Samsung RF220NFTAWW/AA Manuel utilisateur

imagine the possibilities

RF22**

English

Refrigerator

user manual

Thank you for purchasing this Samsung product.

DA68-02657A-12.indb 1 2018. 10. 8. 오후 5:45

02_ Safety information

safety information

SAFETY INFORMATION

• Before using your new Samsung Refrigerator,

please read this manual thoroughly to ensure

that you know how to operate the features and

functions that your new appliance oers safely

and eciently.

• This appliance is not intended for use by

persons (including children) with reduced

physical, sensory or mental capabilities, or

lack of experience and knowledge, unless they

have been given supervision or instruction

concerning use of the appliance by a person

responsible for their safety. Children should be

supervised to ensure that they do not play with

the appliance.

• Because the following instructions cover

various models, the characteristics of your

refrigerator may dier slightly from the

refrigerator described in this manual.

• If you have any question, contact us at

1-800-SAMSUNG or ﬁnd help and information

online at www.samsung.com.

• R-600a or R-134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for your

refrigerator. If this product contains ﬂammable

gas (Refrigerant R-600a), contact your local

authority in regard to safe disposal of this

product.

• It is hazardous for anyone other than an

Authorized Service Person to service this

appliance.

Warning :

Risk of ﬁre

/ ﬂammable

materials

Important safety symbols and

precautions:

WARNING

Hazards or unsafe practices that may result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices that may result in

minor personal injury or property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions carefully.

Unplug the power plug from the wall socket.

Make sure the refrigerator is grounded

to prevent electric shock.

Call the contact center for help.

Note.

These warning signs are here to prevent

injury to you and others.

Please follow them carefully.

After reading this section, keep it in a safe

place for future reference.

STATE OF CALIFORNIA

PROPOSITION 65

WARNING

• Cancer and Reproductive Harm - www.

P65Warnings.ca.gov.

SEVERE WARNING SIGNS

FOR INSTALLATION

• Do not install the refrigerator in a damp

place or place where it may come in

contact with water.

- Deteriorated insulation of electrical parts may

cause an electric shock or ﬁre.

• Do not place this refrigerator in direct sunlight

or expose to the heat from stoves, room

heaters or other appliance.

• Do not plug several appliances into the same

multiple power strip. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matches the voltage listed on the refrigerator’s

rating plate.

- This provides the best performance and

also prevents overloading house wiring

circuits, which could cause a ﬁre hazard from

overheated wires.

WARNING

DA68-02657A-12.indb 2 2018. 10. 8. 오후 5:45

Safety information _03

• If the wall socket is loose, do not insert the

power plug.

- There is a risk of electric shock of ﬁre.

• Do not use a cord that shows cracks or

abrasion damage along its length or at either

end.

• Do not bend the power cord excessively or

place heavy articles on it.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

- When moving the refrigerator, be careful not to

roll over or damage the power cord

- This may result in an electric shock or ﬁre.

• Never unplug your refrigerator by pulling on the

power cord. Always grip plug ﬁrmly and pull

straight out from the outlet.

- Damage to the cord may cause a short-circuit,

ﬁre and/or electric shock.

• Do not use aerosols near the refrigerator.

- Aerosols used near the refrigerator may cause

an explosion or ﬁre.

• Do not install this appliance near a heater,

inﬂammable material.

• Do not install this appliance in a humid, oily or

dusty location, in a location exposed to direct

sunlight and water (rain drops).

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or ﬁre.

• This appliance must be properly grounded.

Do not ground the appliance to a gas pipe,

plastic water pipe, or telephone line.

- You must ground the refrigerator to prevent

any power leakages or electric shocks caused

by current leakage from the refrigerator.

- This may result in an electric shock, ﬁre,

explosion, or problems with the product.

- Never plug the power cord into a socket that

is not grounded correctly and make sure that it

is in accordance with local and national codes.

This appliance should be positioned in such a

way that it is accessible to the power plug.

- Failing to do so may result in an electric shock

or ﬁre due to electric leakage.

• This refrigerator must be properly

installed and located in accordance

with the manual before it is used.

• Connect the power plug in the proper position

with the cord hanging down.

- If you connect the power plug upside down,

the wire can get cut o and cause a ﬁre or

electric shock.

• When moving the refrigerator, be careful not to

roll over or damage the power cord.

- This constitutes a ﬁre hazard.

• Make sure that the power plug is not

squashed or damaged by the back of the

refrigerator.

• Keep the packing materials out of reach of

children.

- There is a risk of death from suocation if a child

puts the packing materials on his or her head.

• The appliance must be positioned so that the

plug is accessible after installation.

• You need to remove all the protective plastic

ﬁlm before you initially plug the product in.

• When disposing of this or other refrigerator/s,

remove the door/door seals, door latch so that

children or animals cannot become trapped

inside. Children should be supervised to

ensure that they do not enter and play with the

appliance.

- If trapped inside, the child may become injury

and suocate to death.

• The refrigerator must be safely

grounded.

- Always make sure that you have grounded the

refrigerator before attempting to investigate

or repair any part of the appliance. Power

leakages can cause severe electric shock.

• Never use gas pipes, telephone lines or other

potential lightning attractors as an electrical

ground.

- Improper use of the grounding plug can result

in a risk of electric shock. If it is necessary

to use an extension cord, use only a 3-wire

extension cord that has a 3-blade grounding

plug and a 3-slot receptacle that will accept

the plug on the appliance. The marked rating

of the extension cord should be AC115-120

V, 10 A, or more. If a grounding adapter is

used, make sure the receptacle box is fully

grounded.

• If the products is equipped with the LED

Lamp, do not disassemble Lamp Cover and

LED Lamp by yourself.

