LG WM3455HW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire
P/No.: MFL63288611
WM3455H*
Model/Modelo/Modèle
Designed specially to use only
HE (High-Efficiency) detergent
Diseñada específicamente para usar con
el detergente tipo HE (Alta eficiencia)
Spécialement conçu pour
utilisation avec un détergent haute ef-
ficacité uniquement
To contact LG Electronics, 24 hours a day,
7 days a week:
1-800-243-0000
Or visit us on the Web at: us.lge.com
Número telefónico de LG Electronics, las 24
horas del día, 7 días a la semana:
1-800-243-0000
O visítenos en la Web en: us.lge.com
To contact LG Electronics, 24 hours a day,
7 days a week:
1-888-LGCANADA
Or visit us on the Web at: ca.lge.com
Pour contacter LG Electronics, 24 heures par
jour, 7 jours par semaine :
1-888-LGCANADA
Ou visitez notre site Web à l’adresse : ca.lge.com
Before beginning installation, read these instructions
carefully. This wll simplify installation and ensure that the
washer is installed correctly and safely. Leave these instructions
near the washer after installation for future reference.
USERS GUIDE &
INSTALLATION INSTRUCTIONS
Front Loading Combo
Antes de comenzar la instalación, lea atentamente estas
instrucciones. Esto simplificará la instalación y asegurará que
la lavadora está instalada en forma correcta y segura. Conserve
estas instrucciones cerca de la lavadora luego de la instalación
para futuras consultas.
GUÍA DEL USUARIO E
INSTRUCCIONES DE INSTALACIÓN
Lavadora de Carga
Frontal
Avant de commencer à installer votre machine à laver, lisez at-
tentivement ces instructions. Cela simplifiera votre installation
et assurera que la machine à laver est installée correctement et
en toute sécurité. Conservez ces instructions à proximité de la
machine à laver après son installation, pour référence future.
GUIDE DE LUTILISATEUR ET
DIRECTIVES DINSTALLATION
Lave-linge et
chargement frontal
Congratulations on your purchase
and welcome to the LG family.
Your new LG washing machine
combines the most advanced
washing technology with simple
operation and high efficiency.
Follow the operating and care in-
structions in this manual and your
washer will provide many years of
reliable service.
THANK YOU!
I N T RO D U C T I O N
INSTALLATION INSTRUCTIONS
Choose the Proper Location .................................. 8
Clearances ............................................................. 8
Flooring .................................................................. 9
Unpacking ............................................................ 10
Connecting the Water Lines ................................. 11
Connecting the Drain Line .................................... 12
Leveling the Washer ............................................. 13
Installation of non-skid pads (optional) ................ 13
HOW TO USE
Sorting Wash Loads ............................................. 14
Selecting Detergent .............................................. 15
About the Dispenser ............................................. 15
Loading the Dispenser ......................................... 16
Control Panel Features ......................................... 17
Cycle Guide .......................................................... 18
The LED Display ................................................... 19
Operating the Washer .......................................... 20
Cycle Setting Buttons .......................................... 21
Cycle Option Buttons .......................................... 22
Special Functions ................................................. 23
PARTS AND FEATURES
Special Features ..................................................... 7
TROUBLESHOOTING
Normal Sounds You May Hear ............................. 28
Before Calling for Service ............................... 28-30
CARE AND CLEANING
Regular Cleaning ............................................ 24-25
Cleaning the Washer ............................................ 25
Maintenance ................................................... 26–27
WARRANTY ..............................................32-33
SPECIFICATION
IMPORTANT SAFETY INSTRUCTIONS
Basic Safety Precautions .................................. 3-6
Key Dimensions and Specifi cations ..................... 31
Product Registration Information
Model:
Serial Number:
Date of Purchase:
The model and serial number can be located on
the rating plate on the front of the washer.
Staple your receipt here.
2
I M P O RTA N T S A F E T Y I N S T RU C T I O N S
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
Your Safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read
and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
wDANGER: You can be killed or seriously injured if you don’t follow instructions immediately.
wWARNING: You can be killed or seriously injured if you don’t follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of
injury, and tell you what can happen if the instructions are not followed.
3
READ ALL INSTRUCTIONS BEFORE USE
Before use, the washer must be properly installed as
described in this manual.
Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with
gasoline, dry cleaning solvents, or other fl ammable
or explosive substances, as they give off vapors that
could ignite or explode.
