Haier QDT125 Series Le manuel du propriétaire

Marque: Haier

Modèle: QDT125 Series

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Owner's Manual

Manuel d’utilisation

Manual del propietario

QDT125 Series

18” Built-In Dishwasher

Lave-Vaisselle Incorpere 18”

Lavavajillas Empotrado 18”

49-55125-1 05-18 GEA

2 49-55125-1

ENGLISH

RECORD KEEPING

Thank you for purchasing this Haier product. This Owner's

Manual will help you get the best performance from your new

dishwasher.

For future reference, record the model and serial number

located on the the tub wall just inside the door.

Staple your proof of purchase to this manual to aid in

obtaining warranty service if needed.

____________________________________________________

Model number

____________________________________________________

Serial number

____________________________________________________

Date of purchase

TABLE OF CONTENTS

SAFETY INFORMATION ............................................................................................3

USING THE DISHWASHER. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Getting Started ........................................................................................................ 5

Dispensers ............................................................................................................ 6

Loading. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

CARE AND CLEANING ............................................................................................10

TROUBLESHOOTING TIPS ........................................................................................12

LIMITED WARRANTY .............................................................................................15

CONSUMER SUPPORT ........................................................................................... 16

49-55125-1 3

ENGLISH

SAFETY INFORMATION

WARNING

For your safety, the information in this manual must be followed to minimize the

risk of fire, explosion, electric shock, and to prevent property damage, personal injury, or death.

WARNING

PROPER INSTALLATION AND MAINTENANCE

This dishwasher must be properly installed and located in accordance with the Installation Instructions before it is used. If

you did not receive an Installation Instructions sheet with your dishwasher, you can receive one by visiting our Website at

haierappliances.com.

Connect the dishwasher/appliance to a grounded

metal, permanent wiring system; or run an equipment-

grounding conductor with the circuit conductors and

connect to the equipment-grounding terminal or lead of

the appliance.

Improper connection of the equipment-grounding

conductor can result in a risk of electric shock. Check

with a qualified electrician or service representative

if you are in doubt whether the appliance is properly

grounded.

Dispose of discarded appliances and shipping or packing

material properly.

Do not attempt to repair or replace any part of your

dishwasher unless it is specifically recommended in

this manual. All other servicing should be referred to a

qualified technician.

Use only cord kit WX09X70910 or hard-wire to building

electrical. Failure to follow this instruction, could result

in risk of fire and personal injury.

To minimize the possibility of electric shock, disconnect

this appliance from the power supply before attempting

any maintenance.

NOTE: Turning the dishwasher off does not disconnect

the appliance from the power supply. We recommend

having a qualified technician service your appliance.

WARNING

WHEN USING YOUR DISHWASHER, FOLLOW BASIC PRECAUTIONS,

INCLUDING THE FOLLOWING:

Use this appliance only for its intended purpose as

described in this Owner’s Manual.

Use only detergents or wetting agents recommended

for use in a dishwasher and keep them out of reach

of children. Using a detergent that is not specifically

designed for dishwashers will cause the dishwasher to

fill with suds.

Locate sharp items so that they are not likely to damage

the door seal.

Load sharp knives with the handles up to reduce the risk

of cut-type injuries.

Do not wash plastic items unless marked dishwasher

safe or the equivalent. For plastic items not so marked,

check the manufacturer’s recommendations.

Do not operate your dishwasher unless all enclosure

panels are properly in place.

Do not tamper with controls.

Do not abuse, sit on or stand on the door or dish rack of

the dishwasher.

To reduce the risk of injury, do not allow children to play

with, on or inside this appliance at any time.

Do not store or use combustible materials including

gasoline or other flammable liquids or vapors in the

vicinity of this or any other appliance.

Small parts can be a choke hazard to small children if

removed from the dishwasher. Keep out of reach of

small children.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

4 49-55125-1

ENGLISH

READ AND SAVE THESE INSTRUCTIONS

SAFETY INFORMATION

IMPORTANT SAFETY INFORMATION

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE

WARNING

WATER HEATER SAFETY

Under certain conditions, hydrogen gas may be produced in a water heater that has not been used for two or more weeks.

HYDROGEN GAS IS EXPLOSIVE.

If the hot water has not been used for two or more weeks, prevent the possibility of damage or injury by turning on all hot

water faucets and allowing them to run for several minutes. Do this before using any electrical appliance connected to the

hot water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do

not smoke, use an open flame, or use the appliance during this process.

TO PREVENT MINOR INJURY AND PROPERTY DAMAGE

During or after wash cycle, contents may be hot to the

touch. Use care before handling.

Close supervision is necessary if this appliance is used

by or near children. Do not allow children to play around

the dishwasher when closing the door, closing the upper

rack, or while vertically adjusting the upper rack due to

the possibility of small fingers being pinched.

Non-Dishware Items: Do not wash items such as

electronic air cleaner filters, furnace filters and paint

brushes in your dishwasher. Damage to the dishwasher

and discoloration or staining of the dishwasher may

result.

WARNING

RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE DISHWASHER

Junked or abandoned dishwashers are dangerous…even if they will sit for “just a few

days.” If you are getting rid of your dishwasher, please follow the instructions below to

help prevent accidents.

Do not allow children to play with, on, or inside this or any discarded appliance.

Take off the door of the washing compartment or remove the latch by disengaging

the two retaining snaps using a flat-blade screwdriver (as shown).

CAUTION

ELECTRICAL REQUIREMENTS

This appliance must be supplied with 120V, 60 Hz, and

connected to an individual, properly grounded branch

circuit, protected by a 15 or 20 amp circuit breaker or

time-delay fuse.

If the electric supply provided does not meet the above

specifications, it is recommended that a licensed

electrician install an approved outlet.

Your dishwasher circuit should not be used for any

other appliance while the dishwasher is in operation as the

dishwasher requires the full capacity of the circuit.

CAUTION

NOTICE

ʄ

If your dishwasher is connected to a wall switch, ensure

that the switch is on prior to use.

ʄ

If you choose to turn the wall switch off between wash

cycles, allow 5-10 seconds after turning the switch on

before touching Start to allow the control to initialize.