- Please contact your service agent.

• Use only the LED Lamps provided by

manufacturer or service agent.

• If the power cord is damaged,

have it replaced immediately by the

DA68-02657A-12.indb 3 2018. 10. 8. 오후 5:45

04_ Safety information

manufacturer or its service agent.

• The wall socket must be easily accessible so

that the appliance can be quickly disconnected

from the wall socket in an emergency.

• It must be outside the area of the rear of the

appliance.

• When positioning the appliance, ensure the

power cord is not trapped or damaged.

• Do not locate multiple portable socket-outlets

or portable power supplies at the rear of the

appliance.

• Do not store explosive substances such as

aerosol cans with a ﬂammable propellant in

this appliance.

INSTALLATION

CAUTIONS

• Allow sucient space to install the

refrigerator on a ﬂat surface.

- If your refrigerator is not level, the internal

cooling system may not work correctly.

• Keep the ventilation space in the appliance

enclosure or mounting structure clear of

obstruction.

• Allow the appliance to stand for 2 hours after

installation.

• We recommend you have installed this

refrigerator by a qualiﬁed technician or service

company.

- Failing to do so may result in an electric shock,

ﬁre, explosion, problems with the product, or

injury.

• “WARNING - Improper use of the grounding

plug can result in a risk of an electric shock.

• If it is necessary to use an extension cord, use

only a 3-wire extension cord that has a 3-blade

grounding plug and a 3-slot receptacle that will

accept the plug on the appliance. The marked

rating of the extension cord should be AC115-

120 V, 10 A, or more. If a grounding adapter

is used, make sure the receptacle box is fully

grounded.

• Plug the power plug into the wall socket ﬁrmly.

Do not use a damaged power plug, damaged

power cord or loose wall socket.

- This may result in an electric shock or ﬁre.

• Do not plug several appliances into the same

multiple power board. The refrigerator should

always be plugged into its own individual

electrical outlet which has a voltage rating that

matched the rating plate.

- This provides the best performance and

also prevents overloading house wiring

circuits, which could cause a ﬁre hazard from

CAUTION

overheated wires.

• Connect the power plug in proper position with

the cord hanging down.

- If you connect the power plug upside down,

wire can get cut o and cause ﬁre or electric

shock.

• Do not pull or excessively bend the power

cord.

• Do not twist or tie the power cord.

• Do not hook the power cord over a metal

object, place a heavy object on the power

cord, insert the power cord between objects,

or push the power cord into the space behind

the appliance.

- When moving the refrigerator, be careful not to

roll over or damage the power cord

- This may result in an electric shock or ﬁre.

• Do not install this appliance near a heater,

inﬂammable material.

• Do not install this appliance in a humid, oily or

dusty location, in a location exposed to direct

sunlight and water (rain drops).

• Do not install this appliance in a location where

gas may leak.

- This may result in an electric shock or ﬁre.

• Do not attempt to repair, disassemble, or

modify the appliance yourself.

- Do not use any fuse(such as cooper, steel

wire, etc.) other than the standard fuse.

- When repairing or reinstalling the appliance is

required, contact your nearest service center.

- Failing to do so may result in an electric shock,

ﬁre, problems with the product, or injury.

• If any dust or water is in Refrigerator, pull

out power plug and contact your Samsung

Electronics service center.

- Otherwise there is a risk of ﬁre.

- If gas leak is detected, avoid any naked ﬂames

or potential sources of ignition and air the

room in which the appliance is standing for

several minutes.

CRITICAL USAGE

WARNINGS

• Do not insert the power plug with wet

hands.

• Do not store articles on the top of the

appliance.

- When you open or close the door, the articles

may fall and cause personal injury and/or

material damage.

• Do not put a container ﬁlled with water on the

refrigerator.

- If spilled, there is a risk of ﬁre or electric shock.

WARNING

DA68-02657A-12.indb 4 2018. 10. 8. 오후 5:45

Safety information _05

• Children should be supervised to ensure that

they do not play with the appliance.

- Keep ﬁngers out of “pinch point” areas;

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area.

• Do not let children hang on the door. A serious

injury may occur.

• There is a Risk of children entrapment. Do not

let children enter inside the refrigerator.

• Never put ﬁngers or other objects into the

dispenser hole, ice chute and ice maker

bucket.

- It may cause a personal injury or material

damage.

• Do not use or place any substances sensitive

to temperature such as inﬂammable sprays,

inﬂammable objects, dry ice, medicine, or

chemicals near or inside of the refrigerator.

• Do not keep volatile or inﬂammable objects or

substances (benzene, thinner, propane gas,

alcohol, ether, LP gas and other such products

etc.) in the refrigerator.

- This refrigerator is for storing food only.

- This may result in ﬁre or explosion.

• Do not store pharmaceuticals products,

scientiﬁc materials or temperature-sensitive

products in the refrigerator.

• Products that require strict temperature

controls must not be stored in the refrigerator

• Do not place or use electrical appliance inside

the refrigerator/freezer, unless they are of a

type recommended by the manufacturer.

• If you smell pharmaceutical or smoke, pull

out power plug immediately and contact your

Samsung Electronics service center

• Do not let children go inside the refrigerator.

Children could become trapped.

• Do not insert your hands into the bottom area

under the appliance.

- Any sharp edges may cause personal injury.

• Do not let children step on a drawer’s cover.

- The drawer may break and cause them to slip.

• Do not overﬁll the refrigerator with food.

- When you open the door, an item may fall out

and cause personal injury or material damage.

• Do not touch the inside walls of the freezer or

products stored in the freezer with wet hands.

- This may cause frostbite.

• Never put ﬁngers or other objects into the

water dispenser hole, ice chute, or ice maker

bucket.