Do not add gasoline, dry cleaning solvents, or other
ammable or explosive substances to the wash
water. These substances give off vapors that could
ignite or explode.
Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been
used for 2 weeks or more. HYDROGEN GAS IS
EXPLOSIVE. If the hot water system has not been
used for such a period, before using the washer,
turn on all hot water faucets and let the water fl ow
from each for several minutes. This will release any
accumulated hydrogen gas. As the gas is fl ammable,
do not smoke or use an open fl ame during this time.
Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children.
Before the washer is removed from service or
discarded, remove the door to prevent children from
climbing inside.
Do not install or store the washer where it will be
exposed to the weather or freezing temperatures.
Do not tamper with controls.
Do not repair or replace any part of the washer or
attempt any servicing other than as described in this
manual. We strongly recommend that any service be
performed by a qualifi ed individual.
See Installation Instructions for grounding
requirements.
ALWAYS follow the fabric care instructions
supplied by the garment manufacturer.
Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fi re.
Use fabric softeners or products to eliminate static
only as recommended by the manufacturer.
This washer is not designed for maritime use or for
mobile installations such as in RVs, aircraft, etc.
Turn off the water taps and unplug the washer if the
machine is to be left for an extended period of time,
such as during vacations.
Packaging material can be dangerous for children.
There is a risk of suffocation! Keep all packaging
from children.
Always check the inside of the washer for foreign
objects before loading laundry. Keep the door closed
when not in use.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following.
BASIC SAFETY PRECAUTIONS
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fi re or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
READ ALL INSTRUCTIONS BEFORE USE
I M P O RTA N T S A F E T Y I N S T RU C T I O N S
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least resistance for electric current. This appliance is
equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must
be plugged into an appropriate outlet that is properly installed and grounded in accordance with all
local codes and ordinances.
GROUNDING INSTRUCTIONS
wWARNING: Improper connection of the equipment-grounding conductor can result in risk
of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether the
appliance is properly grounded. Do not modify the plug provided with the appliance. If it does not fit the
outlet, have a proper outlet installed by a qualified electrician. Failure to follow these warnings can cause
serious injury, fire, electrical shock, or death.
4
Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures. Installation
instructions are packed in the washer for installer
s
reference. If the washer is moved to a new location,
have it checked and reinstalled by a qualified service
person. Failure to follow this warning can cause
serious injury, fire, electrical shock, or death.
Do not, under any circumstances cut or remove
the third (ground) prong from the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
For personal safety, this appliance must be
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
The power cord of this appliance is equipped
with a 3-prong (grounding) plug which mates
with a standard 3-prong (grounding) wall outlet to
minimize the possibillty of electric shock hazard from
this appliance.
This washer must be plugged into a 120 VAC,
60 Hz grounded outlet. Failure to follow this warning
can cause serious injury, fire, electrical shock, or
death.
Have the wall outlet and circuit checked by a
qualified electrician to make sure the outlet is
properly grounded. Failure to follow this warning
can cause serious injury, fire, electrical shock,
or death.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility
and obligation to have it replaced with a properly
grounded 3-prong wall outlet. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
Do not install on carpet. Install washer on a solid
floor. Failure to follow this warning can cause serious
leak damage.
Do not remove ground prong. Do not use an
adapter or extension cord. Plug into a grounded
3-prong outlet. Failure to follow these warnings can
cause serious injury, fire, electrical shock, or death.
The washer should always be plugged into its
own individual electrical outlet which has a
voltage rating that matches the rating plate. This
provides the best performance and also prevents
overloading house wiring circuits which could cause
a fire hazard from overheated wires.
Never unplug your washer by pulling on the
power cord. Always grip plug firmly and pull straight
out from the outlet. Failure to follow this warning can
cause serious injury, fire, electrical shock, or death.
Repair or replace immediately all power cords
that have become frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end. Failure
to follow this warning can cause serious injury, fire,
electrical shock, or death.
When installing or moving the washer, be careful
not to pinch, crush, or damage the power cord.
Failure to follow this warning can cause serious
injury, fire, electrical shock, or death.
The washer must be installed and electrically
grounded by a qualified service person in
accordance with local codes to prevent shock
hazard and assure stability during operation.
Washer is heavy. Two or more people may be
need to install and move the appliance. Failure to
do so can result in back or other injury.