ʄ

Use only powder, Finish

Quantum

Automatic

Dishwashing Detergent, liquid detergents or rinse

agents recommended for use in a dishwasher and keep

them out of the reach of children. Finish

Quantum

Automatic Dishwashing Detergent, and Finish

Jet-

Dry

Rinse Aid rinse agents have been approved for use

in all Haier Appliances dishwashers.

Disengage

both

retaining

snaps

49-55125-1 5

ENGLISH

USING THE DISHWASHER

Features and appearance will vary throughout this manual

SELECT CYCLE

Open the door and press the Cycle Select pad for the desired wash cycle. The light next to the Cycle Select pad will be

lit to indicate which wash cycle has been selected.

NOTE: Cycle times vary based on soil level, water temperature, and options selected.

The cycle must be selected with the door in the open position. The cycle will not start until the Start pad is pushed and

the door is closed within 4 seconds.

AutoSense This cycle automatically senses the soil level and adjusts the wash cycle accordingly. It is meant for daily,

regular, or typical use to completely wash a full load of normally soiled dishes and is designed to conserve

both water and energy. NOTE: AutoSense was used to rate the energy efficiency of this dishwasher.

Heavy This cycle is meant for heavily soiled dishes, cookware, pots, or pans with dried-on or baked-on soils.

Everyday dishes are safe to be used in this cycle.

Light This cycle is for lightly soiled dishes. It is safe for china and crystal with no options selected.

LOAD DISHWASHER

For best dishwashing results, follow the loading guidelines found in the Loading section. No pre-rinsing of normal food

soil is required. Scrape off hard soils, including bones, toothpicks, skins, and seeds. Remove leafy vegetables, meat

trimmings, and excessive amounts of grease or oil.

ADD DETERGENT

Add needed amount of detergent to the detergent dispenser. Use detergent such as Finish

Quantum

Automatic

Dishwashing Detergent. See Dispensers section.

ADD RINSE AGENT

Add rinse agent such as Finish

Jet-Dry

Rinse Aid to the rinse agent dispenser. See Dispensers section. NOTE: The

use of rinse aid can further enhance the dishwasher’s drying performance.

SELECT OPTIONS

Wash

Temp

Allows you to select a higher wash temperature. These options are only available for Heavy and

AutoSense cycles. Press the Wash Temp pad until the light next to the desired option comes on.

Boost This option raises the water temperature and extends the cycle time in order to achieve better wash

performance.

Sanitize

This option raises the water temperature in the final rinse to sanitize your dishware. The cycle length may vary

depending on the temperature of your inlet water.

NOTE: Cycles using this option are monitored for sanitization requirements. If the cycle is interrupted

during or after the main wash portion or if the incoming water temperature is so low that adequate water

heating cannot be achieved, the sanitizing conditions may not be met. In these cases, the Sanitized

light will not illuminate at the end of the cycle. Utilizing this option will modify the cycle to meet the

requirements of Section 6, NSF 184 for soil removal and sanitization efficacy.

NOTE: NSF certified residential dishwashers are not intended for licensed food establishments.

Delay Start This option allows you to delay the start of a wash cycle for up to 12 hours. With the door open and a

cycle selected, press the Delay Start pad to choose the number of hours you want to delay the start of

the wash cycle. The hours will show in the display window.

NOTE: You may cancel the Delay Start timer by holding the Start pad for 3 seconds. This will also cancel

the wash cycle.

Control

Lock

You can lock the controls to prevent selections from being made. You can also lock the controls after

you have started a cycle to prevent cycle changes. For example, children cannot accidentally start the

dishwasher by pressing pads with this option selected.

To LOCK/UNLOCK the dishwasher control, press and hold the Cycle Select and Wash Temp pads for 3

seconds. The lock control light ( ) will turn on to indicate the control is locked and will turn off to indicate

the control is unlocked.

Sanitized

Clean

Cycle

Select

Wash

Temp

Delay

Start

AutoSense

Heavy

Light

Boost

Sanitize

1-12 hrs

Start

Hold 3 Sec

Hold 3 Sec To Cancel

6 49-55125-1

ENGLISH

USING THE DISHWASHER

START DISHWASHER

Start Press the Start pad and close the door within 4 seconds to start the cycle or begin the Delay Start

countdown. The Start light will turn on. The wash cycle will begin after 10 seconds and then pump out for

60 seconds prior to filling the dishwasher with water. To activate the display, press any pad with the door

open.

Interrupt

or Pause

To interrupt or pause a cycle, slowly open the door. Opening the door will cause the wash cycle to pause.

The dishwasher will beep every minute to remind you to close the door. To restart or resume the cycle,

press Start, and close the door within 4 seconds. If the door is not closed within 4 seconds, the Start light

will start blinking and the dishwasher will beep once every minute to signal that the cycle did not restart. If

the Start light is blinking, the dishwasher is waiting for input.

Cancel To cancel a wash cycle, press and hold the Start pad for 3 seconds and close door.

The dishwasher will dr

ain, emit a beep sound, and the wash cycle light will turn off.

INDICATOR LIGHTS

Sanitized Displayed at end of the cycle when Wash Temp - Sanitize has been selected and dishwasher has met

requirements for sanitization. See Wash Temp - Sanitize, for complete description. Opening the door will

turn off the light.

Clean Displayed when a wash cycle is complete. The light stays on as a reminder that the dishes are clean.

Opening the door will turn the light off.

DISPLAY

Time

Remaining

During operation, the display shows the total number of minutes remaining in the cycle. During a delay

start, the display will show hours of time remaining until the cycle starts.

CHECK THE WATER TEMPERATURE

The entering water should be at least 120°F (49°C) and not

more than 150°F (66°C) for effective cleaning and to prevent

dish damage. Check the water temperature with a candy or

meat thermometer.

Turn on the hot water faucet nearest the dishwasher,

place the thermometer in a glass and let the water run

continuously into the glass until the temperature stops rising.

SABBATH/DOOR WAKE UP MODE

To turn this option ON/OFF, press and hold the Start and

Wash Temp buttons for 5 seconds, close the door and wait 3

minutes for the dishwasher to go into sleep mode. In the OFF

mode, the control display, control sounds, and interior lights

(on some models) will not respond to the door opening/

closing. This mode can be used when observing certain

religious holidays such as the Sabbath. To activate the control

and interior lights (on some models), press any button.