- It may cause personal injury or material

damage.

• Do not spray ﬂammable gas near the

refrigerator.

- There is a risk of explosion or ﬁre.

• Do not store volatile or ﬂammable substances

in the refrigerator.

- The storage of benzene, thinner, alcohol, ether,

LP gas and other such products may cause

explosions.

• Do not store pharmaceuticals products,

scientiﬁc materials, or temperature sensitive

products in the refrigerator.

- Products that require strict temperature

controls must not be stored in the refrigerator.

• Do not place or use an electrical appliance

inside the refrigerator, unless it is of a type

recommended by the manufacturer.

• Do not stand on top of the appliance or place

objects (such as laundry, lighted candles,

lighted cigarettes, dishes, chemicals, metal

objects, etc.) on the appliance. This may result

in an electric shock, ﬁre, problems with the

product, or injury. Do not put a container ﬁlled

with water on the appliance.

- If spilled, there is a risk of ﬁre or electric shock.

• Do not use mechanical devices or any other

means to accelerate the defrosting process,

other than those recommended by the

manufacturer.

• Do not damage the refrigerant circuit.

• Do not spray volatile material such as

insecticide onto the surface of the appliance.

- As well as being harmful to humans, it may

also result in an electric shock, ﬁre or problems

with the product.

• Never stare directly at the UV LED lamp for

long periods of time.

- This may result in eye strain due to the

ultraviolet rays.

• Keep ventilation opening in the appliance

enclosure or mounting structure clear of

obstruction.

• The installation or any service of this appliance

is recommended by a qualiﬁed technician or

service company.

- Failing to do so may result in an electric shock,

ﬁre, explosion, problems with the product, or

injury.

• Do not touch the power plug with wet hands.

- This may result in an electric shock.

• Do not disassemble or repair the

refrigerator by yourself.

- You run risk of causing a ﬁre, malfunction and/

or personal injury.

DA68-02657A-12.indb 5 2018. 10. 8. 오후 5:45

06_ Safety information

- When the interior or exterior LED lamp has

gone out, please contact your service agents.

• Children should be supervised to

ensure that they do not play with the

appliance.

- Keep ﬁngers out of “pinch point” areas :

clearances between the doors and cabinet are

necessarily small. Be careful when you open

the doors when children are in the area. Do not

let children hang on the door. If not, a serious

injury may occur. Risk of children entrapment.

Do not let children enter inside the refrigerator.

• Bottles should be stored tightly together so

that they do not fall out.

• This product is intended only for the storage of

food in a domestic environment.

• If a gas leak is detected, avoid any naked

ﬂames or potential sources of ignition and air

the room in which the appliance is standing for

several minutes.

- Do not touch the appliance or power cord.

- Do not use a ventilating fan.

- A spark may result in explosion or ﬁre.

• Use only the LED Lamps provided by

manufacturer or service agents.

• If there are burning smells or smoke,

pull out power plug immediately and

contact your Samsung Electronics

service center.

• If you experience diculty when changing the

light, contact a service agent.

• If the product is equipped with LED Lamps,

do not disassemble the Lamp Cover and LED

Lamp by yourself.

- Please contact your service agents.

• If any dust or water is in refrigerator, pull out

the power plug and contact your Samsung

Electronics service center.

- Otherwise there is a risk of ﬁre.

a) Allow the appliance to stand for 2 hours after

installation.

b) To get Best performance from the product,

1) Do not place foods too closely in front of

the vents at the rear of the appliance as it

can obstruct free air circulation in the freezer

compartment.

2) Wrap the food up properly or place it in

airtight containers before putting it into the

fridge or freezer.

3) Do not put any newly introduced food for

freezing near to already existing food.

c) Do not place glass or bottles or carbonated

beverages into the freezer.

- The container may freeze and break, and this

may result in injury.

d) Please observe maximum storage times and

expiry dates of frozen goods.

e) There is no need to disconnect the refrigerator

from the power supply if you will be away for

less than three weeks. But, Remove all the food

if you are going away for the three weeks or

more. Unplug the refrigerator and clean it, rinse

and dry.

USAGE CAUTIONS

• Do not re-freeze frozen foods that

have thawed completely. Do not place

carbonated or ﬁzzy drinks in the freezer

compartment. Do not put bottles or

glass containers in the freezer.

- When the contents freeze, the glass may break

and cause personal injury.

• Use only the ice maker provided with

the refrigerator. The water supply to this

refrigerator must only be installed/connected

by a suitably qualiﬁed person and connected

to a potable water supply only. In order to

operate the ice maker properly, water pressure

of 20 ~ 125 psi is required. If you have a long

vacation or business trip and won’t use water

or ice dispensers, close the water valve.

- Otherwise, water leakage may occur.

• Wipe excess moisture from the inside and

leave the doors open.

- Otherwise, odor and mold may develop.

• Take out the right box in the refrigerator after

removing the guard(LMF-RL22*)

• Do not apply strong shock or excessiv e force

on to the surface glass.

- Broken glass may result in a personal injury

and property damage.

• Service warranty and Modiﬁcation.

Any changes or modiﬁcations

performed by a 3rd party on this

ﬁnished appliance are not covered

under Samsung warranty service,

nor can Samsung be responsible for

safety issues that result from 3rd party

modiﬁcations.

• Do not block air holes.

- If the air holes are blocked, especially with

a plastic bag, the refrigerator can be over

cooled. If this cooling period lasts too long,

the water ﬁlter may break and cause water

leakage.

CAUTION

DA68-02657A-12.indb 6 2018. 10. 8. 오후 5:45

Safety information _07

• If the refrigerator is disconnected from the

power supply, you should wait for at least ﬁve

minutes before plugging it back in.

