position seal "E" (Fig. 3) under the edge
of the cooktop itself so that the outer side of the seal perfectly matches the
outer edge of the cooktop. The ends of the strips must fit together without
overlapping.
Once the seals are securely and evenly fixed to the cooktop, press them into
place with the fingers and remove the strip of protective paper from the seal.
Set the plate into the hole made in the cabinet.
FIG. 3
FIG. 4
Fix the hob with the proper brackets “S” and fit the prominent part into the
porthole “H” on the bottom; turn the screw “F” until the bracket “S” stick on the
top (fig. 4). In fastening the brackets, do not use a mechanical or electric
screwdriver. Instead, use a hand-operated screwdriver and exert only
moderate force.
The adjacent walls (left, right or behind) that exceed the cooktop in height
must be at a minimum distance from the cut hole as indicated in Fig. 1 and the
chart on the preceding page.
In order to avoid accidentally touching the hot cooktop bottom, it is necessary
to put a horizontal wooden insert, attached by screws, at a minimum distance
of 6" below the lower surface of the cooktop (see Fig. 1).
Room Ventilation
To ensure proper operation of the appliance, be sure that the room where it is
installed has adequate ventilation.
The appliance should not be installed with a ventilation system that
blows air downward toward the appliance. It may cause ignition and
combustion problems with the gas cooking appliance resulting in
personal injury or unintended operation.
7
Gas Connection
Natural Gas and Propane Gas
Natural gas installations require the connection of a gas regulator to the
cooktop. You will find this regulator among the accessories supplied with the
appliance.
Assemble the regulator (noting the direction of gas flow) and transition pieces
(supplied) in accordance with the figure below.
The maximum gas supply
pressure (in accordance with the
inlet pressure rating of the
pressure regulator supplied).
The gas supply pressure for
testing the regulator setting the
pressure shall be at least 1 in.
water column (249 Pa) above the
specified manifold pressure).
The transition piece on the supply side of the regulator must be provided by
the installer. Unions compatible with the hose fittings must be used and
connections tested for gas leaks.
Be sure that the supply connection point is accessible with the appliance
installed.
WARNING: Be sure the hose assembly is restrained from accidental contact
with the flue or flue outlet of an under-counter oven.
Electrical Connection
The electrical connections of the appliance must be carried out in compliance
with local standards and provisions.
Before connecting the appliance, check that:
1. The electrical capacity of the main electrical supply and current sockets suit
the maximum power rating of the appliance. (See the data label attached
to the bottom of the cooktop.)
2. The socket or system has an efficient ground connection in compliance
with local standards and provisions. The manufacturer is not responsible
for failure to comply with these provisions.
8
When the appliance is connected to electrical power by a socket:
Fit a standard plug suited to the load indicated on the data label to the
cable.
Fit the wires following Fig. 5, noting the following correspondences:
Letter L (live) = wire
Letter N (neutral) = wire
Ground symbol = green or yellow-green wire
Never use adapters or shunts for connection since these could create false
contacts and lead to dangerous overheating.
The outlet must be accessible after the cooktop is built in.
When the appliance is connected directly to the electrical main:
Install an omnipolar circuit-breaker between the appliance and the electrical
main. This circuit-breaker should be sized in compliance with local
installation regulations.
Remember that the ground wire must not be interrupted by the circuit-
breaker.
For optimum safety, the electrical connection may also be protected by a
high-sensitivity differential circuit-breaker.
You are strongly advised to fix the yellow-green ground wire to an efficient
grounding system
Fig. 5
9
ADJUSTMENTS
Always disconnect the appliance from the electrical power source
before making any adjustments. All seals must be replaced by the
technician when any adjustments are completed.
The burners do not require any regulation of incoming air.
Taps
"Reduced rate" adjustment:
1. Switch on the burner and turn the relative knob to the “Reduced rate”
position (small flame fig. 8 page 11).