DISPENSERS

Use a Rinse Agent

Rinse agents, such as Finish® Jet-Dry® Rinse Aid are

designed for great drying action and to protect against spots

and film build-up on your dishes, glasses, flatware, cookware,

and plastic.

Filling the Rinse Agent Dispenser

The rinse agent dispenser holds 3.9 oz. (115 ml) of rinse

agent. Under normal conditions, this will last approximately

one month.

Make sure the dishwasher door is fully open.

Open the dispenser door. (Rinse agent compartment is

on the right side of dispenser.)

Slowly add rinse agent until the cup is full. You may need

to pause several times to allow rinse aid to settle.

Clean up any spilled rinse agent with a damp cloth to

prevent foam from forming inside the dishwasher.

Close the dispenser door.

49-55125-1 7

ENGLISH

USING THE DISHWASHER

DETERGENT DISPENSER

To open, press the button and the cover will flip back. The

detergent dispenser has two compartments. The pre-wash

compartment is the smaller compartment on the left side.

Use the pre-wash compartment only when your water is

extremely hard or when you have a heavy soiled load. The

pre-wash compartment is not used when tablet or packet

detergents are used.

NOTE: Do not block detergent dispenser with large or tall

utensils.

You may use tablet, packet, powder, liquid or gel automatic

dishwasher detergent. Make sure you use only detergents

specifically labeled for use in automatic dishwashers. Never

use liquid hand dish detergent in an automatic dishwasher.

Sudsing and poor wash performance will result with the use of

improper detergents.

Detergents should be stored in a dry location and in their

original container to prevent loss of effectiveness. Place

detergent in the cup just prior to starting the dishwasher

and then close the cover. The cover will open during the

wash cycle.

FILLING THE DETERGENT

DISPENSER

We recommend using detergent in tablet or packet form.

Independent testing has shown this form of detergent

is very effective in the dishwasher. Finish

Quantum

Powerball

is an example of this type of detergent. Simply

put a tablet or packet into the main wash compartment and

close the detergent cup cover. Please notice that the tablet

or packet must be placed in the main wash compartment

of the detergent cup. If the tablet or packet is placed in

the prewash compartment or tossed in the bottom of the

dishwasher, the detergent will be flushed down the drain in

a very short period of time and will thus be wasted. Wash

performance will be very poor as a result.

If you choose to use detergent in powder, liquid or gel form,

the amount of detergent you use will be determined by

the hardness of your water, the temperature of your water,

and the food soil load inside the dishwasher. Contact your

water company to get information about the hardness

of the water in your area. Water hardness is measured in

grains per gallon. Use this information and the table above

to determine the amount of detergent to use. You may

purchase a hard water test strip from Haier Appliances.

Call 877-337-3639 and ask for part number WD01X10295.

In Canada, call 800-661-1616.

Use the table as a starting point and then adjust the

amount of detergent you use. Use just enough to get

good wash performance. Using just the right amount of

detergent will provide great wash performance without

wasting detergent or etching glassware.

Using too much detergent with very soft and/or very

hot water may cause a condition called etching on your

glassware. Etching is a permanent cloudiness in your

glassware. This condition is irreversible. However, using too

little detergent will cause poor wash performance.

DO NOT USE HAND DISH DETERGENT

NOTE: Using a detergent that is not specifically designed for

dishwashers will cause the dishwasher to fill with suds. During

operation, these suds will spill out of the dishwasher vents,

covering the kitchen floor and making the floor wet.

Because so many detergent containers look alike, store the

dishwasher detergent in a separate space from all other

cleaners. Show anyone who may use the dishwasher the

correct detergent and where it is stored.

While there will be no lasting damage to the dishwasher,

your dishes will not get clean using a dishwashing detergent

that is not formulated for automatic dishwashers.

Number of

Grains/Gal.

Detergent Cup(s) to Fill

Less than 5 Fill main cup to line 20

5 to 10 Fill main cup to line 30

Greater than 10

Fill both main cup

and pre-wash cup

Pre-Wash

Rinse

Agent

Main Wash

Detergent

Dispenser

8 49-55125-1

ENGLISH

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

UPPER RACK

The upper rack is for glasses, cups, and saucers. This is also

a secure place for dishwasher-safe plastic items. The upper

rack can be used for odd sized utensils. Sauce pans, mixing

bowls, and other similarly shaped items should be placed face

down for best wash performance.

The cup shelf may be placed in the up or down position to add

flexibility.

IMPORTANT: Ensure that items do not protrude through the

bottom of the rack where they will block the rotation of the

upper spray arm. This could result in noise during operation

and/or poor wash performance.

UPPER RACK - ADJUSTMENT

The upper rack may be adjusted to

accommodate larger

items.

To adjust the upper rack:

Fully extend the upper rack and rotate open the two plastic

end caps

on the front of the rails.

Remove the upper rack.

Select the set of rollers on the side of the rack that

provides the desired height, and reinstall the upper rack by

guiding the rack rails between the appropriate set of

rollers.

With the rack reinstalled, rotate closed the two plastic end

caps, ensuring

the snap is properly engaged. Failure to

properly engage the

end caps may result in the rack falling

from the dishwasher.

A loaded upper rack may be heavier

than anticipated. To prevent minor

injury or damage to the contents, do not raise or lower the

upper rack after the rack is loaded.

CAUTION

End Cap

Rollers

Rail

Remove:

Rail

End

Cap

Replace:

Rollers

USING THE DISHWASHER

49-55125-1 9

ENGLISH

USING THE DISHWASHER

For best dishwashing results, follow these loading guidelines. Features and appearance of racks and silverware baskets

may vary from your model.

LOWER RACK

When loading the lower rack, do not load large platters or

trays in the front left. They may prevent detergent from

circulating during the wash cycle.

The lower rack is best used for plates, saucers and cookware. Large

items should go along the sides. Load platters, pots

and bowls

along the sides, in corners or in the back. The

soiled side of

items should face the center of the rack.