• If you have a long vacation planned or the

refrigerator is not to be used for a long period

of time, you must empty the refrigerator and

pull out the power plug.

- Letting the refrigerator run for a long time

without using it can cause the insulation to

deteriorate and may cause a ﬁre.

- Wipe excess moisture from the inside and

leave the doors open. Otherwise, odor and

mold may develop.

• To get the best performance from the product:

- Do not place foods too close to the vents at

the rear of the appliance as it can obstruct free

air circulation in the refrigerator compartment.

- Wrap food up properly or place it in airtight

containers before putting it into the refrigerator.

• Fill the water tank, ice tray, and water cubes

only with potable water.

• If the product is ﬂooded, make sure to

contact your nearest service center.

- There is a risk of electric shock or ﬁre.

• Do not keep vegetable oil in your refrigerator’s

door bins. The oil can solidify, making it foul-

tasting and dicult to use. In addition, the

open container can leak and the leaked oil can

cause the door bin to crack. After opening an

oil container, it is best to keep the container in

a cool and shaded place such as a cupboard

or pantry.

- Examples of vegetable oil: olive oil, corn oil,

grape-seed oil, etc.

CLEANING CAUTIONS

• Do not directly spray water on the

inside or outside the refrigerator.

- There is a risk of ﬁre or electric shock.

• Do not use a hair dryer to dry the inside of the

refrigerator. Do not place a lighted candle in

the refrigerator to remove bad odors.

- This may result in an electric shock or ﬁre.

• Remove any foreign matter or dust

from the power plug pins. Do not use

a wet or damp cloth when cleaning

the plug.

- Otherwise, there is a risk of ﬁre or electric

shock.

CAUTION

• Unplug the refrigerator before cleaning

or making repairs.

• Remove all foreign substances such as dust

or water from the power plug terminals and

contact points using a dry cloth on a regular

basis.

- Unplug the power plug and clean it with a dry

cloth.

- Failing to do so may result in an electric shock

or ﬁre.

• Before cleaning or performing maintenance,

unplug the appliance from the wall socket.

- Failing to do so may result in an electric shock

or ﬁre.

• Do not clean the appliance by spraying water

directly onto it.

• Do not use benzene, thinner or alcohol to

clean the appliance.

- This may result in discoloration, deformation,

damage, electric shock or ﬁre.

• Do not spray inﬂammable gas near the

refrigerator.

• There is a risk of explosion or ﬁre.

• Install the appliance in a cool, dry room with

adequate ventilation.

• Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat

(radiator, for example).

• Never block any vents or grilles on the

appliance. Allow warm food to cool down

before placing it in the appliance.

• Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

• Do not keep the door of the appliance open

for too long when putting food in or taking

food out.

• The shorter time for which the door is open,

the less ice will form in the freezer.

• Allow clearance to the right, left, back and top

when installing.

• This will help reduce power consumption and

keep your energy bills lower.

• In the event of a power failure, call the local

oce of your Electricity Company and ask how

long it is going to last.

- Most power failures that are corrected in an

hour or two will not aect your refrigerator

temperatures. However, you should minimize

the number of door openings while the power

is o.

- But Should the power failure last more than

24hours, remove all frozen food.

• If the key is provided with refrigerator, the keys

DA68-02657A-12.indb 7 2018. 10. 8. 오후 5:45

08_ Safety information

should be kept out of the reach of children and

not be in the vicinity of the appliance.

• The appliance might not operate consistently

(possibility of defrosting of co tents or

temperature becoming too warm in the frozen

food compartment) when sited for an extended

period of time below the cold end of the range

of temperatures for which the refrigerating

appliance is designed.

• Do not store food which goes bad easily at low

temperature, such as bananas, melons.

• Your appliance is frost free, which means there

is no need to manually defrost your appliance,

as this will be carried out automatically.

• Temperature rise during defrosting can comply

with ISO requirements. But If you want to

prevent an undue rise in the temperature of

the frozen food while defrosting the appliance,

please wrap the frozen food up in several

layers of newspaper.

• Any increase in temperature of frozen food

during defrosting can shorten its storage life.

• Do not re-freeze frozen foods that have thawed

completely.

• Install the appliance in a cool, dry room with

adequate ventilation.

• Ensure that it is not exposed to direct sunlight

and never put it near a direct source of heat

(radiator, for example).

• Never block any vents or grilles on the

appliance. Allow warm food to cool down

before placing it in the appliance.

• Put frozen food in the refrigerator to thaw.

You can then use the low temperatures of the

frozen products to cool food in the refrigerator.

• Do not keep the door of the appliance open

for too long when putting food in or taking

food out.

• The shorter time for which the door is open,

the less ice will form in the freezer.

• Allow clearance to the right, left, back and top

when installing.

• This will help reduce power consumption and

keep your energy bills lower.

• To get the best energy eciency of this

product, please leave all selves, drawers and

baskets on their original position like as above

illustration.

• Use only the ice maker provided with the

refrigerator.

• The water supply to this refrigerator must only

be installed/connected by a suitably qualiﬁed

person and connected to a potable water

supply only.

• In order to operate the ice maker properly,

water pressure of 0.1 ~ 0.7 MPa is required.

• If you have a long vacation or business trip and

won’t use water or ice dispensers, close the

water valve.

- Otherwise, water leakage may occur.

• Wipe excess moisture from the inside and

leave the doors open.

- Otherwise, odor and mold may develop.

• Never stare directly at the UV LED lamp for

long periods of time.

- This may result in eye strain due to the

ultraviolet rays.

• Do not allow babies or children go inside the

drawer.

- It can cause death from suocation by

entrapment or a personal injury.

• Do not sit on the Freezer door.

