GE ZIF360NHCLH Guide d'installation

Marque: GE

Modèle: ZIF360NHCLH

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

36” Built-In All-Refrigerators

and All-Freezers

Design Guide

With Installation Instructions

Installation

Instructions

monogram.com

31-49140-1

10-17 GEA

31-49140-1

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

•

IMPORTANT – Save these instructions for

local inspector’s use. Observe all governing codes and

ordinances.

•

Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

If you received a damaged unit, you should immediately

contact your dealer or builder.

Skill Level – Installation of this unit requires basic

mechanical, carpentry and plumbing skills. Proper

installation is the responsibility of the installer. Product

failure due to improper installation is not covered under

the Monogram Warranty. See the Owner’s Manual for

warranty information.

For Monogram local service in your area, call 1.800.444.1845 or visit monogram.com.

For Monogram service in Canada, call 1.800.561.3344

For Monogram Parts and Accessories, call 1.800.444.1845 or visit monogram.com.

WARNING

Tip Over Hazard.

These appliances are top heavy, especially with any doors open, and must be secured to prevent tipping

forward which could result in death or serious injury. Read and follow the entire installation instructions for

securing the appliance with the anti-tip system.

WARNING

Explosion Hazard.

Keep flammable materials and vapors, such as gasoline, away from appliance. Failure to do so can result

in fire, explosion, or death.

WARNING

To reduce the risk associated with choking, do not allow children under 3 years of age to

have access to small parts during the installation of this product.

CAUTION

Lifting Hazard

This unit is very heavy. To reduce the risk of person injury during maneuvering and installing this appliance,

3 people are required for proper installation.

CAUTION

Keep fingers out of the “pinch point” areas; clearances between the doors and between the

doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

WARNING

Electrical Shock Hazard.

Plug into a grounded 3-prong outlet.

Do not remove the ground prong.

Do not use an adapter.

Immediately discontinue use of a damaged supply cord.

If the supply cord is damaged it must be replaced by a

qualified service professional with an authorized service

part from the manufacturer.

Do not use an extension cord with this appliance.

Failure to follow these instructions can result in death,

fire, or electrical shock.

Follow the instructions in the section Grounding the unit.

This appliance must be installed with a means in the

fixed house wiring or circuit breaker for disconnecting the

appliance from the electrical supply after installation.

31-49140-1

Consignes de sécurité

AVANT DE COMMENCER

Veuillez lire toutes ces instructions attentivement.

• IMPORTANT – Conservez ces instructions à

l’usage de l’inspecteur local. Observez tous les codes et

décrets en vigueur.

•

Note à l’installateur – Assurez-vous de laisser ces

instructions au consommateur.

•

Note au consommateur - Conservez ces instructions

avec votre manuel d’utilisation pour

consultation ultérieure.

Si vous avez reçu un appareil endommagé, veuillez

communiquer immédiatement avec votre revendeur ou votre

entrepreneur.

Niveau de compétence – L’installation de cet appareil

exige des compétences de base en mécanique, menuiserie

et plomberie. La responsabilité d’une installation adéquate

relève de l’installateur. La garantie Monogram ne couvre

pas les défectuosités du produit causées par une installation

inadéquate. Consultez le manuel d’utilisation pour des

renseignements sur la garantie.

Pour joindre le service Monogram de votre région, composez le 1.800.444.1845 ou visitez monogram.com.

Pour le service Monogram au Canada, composez le 1.800.561.3344.

Pour le service des Pièces et accessoires Monogram, composez le 1.800.444.1845 ou visitez monogram.com.

AVERTISSEMENT

Risque de basculement.

Ces électroménagers sont lourds du haut, notamment lorsqu’une porte est ouverte, de sorte qu’ils doivent être fixés pour prévenir

un basculement vers l’avant susceptible d’occasionner des blessures graves ou la mort. Lisez et observez la totalité des instruc-

tions d’installation pour connaître la façon de fixer l’électroménager sur le dispositif antibasculement.

AVERTISSEMENT

Risque d’explosion.

Gardez les matières et les vapeurs inflammables telles que l’essence à distance de l’électroménager. L’omission de prendre cette

précaution peut entraîner un incendie, une explosion ou la mort.