IMPORTANT: Ensure that items do not protrude through the

bottom of the rack or the silverware basket where they will

block the rotation of the lower spray arm. This could result in

noise during operation and/or poor wash performance.

SILVERWARE BASKET

The silverware basket may be used without the topper for

quick loading. With the topper, flatware is better positioned

for the dishwasher to thoroughly wash and dry all pieces by

preventing nesting.

Without the topper

Put the flatware in the removable basket with fork and knife

handles up to protect your hands. Place spoons in the basket

with handles down. Mix knives, forks and spoons so they

don’t nest together. Distribute evenly. Small plastic items,

such as measuring spoons and lids from small containers,

should go in the bottom of the silverware basket with

silverware on top.

With the topper

Place small plastic items, such as measuring spoons and lids

from small containers, in the bottom of the basket and snap

the topper in place. Insert spoons and forks, handles first,

through the holes in the topper. Place knives, blades first,

through the holes in the topper.

IMPORTANT:

Do not load large or tall utensils where they

may block the detergent dispenser or upper spray arm. This

could result in noise during operation and/or poor wash

performance.

10 49-55125-1

ENGLISH

CARE AND CLEANING

CONTROL PANEL

To clean the control panel, use a lightly dampened cloth.

Then dry thoroughly.

EXTERIOR DOOR PANEL

Before cleaning the front panel, make sure you know what type

of panel you have. Refer to the last two letters of your model

number. You can locate your model number on the left-hand tub wall

just inside the door. If your model number ends with BB or WW then

you have a painted door panel. If your model number

ends with SS,

then you have a Stainless Steel door panel.

Follow the instructions below for cleaning the door panel for

your specific model.

Painted Door Panel (model numbers ending in BB–black

or WW–white)

Use a clean, soft, lightly dampened cloth, then dry thoroughly

Do not use scouring pads or powered cleaners because these

products can scratch the finish.

Stainless Steel Door Panel (model numbers ending in SS)

For cleaning rust and tarnish, cleaners with oxalic acid such

as Bar Keepers Friend Soft Cleanser™ will remove rust,

tarnish and small blemishes. Use only a liquid cleanser free

of grit and rub in the direction of the brush lines with a damp

soft sponge. Do not use appliance wax or polish on the

stainless steel.

For other blemishes and marks, use Stainless Steel Magic or

a similar product using a clean soft cloth. Do not use appliance

wax, polish, bleach or products containing chlorine on Stainless

Steel. You can order Stainless Steel Magic # WX10X29 through

Haier Appliances Parts by calling 877-337-3639. In Canada, call

800-661-1616.

DISHWASHER INTERIOR

To clean and de-odorize your dishwasher, use citric acid or

Finish

Dishwasher Cleaner, a detergent additive. Finish

Dishwasher Cleaner will break up mineral deposits, and

remove hard water film and stains.

You can order citric acid Haier Appliances kit #WD35X151

through Haier Appliances Parts by calling 877-337-3639 or

visiting haierappliances.com. In Canada, call 800-661-1616.

You can purchase Finish

Dishwasher Cleaner at your local

grocery store.

UPPER SPRAY HEAD

Do NOT remove the upper spray head.

Clean with warm soapy water using a small plastic bristle

brush.

SPRAY ARMS

Because hard water chemicals will clog the spray arm jets and

bearings, it is necessary to clean the spray arms regularly.

Wash the arms in soapy, warm water and use a soft brush to

clean the jets. Replace them after rinsing thoroughly.

To remove the upper spray arm, twist the retaining nut 45°

and pull the spray arm off the water supply tube.

IMPORTANT: When replacing make sure to twist lock the

retaining nut securely onto the water supply tube. Check that

the spray arm is secure and that it rotates freely.

To remove the lower spray arm, remove the lower rack and

lift spray arm out.

IMPORTANT: When replacing make sure to seat the arm clips

over the retaining ring. Check that the spray arm is secure

and that it rotates freely.

Retaining nut

Upper

Rack

Water Supply Tube

Upper Spray Arm

Lower Spray Arm

Arm

Clips

Retaining

Ring

49-55125-1 11

ENGLISH

CARE AND CLEANING

FILTER ASSEMBLY

Inspect and clean the filters periodically. This should be

done every month or more depending on usage. If there is

a decrease in wash performance or dishes feel gritty, this is

also an indication the filters need to be cleaned.

To clean the filter assembly, remove the bottom rack and

lower spray arm. Twist the filter assembly counterclockwise

and lift to remove. Remove the filter plate.

Rinse the filters with warm soapy water. Scouring pads or

brushes can scratch the filter surfaces but a soft brush or

sponge may be needed to remove stubborn soils or calcium

deposits caused by hard water.

Once cleaned, replace the filter plate, insert the filter assembly

through the plate and twist it clockwise until it locks in place.

Make sure the filters are fully seated as improper replacement

of the filters may reduce the performance level of the

appliance. Replace the lower spray arm and lower rack.

STAINLESS STEEL INNER DOOR

AND TUB

The stainless steel used to make the dishwasher tub and

inner door provides the highest reliability available in a Haier

Appliances dishwasher.

If the dishwasher tub or inner door should be scratched

or dented during normal use, they will not rust or corrode.

These surface blemishes will not affect their function or

durability.

PROTECT AGAINST FREEZING

If your dishwasher is left in an unheated place during the winter,

ask a service technician to:

Turn off electrical power to the dishwasher. Remove fuses or

trip circuit breaker.

Turn off the water supply and disconnect the water inlet line

from the water valve.

Drain water from the water inlet line and water valve. (Use a

pan to catch the water.)

Reconnect the water inlet line to the water valve.

DOES YOUR DISHWASHER HAVE AN

AIR GAP?

An air gap protects your dishwasher against water backing

up into it if a drain clogs. The air gap is not a part of the

dishwasher. It is not covered by your warranty. Not all plumbing

codes require air gaps, so you may not have one.

The air gap is easy to clean:

Turn off the dishwasher and lift off the air gap cover.

Remove the plastic cap under the cover and clean with a

toothpick.

Replace the cap and cover when the air gap is clean.