- The door may be broken and cause a personal

injury.

• To prevent children entrapment, you must

reinstall the divider using provided screw after

cleaning or other actions if you removed the

divider from the drawer.

• When you use this function the energy

consumption of the refrigerator will increase.

• Remember to turn it o when you don’t

need it and return the freezer to your original

temperature setting.

power freezing

• If you need to freeze large amount of food

stu, activate Power Freeze function at least

24 hours before.

• Use a clean sponge or soft cloth and a

mild detergent in warm water to clean the

refrigerator.

• Do not use abrasive or harsh cleansers

such as window sprays, scouring cleansers,

ﬂammable ﬂuids, muriatic acid, cleaning

waxes, concentrated detergents, bleaches, or

cleansers containing petroleum products on

exterior surfaces (doors and cabinet), plastic

parts, door and interior liners, and gaskets.

- These can scratch or damage the material.

• Do not use abrasive or harsh cleansers

such as window sprays, scouring cleansers,

ﬂammable ﬂuids, muriatic acid, cleaning

waxes, concentrated detergents, bleaches, or

cleansers containing petroleum products on

DA68-02657A-12.indb 8 2018. 10. 8. 오후 5:45

Safety information _09

contents

SETTING UP YOUR FRENCH DOOR REFRIGERATOR ………………………………… 10

OPERATING YOUR FRENCH DOOR REFRIGERATOR ………………………………… 19

TROUBLESHOOTING ………………………………………………………………………… 28

APPENDIX [HOW TO ASSEMBLY THE HANDLES] ……………………………………… 31

exterior surfaces (doors and cabinet), plastic

parts, door and interior liners, and gaskets.

• Do not clean glass shelves or covers with

warm water when they are cold. Glass shelves

and covers may break if exposed to sudden

temperature changes or impacts such as

bumping or dropping.

CRITICAL DISPOSAL

WARNINGS

• Risk of child entrapment. Before you

throw away your old refrigerator or

freezer:

- Take o the doors.

- Leave the shelves in place so that children may

not easily climb inside.

• Please dispose of the packaging material for

this product in an environmentally friendly

manner.

• Ensure that none of the pipes on the back of

the appliance are damaged prior to disposal.

• R600a or R134a is used as a refrigerant.

Check the compressor label on the rear of

the appliance or the rating label inside the

fridge to see which refrigerant is used for

your refrigerator. When this product contains

ﬂammable gas(Refrigerant R600a) contact your

local authority in regard to safe disposal of this

product.

door/door seals and door latch so that

small children or animals cannot become

trapped inside. Children should be supervised

to ensure that they do not play with the

appliance.

WARNING

• Cyclopentane is used in the insulation.

The gases in the insulation material require

a special disposal procedure. Please

contact your local authorities in regard to the

environmentally safe disposal of this product.

Ensure that none of the pipes on the back of

the refrigerator are damaged prior to disposal.

Be careful that your ﬁngers are not

caught in.

THIS APPLIANCE IS INTENDED

TO BE USED IN HOUSEHOLD

AND SIMILAR APPLICATIONS

SUCH AS

• sta kitchen areas in shops, oces and other

working environments;

• farm houses and by clients in hotels, motels

and other residential type environments;

• bed and breakfast type environments;

• catering and similar non-retail applications.

CAUTION

DA68-02657A-12.indb 9 2018. 10. 8. 오후 5:45

10_ setting up

Setting up your French Door

Refrigerator

GETTING READY TO INSTALL

THE REFRIGERATOR

Congratulations on your purchase of this Samsung

French Door Refrigerator.

We hope you enjoy the state-of-art features and

eciencies that this new appliance oers.

Selecting the best location for the

refrigerator

• A location with easy access to a water supply.

• A location without direct exposure to sunlight.

• A location with a level ﬂoor.

• A location with enough space for the

refrigerator doors to open easily.

• A location that allows sucient space to the

right, left, back and top for air circulation.

• A location that allows you to move the

refrigerator easily if it needs maintenance or

service.

• Do not install the refrigerator where the

temperature will go below 50 ºF (10 ºC).

• Do not locate the refrigerator where it may

become wet.

If your refrigerator has an ice maker, allow extra

space at the back for the water line connections.

When moving your refrigerator

To prevent ﬂoor damage, be sure the

front adjusting legs are in the up position

(above the ﬂoor). Refer to ‘Adjusting the

Level’ in the manual (on page 15).

Flat-blade

screw driver(-)

Control Lever

First thing! Make sure that you can easily move

your refrigerator to its final location by measuring

doorways (both width and height), thresholds,

ceilings, stairways, etc.

CAUTION

B

A

C

E

D

B

A

C

E

D

Model RF220**/ RF221**

Depth “A” 34 3/4” (884 mm)

Width “B” 29 3/4” (758 mm)

Height “C” 65 1/4” (1655 mm)

Overall Height “D” 66 3/4” (1695 mm)

Depth “E” 37 1/4” (944 mm)

48 5/8”

(1234 mm)

13 3/8”

(340 mm)

140° 140°

2”

(50 mm)

29 3/4”

(758 mm)

30 7/8”

(784 mm)

46 1/8”

(1171 mm)

1 5/8”

(40 mm)

3 3/4”

(95 mm)

• The measurements here are based on

the design dimension, which may dier

depending on the measuring method.

DA68-02657A-12.indb 10 2018. 10. 8. 오후 5:45

setting up _11

01 SETTING UP

FLOORING

For proper installation, you must place this

refrigerator on a level, hard surface that is the

same height as the rest of the ﬂoor. This surface

should be strong enough to support a fully loaded

refrigerator, or approximately 286.6 lbs (130 kg).