AVERTISSEMENT

Pour réduire le risque d’étouffement pendant l’installation de ce produit, ne pas laisser les petites pièces

à la portée des enfants âgés de moins de 3 ans.

AVERTISSEMENT

Risque lié à la manipulation d’un objet lourd

Cet appareil est très lourd. Afin de réduire le risque de blessure pendant la manipulation et l’installation de cet électroménager, la

participation de 3 personnes est nécessaire à l’exécution d’une installation correcte.

AVERTISSEMENT

Gardez vos doigts éloignés des points de pincement. Les espaces entre les portes et ceux entre les

portes et l’armoire sont particulièrement restreints. Soyez prudent lorsque vous fermez les portes en présence d’enfants.

AVERTISSEMENT

Risque d’électrocution.

Branchez l’appareil dans une prise à 3 broches mise à la terre.

N’enlevez pas la broche de mise à la terre.

N’utilisez pas un adaptateur.

Cessez immédiatement l’utilisation d’un cordon électrique

endommagé. Si le cordon électrique est endommagé, son rem-

placement doit être exécuté par un technicien en réparation qua-

lifié au moyen d’un cordon de rechange autorisé par le fabricant.

N’utilisez pas un cordon de rallonge avec cet électroménager.

Le non-respect de ces instructions peut occasionner un décès,

un incendie ou un choc électrique

Suivez les instructions de la section Mise à la terre de l’appareil.

Le circuit électrique auquel cet électroménager sera raccordé

doit comporter un disjoncteur ou un autre dispositif permettant

de couper l’alimentation électrique à l’appareil après l’installation.

31-49140-1

Contents

Safety 2

Instructions for Standard Installation 5

Planning Guide

The Installation Space 6

Dimensions and Clearances 6

Customization Basics 8

Refrigerator Location 8

1/4” Framed Panel Dimensions 9

3/4” Overlay Panel Dimensions 9

Side Panels 10

ZUG2 Grille Panel Dimensions 10

130° Door Swing 11

Installation Instructions

Tools, Hardware, Materials 12

Grounding the Unit 12

Step 1. Remove Packaging 13

Step 2. Install Water Line 13

Step 3. Install Side Panels 14

Step 4. Anti-Tip Procedures 14

Step 5. Level Unit 17

Step 6, Secure Unit to Wall 17

Step 7. Adjust Door Swing 18

Step 8. Install Grille Panel 18

Step 9. Install Framed Panels 19

Step 9A. Install Overlay Panels 20

Step 10. Connect Water Supply 21

Step 11. Start Icemaker 21

Step 12. Install Toekick 21

Instructions for Flush Installation 22

Planning Guide

The Installation Space 23

Dimensions and Clearances 23

Custom Handle Design Guide 24

1/2” Overlay Panel Dimensions 25

3/4” Decorative Panel Dimensions 26

3/4” Raised Door Panel Routing 27

3/4” Raised Grille Panel Routing 28

3/4” Raised Door Panel Routing

for Unified Installation 29

Side Panels 30

Side Cleats 30

ZUG2 Grille Panel Dimensions 30

Unified Door Panel Dimensions 30

Refrigerator Location 30

Installation Instructions

Tools, Hardware, Materials 31

Grounding the Unit 31

Step 1. Remove Packaging 32

Step 2. Install Water Line 32

Step 3. Install Side Panels 32

Step 4. Install Case Trim 33

Step 5. Anti-Tip Bracket 33

Step 6. Level Unit 35

Step 7. Adjust Door Swing 36

Step 8. Install Grille Panel 36

Step 9. Install overlay Panels 37

Step 10. Connect Water Supply 38

Step 11. Start Icemaker 38

Step 12. Install Toekick 38

Instructions for Stainless Steel Installation 39

Planning Guide

The Installation Space 40

Dimensions and Clearances 40

Customization Basics 42

Refrigerator Location 42

130° Door Swing 43

Installation Instructions

Tools, Hardware, Materials 44

Grounding the Unit 44

Step 1. Remove Packaging 45

Step 2. Install Water Line 45

Step 3. Install Side Panels 45

Step 4. Anti-Tip Bracket 46

Step 5. Level Unit 48

Step 6, Secure Unit to Wall 49

Step 7. Adjust Door Swing 49

Step 8. Connect Water Supply 50

Step 9. Start Icemaker 50

Step 10. Install Toekick 50

Instructions for Standard Installation

31-49140-1

Design Guide - Standard Installation

36" Frame to

Frame Width

*84" From

Floor to

Top Frame

35"

Case Width

*83-1/2"

Rear

25-3/8" Case Depth

Depth Including

Handles 26-7/8"

THE INSTALLATION SPACE

Water And Electrical Locations

Electrical and water supply must be located as

shown.