If the dishwasher tub or inner door should be scratched or

dented during normal use, they will not rust or corrode.

These surface blemishes will not affect their function or

durability.

Press tabs on

the fine filter

and pull to

separate from

the coarse filter

Fine Filter

Coarse Filter

Twist

counterclockwise

and lift to remove

Filter Plate

Replace the filter plate.

Snap the fine filter back

into the coarse filter.

Place filter assembly

through the filter plate

and twist clockwise to

lock into the dishwasher

IMPORTANT: Before replacing,

make sure no objects have

fallen into the opening in the

bottom of the dishwasher.

Filter Plate

Filter Assembly

Lower Spray Arm

Check the air gap any time your dishwasher isn’t draining well.

Air gap

12 49-55125-1

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Start status indicator

light flashing

The door was opened or the

cycle was interrupted.

Press the Start pad once and close the door within 4 seconds

to start the dishwasher. Press the Start pad a second time

when the dishwasher is running only if you wish to cancel the

cycle.

Dishwasher BEEPS

once every minute

This is a reminder that your

dishwasher door has been left

open during operation. It will

continue beeping until you

press Start and close the door.

Press Start and close the door.

Beeping at the end of

the cycle

This is normal. Dishwasher

will beep at end of cycle.

The dishwasher will beep (unless interupted) and the Clean light

will display at the end of the wash cycle.

Dishes and flatware

not clean

Filter assembly is clogged See the CARE AND CLEANING section.

Low inlet water temperature Make sure inlet water temperature is correct (see the USING

THE DISHWASHER section). Turn on the hot water faucet

nearest the dishwasher, let run until the water temperature stops

rising. Then start the dishwasher and turn off the faucet. This

ensures the entering water is hot. Select Wash Temp - Boost.

Water pressure is temporarily

low

Turn on a faucet. Is water coming out more slowly than usual? If so,

wait until pressure is normal before using your dishwasher.

Normal

water pressure to the dishwasher should be 20-120 psi.

Air gap or disposer clogged Clean the air gap or flush the disposer.

High drain loop or air gap not

installed

Refer to the Installation Instructions for proper drain line

installation.

Improper rack loading Make sure large dishware or utensils do not block the detergent

dispenser or the wash arms. See the Loading section.

Poor performing detergent Use a highly rated detergent such as Finish

Quantum

Automatic Dishwashing Detergent.

Spots and filming on

glasses and flatware

Extremely hard water Use rinse agents such as Finish

Jet-Dry

Rinse Aid to prevent

spots and prevent new film build-up.

If water is extremely hard, a softener may be required.

Low inlet water temperature Make sure inlet water temperature is at least 120°F (49°C).

Overloading or improper

loading of the dishwasher

Load dishwasher as shown in the Loading section.

Old or damp powder

detergent

Make sure detergent is fresh. Use a highly rated detergent such

as Finish

Quantum

Automatic Dishwashing Detergent.

Rinse agent dispenser empty

Refill with rinse agent such as Finish

Jet-Dry

Rinse Aid.

Too little or low performing

detergent

Make sure you use the proper amount of highly rated

detergent.

Cloudiness on

glassware

Combination of soft water

and too much detergent

This is called etching and is permanent. To prevent this from

happening, use less detergent if you have soft water. Wash

glassware in the shortest cycle that will get it clean.

Low performing phosphate-

free detergent

See A white film on glassware, dishware and the interior in

this TROUBLESHOOTING TIPS section.

Water temperature entering

the dishwasher exceeds 150°F

(66°C)

This could be etching. Lower the water heater temperature.

Suds in the tub Wrong detergent Use only automatic dishwasher detergents to avoid sudsing.

Finish

Quantum

Automatic Dishwashing Detergent has

been approved

for use in all Haier Appliances dishwashers.

Rinse agent was spilled Always wipe up rinse agent spills immediately.

49-55125-1 13

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Detergent left in

dispenser cups

Dishes or utensils are

blocking the detergent cup

Reposition the dishes, so the water from the lower spray arm

can flush the detergent cup. See the Loading section.

Reposition the tall utensils or heavy silverware that may be

keeping the dispenser cup door from opening. See the Loading

section.

Black or gray marks

on dishes

Aluminum utensils have

rubbed against dishes

Remove marks with a mild, abrasive cleaner.

Dishes don’t dry Door not opened immediately

after Clean light came on

For proper drying, the dishwasher door must be opened

immediately after the Clean light comes on.

Low inlet water temperature Make sure inlet water temperature is at least 120°F.

Use Wash Temp Boost.

Select a higher cycle, such as Heavy.

Rinse agent dispenser is

empty

Check the rinse agent dispenser and fill as required.

Control panel

responded to inputs

but dishwasher never

filled with water

Door may not be completely

closed

Make sure the door is firmly closed.

Water valve may be turned off Make sure water valve (usually located under the sink) is turned

on.

Stained tub interior An overall yellow or brown

film can be caused by iron

deposits in water

A special filter in the water supply line is the only way to correct

this problem. Contact a water softener company.

White film on inside surface—

hard water minerals

We recommend

Finish

Jet-Dry

Rinse Aid

to help prevent hard

water mineral deposits from forming.

Run dishwasher with citric acid to remove mineral deposits.

Citric acid (Part number: WD35X151) can be ordered

through Haier Appliances Parts. See back cover for ordering

information. Alternatively, purchase Finish

Dishwasher

Cleaner and follow the directions on the label.

Dishwasher won’t run Fuse is blown or circuit

breaker is tripped

Replace fuse or reset circuit breaker. Remove any other

appliances from the circuit.

Power is turned off In some installations, the power to the dishwasher is provided

through a wall switch, often located next to the disposer

switch. Make sure it is on.

Control panel is locked Unlock control panel. See the Getting started section.

Reboot your control Turn off power to the dishwasher (at circuit breaker or wall

switch) for 30 seconds, then turn back on.

Control panel lights

go off when you’re

setting controls

Time too long between

touching of selected pads

Each pad must be touched within 30 seconds of the others. To

relight, touch any pad again or open the door and unlock.

Water standing in the

bottom of the tub

Air gap is clogged Clean the air gap. See the CARE AND CLEANING section.