To protect the ﬁnish of the ﬂooring, cut a large

section of the cardboard carton and place it under

the refrigerator where you are working. When

moving the refrigerator, you need to pull and push

it straight forwards or back. Do not wiggle it from

side to side.

ACCESSORIES AND REQUIRED

TOOLS

The following accessories are included with your

refrigerator:

Compression Fitting Compression Nut

Required Tools (Not provided)

You need the following tools to complete the

installation of your refrigerator:

Philips

screwdriver(+)

Flat-blade screw

driver(-)

Socket wrench

(10mm)

Allen wrench

(3/16”) (5mm)

REMOVING THE REFRIGERATOR

DOORS

Before removing the door/drawer, make sure you

read the following items:

Disconnect power to the refrigerator

before removing the door or drawer.

• Be careful not to drop, damage or

scratch the door/drawer while removing

them.

• Be careful not to get injured while removing the

door/drawer.

• Reattach the door/drawer properly to avoid:

- Moisture from air leakage.

- Uneven door alignment.

- Wasting energy due to improper door seal.

Disassembling the fridge door

Be careful not to drop and scratch the

doors while removing the doors.

1. Remove the 3 screws holding down the top

table and remove it.

Top Table

2. Disconnect electric wire on the top of the

refrigerator.

WARNING

DA68-02657A-12.indb 11 2018. 10. 8. 오후 5:46

12_ setting up

3. Remove the 3 hex bolts that hold the hinge

on the top of the refrigerator with the 10 mm

socket wrench.

Socket wrench

4. Remove the screw that holds the ground wire

with a philips screwdriver(+).

ground wire

5. Separate the hinge from the electric wire and

ground wire as shown above.

6. Lift the door straight up to remove.

Be careful not to drop and scratch the doors

while removing them.

7. Separate the cap on the middle hinge.

8. Remove the screw attached to the left

and right middle hinges with a philips

screwdriver(+). Remove the 2 hex head bolts

attached to the left and right middle hinges

with an allen wrench(3/16”).

Middle Hinge

Allen wrench

Disassembling the freezer door

1. After opening the Freezer door, lift the drawer

2. Remove 4 hex head bolt from both sides with

a socket wrench(10 mm)

DA68-02657A-12.indb 12 2018. 10. 8. 오후 5:46

setting up _13

01 SETTING UP

3. Remove 4 hex head bolts from both sides with

a socket wrench(10 mm).

Reassembling the fridge door

1. Insert and tighten the screw into the left

and right middle hinges with a philips

screwdriver(+).

2. Insert and tighten the 2 hex head bolts into

the left and right middle hinges with an allen

wrench(3/16”).

3. Replace the middle hinge cap.

4. Place the hole in the bottom of the left door

over the middle hinge.

5. Position the top table in place. Insert and

tighten the 3 screws into the top table with a

philips screwdriver(+).

Top Table

6. Insert the left upper hinge shaft into the hole

the corner of the fridge door.

7. Insert the upper hinges into the holes at the

top of the door. Insert and tighten the 3 hex

head bolts into the left and right upper hinges

with a socket wrench.

DA68-02657A-12.indb 13 2018. 10. 8. 오후 5:46

14_ setting up

8. Insert and tighten the ground screw into

the left and right upper hinges with a philips

screwdriver(+).

ground wire

9. Connect the electronic wire on the top of the

refrigerator.

Reassembling the freezer door

1. Pull out the rails to the full length on each sidle

of the cabinet evenly.

2. Hang the freezer door front onto open slot on

the sides.

Slot

3. With the 10mm wrench, reattach 4 bolts to

connect the rail with the door.

4. With the drawer pulled out fully, insert the

drawer box into the rail system.

Be careful not to scratch or dent the

sliding rail by letting it strike the ﬂoor.

Make sure that you mount the freezer

basket in the right position when

removing / installing the freezer door.

Failing to do so may result in the door not

opening or closing properly.

CAUTION

DA68-02657A-12.indb 14 2018. 10. 8. 오후 5:46

setting up _15

02 SETTING UP

ADJUSTING THE LEVEL

Make sure the refrigerator is level so that you can

make ﬁnal adjustments. Use a level to test if the

refrigerator is level both side to side and back to

front. If the refrigerator is not level, it will not be

possible to get the doors perfectly even, which

may cause moisture condensation and increased

energy bills. Below is an example of how to level

the refrigerator if the left side of the refrigerator is

lower than the right side.

How to adjust the level

1. Open the freezer drawer and remove the lower

basket.

2. Insert a ﬂat-blade screwdriver (-) into the

notch on the left control lever, and then turn

it counter-clockwise to level the refrigerator.

(You turn the lever clockwise to lower the

refrigerator and counterclockwise to raise it.)

ﬂat-blade

screwdriver (-)

Control Lever

Both control levers must be touching the

ﬂoor to avoid possible personal injury or

property damage because of tipping.

• If the right side is lower, perform the

same procedure, but with the right

control lever.

• It is dicult to remove the cover leg

front from the refrigerator, so we do not

recommend making small adjustments

with the control lever. Instead, refer to

the next page for the best way to make

minor adjustments to the doors.

CAUTION

MAKING MINOR ADJUSTMENTS

BETWEEN DOORS

Remember, a leveled refrigerator is necessary

for getting the doors perfectly even. If you need

help, review the previous section on leveling the

refrigerator.

Adjustment

part

Fixed part

• The left door is ﬁxed. To make minor

adjustments between doors, adjust only

the right door.

1. Pull out the freezer drawer ( 1 ), then you can

see the lower hinge ( 2 ).

2. Insert a philips screwdriver (+) ( 3 ) into the

shaft ( 4 ) of the lower hinge.