The Cutout Depth Must Be 24” (60.96 cm)

Minimum

The unit will project forward, slightly beyond adjacent

cabinetry, depending on your installation.

Cutout Depth Beneath a Soffit:

When installed beneath a soffit, the soffit cannot

exceed the 24” (60.96 cm) installation depth shown.

The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is

required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install

a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be

located on rear wall as shown.

• Water line can enter the opening through the floor

or back wall. The water line should be 1/4” O.D.

copper tubing or QuickConnect

™

kit between the

cold water line and water connection location,

long enough to extend to the front of the unit.

Installation of an easily accessible shut-off valve in

the water line is required.

DIMENSIONS AND CLEARANCES

* Shipping height. The

product can be adjusted

to fit into a cutout that

is 84-1/2” (214.63 cm)

max. height. Note that

the top case trim at the

front is 1/2” (1.27 cm)

higher and will overlap

upper cabinetry or soffit.

Use leveling legs and

wheels for a maximum

1” (2.54 cm) height

adjustment.

Product Clearances

These units are equipped with a 3-position door

stop. The factory set 115° door swing can be adjust-

ed to 90° if clearance to adjacent cabinets or walls

is restricted. Order WX14X99 door stop for precise

settings between 90° and 130°.

130° Door Swing

90° Door Swing

4” Minimum

to a Wall

90°

23-7/8”

Case Behind

Frame

36-3/4”

Allow 25” (63.5 cm) minimum clearance for a

full 130° door swing. Allow 15” (38.1cm) for pan

removal.

For a 90° door swing, allow 4” (10.16 cm) minimum

clearance to a wall. If the 90° doorstop position is

used, pan access is maintained but pan removal is

restricted.

See illustration on page 11 to determine door swing

interaction with adjacent cabinets or countertops.

115° Door Swing

31-49140-1

Design Guide - Standard Installation

These units are equipped with a 3-position door stop.

The factory set 115° door swing can be adjusted to

90° or 130° if clearance to adjacent cabinets or walls

is restricted. Order WX14X99 door stop for precise

settings between 90° and 130°.

When Installed into a corner:

Allow 25” (63.5 cm) for a full 130° door swing. Allow

15” (38.1cm) for pan removal. Allow 4” (10.16 cm)

min. clearance when door swing is adjusted to a 90°

opening for pan access, but pan removal is restricted.

25"

Min. to

Wall

130°

130° Door

Swing

CLEARANCES

ZUG2, ZUGSS2 Unified Grille Panel Kit

• If you are installing two units, side by side, the installation

space must be 71-1/2” (181.61 cm) wide.

NOTE: Additional cutout width may be required when side

panels are used. Add side panel thickness to the finished

cutout to calculate rough-in width.

• The water and electrical locations for each product must

be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply is

recommended for each product.

Clearances for Multiple Single Door Installations

In a side-by-side installation of a left and right door

swing product, a 1” (2.54 cm) clearance between

the units is required. Order ZUGSS2 Stainless Steel

Unified Grille Panel Kit or ZUG2 Custom Panel

Unified Grille Panel Kit for one continuous grille

panel.

Clearances for two products installed side-by-

side with the same (left or right) door swing

Allow 2” (5.08 cm) minimum clearance between the

products to prevent door swing interference. Order

the WX14X99 adjustable door stop to reduce the

factory set 115° door swing. Allow 15” (38.1cm)

minimum to a wall to achieve full drawer extension

and pan removal.

NOTE: ZUG2 and ZUGSS2 Grille Panel Kit will NOT

fit this installation.

15"

Clearances for two products installed side-by-

side with right and left side hinges together Allow

5” (12.7 cm) minimum between the two products to

prevent one door from striking the other. Use the

WX14X99 adjustable door stop to reduce the factory

set 115° door swing and to allow pan removal.