High drain loop or air gap not

installed

Refer to the Installation Instructions for proper drain line

installation.

Water won’t pump

out of the tub

Drain is clogged If you have an air gap, clean it. See the CARE AND CLEANING

section.

If the dishwasher drains into a disposer, run disposer clear.

Check to see if your kitchen sink is draining well. If not, you may

need a plumber.

14 49-55125-1

ENGLISH

TROUBLESHOOTING TIPS

Problem Possible Cause What To Do

Sanitized light does

not illuminate at the

end of the cycle

The door was opened and the

cycle was interrupted during

final rinse

Do not interrupt the cycle by opening the door during the wash

cycle.

The incoming water

temperature was too low

Raise the water heater temperature to between 120°F and

150°F.

Noise Normal operating sounds:

Beeping at the end of the

cycle

Detergent cup opening

Water entering dishwasher

Motor stops and starts at

various times during cycle

Spray arms start and stop at

various times

Drain pump sounds during

pump out

Drain pump starts and stops

several times during each

drain

These are all normal. No action is required.

Rattling dishes when the

spray arm rotates

Make sure dishes are properly loaded. See the Loading section.

Rattling silverware against

door during wash

Tall utensils may be placed in the upper rack to avoid bumping

against inner door during wash cycle.

A white film on

glassware, dishware

and the interior

This problem is likely caused

by a low quality phosphate-

free dishwasher detergent

To remove the white film, run your dishes through a dishwasher

cycle with citric acid. Use a WD35X151 citric acid kit found

online. Otherwise, use Finish

Dishwasher Cleaner found at

your local grocery store.

Pour the citric acid in the detergent cup and close the cover.

Place the filmed but otherwise clean glassware and dishware in

the dishwasher. Leave silverware and other metal items out of

the dishwasher. Turn the dishwasher on and let it run through a

complete cycle without detergent. The glassware, dishware, and

dishwasher should come out film free. Alternatively, a vinegar rinse

may be used. Pour 1 cup of vinegar into dishwasher just after the

detergent cup opens and let the dishwasher complete its cycle.

This may be repeated several times a year as needed.

The use of a rinse agent such as

Finish

Jet-Dry

Rinse Aid

may help minimize a repeat build up of film. Also, the use of a

highly rated detergent such as Finish

Quantum

Automatic

Dishwashing Detergent will help prevent film build-up.

Open the door to interrupt the cycle. Pull the door handle

to release the door.

Do not open the door all the way until the water spray

action stops. Steam may rise out of the dishwasher.

Add additional items.

Press Start and close the door within 4 seconds to

resume the cycle.

FORGET TO ADD A DISH?

Additional items may be added to the dishwasher at any time, ideally items would be added shortly after starting a wash cycle.

49-55125-1 15

ENGLISH

LIMITED WARRANTY

haierappliances.com

All warranty service is provided by our Factory Service Centers, or an authorized Customer Care

technician. To schedule

service online, visit us at haierappliances.com, or call Haier Appliances at 877-337-3639.

In Canada, call 877-470-9174.

Please have your serial number and

your model number available when calling for service.

Servicing your appliance may require the use of the onboard data port for diagnostics. This gives a Haier Appliances factory

service technician the ability to quickly diagnose any issues with your appliance and helps Haier Appliances improve its

products by providing Haier Appliances with information on your appliance. If you do not want your appliance data to be sent

to Haier Appliances, please advise your technician not to submit the data to Haier Appliances at the time of service.

What Haier Appliances will not cover (for customers in the United States):

ʄ Service trips to your home to teach you how to use the

product.

ʄ Improper installation, delivery, or maintenance.

ʄ Failure of the product if it is abused, misused or used for

other than the intended purpose or used commercially.

ʄ Replacement of house fuses or resetting of circuit

breakers.

ʄ Product not accessible to provide required service.

ʄ Damage to the product caused by accident, fire, floods,

or acts of God.

ʄ Incidental or consequential damage caused by possible

defects with this appliance.

ʄ Cleaning or servicing of the air gap device in drain line.

ʄ Damage caused after delivery including damage from

items dropped on the door.

For the period of Haier Appliances will replace

One year

From date of the

original purchase

Any part of the dishwasher which fails due to a defect in materials or workmanship. During this

limited one-year warranty, Haier Appliances will provide, free of charge, all labor and in-home

service to replace the defective part.

Staple your receipt here. Proof of the original purchase

date is needed to obtain service under the warranty.

What Haier Appliances will not cover (for customers in Canada):

ʄ Service trips to your home to teach you how to use the

product.

ʄ Improper installation.

If you have an installation problem, contact your dealer or

installer. You

are responsible for providing adequate

electrical,

exhausting and other connecting facilities.

ʄ Failure of the product if it is abused, misused or used for

other than the intended purpose or used commercially.

ʄ Replacement of house fuses or resetting of circuit

breakers.

ʄ Damage to the product caused by accident, fire, floods,

or acts of God.

ʄ Damage caused after delivery including damage from

items dropped on the door.

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased for home use

within the USA. If the product is located in an area where service by a Haier Appliances Authorized Servicer is not available, you

may be responsible for a trip charge or you may be required to bring the product to an Authorized Haier Appliances Service

location for service. In Alaska, the limited warranty excludes the cost of shipping or service calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty gives

you specific legal rights, and you may also have other rights which vary from state to state. To know what your legal rights

are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: Haier Appliances, Louisville, KY 40225

This limited warranty is extended to the original purchaser and any succeeding owner for products purchased in Canada for home use

within Canada. In home warranty service will be provided in areas where it is available and deemed reasonable by Mabe to provide.

Warrantor: MC Commercial Inc., Burlington, ON, L7R 5B6

WARRANTOR IS NOT RESPONSIBLE FOR CONSE QUEN TIAL DAMAGES.

EXCLUSION OF IMPLIED WARRANTIES

Your sole and exclusive remedy is product repair as provided in this Limited Warranty. Any implied warranties, including

the implied warranties of merchantability or fitness for a particular purpose, are limited to one year or the shortest

period allowed by law.