3. Adjust the height by turning a philips

screwdriver (+) ( 3 ) clockwise (

DOWN

) or

counterclockwise (

UP

).

1

2

3

4

3

• When you turn a philips screwdriver (+)

counterclockwise (

UP

), the door will

move up.

DA68-02657A-12.indb 15 2018. 10. 8. 오후 5:46

16_ setting up

INSTALLATION OF THE WATER

LINE

Before You Install the water line

• The water line installation is not warranted by

the refrigerator manufacturer.

So before you install the water line, read the

whole steps for installing and follow these

instructions carefully to minimize the risk of

expensive water damage.

• Banging pipes (water banging in the pipes) in

house plumbing can cause damage to fridge

parts and lead to water leakage or ﬂooding.

Call a qualiﬁed plumber to correct the problem

before installing the water supply line to the

fridge.

• To prevent burns and product damage, do not

hook up the water line to the hot water line.

• Do not install the water line in areas where

temperatures fall below freezing.

• When using any electrical device (such as

a power drill) during installation, be sure the

device is insulated or wired in a manner to

prevent electric shock.

• All installations must be in a accordance with

local plumbing code requirements.

• Water line Kit and water ﬁlter are not

covered by Samsung’s Warranty.

The manufacturer (or dealer, installer)

of them is responsible for any defects

and all the loss caused by water ﬁlter &

water line kit.

• The ﬁlter should be replaced according to

manufacturer (or dealer)’s instruction.

• To order additional water ﬁlters, please contact

the manufacturer (or dealer) of the ﬁlter.

Using the water ﬁlter (not provided)

Connecting to water supply line

• Shut o the main water supply line and turn

the Ice maker to the o position.

• Locate the nearest cold drinking water line.

• Follow the instructions in the water ﬁlter

installation kit.

• After connecting the water supply line to the

Cartridge Holder inlet and installing the Filter

Cartridge (insert plastic line in fully).

• Turn on water supply and Flush 3 gallons

through ﬁlter before use (ﬂ ush approximately

6 minutes)

1. Cold Water line

2. Pipe Clamp.

3. Plastic line

4. Compression Nut

5. Compression Sleeve

6. Packing Nut

7. Shut O Valve

8. Filter Cartridge

9. Cartridge Holder

90 degree

• The water ﬁlter must be installed outside

the refrigerator.

It is not provided with your new

refrigerator. The ﬁlter cartridge (8) and

holder (9) kit can be purchased from

the retailer where you purchased this

refrigerator.

• Do not use copper line.

• Cut the tubing, making sure the ends are

square and clean

Incorrect

Correct

There are several items that you need to purchase

to complete this connection.

You may ﬁnd these items sold as a kit at your local

hardware store.

Use Copper Tubing Use Plastic Tubing

• ¼” copper tubing

• ¼” compression nut (1pc)

• Ferrule (2pc)

• ¼” plastic tubing

 Molded end(Bulb)

• ¼” compression nut (1pc)

Connect the water line to the fridge

• Connect the plastic line on the back of your

fridge to the cartridge holder outlet (fully insert

the plastic line to the cartridge holder outlet).

• Insert plastic clip to the cartridge holder inlet

and outlet.

• Turn water on and check for any leakage.

DA68-02657A-12.indb 16 2018. 10. 8. 오후 5:46

setting up _17

01 SETTING UP

Clip

Filter

cartridge

Plastic line

(Purchased)

Cartridge

Holder

• You can purchase the necessary ﬁlter

cartridge at the retailer where you

purchased this refrigerator.

• Water line must be connected to drinkable

water only.

• When pushing the Refrigerator back, make

sure you don’t roll over the power cord or

water line(Icemaker supply line).

• Use the new hose-sets supplied with the

appliance only. Do not re-use an old hose set.

Keep ventilation openings, in the

appliance enclosure or in the built-in

structure, clear of obstruction. Connect

to potable water supply only.

To use without the water ﬁlter

Connecting to the water supply line

• Shut o the main water supply line and turn the

Ice maker to the o position.

• Locate the nearest cold water drinking line.

1. Cold Water line

2. Pipe Clamp.

3. Plastic line

4. Compression Nut

5. Compression Sleeve

6. Packing Nut.

7. Shut O Valve

WARNING

Connect the water line to the fridge

1. Slip the compression nut through the plastic

tubing.

2. After inserting the compression nut into plastic

tubing, tighten the compression nut onto 1/4”

compression ﬁtting (Purchased).

Ferrule

(Purchased)

Plastic Tubing

(Purchased)

Compression

Nut (1/4”)

(Purchased)

Bulb

Compression

ﬁtting *

Compression

Nut (1/4”) *

* Accesory included

(Not supplied)

Copper tubing or Plastic tubing

Household water line

Refrigerator

• Do not overtighten the compression nut.

• Using Copper Tubing

- Slip the compression nut and ferrule on copper

tubing as shown.

• Using Plastic Tubing

- Insert the molded end(Bulb) of the plastic

tubing into the compression ﬁtting.

Do not use without the molded end(Bulb)

of the plastic tubing.

3. Tighten the compression nut onto the

compression ﬁtting.

4. Turn water on and check for any leakage.

• You can purchase the necessary ﬁlter

cartridge at the retailer where you

purchased this refrigerator.

• Water line must be connected to drinkable

water only.

• When pushing the Refrigerator back, make

sure you don’t roll over the power cord or

water line (Icemaker supply line).

CAUTION

DA68-02657A-12.indb 17 2018. 10. 8. 오후 5:46

18_ operating

Do not use without the molded end (Bulb)

of the plastic tubing ( B ).

1. Tighten the compression nut ( B ) onto the

compression ﬁtting.

Do not over-tighten the compression nut ( B ).

2. Turn water on and check for any leakage.

If you ﬁnd water drops or leakage in the

connection areas, turn o the main water

supply. Check the connections and, if

necessary, tighten.

3. Flush 1 gallon of water through the ﬁlter

before drinking or using the water from the

refrigerator. (Flush approximately 6 minutes.)

To ﬂush, press a large glass or cup against the

water dispenser lever. Fill the glass, empty it

into the kitchen sink after it is ﬁlled, and then

repeat.

4. After you turn on the refrigerator, let the ice

maker make ice for 1 to 2 days. Over that

period of time, throw out the ﬁrst 1 or 2

buckets of ice the freezer makes to ensure all

impurities have been removed from the water

line.

• Only connect the water line to a

drinkable water source.

• If you have to repair or disassemble the water

line, cut o 1/4” of the plastic tubing to make

sure you get a snug, leak-free connection.

CAUTION

COMPLETING THE SET UP

Now that you have your new refrigerator installed

in place, you are ready to set up and enjoy the

features and functions of the appliance.

By completing the following steps, your refrigerator

should be fully operational.

1. Make sure your refrigerator is in an appropriate

location with reasonable clearance between it

and the wall. Refer to installation instructions in

this manual.

2. Once the refrigerator is plugged in, make sure

the interior light comes on when you open the

doors.

3. Set the Temperature control to the coldest

temperature and wait for an hour. The freezer

will get slightly chilled and the motor will run

smoothly. Reset the refrigerator and freezer to

the temperatures you want.

4. After you plug the refrigerator in, it will

take a few hours to reach the appropriate

temperature. You can store food and drinks

in the refrigerator after the temperature is

suciently cool.

DA68-02657A-12.indb 18 2018. 10. 8. 오후 5:46

operating _19

02 OPERATING

Operating your French Door

Refrigerator

( 1 )

Freezer

(Hold 3 sec for

Power Freeze)

Press the Freezer button to set the freezer temperature between colder and coldest.

Press and hold the Freezer button for 3 seconds to activate Power Freezer function which

speeds up the freezing process in the freezer.

( 2 )

Fridge

Press the Fridge button to set the Fridge temperature between cold and coldest.

( 3 )

Energy Saver

For better energy eciency, press the Energy Saver button. If condensation occurs on the

doors, turn the Energy Saver Button function o.

( 4 )

Ice O

If you don’t want to make more ice, Press the Ice O button. The LED will light up and the

Ice-Maker stops making ice.

( 5 )

Alarm On/O

Press the Alarm On/O button to turn the door open alarm on and o.

( 6 )

Power Freeze

Press this button to activate Power Freezer function which speeds up the freezing process

in the freezer.

CHECKING THE CONTROL PANEL

v





G

{









G

w







G

~









[RF221, RF220]

[RL225]

[RL220]

1 2 3

4

6

5

DA68-02657A-12.indb 19 2018. 10. 8. 오후 5:46

20_ operating

USING THE CONTROL PANEL

Freezer/Fridge (Temperature

adjustment)

Press the Freezer or Fridge button until the desired

temperature is set. For lower temperature, press

the Freezer or Fridge button until more LED

lights (coldest). For higher temperature, press

the Freezer or Fridge button until less LED lights

(colder).

Each time you press the Freezer or Fridge button,

temperature indicator will change in below order.

Power Freeze

RF221 / RF220 / RL225

This icon will light up when you activate the Power

Freeze function. Power Freeze function generates

cool air for 50 hours continuously and it makes the

inside of the refrigerator cool faster. This function

is useful when you make ice more quickly.

When you have enough, just press and hold

the Freeze (Hold 3 sec for Power Freeze) button

again for 3 seconds to cancel the Power Freeze

function.

RL220

This icon will light up when you activate the Power

Freeze function. Power Freeze function generates

cool air for 50 hours continuously and it makes

the inside of the refrigerator cool faster. When you

have enough, just press the Power Freeze button

again to cancel the Power Freeze function.

• When you use this function the energy

consumption of the refrigerator may

increase. Remember to turn it o when

you do not need it and return the freezer

to your original temperature setting.

Energy Saver

This LED will light up when you activate the Energy

Saver function. The Energy Saver function is

automatically set to “ON” when power is supplied

to the Refrigerator. If condensation occurs on the

doors, turn the Energy Saver function o.

• In some places, water drop may be

generated on the door part. In this case,

it is recommended to turn o the Energy

saver function.

Ice O

This LED will light up when you activate the Ice O

function. In this case, the ice will not be produced.

Alarm On/O

If the door alarm is set to On, an alarm beeps if

any refrigerator door is left open for more than

three minutes. The beeping stops when you close

the door. The door alarm function is pre-set to On

in the factory. You can turn it o by touching and

then releasing this button. You can turn it back on

in the same fashion. The LED lights up when the

function is on.

Canceling cooling o mode (Freezer/

Fridge Temperature Indicator moving)

• Cooling o function is for store display,

and it makes the refrigerator not to

generate cool air. (Only for product sold

in U.S)

[RF221, RF220]

[RL225]

[RL220]

In case of Cooling o Mode, refrigerator

may seem like working but it does not

make cool air. To cancel this mode, press

the “Cooling O Key” at the same time

for 5 seconds until “Ding-dong” sounds.

COOLING OFF KEY

RF221, RF220, RL225 Model :

Ice O + Freezer Key

RL220 Model :

Power Freeze + Freezer Key

CAUTION

DA68-02657A-12.indb 20 2018. 10. 8. 오후 5:46

La page charge ...

Samsung RF220NFTAWW/AA Manuel utilisateur

Samsung RF220NFTAWW/AA Manuel utilisateur

dans d''autres langues

Documents connexes