NOTE: ZUG2 and ZUGSS2 Grille Panel Kit will NOT

fit this installation.

INSTALLATION

31-49140-1

Design Guide - Standard Installation

CUSTOMIZATION BASICS:

Framed or Overlay Panels, Custom

Handles and Accessory Kits

Trimmed models are designed to be customized with

decorative panels. Field installed custom door and

grille panels are required.

Optional Accessory Kits

• ZKHSS2: Monogram Tubular Stainless Steel

handles designed to fit 3/4” (1.9 cm) overlay panels.

• ZKHPSS1: Pro Tubular Stainless Steel handle

designed to fit 3/4” (1.9 cm) overlay panels.

• ZUG2: For side-by-side installation of two trimmed

models. This kit provides for the installation of a

unified custom grille panel to span the width of two

units using a framed or overlay panel.

REFRIGERATOR LOCATION

• Do not install the refrigerator where the

temperature will go below 55°F (13°C). It

will not run often enough to maintain proper

temperatures.

• Do not install the refrigerator where temperatures

will go above 100°F (37°C). It will not perform

properly.

• Do not install the refrigerator in a location

exposed to water (rain, etc.) or direct sunlight.

• Install it on a floor strong enough to support it

fully loaded.

31-49140-1

Design Guide - Standard Installation

If you choose to install framed panels, they must be cut to the

dimensions shown. The panels will slide into the frame on the door

and grille.

If the custom panel is less than 1/4” (0.63 cm) thick and if it fits

loosely in the door frame, it can be backed up with a piece of filler

material or foam tape to improve the fit.

IMPORTANT NOTE: Maximum weight for door panel is 67 pounds

(30.39 kg). Maximum total weight for assembled grille panel is 11

pounds (4.99 kg).

3/4” (1.9 cm) OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be installed

on trimmed models. The overlay panel must be secured to a 1/4”

(0.63 cm) thick backer panel which slides into the trim. A spacer

panel 0.10” (0.25 cm) thick must be placed between the overlay

and backer panel.

IMPORTANT NOTE: Maximum total weight for assembled door

panel is 67 pounds (30.39 kg). Maximum total weight for assem-

bled grille panel is 11 pounds (4.99 kg).

Assemble the panels with glue and screws.

• Center the spacer panel on the backer panel, left to right and top

to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay panel and

secure with glue and screws. Screws must be countersunk into

the backer panel.

Framed Panel Dimensions

1/4” (0.63 cm)

Framed Panel

A (Width) B (Grille Height) C (Door Height)

33-7/8” (86.04 cm) 8-7/8” (22.54 cm) 69-5/16”(176.05 cm)

Overlay Panel Dimensions

1/4” (0.63 cm)

Backer Panel

A (Width) B (Grille Height) 69-5/16”(176.05 cm)

33-7/8” (86.04 cm) 8-7/8” (22.54 cm) 69-5/16”(176.05 cm)

0.10” (0.25 cm)

Spacer Panel

32-1/2” (82.55 cm) 7-5/8” (20 cm) 67-15/16”

(172.56 cm)

3/4” (1.9 cm)

Overlay Panel

34-1/8” (96.67 cm) 9” (22.86 cm) 69-9/16”

(176.69 cm)

NOTE: Left-to-right offset is not

always equal to top-to-bottom offset.

1/4"

Panel

Door

5/16"

Trim

Reveal

1/4” (0.63 cm) FRAMED PANEL DIMENSIONS

31-49140-1

SIDE PANELS

Side panels must be used whenever the sides of the

unit will be exposed. The 1/4” (0.63 cm) side panels

will slip into the side case trim. Secure the panels to

the unit with stick-on hook and loop fastener strips.

Order the side panels from the cabinet manufacturer.

• Cut a notch in the top front corner as shown to allow

clearance for corner keys in the front side trim.

ZUG2 GRILLE PANEL DIMENSIONS

The ZUG2 unified grille panel kit provides for the

installation of a framed or overlay grille panel.

* Depending on

installation height.

Assemble the overlay panels in the same manner

as the door panel.

IMPORTANT NOTE: The maximum weight for the

unified grill is 25 pounds (11.24 kg).