16 49-55125-1

ENGLISH

Haier Appliances Website

Have a question or need assistance with your appliance? Try the Haier Appliances Website 24 hours a day, any day of the year!

You can also shop for more great Haier Appliances products and take advantage of all our on-line support services designed

for your convenience. In the US: haierappliances.com

Register your new appliance on-line at your convenience! Timely product registration will allow for enhanced communication

and prompt service under the terms of your warranty, should the need arise. You may also mail in the pre-printed registration

card included in the packing material. In the US: haierappliances.com

In Canada: 877-470-9174.

Schedule Service

Expert Haier Appliances repair service is only one step away from your door. Get on-line and schedule your service at your

convenience any day of the year. In the US: haierappliances.com or call 877-337-3639 during normal business hours.

In Canada: 877-470-9174.

CONSUMER SUPPORT

Printed in China

Parts and Accessories

Individuals qualified to service their own appliances can have parts or accessories sent directly to their homes (VISA, MasterCard

and Discover cards are accepted).

In the US: 877-337-3639 during normal business hours.

In Canada: 800-661-1616.

Instructions contained in this manual cover procedures to be performed by any user. Other servicing generally should be

referred to qualified service personnel. Caution must be exercised, since improper servicing may cause unsafe operation.

If you are not satisfied with the service you receive from Haier Appliances, contact us on our website at haierappliances.com

with all the details including your phone number, or write to:

In the US: Haier Appliances, Consumer Relations | PO Box 1780 | Rapid City, SD 57709

In Canada: 877-470-9174.

Remote Connectivity

For assistance with wireless network connectivity (for models with remote enable), visit our website in the US at haierappliances.com

Manuel d’utilisation

QDT125 Séries

Lave-Vaisselle Incorpere 18”

49-55125-1 05-18 GEA

2 49-55125-1

FRANÇAIS

DOCUMENTS À CONSERVER

Merci d’avoir acheté ce produit Haier. Ce manuel d’utilisation

vous aidera à obtenir la meilleure performance possible de

votre nouveau lave-vaisselle.

Pour référence ultérieure, inscrire le numéro de plaque

signalétique et la date d’achat. La plaque signalétique est

située sur la paroi de la cuve, à l’intérieur de la porte.

Pour faciliter l’obtention d’un service sous garantie, agrafer la

preuve de la date d’achat à ce manuel.

____________________________________________________

N° de modèle

____________________________________________________

N° de série

____________________________________________________

Date d’achat

TABLE DES MATIÈRES

CONSIGNES DE SÉCURITÉ .........................................................................................3

UTILISATION DU LAVE-VAISSELLE .................................................................................5

Comment démarrer .................................................................................................... 5

Distributeurs .......................................................................................................... 6

Chargement ........................................................................................................... 8

ENTRETIEN ET NETTOYAGE ......................................................................................10

CONSEILS DE DÉPANNAGE .......................................................................................12

GARANTIE LIMITÉE .............................................................................................. 15

SERVICE À LA CLIENTÈLE ........................................................................................ 16

49-55125-1 3

FRANÇAIS

CONSIGNES DE SÉCURITÉ

CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE TOUTES LES CONSIGNES AVANT D’UTILISER L’APPAREIL

FRANÇAIS

AVERTISSEMENT

Pour votre sécurité, veuillez suivre les directives données dans le présent

manuel afin de réduire au minimum les risques d’incendie, d’explosion et de chocs électriques et

prévenir tout dommage et blessure grave ou mortelle.

AVERTISSEMENT

INSTALLATION ET ENTRETIEN APPROPRIÉS

Ce lave-vaisselle doit être correctement installé, en conformité avec les directives d’installation fournies, avant d’être

utilisé. Si vous n’avez pas reçu les directives d’installation avec votre appareil, vous pouvez vous les procurer en visitant

notre site web à l’adresse haierappliances.com.

ʄCet appareil doit être relié à un système de câblage

électrique permanent en métal, mis à la terre. Sinon, un

fil de mise à la terre pour appareillage doit être installé

et raccordé à la borne ou au fil de mise à la terre de

l’appareil.

ʄUn raccordement incorrect du fil de mise à la terre

peut présenter un risque d’électrocution. Consultez un

électricien ou un technicien qualifié si vous n’êtes pas

certain que l’appareil est correctement mis à la terre.

ʄVeuillez vous débarrasser de la façon appropriée de vos

vieux électroménagers et des matériaux d’emballage ou

d’expédition.

ʄNe tentez pas de réparer ou de remplacer une pièce

quelconque de votre lave-vaisselle, à moins que cela

ne soit spécifiquement recommandé dans le présent

manuel. Confiez toutes les autres réparations à un

technicien qualifié.

ʄUtilisez uniquement un nécessaire de cordon électrique

WX09X70910 ou câblez directement sur le circuit

électrique du domicile. L’omission d’observer cette

instruction peut causer un risque d’incendie ou de blessure.

ʄPour réduire au minimum les risques d’électrocution,

débranchez l’appareil de sa source d’alimentation avant

d’en effectuer l’entretien.

REMARQUE : Le fait d’arrêter le lave-vaisselle ne

coupe l’alimentation électrique de l’appareil. Nous

vous recommandons de confier la réparation de votre

électroménager à un technicien qualifié.

AVERTISSEMENT

LORS DU FONCTIONNEMENT DE VOTRE LAVE-VAISSELLE, PRENEZ LES

PRÉCAUTIONS DE BASE, NOTAMMENT LES SUIVANTES

ʄN’utilisez cet appareil que pour l’usage pour lequel il a été

conçu, comme expliqué dans le présent manuel.

ʄUtilisez uniquement un détergent ou un agent mouillant

recommandés pour utilisation dans un lave-vaisselle

et tenez-les à l’écart des enfants. L’utilisation d’un

détergent non conçu pour les lave-vaisselles peut

provoquer la formation de mousse.

ʄPlacez les articles coupants de manière à ce qu’ils

n’endommagent pas le joint d’étanchéité de la porte.

ʄPlacez dans le panie r à couverts les couteaux tranchants le

manche vers le haut afin de réduire les risques de coupures.