Store and install the washer where it will not
be exposed to temperatures below freezing or
exposed to outdoor weather conditions. Failure to
follow this warning can cause serious leak damage.
Do not install the washer in humid spaces to
reduce the risk of electric shock. Failure to follow
this warning can cause serious injury, fire, electrical
shock, or death.
To reduce the risk of personal injury, adhere to
all industry recommended safety procedures
including the use of long sleeved gloves and
safety glasses. Failure to follow all of the safety
warnings in this manual could result in property
damage, personal injury or death.
wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this
appliance, follow basic precautions, including the following.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fire or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
READ ALL INSTRUCTIONS BEFORE USE
I M P O RTA N T S A F E T Y I N S T RU C T I O N S
5
I M P O RTA N T S A F E T Y I N S T RU C T I O N S
SAFETY INSTRUCTIONS FOR USE, CARE AND CLEANING, AND DISPOSAL
Unplug the washer before cleaning to avoid the
risk of electric shock.
Never use harsh chemicals, abrasive cleaners,
or solvents to clean the washer. They will
damage the fi nish.
Do not put oily or greasy rags or clothing on
top of the washer. These substances give off
vapors that could ignite the materials.
Do not wash items that are soiled with
vegetable or cooking oil. These items may
contain some oil after laundering. Due to the
remaining oil, the fabric may smoke or catch
re by itself.
Disconnect this appliance from the
power supply before attempting any user
maintenance. Turning the controls to the OFF
position does not disconnect this appliance
from the power supply. Failure to follow this
warning can cause serious injury, fi re, electrical
shock, or death.
Do not combine laundry products for use in
one load unless specifi ed on the label.
Do not mix chlorine bleach with ammonia
or acids such as vinegar. Follow package
directions when using laundry products.
Incorrect usage can produce poisonous gas,
resulting in serious injury or death.
Do not reach into the washer while parts are
moving. Before loading, unloading, or adding
items, press the START/PAUSE button and
allow the drum to coast to a complete stop
before reaching inside. Failure to follow this
warning can cause serious injury, fi re, electrical
shock, or death.
Do not allow children to play on or in the
washer. Close supervision of children is
necessary when the washer is used near
children. As children grow, teach them the
proper, safe use of all appliances. Failure to
comply with these warnings could result in serious
personal injuries.
Destroy the carton, plastic bag and other
packing materials after the washer is
unpacked. Children might use them for play.
Cartons covered with rugs, bedspreads, or
plastic sheets can become airtight chambers.
Failure to comply with these warnings could result
in serious personal injuries or death.
Keep laundry products out of children’s reach.
To prevent personal injury, observe all warnings
on product labels. Failure to comply with these
warnings could result in serious personal injuries.
Remove the door to the washing compartment
to avoid the danger of children or small animals
getting trapped inside before your washer is
removed from service or discarded. Failure
to do so can result in serious personal injury
or death.
wWARNING: To reduce the risk of fire, electric shock, or personal injury when using this
appliance, follow basic precautions, including the following.
6
SAVE THESE INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWARNING For your safety, the information in this manual must be
followed to minimize the risk of fi re or explosion, electric shock, or to prevent
property damage, personal injury, or loss of life.
PA RT S A N D F E AT U R E S
3
2
1
4
5
DETERGENT DISPENSER DRAWER
This three-compartment drawer provides separate
dispensers for prewash and main wash detergent,
and liquid fabric softener.
CONTROL PANEL WITH LED DISPLAY
Simple electronic controls are user-friendly.
The LED display indicates cycle options and
cycle time during operation.
LARGE-CAPACITY STAINLESS STEEL DRUM
The large capacity stainless steel drum offers
extreme durability and is tilted to improve
efficiency and allow easier access for large items.
NOTE: No matter how large the article, there
must still be room for the clothes to tumble.
DIRECT-DRIVE MOTOR
Direct-drive motor eliminates the belt and pulleys
found on most washers to provide improved
performance and reliability while increasing
energy efficiency.
DRAIN ACCESS PANEL
Provides access to the drain line and drain
pump filter.
EASY-ACCESS DOOR
Extra-large door locks during operation and
features a delay to prevent the door from being
opened until the washer interior has cooled and
the water level has lowered.
LEVELING FEET
Four leveling feet (two in the front and two in
the back) adjust to improve washer stability on
uneven floors.