2. Remove knob “M” (fig. 6 and 6/A) of the tap, which is simply pressed on to
its rod.
3. The by-pass for minimal rate regulation can be: beside the tap (fig. 6) or
inside the shaft. In any case, to access the regulation, it can be done
through the insertion of a small screwdriver ‘’D’’ beside the tap (fig. 6) or in
the hole ‘’C’’ inside the shaft of the tap (fig 6/A).
Turn the throttle screw to the right or left until the burner flame has been
adequately regulated to the “Reduced rate” position.
The flame should not be too low: the lowest small flame should be continuous
and steady. Re-assemble the several components.
It is understood that only burners operating with Natural Gas or City Gas
should be subjected to the above-mentioned adjustments. The screw
must be fully locked when the burners operate with Propane (turn
clockwise).
Fig. 6
FIG. 6/A
10
CONVERSIONS
Replacing Nozzles
The burners can be adapted to suit different
types of gas by fitting the nozzles that corres-
pond to the gas used. To do this, it is
necessary to remove the burner heads and
use a straight key "B" to unscrew the nozzle
"A" (see Fig. 7) and replace it with a nozzle
corresponding to the gas used.
Be sure the nozzle is seated tightly.
After making these replacements, the technician must regulate the
burners as described in Adjustments on the previous page and reset
any seals. He should affix the label corresponding to the new gas type
to replace the label previously applied. The nozzles and labels may be
included in a kit with the unit, or obtained from the dealer.
How to change the setting of the pressure regulator supplied with the
cooktop:
The gas regulator was set up to Natural Gas. To convert to LP Gas:
1. Unscrew the aluminum cap
2. Remove and turn the plastic pin 180°
3. Screw in the plastic pin
4. Screw in the aluminum cap
To make it easier for the fitter, we have prepared a table indicating the flow
capacities, the heat capacities of the burners, the diameter of the nozzles and
the working pressure for the various types of gas.
Burners
Gas
Normal
Manifold
Pressure,
inches water
column
Injector
Diameter,
1/100 mm
Nominal Heat
Input (Btu/h)
No.
Description
Min.
Max.
1
Ultra-Rapid
Propane HD-5
Natural Gas
11
4
94
170
5100
5100
11000
12000
3
Semi-Rapid
Propane HD-5
Natural Gas
11
4
70
120
2400
2400
6000
6000
1
3
1
3
Arrangement
of Burners
Fig. 7
11
USING THE COOKTOP
Lighting the burners
A diagram is screened beside each knob on the control panel of your cooktop.
This diagram indicates to which burner the knob in question corresponds.
After having opened the gas main or bottled gas tap, light the burners as
described below:
The knobs of the burners are equipped with a safety cut-off device. They
must be turned in a counter-clockwise direction until they reach the full-on
position (large flame icon, Fig. 8) and come to a stop. Now push down on the
knob. The burner should ignite in 2 or 3 seconds. Keep the knob depressed
as you turn it toward the reduced rate position (small flame icon, Fig. 8) to
adjust the flame. Should the flame accidentally go out, turn the burner control
knob off and wait at least 1 minute before attempting to light it again.
Proper use of the burners
To achieve maximum efficiency with the least possible gas consumption, keep
the following instructions in mind:
Use the correct pan size for each burner. (See the following table and Fig.
9.)
When the pan comes to a boil, set the knob to a reduced rate position
(small flame icon, Fig. 8).
Always put lids on the pans.
Use only flat-bottomed pans.
Burners
Power Ratings
Pan Diameter
Ultra-Rapid
11000 - 12000 Btu/h
" to 10¼"
Semi-Rapid
6000 Btu/h
6¼" to 7"
Fig. 9
Fig. 8
12
WARNINGS:
Burners will only ignite when the corresponding knob has been set to the
Full-on position (large flame icon, Fig. 8).
Matches can be used to ignite the burners during a power outage, but use
caution.