ʄNe lavez pas les articles en plastique à moins qu’ils

ne portent la mention « Lavable au lave-vaisselle » ou

l’équivalent. Si certains articles en plastique ne portent

pas cette mention, reportez-vous aux recommandations

du fabricant.

ʄNe faite pas fonctionner le lave-vaisselle si tous les panneaux

de la carrosserie n’ont pas été correctement réinstallés.

ʄNe modifiez pas le fonctionnement des commandes.

ʄAbstenez-vous de vous asseoir, de vous accrocher ou de

vous tenir sur la porte ou le panier du lave-vaisselle, ou

d’en faire un emploi abusif de toute autre manière.

ʄPour réduire le risque de blessure, ne laissez pas les

enfants jouer avec l’électroménager, grimper dessus ou

s’y introduire.

ʄNe rangez ni n’utilisez des matières combustibles, y

compris de l’essence ou d’autres liquides ou vapeurs

inflammables, à proximité de cet appareil ou de tout autre.

ʄLes petites pièces représentent un risque d’étouffement

pour les jeunes enfants si elles sont retirées du lave-

vaisselle. Gardez-les à l’écart des jeunes enfants.

LIRE ET

CONSERVEZ CES DIRECTIVES

4 49-55125-1

FRANÇAIS

CONSIGNES DE SÉCURITÉ

SÉCURITÉ DU CHAUFFE-EAU

Dans certaines conditions, il peut se former de l’hydrogène dans un chauffe-eau qui n’a pas été utilisé pendant deux semaines ou plus.

L’HYDROGÈNE EST UN GAZ EXPLOSIF.

Si vous n’avez pas utilisé votre chauffe-eau pendant deux semaines ou plus, ouvrez tous les robinets d’eau chaude et laissez

couler l’eau pendant plusieurs minutes afin de réduire les risques de dommages matériels ou de blessures. Prenez cette

précaution avant même d’utiliser un électroménager raccordé au chauffe-eau pour éliminer l’hydrogène qui pourrait s’y

être accumuléé. Puisqu’il s’agit d’un gaz inflammable, ne fumez pas ou n’utilisez pas une flamme nue ou un électroménager

au cours de ce processus.

POUR ÉVITER LES BLESSURES MINEURES OU LES DOMMAGES MATÉRIELS

ʄPendant ou après le cycle de lavage, le contenu peut

s’avérer très chaud au toucher. Manipulez-le avec soin.

ʄUne surveillance attentive est nécessaire lorsque cet

appareil est utilisé par ou près des enfants. Ne laissez pas

les enfants jouer à proximité du lave-vaisselle lorsque vous

la fermeture de la porte, la fermeture de la crémaillère

supérieure, ou tout réglage en hauteur du panier supérieur

afin d’éviter que leurs petits doigts se coincent.

ʄArticles autres que la vaisselle : ne lavez pas dans le lave-

vaisselle des articles comme des filtres de purificateur

d’air, des filtres de systèmes de chauffage ou des

pinceaux. Vous pourriez endommager le lave-vaisselle et

provoquer une décoloration ou des taches dans l’appareil.

RISQUE DE SUFFOCATION POUR UN ENFANT COINCÉ À L’INT RIEUR

DE L’APPAREIL

ÉLIMINATION APPROPRIÉE DU LAVE-VAISSELLE

Les lave-vaisselle jetés ou abandonnés sont dangereux… même si vous ne les laissez

là que pour quelques jours. Si vous voulez jeter votre lave-vaisselle, veuillez suivre les

directives ci-dessous pour éviter les accidents.

ʄNe laissez pas les enfants jouer avec, sur, le lave-vaisselle, ou à l’intérieur de celui-ci ou

de tout autre électroménager mis aux rebuts.

ʄEnlevez la porte du compartiment de lavage ou enlevez le verrou en ou enlevez le

verrou en dégageant les deux languettes de retenue à l’aide d’un tournevis à lame

plate (comme illustré).

EXIGENCES ÉLECTRIQUES

ʄCet appareil électroménager doit être alimenté par

du courant de 120V, 60 Hz, et branchéà un circuit de

dérivation bien mis à la terre, protégé par un fusible à

retardement ou un disjoncteur de 15 ou 20 ampéres.

ʄSi l’alimentation électrique fournie ne remplit pas les

caractéristiques ci-dessus, nous vousrecommandons de faire

installer par un électricien qualifié une bonne prise.

ʄLe circuit de votre lave-vaisselle ne doit être utilisépar aucun

autre appareil électroménager quandle lave-vaisselle fonctionne,

car le lave-vaissellenécessite toute la capacité du circuit.

ʄSi votre lave-vaisselle est branché sur un circuit relié à

un interrupteur mural, assurez-vous d’actionner celui-ci

avant d’utiliser votre appareil.

ʄSi vous fermez l’interrupteur mural entre les cycles de

lavage, attendez de 5 à 10 secondes après avoir ramené

l’interrupteur à marche avant d’appuyer sur la touche

Start (Marche) pour permettre aux commandes de se

réinitialiser.

ʄN’utilisez que les détergents et agents de rinçage liquides,

en poudre ou en tablette ou les Finish

Quantum

Automatic Dishwashing Detergent recommandés

pour les lave-vaisselle et gardez-les hors de la portée

des enfants. Les détergents pour lave-vaisselle Finish

Quantum

Automatic Dishwashing Detergent et les

agents de rinçage Finish

Jet-Dry

Rinse Aid sont

approuvés avec les lave-vaisselle Haier Appliances.

LIRE ET

CONSERVEZ CES DIRECTIVES

AVIS

Dégager

les deux

languettes

de retenue

CONSIGNES DE SÉCURITÉ IMPORTANTES

LIRE TOUTES LES CONSIGNES AVANT D’UTILISER L’APPAREIL

AVERTISSEMENT

ATTENTION

La page charge ...

Haier QDT125 Series Le manuel du propriétaire

Marque: Haier

Modèle: QDT125 Series

Catégorie: Lave-vaisselle

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Haier QDT125 Series Owner's manual
español: Haier QDT125 Series El manual del propietario

Haier QDT125 Series Le manuel du propriétaire

Haier QDT125 Series Le manuel du propriétaire

dans d''autres langues

Autres documents