Design Guide - Standard Installation

*84"

2-9/16"

24"

*3" to 4"

3/16"

1-7/8"

Framed Panel Dimensions

1/4” (0.63 cm)

Framed Panel

A (Width) B (Height)

69-7/8” (177.48 cm) 8-7/8” (22.54 cm)

Overlay Panel Dimensions

1/4” (0.63 cm)

Backer Panel

A (Width) B (Grille Height)

69-7/8” (177.48cm) 8-7/8” (22.54 cm)

0.10” (0.25 cm)

Spacer Panel

68-1/2” (97.79 cm) 7-5/8” (20 cm)

3/4” (1.9 cm)

Overlay Panel

70-1/8” (178.12 cm) 9” (22.86 cm)

31-49140-1

Design Guide - Standard Installation

Top View

130° DOOR SWING

Scale 1:1

Frameless Cabinets: The case trim

overlaps cabinets at the top and sides.

Therefore, frameless cabinets may require

filler strips to prevent interference with cabinet

door swing. The opening must allow for filler

strips.

31-49140-1

Installation Instructions - Standard Installation

HARDWARE SUPPLIED

• Water filter bypass plug

• Anti-Tip brackets

• 3 lag screws

• 2 Hair Pin Cotters

• 4 washers

• 5 toggles with bolts

• Toekick

TOOLS AND MATERIALS REQUIRED

• Tin snips to cut banding

• #2 Phillips screwdriver

• Stepladder

• Drill and 1/2”, 3/16” bits

• Bucket

• 1/4”, 1/2”, 5/16”, 7/16” socket

• Level

• Safety glasses

• Appliance hand truck

• Pliers

• Tubing cutter

• Stud finder

• 7/16” and 1-1/4” open-end wrench

• 1/4” copper water line tubing or SmartConnect

™

Refrigerator Tubing kits

• Water shut-off valve (optional but recommended)

• Custom panels for door and grille panel

• Screws to secure unit to cabinetry

• Stick-on hook and loop fastener strips for

1/4” (0.63 cm) side panels

FLOORING

For proper installation, this product must be placed

on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should

be strong enough to support a fully loaded refrigerator

or freezer, or approximately 1,200 lbs. per unit.

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the

product where you are working.

NOTE: Not recommended for installation on carpeted

flooring.

GROUNDING THE UNIT

WARNING

Electrical Shock Hazard.

Failure to follow these instructions can result in death,

fire, or electrical shock.

The power cord of this appliance is equipped with a

3-prong (grounding) plug which mates with a standard

3-prong (grounding) wall receptacle to minimize the

possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it

replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY

CIRCUMSTANCES, CUT OR

REMOVE THE THIRD (GROUND)

PRONG FROM THE POWER

CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE

REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS

APPLIANCE.

LA TERRE DE L’UNITÉ

AVERTISSEMENT

Risque de choc

électrique.

Le non-respect de ces instructions peut entraîner des

risques d’incendies, des chocs électriques ou la mort.

Le cordon d’alimentation de cet appareil est équipé

d’une fiche à trois broches (pour une mise à la terre)

qui s’adapte à la prise de courant standard à 3 broches

(pour une mise à la terre) pour minimiser les risques de

chocs électriques par cet appareil.

Faites vérifier la prise murale et le circuit électrique par

un électricien qualifié pour s’assurer que le système est

correctement mis à la terre.

Dans le cas d’une prise biphasée, l’installateur a la res-

ponsabilité et l’obligation de la remplacer par une prise

triphasée correctement mise à la terre.

NE COUPEZ PAS OU N’ENLEVEZ

PAS, SOUS AUCUN PRÉTEXTE,

LA TROISIÈME BROCHE DE

MISE À LA TERRE DU CORDON

D’ALIMENTATION.

N’UTILISEZ PAS D’ADAPTATEUR POUR BRANCHER

LE RÉFRIGÉRATEUR À UNE PRISE BIPHASÉE.

N’UTILISEZ PAS DE RALLONGE AVEC CET

APPAREIL.

31-49140-1

Installation Instructions - Standard Installation

STEP 1 REMOVE PACKAGING

WARNING

Tip Over Hazard. Product

is much heavier at the top than at the bottom – be

careful when moving. When using a hand truck, handle

from side only.