Never leave the appliance unattended when the burners are being used.
Make sure there are no children in the vicinity. In particular, make sure
that the pan handles are correctly positioned. Keep checking on foods that
require oil or other grease to cook since these products can easily catch
on fire.
The machine must not be used by people (including children) with
impaired mental or physical capacities, or without experience of using
electrical devices, unless supervised or instructed by an adult responsible
for their safety and care. Children should not be allowed to play with the
equipment.
Never use aerosol sprays near the appliance when it is operating.
Containers wider than the unit are not recommended.
NOTES:
The use of a gas cooking appliance produces heat and moisture in the
room in which it is installed. The room must therefore be well ventilated.
Intensive and lengthy use of the appliance may require additional
ventilation. This can be achieved by opening a window or by increasing
the power of the mechanical exhaust system if installed.
WARNING!
NEVER use this appliance as a space heater
to heat or warm the room. Doing so may result
in carbon monoxide poisoning and overheating
of the appliance.
13
CLEANING
CAUTION: Before cleaning the appliance, disconnect it from the gas and
electricity supplies.
If you wish to maintain the shine of the ceramic surface, treat the glass with a
silicon-based film product before use to protect the surface against water and
dirt. This protective film is not durable, so it is advised to repeat the
application of the product frequently.
It is very important to clean the cooktop every time you use it, while it is still
warm.
Do not clean using abrasive metal scourers, powder abrasives or corrosive
sprays.
Depending on the degree of dirt, we recommend the following:
For light stains, a damp sponge is sufficient.
Tough, encrusted dirt is easily eliminated using a scraper (Fig. 10), not
supplied with the cooktop, but easy to find in local stores. Use the scraper
carefully to avoid damaging the cooktop.
Traces of liquid spilled from pans can be eliminated with vinegar or lemon
juice.
Try not to allow sugar or sugary foods to fall on the cooktop while
cooking. Should this occur, switch off the cooktop and clean it
immediately with hot water, using a scraper on hot spills.
As time goes by, metallic streaks, discoloring or scratches may appear due
to poor cleaning and the incorrect movement of pans. Scratches are hard
to eliminate but do not affect the correct operation of your cooktop.
Do not use jets of steam to clean the appliance.
The enameled grids, enameled covers "A", "B" and "C", and burner heads "T-M" (see
Figs. 11 and 11c) must also be washed and the ignition elements "AC" and safety cut-
off sensors "TC" (see Fig. 11) must be cleaned. Clean them gently with a small nylon
brush as shown (see fig. 11b) and allow to dry fully. Do not wash them in the
dishwasher. Cleaning operations must be carried out when the cooktop and
Fig. 10
14
components are not hot. The use of metal scouring pads, powder abrasives and
corrosive sprays must be avoided.
Do not allow vinegar, coffee, milk, salt water, lemon juice or tomato juice to remain in
prolonged contact with the surfaces.
WARNINGS:
When reassembling the components, observe the following
recommendations:
Check that the holes in the burner heads "T-M" (Fig. 11-11c) are not blocked by
foreign bodies.
Be sure that the enameled covers "A", "B" and "C" (Figs. 11-11a and 11c) are
correctly positioned on the burner head. The covers are correctly positioned on the
head when they are perfectly stable.
If the opening and closing of any valve is awkward, do not force it but request
urgent intervention by the technical assistance service.
Do not use jets of steam to clean the appliance.
The pan support must be placed in the appropriate centering pins verifying the
perfect stability
To prevent difficulties with lighting, regularly clean the ignition elements (ceramic
and electrode) and safety cut-off switches.
IMPORTANT:
After removing the burners to clean them, be sure that all parts are correctly
positioned before relighting them.
FIG.11
FIG.11a
FIG.11b
FIG.11c
15
SERVICING
Always disconnect the appliance from the electric and gas mains before
proceeding with any servicing operation.