7
Rear of Washer
6
Included Accessories
Hot and Cold
Water Hoses
Wrench
(for removing shipping
bolts and adjusting
leveling feet)
Tie Strap
(for securing
drain hose)
Elbow Bracket
(for securing drain
hose)
Non-skid pads
Caps (4)
(for covering
shipping bolt holes)
7
SPECIAL FEATURES
6
1
2
4
3
5
7
I N S TA L L AT I O N I N S T RUCTIONS
CHOOSE THE PROPER LOCATION
CLEARANCES
Allow at least 19.8 in. (50.3 cm) in front of the
washer to open the door.
To ensure sufficient clearance for water lines and
airflow, allow minimum clearances of at least
1 in. (2.5 cm) at the sides and 4 in. (10 cm)
behind the unit. Be sure to allow for wall, door,
or floor moldings that may increase the required
clearances.
Do not remove ground prong. Do not use
an adapter or extension cord. Plug into a
grounded 3-prong outlet. Failure to follow this
warning can cause serious injury, fi re, electrical
shock, or death.
Power Outlet
The power outlet must be within 60 in. (1.5 m) of
either side of the washer.
The appliance and outlet must be positioned so
that the plug is easily accessible.
Do not overload the outlet with more than one
appliance.
The outlet must be grounded in accordance with
current wiring codes and regulations.
Time-delay fuse or circuit breaker is
recommended.
NOTE: It is the personal responsibility and
obligation of the product owner to have a
proper outlet installed by a qualified electrician.
wWARNING
Washer is heavy! Two or more people
are required when moving and unpacking
the washer. Failure to do so can result in back
or other injury.
Store and install the washer where it will not
be exposed to temperatures below freezing
or exposed to outdoor weather conditions.
Failure to follow this warning can cause serious
injury, fi re, electrical shock, or death.
Properly ground washer to conform with all
governing codes and ordinances. Failure to
follow this warning can cause serious injury, fi re,
electrical shock, or death.
To reduce the risk of electric shock, do not
install the washer in humid spaces. Failure to
follow this warning can cause serious injury, fi re,
electrical shock, or death.
8
21.6" (54.86 cm)
25.2" (64 cm)
45" (114.3 cm)
33.5" (85.09 cm)
3.5" (8.89 cm)
24" (60.96 cm) 1" (2.5 cm)1" (2.5 cm)
I N S TA L L AT I O N I N S T RUCTIONS
FLOORING
NOTE: Please note that the floor must be strong
and rigid enough to support the weight of the
washer when fully loaded, without flexing or
bouncing. If your floor has too much flex in it,
you may need to reinforce it to make it more
rigid. A floor that is adequate for a top-loading
washer may not be rigid enough for a front-
loading washer due to the difference in the spin
speed and direction. If the floor is not solid, your
washer may vibrate and you may hear and feel
the vibration throughout your house.
To minimize noise and vibration, the washer
MUST be installed on a solidly constructed floor.
See the NOTE at right.
Allowable slope under the entire washer is
maximum.
Carpeting and soft tile surfaces are not
recommended.
Never install the washer on a platform or weakly
supported structure. Use only an approved
accessory pedestal as described below.
NOTE: Before installing the
washer, make sure the floor is
clean, dry and free of dust, dirt,
water and oils so the washer feet
can not slide easily. Leveling
feet that can move or slide on the floor can
contribute to excess vibration and noise due to
poor contact with the floor.
A
B
9
I N S TA L L AT I O N I N S T RUCTIONS
If you must lay the washer down to remove the
base packaging materials, always lay it carefully
on its side. Do NOT lay the washer on its front
or back.
IMPORTANT: To prevent internal damage
during transport, the washer is equipped with
4 shipping bolts and plastic retainers. These
bolts and retainers MUST be removed before
operating the washer.
Failure to remove shipping bolts and retainers
may cause severe vibration and noise, which can
lead to permanent damage to the washer. The
cord is secured to the back of the washer with
a shipping bolt to help prevent operation with
shipping bolts in place.
Remove the retainers by turning them slightly
while pulling. Rotate and press the hole caps
into the shipping bolt holes.
Starting with the bottom 2 shipping bolts,
use the included wrench to remove the
4 shipping bolts by turning them
counterclockwise.
1
2
NOTE: Save the bolts and retainers for
future use. To prevent damage to internal
components, the shipping bolts and
retainers must be installed when
transporting the washer.
Cap
Carton Base
UNPACKING
10
I N S TA L L AT I O N I N S T RUCTIONS
CONNECTING THE WATER LINES
Insert a rubber seal into the threaded
fittings on each hose.
1
Rubber Seal
Water Hose
(to tap)
Rubber Seal
Water Hose
(to water inlet
on washer)
3
Attach the hot water line to the hot water
tap. Attach the cold water line to the cold
water tap.
Tighten the fittings securely. Open the water
taps fully to check for leaks.
Water Tap
NOTE: Do not cross-thread the hose fittings.
Attach the hot water line to the red hot water
inlet on the back of the washer. Attach the
cold water line to the blue cold water inlet on
the back of the washer. Tighten the fittings
securely.
2
IMPORTANT: Use new hoses when installing
the washer. Do NOT reuse old hoses.
IMPORTANT: Use ONLY the inlet hoses
provided by LG with this laundry product.
Aftermarket hoses are not guaranteed to fit or
function correctly. Other hoses may not tighten
correctly and could cause leaks. Subsequent
damage to product or property will not be
covered under the terms of LG's warranty.
Water supply pressure must be between 14.5
PSI and 116 PSI (100~800 kPa). If the water
supply pressure is more than 116 PSI,
a pressure reducing valve must be installed.
Periodically check the hose for cracks, leaks,
and wear, and replace the hose if necessary.
Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
The washer should never be installed or stored
in a location subject to freezing temperatures.
Damage to the water lines and internal
mechanisms of the washer can result. If the
washer was exposed to freezing temperatures
prior to installation, allow it to stand at room
temperature for several hours before use.
11
Cold Hot(option)
Hot water tap
Cold
water
tap
I N S TA L L AT I O N I N S T RUCTIONS
CONNECTING THE DRAIN LINE
Stand
Pipe
Tie Strap
Clip the end of the hose into the elbow bracket.
Insert the end of the drain hose into a standpipe.
Use tie strap to secure the drain hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
Option 1: Standpipe
Elbow
Bracket
Drain
Hose
Clip the end of the hose into the elbow bracket.
Hang the end of the drain hose over the side of
the laundry tub. Use tie strap to secure the drain
hose in place.
NOTE: Total height of the hose end should not
exceed 96 in. (244.8 cm) from the bottom of the
washer.
Laundry
Tub
Option 2: Laundry Tub
Elbow
Bracket
Tie
Strap
Drain
Hose
The drain hose should always be properly
secured. Failure to properly secure the drain
hose can result in fl ooding and property
damage.
Do not install the end of the drain hose higher
than 96 in. (244.8 cm) above the bottom of the
washer.
The drain must be installed in accordance with
any applicable local codes and regulations.
Make sure that the water lines are not stretched,
pinched, crushed, or kinked.
NOTE: If the drain hose is extended more than 4
inches beyond the end of the end of the elbow
bracket, mold, or microorganisms could spread to
the inside of the washer.
No more than
4 inches
Elbow Bracket
12
I N S TA L L AT I O N I N S T RUCTIONS
LEVELING THE WASHER
Position the washer in the final location, taking
special care to not pinch, strain, or crush the
water and drain lines. Place a level across the
top of the washer.
1
Leveling Feet
Leveling
Feet
The drum of your new washer spins at very high
speeds, up to 1,300 RPM. To minimize vibration,
noise, and unwanted movement, the floor must be
a perfectly level, solid surface.
NOTE: Adjust the leveling feet only as far as
necessary to level the washer. Extending the
leveling feet more than necessary can cause
the washer to vibrate.
Loosen the locknuts on all 4 leveling feet
until you can turn the feet with the included
wrench. Turn clockwise to raise the washer
or counterclockwise to lower it.
2
Raise
Lower
All four leveling feet must rest solidly on the
floor. Rock the washer gently from corner to
corner to make sure that the washer does
not rock.
3
Once the washer is level from side to side and
front to back, tighten all locknuts securely.
Make sure that all 4 leveling feet are in firm
contact with the floor.
NOTE: To make sure that the washer is
properly level, run the washer with a test load:
place approximately 6 pounds of laundry
in the machine. Then, press POWER, press
RINSE+SPIN, and then press the START/
PAUSE button. (See the following sections for
additional information on cycle selection and
operation.)
Verify that the washer does not rock or vibrate
excessively during the spin cycle.
If the washer vibrates or shakes, adjust
the leveling feet until the washer is stable and
retest.
Tighten all 4
locknuts securely
INSTALLATION OF NON-SKID PADS (OPTIONAL)
Some floor surfaces are too slippery to prevent
the washer from moving on the floor during
heavily unbalanced loads. While it is normal for
an occasional load to be out of balance, excess
noise and vibration can result from the washer
moving out of position. If these conditions are
encountered, follow the instructions below for
installation of the non-skid pads. These pads
will help prevent the washer from moving during
heavy out of balance conditions thereby reducing
noise and vibration.
A
B
[ Place the pads under both front feet.
A
B
This side up
Stick adhesive side to floor
Remove backing
Non-skid pads
13
SORTING WASH LOADS
H OW TO U S E
Fabric Care Labels
Most articles of clothing feature fabric care labels
that include instructions for proper care.
Grouping Similar Items
For best results, sort clothes into loads that can
be washed with the same wash cycle.
Different fabrics have different care requirements.
Always wash dark colors separately from light
colors and whites to prevent discoloration. If
possible, do not wash heavily soiled items with
lightly soiled ones. The chart below shows
recommended groupings.
Bleach
symbols
Any bleach
(when needed)
Only non-chlorine bleach
(when needed)
Do not bleach
Machine
wash
cycle
Normal
Permanent press/
wrinkle resistant
Gentle/
delicate
Hand wash
Do not wash Do not wring
Water
temperature
Hot
(50°C/120°F)
Warm
(40°C/105°F)
Cold/cool
(30°C/85°F)
Fabric Care Labels
Sort Laundry...
by Colors by Soil by Fabric by Lint
Whites Heavy Delicates Lint Producer
Lights Normal Easy Care Lint Collector
Darks Light Sturdy
Loading the Washer
Check all pockets to make sure that they
are empty. Items such as clips, matches,
pens, coins, and keys can damage both your
washer and your clothes.
Close zippers, hooks, and drawstrings to
prevent these items from snagging or tangling
on other clothes.
• Pretreat heavily stained areas for best results.
Combine large and small items in a load. Load
large items fi rst.
Large items should not be more than half of the
total washload.
The washer can be fully loaded, but the drum
should not be tightly packed with items. The
door of the washer should close easily.
To prevent an out-of-balance load, do not wash
single items. Add one or two similar items to
the load. Large, bulky items, such as a blanket,
comforter, or bedspread should be washed
individually.
Do not wash or spin waterproof clothes.
When unloading the washer, check under the
door seal for small items.
NOTE: The front loading washer rotates the
wet laundry to wash it with less water. If you
do not see the water during washing, it is not
a problem because the laundry is suffi ciently
wet.
REMINDER: The load must have room to
tumble to wash effectively. Just because an
item can be forced into the drum does not
mean it should be washed in the machine. It
must be able to tumble.
14
H OW TO U S E
SELECTING DETERGENT
ABOUT THE DISPENSER
The automatic dispenser consists of four
compartments which hold:
• Liquid fabric softener.
• Liquid or powdered detergent for prewash.
Liquid or powdered detergent and color-safe
bleach for main wash.
All laundry products can be added at once in
their respective dispenser compartments.
They will be dispensed at the appropriate time
for the most effective cleaning.
After adding the laundry products to the
dispenser, close the dispenser drawer.
To add detergent and fabric softener to the
automatic dispenser:
Open the dispenser drawer.
Load the laundry products into the
appropriate compartments.
Slowly close the dispenser drawer to
avoid early dispensing of the laundry
products.
NOTE: It is normal for a small amount of water to
remain in the dispenser compartments at the end
of the cycle.
1
2
3
IMPORTANT: Do not place or store laundry
products, such as detergent, bleach, or liquid
fabric softener, on top of your washer or dryer.
Wipe up any spills immediately. These products
can damage the finish and controls.
Designed specially to use only
HE (High-Efficiency) detergent
IMPORTANT: Your washing machine is
designed for use with only High-Efficiency
(HE) detergents. HE detergents are formulated
specifically for front-load washers and contain
suds-reducing agents. Always look for the HE
symbol when purchasing detergent.
HE detergents produce fewer suds, dissolve
more efficiently to improve washing and rinsing
performance, and help to keep the interior of your
washer clean.
Using a regular detergent may cause oversudsing
and unsatisfactory performance.
15
Liquid Fabric Softener
Compartment
Prewash Detergent
Compartment
Main Wash Detergent
Compartment
H OW TO U S E
LOADING THE DISPENSER
Prewash Detergent Compartment
Add liquid or powdered detergent to this
compartment when using the Prewash option.
Always use HE (High-Efficiency) detergent with
your washing machine.
The amount of detergent added for the Prewash
option is 1/2 the amount recommended for the
main wash cycle. For example, if the main wash
cycle requires TWO tablespoons (1 oz. or 30
ml) of detergent, add ONE tablespoon for the
Prewash option.
NOTE: If you are using the Prewash option,
powdered detergent must be used in the main
wash compartment. Liquid detergent will drain
into the washer drum as it is added.
Main Wash Detergent Compartment
This compartment holds laundry detergent
for the main wash cycle, which is added to
the load at the beginning of the cycle. Always
use HE (High-Efficiency) detergent with your
washing machine.
Never exceed the manufacturer’s
recommendations when adding detergent.
Using too much detergent can result in
detergent buildup in clothing and the washer.
Either powdered or liquid detergent may be used.
NOTE: Liquid detergent will drain into the washer
drum as it is added.
NOTE: Liquid or powdered color-safe bleach
may be added to the main wash compartment
with detergent of the same type.
Fabric Softener Compartment
This compartment holds liquid fabric softener,
which will be automatically dispensed during the
final rinse cycle.
Always follow the manufacturer’s
recommendations when adding fabric softener.
Do not exceed the maximum fi ll line. Using
too much fabric softener may result in stained
clothes.
Dilute concentrated fabric softeners with warm
water. Do not exceed the maximum fi ll line.
Never pour fabric softener directly onto the load
or into the drum.
Designed specially to use only
HE (High-Effi ciency) detergent
16
H OW TO U S E
CONTROL PANEL FEATURES
POWER ON/OFF BUTTON
Press to turn the washer ON.
Press again to turn the washer OFF.
NOTE: Pressing the ON/OFF button during a
cycle will cancel that cycle and any load settings
will be lost.
CYCLE SELECTOR KNOB
Turn this knob to select the desired cycle. Once
the desired cycle has been selected, the standard
presets will be shown in the display. These
settings can be adjusted using the cycle setting
buttons anytime before starting the cycle.
START/PAUSE BUTTON
Press this button to START the selected cycle.
If the washer is running, use this button to PAUSE
the cycle without losing the current settings.
NOTE: If you do not press the START/PAUSE
button within 4 minutes of selecting a cycle, the
washer automatically turns off.
1
2
CYCLE SETTING BUTTONS
Use these buttons to select the desired cycle
options for the selected cycle. Press the button
for that setting until the indicator light for the
desired value is lit.
OPTION BUTTONS
The option buttons allow you to select
additional cycle options and will light when
selected. Certain buttons also allow you to
activate special functions by pressing and
holding the button for 3 seconds.
For detailed information about the individual
options, please see the following pages.
LED DISPLAY
The display shows the settings, estimated
time remaining, options, and status messages
for your washer. The display will remain on
through the cycle.
4
5
3
6
17
2
1
3
6
5 4
H OW TO U S E
CYCLE GUIDE
NOTE: To protect your garments, not every wash/rinse temperature, spin speed, or option is available with every cycle.
The cycle guide below shows the options and recommended fabric types for each cycle.
Cycle Fabric type
Wash/Rinse
Temp.
Spin
Water
Plus
Stain
Cycle
Dry
18
SANITARY
MEDIUM
HIGH
NO SPIN
LOW
Heavily soiled
underwear, work
clothes, diapers, etc
EXTRA HOT/COLD
MEDIUM
NO SPIN
LOW
WARM/COLD
WARM/WARM
HOT/COLD
COLD/COLD
BULKY/LARGE
Large items such as
blankets and comforters
MEDIUM
HIGH
NO SPIN
LOW
PERM. PRESS
Dress shirts/pants,
wrinkle free clothing,
poly/cotton blend
clothing, table cloths
WARM/COLD
WARM/WARM
HOT/COLD
COLD/COLD
HIGH
EX HIGH
NO SPIN
LOW
MEDIUM
WARM/COLD
WARM/WARM
HOT/COLD
COLD/COLD
COTTON/
NORMAL
Cotton, linen, towels,
shirts, sheets, jeans,
mixed loads
MEDIUM
HIGH
NO SPIN
LOW
EXTRA HOT/COLD
HOT/COLD
BABY WEAR
MEDIUM
NO SPIN
LOW
COLD/COLD
WARM/COLD
WARM/WARM
DELICATES
Dress shirts/blouses
nylons, sheer or lacy
garments
MEDIUM
NO SPIN
LOW
COLD/COLD
WARM/COLD
WARM/WARM
HAND WASH/
WOOL
Items labeled
"hand washable"
EX HIGH
NO SPIN
LOW
MEDIUM
HIGH
HOT/COLD
COLD/COLD
WARM/COLD
WARM/WARM
SPEED
WASH
Lightly soiled clothing
and small loads
Pre-
Wash
Rinse+
Spin
Extra
Rinse
EX HIGH
NO SPIN
LOW
MEDIUM
HIGH
DRAIN + SPIN
Lightly soiled baby wear
Drain, Spin Only
= Available option = Cycle default settings
H OW TO U S E
THE LED DISPLAY
CYCLE COMPLETION INDICATOR
This portion of the display shows which stage of
the wash cycle is currently underway
(WASH, RINSE, SPIN or DRY).
ESTIMATED TIME REMAINING
When the START/PAUSE button is pressed, the
washer automatically detects the wash load
(weight) and optimizes the washing time, based
on the selected cycle and options. The display
will then indicate the estimated time remaining
for the selected wash cycle.
NOTE: The cycle time displayed may appear
much longer than that of a top-loading washer.
The displayed time is for the complete cycle,
rather than just the agitation portion of the cycle,
as is typically shown on a top-loading washer.
1
2
DOOR LOCK INDICATOR
Indicates that the door is locked. The washer
door will lock while the washer is operating. The
door can be unlocked by pressing the START/
PAUSE button to stop the washer.
NOTE: If the temperature in the washer is too
high, the door cannot be unlocked until the
washer has cooled. If the water level is too
high, select the DRAIN & SPIN cycle to drain
excess water. Do not try to force open the door.
CHILD LOCK INDICATOR
This indicator shows that the washer has
been set for CHILD LOCK. Select this function
to lock the buttons on the control panel and to
prevent tampering.
3
4
The LED display shows the settings, estimated time remaining, options, and status messages
for your washer. When the washer is turned on, the display will illuminate.
19
4
3
2
1
H OW TO U S E
OPERATING THE WASHER
Press the ON/OFF button to turn on the
washer. The lights around the
cycle selector knob will illuminate.
Turn the cycle selector knob to the desired
cycle. The display will show the
preset Rinse/Wash Temperature,
Spin Speed, and Option settings
for that cycle.
If you would like to change the settings for
that cycle, press the appropriate cycle set-
tings button(s) until the indicator light for the
desired setting is lit.
NOTE: To protect your garments, not every
wash/rinse temperature, spin speed, or op-
tion is available with every cycle.
1
2
3
Once you have loaded the washer and added
laundry products (detergent, bleach, and/or
fabric softener):
Press the START/PAUSE button
to begin the cycle. The door will
latch, the display will change,
and the washer will calculate the
estimated time remaining. Once the washer
has calculated the estimated total cycle time,
the washer will start. To pause the cycle at
any time, press PAUSE.
NOTE: The cycle time displayed may
appear much longer than that of a top-
loading washer. The displayed time is for the
complete cycle, rather than just the agitation
portion of the cycle, as is typically shown on
a top-loading washer.
NOTE: If the temperature in the washer is
too high, the door cannot be unlocked until
the washer has cooled. If the water level is
too high, select the DRAIN & SPIN cycle to
drain excess water. Do not try to force the
door open.
Washing time can be reduced significantly
for small or lightly soiled loads by selecting
the Speed Wash cycle and setting the Soil
Level button to Light.
When the load is finished, the beeper (if set)
will sound and the door will unlock.
Remove damp clothes from the washer
immediately. Check under the door seal
for small items.
4
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108

LG WM3455HW Le manuel du propriétaire

Catégorie
Machines à laver
Taper
Le manuel du propriétaire