AVERTISSEMENT

Risque de

basculement

Le produit est beaucoup plus lourd en haut qu’en bas.

Il faut être prudent lors des déplacements. Si un diable

est utilisé, il faut soulever le réfrigérateur sur le côté

seulement.

• Carefully cut banding at the top and bottom, remove

outer carton.

• Slide out back corner posts (2).

• Slide carton off top of cabinet.

NOTE: IT IS NOT NECESSARY TO LAY CABINET

DOWN

IN ORDER TO REMOVE SKID!

NOTE: DO NOT ATTEMPT TO ROLL UNIT OFF SKID.

STEP 2 INSTALL WATER LINE

WARNING

Connect to potable water supply

only.

AVERTISSEMENT

Raccordez l’appareil à une

alimentation d’eau potable seulement.

• A cold water supply is required for automatic icemaker

and AutoFill pitcher operation. The water pressure must

be between 40 and 120 p.s.i. (275-827 kPa).

• Route 1/4” OD copper or SmartConnect

™

plastic

tubing between house cold water line and the water

connection location.

• Tubing should be long enough to extend to the front of

the unit. Allow enough tubing to accommodate bend

leading into the water line connection.

NOTE: The only Monogram approved plastic tubing is

supplied in the SmartConnect

™

Refrigerator Tubing kits.

Do not use any other plastic water supply line because

the line is under pressure at all times. Other types of

plastic may crack or rupture with age and cause water

damage to your home.

SmartConnect

™

Refrigerator Tubing Kits are available in

the following lengths:

2’ (.6 m) WX08X10002

8’ (2.4 m) WX08X10006

15’ (4.6 m) WX08X10015

25’ (7.6 m) WX08X10025

• The unit is secured to the skid

with 4 slotted tie-down straps.

Remove the four 5/16” bolts

from the base channels in the

tie-downs.

• Unit is shipped with two sets

of toe kicks. One for Flush

Inset (longer) and One for

standard installation (shorter).

Pick proper toe kick for your

installation. Discard other toe

kick.

• Remove toekick, custom handle trim, and wall bracket.

Set aside for final installation.

• Lift the unit off the skid with an appliance dolly. Handle

from the sides.

• Remove the four 7/16” bolts securing the tie-down

brackets to the skid.

NOTE: Commonwealth of Massachusetts Plumbing

Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the line

of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

• Turn on the main water supply and flush debris. Run

about a quart of water through the tubing into a bucket.

Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in many

water supply kits. Before purchasing, make sure a saddle

type valve complies with your local plumbing codes.

31-49140-1

• Place the bottom of the wall bracket with tabs on the

horizontal line. Align the center notch on the bracket

with the center line on the wall.

• The anti-tip wall bracket has a series of holes. Select 2

holes that match with the located studs. Make sure the

holes selected are on the center of the studs. Mark the

wall at these points.

• Mark an additional hole at each end of the bracket. If

one of the studs is closer to the end of the bracket, mark

an additional hole towards the center of the bracket.

• Drill 1/2” (1.27 cm) holes into the wall board at the loca-

tions marked for the toggles to be mounted (not the stud

markings).

• Drill 3/16” (0.47 cm) holes into wooden studs where

marked. If steel stud construction, drill 1/2” (1.27 cm)

holes into the studs where marked. You will use 2 tog-

gles with the metal studs.

Installation Instructions - Standard Installation

WARNING

Tip Over Hazard.

The unit is top-heavy and must be secured to prevent

the possibility of tipping forward.

AVERTISSEMENT

Risque de

basculement

L’appareil ménager est beaucoup plus lourd en haut et

il faut le maintenir en place pour éviter la possibilité de

son basculement vers l’avant.

• The kit supplied with the unit contains 2 lag bolts and 4

toggles with bolts. The wall bracket will be attached to

the wall in 4 places.

• Measure the opening where the unit is to be installed.

Mark the center with a vertical line.

• Measure up 81-1/2” (207.01 cm) from the floor. Mark

this point on the wall.

• Using a level, draw a horizontal line on the wall at this

height.

• Locate at least 2 studs on the back wall. Mark these

points on the horizontal line.