Replacing Components
To replace the components housed inside the appliance, remove the trivets
and the burners from the upper part of the cooktop. Remove the fixing screws
"V" of the burner (Fig. 12) and the knobs by pressure from the hands, in order
to take off the appliance.
After having carried out these operations, the burners (Fig. 13), taps (Fig. 14)
and electrical components can all be replaced (Fig. 15).
It is advisable to change seal "D" (Fig. 14) whenever a tap is replaced to
ensure a perfect tightness.
Greasing the taps (See Fig. 16)
If a tap becomes stiff to operate, it must be immediately greased in
compliance with the following instructions:
1. Remove the tap.
2. Clean the cone and its housing using a cloth soaked in solvent.
3. Lightly grease the cone.
4. Fit the cone back into place, operate it a few times and then remove it
again. Eliminate any excess grease and check that the gas ducts have not
become clogged.
5. Fit all parts back into place, complying with the disassembling order in
reverse.
6. The tight closure test must be done using a foaming liquid. Never use a
flame for this test.
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
16
LIMITED WARRANTY
Within the 48 contiguous United States, for one year from the date of purchase, when this
appliance is operated and maintained according to instructions attached to or furnished with the
product, warrantor will pay for factory-specified parts and repair labor to correct defects in
materials or workmanship. Service must be provided by a designated service company.
Outside the 48 states, all parts are warranted for one year from manufacturing defects. Plastic
parts, shelves and cabinets are warranted to be manufactured to commercially acceptable
standards, and are not covered from damage during handling or breakage.
ITEMS WARRANTOR WILL NOT PAY FOR:
Service calls to correct the installation of your appliance, to instruct you how to use your
appliance, to replace or repair fuses or to correct wiring or plumbing.
Service calls to repair or replace appliance light bulbs or broken glass shelves. Consumable
parts (such as filters) are excluded from warranty coverage.
Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper
installation, installation not in accordance with electrical or plumbing codes, or use of
products not approved by warrantor.
Replacement parts or repair labor costs for units operated outside the United States.
Repairs to parts or systems resulting from unauthorized modifications made to the
appliance.
The removal and reinstallation of your appliance if it is installed in an inaccessible location
or is not installed in accordance with published installation instructions.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE
PRODUCT REPAIR AS PROVIDED HEREIN. IMPLIED WARRANTIES, INCLUDING WARRANTIES
OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE
YEAR. WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES
OF MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT
APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO
HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE.
WARNING! This product can expose you to chemicals including Nickel (Metallic)
which is known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov
Note: Nickel is a component in all stainless steel and some other metal components
Call customer service toll free in the U.S.A. @ 1-800-932-4267, Monday to Friday 9:00 am. - 5:00 p.m.
(ET).
Order parts online at www.summitappliance.com/support
Felix Storch, Inc.
Summit Appliance Division
770 Garrison Avenue
Bronx, NY 10474
Phone: (718) 893-3900
Fax: (844) 478-8799
Web Site:
www.summitappliance.com
17
TABLE DE CUISSON À GAZ
ENCASTRABLE EN CÉRAMIQUE
Modèle GC443BGL
Mode d'emploi
04059ULSUMNAT (FR) - 07.11.2016
Cher Client,
Nous vous remercions d'avoir choisi notre table de cuisson à gaz en
céramique. Nous vous assurons que cet appareil moderne,
fonctionnel et pratique à la fois, fabriqué avec des matériaux de
première qualité, saura satisfaire pleinement vos exigences.
Ce nouvel appareil est très facile d'utilisation, mais afin d'obtenir les
meilleurs résultats, nous vous recommandons tout particulièrement, de
lire attentivement cette notice avant toute utilisation. Le fabriquant ne
peut être tenu pour responsable en cas de dommages corporels ou
matériels en raison d'une installation incorrecte ou un usage abusif de
l'appareil.