STEP 4 INSTALL ANTI-TIP BRACKET

Two Additional

Hole Locations at

Ends of Brackets

Center

Wall Bracket

Line On Wall

Wall Studs

Line on Wall

Center

STEP 3 INSTALL SIDE PANELS

Skip this step when not using side panels

If you are using 1/4” side panels, they should be insert-

ed into the case trim.

Fasten the panels to the unit with stick-on hook and loop

fastener strips before setting unit in place.

31-49140-1

Install Screws and Bolts:

• Have someone hold the wall bracket centered in place

with each of the holes aligned with the correct opening

in the bracket and level with the horizontal line.

• Insert the lag screws through the bracket and into the

stud. Tighten with a wrench.

•

Insert the bolts into the toggle by hand until snug.

Tighten with a wrench.

Anti-Tip Wall Bracket

Bolt

Wall Toggle

Drywall or

Steel Stud

Install Wall Toggles:

The wall toggles and bolts can be ordered as Service

Kit #WR49X10193. Wall toggles are installed in the

drywall and metal studs for stability. Install the wall tog-

gles as follows:

• Drill 1/2”

(1.27 cm)

holes at the wall markings made in

the holes at the ends of the wall bracket.

• Hold the metal channel flat against the plastic straps

and slide the channel through the hole.

• Gently pull back at the ends of the plastic straps to

make the channel rest flush behind the wall.

• Hold the ends of the straps in one hand and slide the

plastic cap along the straps until the flange of the cap

is flush with the wall.

• Place your thumb between the plastic straps and

bend up and down to snap the straps off at the wall.

Installation Instructions - Standard Installation

Plastic Straps

Metal Channel

Wood Stud

Lag Screw

Anti-Tip Wall Bracket

Cap

STEP 4 INSTALL ANTI-TIP BRACKET (cont.)

31-49140-1

Installation Instructions - Standard Installation

Remove Grilles for Access to Anti-Tip Locking Hooks

Fresh Food Unit

• Open the access door.

• Remove the 4 screws from the grille on the right and 3

screws from the grille on the left.

• Pull the bottom of the grilles forward, down and out to

remove.

Freezer Unit

• Open the access door.

• Remove the 4 screws from the grille on the right and 3

screws from the grille on the left.

• Pull the bottom of the grille forward, down and out to

remove.

Power Cord

Locate the power cord inside the left cavity. If it has not

been adjusted so the plug is easily accessible, do so

now.

Move Unit into Final Position

• Move appliance toward its final installed location. Align

the tabs on the wall bracket with the openings in the

back of the unit.

• The unit has “L” bolts in the upper left and right cor-

ners inside of the access compartment. These bolts

will interlock with the wall bracket and secure the unit

using the washers and hair pin cotters in the hardware

kit once the unit has been leveled and is in the final

position.

STEP 4 INSTALL ANTI-TIP BRACKET (cont.)

Screws Screws

31-49140-1

Installation Instructions - Standard Installation

STEP 5 LEVEL UNIT

All models have 4-point leveling. The front is support-

ed by leveling legs; the rear is supported by adjustable

wheels. Both are accessible from the front of the unit.

• To level the back of the unit, turn the 7/16” hex nut

located above the front wheels. Turn clockwise

to raise or counterclockwise to lower the unit.

• For front leveling, use a 1-1/4” open-end wrench.

• Adjust height of unit to match installation cutout

opening 84-1/2”

(214.63 cm)

. The unit should be

level and plumb with cabinetry.

STEP 6 SECURE UNIT TO WALL

• The “L” rods can be found in the upper left and right

corners of the unit in the access compartment. Look

through the access compartment to make sure the

rods line up with the anti-tip bracket.

• There are 2 washers and a hair pin cotter per rod.

Remove the washers and hair pin cotter from the

end of the rod.

• Rotate and move the “L” rod into the slot in the

anti-tip bracket tab. Once it is in the slot, rotate the

“L” rod so the

hook portion is

pointing down.

The holes at

the front end of

the rod should

be in a vertical

position. Do this

to both sides.

• Pull out on the

end of the rod to

make sure it is secure in the bracket.

• Locate the hole on the rod that is closest to the

unit. A hair pin cotter will be put through this hole

to secure the rod. If this hole appears to be too far

away for a snug fit against the unit, add the washers

one at a time until the pin will fit tightly into the hole.

• Align the straight section of the pin with the hole

from the underside of the rod. Push the pin up

until it snaps into

position. Pliers may

be used. NOTE:

The hair pin cotter

must be vertical

when this step

is completed to

ensure the “L” rod

is engaged in the

bracket.

• Check the rod for

tightness by pulling

forward. If the rod

moves, remove the

hair pin cotter and

place another washer on the rod. Reinsert the pin.

• Replace the grille panel.

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1”

(2.54 cm). If the installation requires more than

84-1/2”

(214.63 cm)

height, the installer should elevate

the unit on a sheet of plywood or runners. Cabinetry

trim could also be added across the top of the

opening to shorten the opening. If you attempt to raise

the unit more than 1” (2.54 cm), you will damage the

front leveling legs and the rear leveling wheels.

“L” Rod

Wall Bracket

“L” Rod

31-49140-1

Installation Instructions - Standard Installation

STEP 7 ADJUST DOOR SWING

NOTE: This appliance has a 3-position door stop.

When space does not allow the door to swing open

fully to 115°, you may change the door swing to a

90° opening. A 130° door swing is available for stan-

dard installation only. Skip this step if door open-

ing is satisfactory for your installation situation.

• Open the hood to view the top hinge. Note the door

stop pin locations. The pin is factory-installed in the

115° position.

• Close the door. Use pliers to unscrew the door stop

and reinstall in the 90 degree or 130 degree position.

Pin Location

for 90°

Door Swing

Pin Location

for 130°

Door Swing

Pin Location

as Shipped

for 115°

Door Swing

STEP 8 INSTALL GRILLE PANEL

• Raise the access panel to the stop position.

• Loosen the screws on the side trim behind the

frame. Remove the bottom trim.

• Slide the panel over the metal baker panel and into

the trim.

• If necessary, tap with a wood block until the panel

slips under the top trim piece.

• Reassemble the bottom trim. Tighten the screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

Installation Instructions - Standard Installation

STEP 9 INSTALL FRAMED PANELS

• There are two sets of holes in the handle side trim.

Replace the handle side trim by installing the original

screws in the FRONT screw holes.

• Secure the handle to the door using the REAR screw

holes.

Use Rear Holes

to Secure Handle

Use Front Holes

to Secure Trim

Right hand models shown. Use the same instruc-

tions for left hand models.

IF YOU ARE INSTALLING OVERLAY PANELS,

GO TO STEP 10A.

Install Door Panel:

• Open the door to 90°. Remove the 6 Phillips head

screws from the door handle.

• Remove the handle. Retain all screws.

• Remove the 6 screws holding the trim, lift off the trim.

Retain the screws.

• Slide the framed panel into the door trim.

Standard supplied handle shown

in 1/4”(0.63 cm) panel position.

Door

Door Trim

Handle

Trim

Installation Instructions - Standard Installation

STEP 9A INSTALL OVERLAY PANELS

• There are two sets of holes in the handle side trim.

Replace the handle side trim by installing the original

screws in the REAR screw holes.

• Secure the handle to the door using the FRONT

screw holes.

Custom Handles

If you are using custom handles, the handle must be

properly secured to the panel before sliding the panel

into the trim.

• The cabinet manufacturer will supply the custom han-

dle and hardware.

• Secure the door trim using new handle side trim.

Discard the supplied handle.

Right hand models shown. Use the same instruc-

tions for left hand models.

Install Door Panel:

• Open the door to 90°. Remove the 6 Phillips head

screws from the door handle.

• Remove the handle. Retain all screws.

• Remove the 6 screws holding the trim, lift off the trim.

Retain the screws.

• Slide the overlay panel into the door trim.

Supplied handle shown

in the overlay panel position.

Door

Door Trim

Handle

Trim

Move

Forward

For 3/4"

Panel

Use Rear Holes

to Secure Trim

Use Front Holes

to Secure Handle

La page charge ...

GE ZIF360NHCLH Guide d'installation

Marque: GE

Modèle: ZIF360NHCLH

Catégorie: Frigos

Taper: Guide d'installation

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: GE ZIF360NHCLH Installation guide

GE ZIF360NHCLH Guide d'installation

Ce manuel convient également à

GE ZIF360NHCLH Guide d'installation

dans d''autres langues

Documents connexes

Autres documents