Nous nous réservons le droit d'apporter des modifications à nos
produits, que nous jugeons nécessaires ou utiles, notamment dans
l'intérêt de l'utilisateur, tout en conservant ses caractéristiques
essentielles en termes de fonctionnement et sécurité.
Le personnel de
Felix Storch, Inc.
Summit Appliance Division
Une compagnie enregistrée d'ISO 9001:2015
770 Garrison Avenue
Bronx, New York 10474
www.summitappliance.com
18
TABLE DES MATIÈRES
Précautions importantes ...................................................... 19 - 20
Position des composants ............................................................ 21
Installation ............................................................................. 22 - 25
Installation de la table de cuisson .......................................... 22
Fixation de la table de cuisson .............................................. 23
Ventilation de la pièce ............................................................ 23
Raccordement au gaz ........................................................... 24
Branchement électrique ................................................. 24 - 25
Réglages ....................................................................................... 26
Conversions ................................................................................. 27
Utilisation de la table de cuisson ......................................... 28 - 29
Allumage des brûleurs ........................................................... 28
Utilisation correcte des brûleurs ..................................... 28 - 29
Nettoyage ............................................................................... 30 - 31
Entretien ........................................................................................ 32
Remplacement des composants
Garantie limitée ............................................................................ 36
19
PRÉCAUTIONS IMPORTANTES
Pour tous les appareils :
Le produit doit être installé conformément à la déclaration que
l'installation doit être conforme aux codes locaux ou, en l'absence de
codes locaux, avec le National Fuel Gas Code, ANSI Z223.1 / NFPA
54.
Le produit doit être mis à la terre conformément aux codes locaux ou,
en l'absence de codes locaux, avec le National Electrical Code, ANSI
/ NFPA 70.
Assurez-vous que la connexion de gaz est conforme aux codes et
règlements locaux. En l'absence de codes locaux, les installations doivent
être conformes à la norme nationale américaine, National Fuel Gas Code
ANSI Z223 / NFPA 54 ou canadien CAN / CGA_B 149.1 ou CAN / CGA-
149.2.
Le produit doit être mis à la terre conformément aux codes locaux ou, en
l'absence de ces derniers, au National Electrical Code, NFPA 70
ou la
Canadian Electric Code, CSA C22.1-02.
Cet appareil et son robinet d'arrêt doivent être débranchés du réseau
d'alimentation en gaz lors des essais de pression effectués à une valeur
supérieure à 1/2 psi (3.5 kPa). La pression maximale d'alimentation en
gaz est de 4 pouces d'eau pour le gaz naturel et 11 pouces d'eau pour le
GPL. Le régulateur de pression du gaz est réglé à 1 pouce d'eau au-
dessus de la pression d'admission spécifiée par le fabriquant.
Débranchez toujours l'appareil du réseau d'alimentation électrique avant
toute opération d'entretien.
AVERTISSEMENT :
Le non-respect des instructions du présent manuel peut
être à l'origine d'un incendie ou explosion causant des dommages
matériels, corporels ou le décès.
Ne pas entreposer ou utiliser d'essence ou autres gaz ou liquides
inflammables à proximité de cet ou tout autre appareil.
Que faire si ça sent le gaz :
N'allumez aucun appareil.
Ne touchez aucun interrupteur. N'utilisez aucun téléphone se trouvant
dans le bâtiment.
Appelez immédiatement votre fournisseur de gaz utilisant le téléphone
d'un voisin. Suivez les instructions données par le fournisseur de gaz.
Si vous n'arrivez pas à joindre votre fournisseur de gaz, contactez les
pompiers.
L'installation et la mise en service doivent être effectuées par un
installateur qualifié, un centre agréé ou le fournisseur de gaz.
Conservez les buses retirées de l'appareil en vue d'un usage futur.
La profondeur maximale des meubles installés au-dessus de la table de
cuisson doit être de 13 pouces (330 mm).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37

Summit GC443BGL Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues