Ariston AR6L 85 EX.M Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
GB
1
English, 1
Contents
Installation, 2-3
Unpacking and levelling
Connecting the electricity and water supplies
The first wash cycle
Technical data
Care and maintenance, 4
Cutting off the water or electricity supply
Cleaning the washing machine
Cleaning the detergent dispenser drawer
Caring for the door and drum of your appliance
Cleaning the pump
Checking the water inlet hose
Precautions and tips, 5
General safety
Disposal
Description of the washing machine
and starting a wash cycle, 6-7
Control panel
Indicator lights
Starting a wash cycle
Wash cycles, 8
Table of wash cycles
Personalisation, 9
Setting the temperature
Setting the spin speed
Functions
Detergents and laundry, 10
Detergent dispenser drawer
Bleach cycle
Preparing the laundry
Garments requiring special care
Load balancing system
Troubleshooting, 11
Service, 12
GB
AR6L 85
Instructions for use
WASHING MACHINE
FR
Français,13
AR
, 25
2
GB
Installation
! This instruction manual should be kept in a safe
place for future reference. If the washing machine
is sold, transferred or moved, make sure that the
instruction manual remains with the machine so
that the new owner is able to familiarise himself/
herself with its operation and features.
! Read these instructions carefully: they contain
vital information relating to the safe installation
and operation of the appliance.
Unpacking and levelling
Unpacking
1. Remove the washing machine from its packaging.
2. Make sure that the washing machine has not
been damaged during the transportation process.
If it has been damaged, contact the retailer and do
not proceed any further with the installation process.
3. Remove the 3 pro-
tective screws (used
during transportation)
and the rubber washer
with the corresponding
spacer, located on the
rear part of the applian-
ce (see figure).
4. Close off the holes using the plastic plugs
provided.
5. Keep all the parts in a safe place: you will need
them again if the washing machine needs to be
moved to another location.
! Packaging materials should not be used as
toys for children.
Levelling
1. Install the washing
machine on a flat stur-
dy floor, without resting
it up against walls,
furniture cabinets or
anything else.
2. If the floor is not
perfectly level, com-
pensate for any une-
venness by tightening
or loosening the adjustable front feet (see figure);
the angle of inclination, measured in relation to
the worktop, must not exceed 2°.
Levelling the machine correctly will provide it with
stability, help to avoid vibrations and excessive
noise and prevent it from shifting while it is ope-
rating. If it is placed on carpet or a rug, adjust the
feet in such a way as to allow a sufficient venti-
lation space underneath the washing machine.
Connecting the electricity and wa-
ter supplies
Connecting the water inlet hose
1. Connect the supply
pipe by screwing it to
a cold water tab using
a ¾ gas threaded con-
nection (see figure).
Before performing the
connection, allow the
water to run freely until
it is perfectly clear.
2. Connect the inlet
hose to the washing
machine by screwing
it onto the correspon-
ding water inlet of the
appliance, which is si-
tuated on the top right-
hand side of the rear
part of the appliance
(see figure).
3. Make sure that the hose is not folded over
or bent.
! The water pressure at the tap must fall within
the values indicated in the Technical details table
(see next page).
! If the inlet hose is not long enough, contact a
specialised shop or an authorised technician.
! Never use second-hand hoses.
! Use the ones supplied with the machine.
GB
3
Connecting the drain hose
Connect the drain
hose, without bending
it, to a drainage duct or
a wall drain located at a
height between 65 and
100 cm from the floor;
alternatively, rest it on
the side of a washba-
sin or bathtub, faste-
ning the duct supplied
to the tap (see figure).
The free end of the
hose should not be
underwater.
! We advise against the use of hose extensions;
if it is absolutely necessary, the extension must
have the same diameter as the original hose and
must not exceed 150 cm in length.
Electrical connections
Before plugging the appliance into the electricity
socket, make sure that:
•the socket is earthed and complies with all
applicable laws;
•thesocketisabletowithstandthemaximum
power load of the appliance as indicated in the
Technical data table (see opposite);
thepowersupplyvoltagefallswithinthevalues
indicated in the Technical data table (see opposite);
•thesocketiscompatiblewiththeplugofthe
washing machine. If this is not the case, repla-
ce the socket or the plug.
! The washing machine must not be installed
outdoors, even in covered areas. It is extremely
dangerous to leave the appliance exposed to
rain, storms and other weather conditions.
! When the washing machine has been installed,
the electricity socket must be within easy reach.
! Do not use extension cords or multiple sockets.
! The cable should not be bent or compressed.
! The power supply cable must only be replaced
by authorised technicians.
Warning! The company shall not be held responsible
in the event that these regulations are not respected.
The first wash cycle
Once the appliance has been installed, and
before you use it for the first time, run a wash
cycle with detergent and no laundry, using the
wash cycle 2.
65 - 100 cm
Technical data
Model
AR6L 85
Dimensions
width 59.5 cm
height 85 cm
depth 51,6 cm
Capacity
from 1 to 6 kg
Electrical
connections
please refer to the technical
data plate fixed to the ma-
chine
Water con-
nections
maximum pressure
1 MPa (10 bar)
minimum pressure
0.05 MPa (0.5 bar)
drum capacity 40 litres
Spin speed
up to 800 rotations per
minute
Test wash
cycles in
accordance
with re-
gulations
1061/2010
1015/2010
programme 2; Cotton Stan-
dard 60°.
programme 3; Cotton Stan-
dard 40°.
This appliance conforms to
the following EC Directives:
- 2004/108/EC (Electroma-
gnetic Compatibility)
- 2006/95/EC (Low Voltage)
- 2012/19/EU (WEEE)
4
GB
Care and maintenance
Cutting off the water and electricity
supplies
•Turnoffthewatertapaftereverywashcycle.
This will limit wear on the hydraulic system in-
side the washing machine and help to prevent
leaks.
•Unplugthewashingmachinewhencleaningit
and during all maintenance work.
Cleaning the washing machine
The outer parts and rubber components of the
appliance can be cleaned using a soft cloth
soaked in lukewarm soapy water. Do not use
solvents or abrasives.
Cleaning the detergent dispenser
drawer
Remove the dispenser
by raising it and pulling
it out (see figure).
Wash it under running
water; this operation
should be repeated
frequently.
Caring for the door and drum of
your appliance
•Alwaysleavetheportholedoorajarinorderto
prevent unpleasant odours from forming.
Cleaning the pump
The washing machine is fitted with a self-clea-
ning pump which does not require any mainte-
nance. Sometimes, small items (such as coins
or buttons) may fall into the pre-chamber which
protects the pump, situated in its bottom part.
! Make sure the wash cycle has finished and
unplug the appliance.
To access the pre-chamber:
1. using a screwdriver,
remove the cover pa-
nel on the lower front
part of the washing
machine (see figure);
2. unscrew the lid by
rotating it anti-clockwi-
se (see figure): a little
water may trickle out.
This is perfectly nor-
mal;
3. clean the inside thoroughly;
4. screw the lid back on;
5. reposition the panel, making sure the hooks
are securely in place before you push it onto the
appliance.
Checking the water inlet hose
Check the inlet hose at least once a year. If there
are any cracks, it should be replaced immedia-
tely: during the wash cycles, water pressure is
very strong and a cracked hose could easily
split open.
! Never use second-hand hoses.
1
2
GB
5
! This washing machine was designed and constructed in
accordance with international safety regulations. The fol-
lowing information is provided for safety reasons and must
therefore be read carefully.
General safety
• Thisappliancewasdesignedfordomesticuseonly.
This appliance can be used by children aged
from 8 years and above and persons with re-
duced physical, sensory or mental capabilities
or lack of experience and knowledge if they
have been given supervision or instruction
concerning use of the appliance in a safe way
and understand the hazards involved. Children
shall not play with the appliance. Cleaning and
user maintenance shall not be made by children
without supervision.
• Donottouchthemachinewhenbarefootorwithwetor
damp hands or feet.
• Donotpullonthepowersupplycablewhenunplugging
the appliance from the electricity socket. Hold the plug and
pull.
• Do not open the detergent dispenser drawer while the
machine is in operation.
• Donottouchthedrainedwaterasitmayreachextremely
high temperatures.
Neverforcetheportholedoor.Thiscoulddamagethesafety
lock mechanism designed to prevent accidental opening.
• Iftheappliancebreaksdown,donotunderanycircum-
stances access the internal mechanisms in an attempt to
repair it yourself.
• Alwayskeepchildrenwellawayfromtheappliancewhile
it is operating.
• Thedoorcanbecomequitehotduringthewashcycle.
• Iftheappliancehastobemoved,workinagroupoftwo
or three people and handle it with the utmost care. Never
try to do this alone, because the appliance is very heavy.
• Beforeloadinglaundry intothewashingmachine,make
sure the drum is empty.
Disposal
•Disposingofthepackagingmaterials:observelocalregu-
lations so that the packaging may be re-used.
•TheEuropeanDirective2012/19/EU-WEEEonWasteElec-
trical and Electronic Equipment, requires that old household
electrical appliances must not be disposed of in the normal
unsorted municipal waste stream. Old appliances must be
collected separately in order to optimise the recovery and
recycling of the materials they contain and reduce the impact
on human health and the environment. The crossed out
“wheeled bin” symbol on the product reminds you of your
obligation, that when you dispose of the appliance it must
be separately collected. Consumers should contact their local
authority or retailer for information concerning the correct
disposal of their old appliance.
Consumers should contact their local authority or
retailer for information concerning the correct
disposal of their old appliance.
Precautions and tips
6
GB
Detergent dispenser drawer: used to dispense
detergents and washing additives (see “Detergents and
laundry”).
There is a key which provides a summary of the available
wash cycles inside the detergent dispenser drawer; this
may be consulted at any time.
ON/OFF button: switches the washing machine on and
off.
WASH CYCLE knob: programmes the wash cycles. Du-
ring the wash cycle, the knob does not move.
FUNCTION buttons with indicator light: used to select the
available functions. The indicator light corresponding to the
selected function will remain lit.
TEMPERATURE knob: sets the temperature or the cold
wash cycle (see “Personalisation”).
SPIN SPEED knob: sets the spin speed or exclude the
spin cycle completely (see “Personalisation”).
WASH CYCLE PROGRESS/DELAY TIMER
indicator
light
s: used to monitor the progress of the wash cycle.
The illuminated indicator light shows which phase is in
progress.
If the Delay Timer function has been set, the time remai-
ning until the wash cycle starts will be indicated (see next
page).
DOOR LOCKED indicator light: indicates whether the
door may be opened or not (see next page).
START/PAUSE button with indicator light: starts or tem-
porarily interrupts the wash cycles.
N.B. To pause the wash cycle in progress, press this
button; the corresponding indicator light will flash orange,
while the indicator light for the current wash cycle phase
will remain lit in a fixed manner. If the DOOR LOCKED
indicator light is switched off, the door may be opened.
To start the wash cycle from the point at which it was inter-
rupted, press this button again.
Standby mode
This washing machine, in compliance with new energy sa-
ving regulations, is fitted with an automatic standby system
which is enabled after about 30 minutes if no activity is
detected. Press the ON-OFF button briefly and wait for the
machine to start up again.
Description of the washing
machine and starting a wash cycle
TEMPERATURE
knob
Detergent dispenser drawer
WASH CYCLE PROGRESS/
DELAY TIMER indicator lights
FUNCTION
buttons with
indicator lights
ON/OFF
button
SPIN SPEED
knob
DOOR
LOCKED
indicator light
START/PAUSE
button with indicator
light
Control panel
WASH CYCLE
knob
GB
7
Indicator lights
The indicator lights provide important information.
This is what they can tell you:
Delayed start
If the DELAY TIMER function has been activated (see “Per-
sonalisation”), after the wash cycle has been started the
indicator light corresponding to the selected delay period
will begin to flash:
As time passes, the remaining delay will be displayed and
the corresponding indicator light will flash:
Once the set delay has elapsed, the flashing indicator light
will switch off and the selected wash cycle will begin.
Wash cycle phase indicator lights
Once the desired wash cycle has been selected and has be-
gun, the indicator lights switch on one by one to indicate which
phase of the cycle is currently in progress.
Function buttons and corresponding indicator
lights
When a function is selected, the corresponding indicator
light will illuminate.
If the selected function is not compatible with the program-
med wash cycle, the corresponding indicator light will flash
and the function will not be activated.
If a function which is incompatible with another function
selected previously, only the most recent selection will
remain active.
Door locked indicator light
If this indicator light is on, the appliance door is locked to
prevent it from being opened accidentally; to avoid any
damage, wait for the indicator light to switch off before you
open the appliance door.
N.B. If the DELAY TIMER function is activated, the door
cannot be opened; pause the machine by pressing the
START/PAUSE button if you wish to open it.
! If the START/PAUSE indicator light (orange) flashes
rapidly at the same time as the function indicator light, this
indicates a problem has occurred (see “Troubleshooting”).
Starting a wash cycle
1. Turn the washing machine on by pressing the ON/OFF button. All the indicator lights will turn on for a few seconds, then only
the indicator lights relative to the selected programme settings will remain lit and the START/PAUSE indicator light will flash.
2. Load the laundry and close the door.
3. Set the WASH CYCLE knob to the desired programme.
4. Set the washing temperature (see “Personalisation”).
5. Set the spin speed (see “Personalisation”).
6. Measure out the detergent and washing additives (see “Detergents and laundry”).
7. Select the desired functions.
8. Start the wash cycle by pressing the START/PAUSE button and the corresponding indicator light will remain lit in a fixed
manner, in green.
To cancel the set wash cycle, pause the machine by pressing the START/PAUSE button and select a new cycle.
9. At the end of the wash cycle the indicator light will switch on. The DOOR LOCKED indicator light will switch off, indicating
that the door may be opened. Take out your laundry and leave the appliance door ajar to make sure the drum dries completely.
Switch the washing machine off by pressing the ON/OFF button.
Wash
Rinse
Spin
Drain
End of wash cycle
8
GB
Wash cycles
Table of wash cycles
The length of cycle shown on the display or in this booklet is an estimation only and is calculated assuming standard working conditions. The actual duration can vary accor-
ding to factors such as water temperature and pressure, the amount of detergent used, the amount and type of load inserted, load balancing and any wash options selected.
1) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 2 with a temperature of 60°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 60°C. The actual washing temperature may differ from the indicated value.
2) Test wash cycle in compliance with regulation 1061/2010: set wash cycle 3 with a temperature of 40°C.
This cycle is designed for cotton loads with a normal soil level and is the most efficient in terms of both electricity and water consumption; it should
be used for garments which can be washed at 40°C. The actual washing temperature may differ from the indicated value.
For all Test Institutes:
2) Long wash cycle for cottons: set wash cycle 3 with a temperature of 40°C.
3) Synthetic program along: set wash cycle 5 with a temperature of 40°C.
Cotton Standard 20° (wash cycle 4). Ideal for lightly soiled cotton loads. The effective performance levels achieved at cold
temperatures, which are comparable to washing at 40°, are guaranteed by a mechanical action which operates at varying
speed, with repeated and frequent peaks.
Mix 30’ (wash cycle 6) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 30 minutes and the-
refore saves both energy and time. By selecting this wash cycle (6 at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 3 kg.
Mix 15’(wash cycle 7) this wash cycle was designed to wash lightly soiled garments quickly: it lasts just 15 minutes and the-
refore saves both energy and time. By selecting this wash cycle (7 at 30°C), it is possible to wash different fabrics together
(except for wool and silk items), with a maximum load of 1.5 kg.
Sanitizing cycle (wash cycle 8). A high-temperature hygienic wash cycle (over 60°C) which requires the use of bleach. Pour
the bleach, the detergent and the additives into the relevant compartments (see paragraph entitled “Detergent dispenser
drawer”).
Goodnigt cycle (wash cycle 9). This is a silent cycle which can be run at night, when the electricity prices are lower. The
wash cycle is designed for cottons and synthetics. At the end of the cycle the machine stops while there is still water in the
drum; to spin and drain the laundry press the START/PAUSE button; alternatively the machine will perform the spin cycle and
drain the water automatically after 8 hours.
Baby cycle (wash cycle 10). This wash cycle can be used to remove the soiling typically caused by babies, while ensuring
that all detergent is removed from nappies in order to prevent the delicate skin of babies from suffering allergies. The cycle
has been designed to reduce the amount of bacteria by using a greater quantity of water and optimising the effect of special
disinfecting additives added to the detergent.
Wash cycles
Description of the wash cycle
Max.
temp. (°C)
Max.
speed
(rpm)
Detergents
Max. load
(kg)
Residual
dampness%
Energy con-
sumptionkWh
Total water lt
Cycle dura-
tion
Prewash
Bleach
Wash
Fabric
softener
1
Cotton + Prewash: extremely soiled whites.
90° 800
-
6 - - - 150’
2
Cotton Standard 60° (1): heavily soiled whites and resistant colours.
60° 800 - -
6 71 1,06 50 230
3
Cotton Standard 40° (2): lightly soiled resistant and delicate colours.
40° 800 - -
6 71 1,03 66 215
4
Cotton Standard 20°: lightly soiled resistant and delicate colours.
20° 800 - -
6 - - - 170’
5
Synthetics: heavily soiled resistant colours.
60° 800 - -
3 44
0,70 46 145’
5
Synthetics (3): lightly soiled resistant colours.
40° 800 - -
3 - - - 130’
6
Mix 30': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 - -
3 71 0,16 39 30’
7
Mix 15': to refresh lightly soiled garments quickly (not suitable for
wool, silk and clothes which require washing by hand).
30° 800 - -
1,5 71 0,13 29 15’
8
Sanitizing cycle: extremely soiled whites.
90° 800 -
6 - - - 165’
9
Goodnigt cycle: lightly soiled delicate colours.
40° 800 - -
4 - - - 280’
10
Baby cycle: heavily soiled delicate colours.
40° 800 - -
3 - - - 140’
11
Shirts
40° 600 - -
2 - - - 80’
12
Silk/Curtains: for garments in silk and viscose, lingerie.
30° 0 - -
1 - - - 55’
13
Wool: for wool, cashmere, etc.
40° 800 - -
1 - - - 65’
A
Rinse
- 800 - - -
6 - - - 36’
B
Spin
- 800 - - - - 6 - - - 10’
C
Drain
- 0 - - - - 6 - - - 3’
GB
9
Setting the temperature
Turn the TEMPERATURE knob to set the wash temperature (see Table of wash cycles).
The temperature may be lowered, or even set to a cold wash ( ).
The washing machine will automatically prevent you from selecting a temperature which is higher than the maximum value
set for each wash cycle.
Setting the spin speed
Turn the SPIN SPEED knob to set the spin speed for the selected wash cycle.
The maximum spin speeds available for each wash cycle are as follows:
Wash cycles Maximum spin speed
Cottons 800 rpm
Synthetics 800 rpm
Wool 800 rpm
Silk drain only
The spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .
The washing machine will automatically prevent you from selecting a spin speed which is higher than the maximum speed
set for each wash cycle.
Functions
The various wash functions available with this washing machine will help to achieve the desired results, every time.
To activate the functions:
1. Press the button corresponding to the desired function;
2. the function is enabled when the corresponding indicator light is illuminated.
Note:
- If the selected function is not compatible with the programmed wash cycle, the corresponding indicator light will flash and
the function will not be activated.
- If a function which is incompatible with another function selected previously, only the most recent selection will remain active.
Super Wash
Because a greater quantity of water is used in the initial phase of the cycle, and because of the increased cycle duration, this
function offers a high-performance wash.
Extra rinse
By selecting this function, the efficiency of the rinse is increased and optimal detergent removal is guaranteed. It is particularly
useful for sensitive skin.
Easy iron
By selecting this function, the wash and spin cycles will be modified in order to reduce the formation of creases.
At the end of the cycle the washing machine will perform slow rotations of the drum; the EASY IRON and START/PAUSE in-
dicator lights will flash (orange) and the phase will remain lit in a fixed manner. To end the cycle, press the START/PAUSE
button or the EASY IRON button.
For the Silk wash cycle, the machine will end the cycle while the laundry is soaking and the EASY IRON and START/PAUSE
indicator lights will flash (orange) and the RINSE phase will remain lit in a fixed manner. To drain the water so that the laundry
may be removed, press the START/PAUSE button or the EASY IRON button.
Delay timer
This timer delays the start time of the wash cycle by up to 12 hours.
Press the button repeatedly until the indicator light corresponding to the desired delay time switches on. The fifth time the button
is pressed, the function will be disabled.
N.B. Once you have pressed the START/PAUSE button, the delay time may only be decreased if you wish to modify it.
Personalisation
10
GB
Detergents and laundry
Detergent dispenser drawer
Good washing results also depend on the correct dose of
detergent: adding too much detergent will not necessarily
result in a more efficient wash, and may in fact cause build
up on the inside of your appliance and contribute to envi-
ronmental pollution.
! Use powder detergent for white cotton garments, for pre-
washing, and for washing at temperatures over 60°C.
! Follow the instructions given on the detergent packaging.
! Do not use hand washing detergents because these create
too much foam.
Open the detergent dispen-
ser drawer and pour in the
detergent or washing additi-
ve, as follows.
compartment 1: Pre-wash detergent (powder)
Before pouring in the detergent, make sure that extra com-
partment 4 has been removed.
compartment 2: Detergent for the wash cycle
(powder or liquid)
Liquid detergent should only be poured in immediately
prior to the start of the wash cycle.
compartment 3: Additives (fabric softeners, etc.)
The fabric softener should not overflow the grid.
extra compartment 4: Bleach
Bleach cycle
Bleaching may only be performed in conjunction with wash
cycles 8.
Pour the bleach into extra compartment 3; pour the detergent
and softener into the corresponding compartments, then
select one of the abovementioned wash cycles.
This option is recommended only for very soiled cotton
garments.
Preparing the laundry
•Dividethelaundryaccordingto:
- the type of fabric/the symbol on the label
- the colours: separate coloured garments from whites.
•Emptyallgarmentpocketsandcheckthebuttons.
• Donotexceedthelistedvalues,whichrefertotheweight
of the laundry when dry: see “Table of wash cycles”.
How much does your laundry weigh?
1 sheet 400-500 g
1 pillow case 150-200 g
1 tablecloth 400-500 g
1 bathrobe 900-1200 g
1 towel 150-250 g
Garments requiring special care
Shirts: use special wash cycle 11 to wash shirts in various
fabrics and colours.
It guarantees maximum care is taken of the garments and
minimises the formation of creases.
Silk: use special wash cycle 12 to wash all silk garments.
We recommend the use of special detergent which has
been designed to wash delicate clothes.
Curtains: fold curtains and place them in a pillow case or
mesh bag. Use wash cycle 12.
Wool: all wool garments can be washed using programme
13, even those carrying the “hand-wash only” label.
For best results, use special detergents and do not exceed
1 kg of laundry.
Load balancing system
Before every spin cycle, to avoid excessive vibrations and
to distribute the load in a uniform manner, the drum rotates
continuously at a speed which is slightly greater than the
washing rotation speed. If, after several attempts, the load
is not balanced correctly, the machine spins at a reduced
spin speed. If the load is excessively unbalanced, the
washing machine performs the distribution process instead
of spinning. To encourage improved load distribution and
balance, we recommend small and large garments are
mixed in the load.
M
AX
1
2
4
3
GB
11
Troubleshooting
Your washing machine could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure
that the problem cannot be not solved easily using the following list.
Problem:
The washing machine does not
switch on.
The wash cycle does not start.
The washing machine does not
take in water (the indicator light for
the first wash cycle stage flashes
rapidly).
The washing machine continuously
takes in and drains water.
The washing machine does not
drain or spin.
The washing machine vibrates a lot
during the spin cycle.
The washing machine leaks.
The START/PAUSE indicator light
(orange) and the function indicator
lights flash rapidly.
There is too much foam.
Possible causes / Solutions:
• Theapplianceisnotpluggedintothesocketfully,orisnotmakingcontact.
• Thereisnopowerinthehouse.
• Thewashingmachinedoorisnotclosedproperly.
• TheON/OFFbuttonhasnotbeenpressed.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thewatertaphasnotbeenopened.
• Adelayedstarthasbeenset(see “Personalisation”).
• Thewaterinlethoseisnotconnectedtothetap.
• Thehoseisbent.
• Thewatertaphasnotbeenopened.
• Thereisnowatersupplyinthehouse.
• Thepressureistoolow.
• TheSTART/PAUSEbuttonhasnotbeenpressed.
• Thedrainhoseisnotfittedataheightbetween65and100cmfromthefloor
(see “Installation”).
• Thefreeendofthehoseisunderwater(see “Installation”).
• Thewalldrainagesystemisnotfittedwithabreatherpipe.
If the problem persists even after these checks, turn off the water tap, switch
the appliance off and contact the Assistance Service. If the dwelling is on one of
the upper floors of a building, there may be problems relating to water drainage,
causing the washing machine to fill with water and drain continuously. Special
anti-draining valves are available in shops and help to avoid this inconvenience.
• Thewashcycledoesnotincludedraining:somewashcyclesrequirethedrain
phase to be started manually.
• TheEASYIRONfunctionhasbeenactivated:Tocompletethewashcycle,
press the START/PAUSE button (“Personalisation”).
• Thedrainhoseisbent(see “Installation”).
• Thedrainageductisclogged.
• Thedrumwasnotunlockedcorrectlyduringinstallation(see “Installation”).
• Thewashingmachineisnotlevel(see “Installation”).
Thewashingmachineistrappedbetweencabinetsandwalls(see “Installation”).
• Thewaterinlethoseisnotscrewedonproperly(see “Installation”).
• Thedetergentdispenserdrawerisblocked(forcleaninginstructions,see “Care
and maintenance”).
• Thedrainhoseisnotfixedproperly(see “Installation”).
• Switchoffthemachineandunplugit,waitforapproximately1minuteandthen
switch it back on again.
If the problem persists, contact the Technical Assistance Service.
• Thedetergentisnotsuitableformachinewashing(itshoulddisplaythetext
“for washing machines” or “hand and machine wash”, or the like).
• Toomuchdetergentwasused.
12
GB
Service
Before calling for Assistance:
• Check whether you can solve the problem alone (see “Troubleshooting”);
• Restarttheprogrammetocheckwhethertheproblemhasbeensolved;
• Ifthisisnotthecase,contactanauthorisedTechnicalAssistanceCentreusingthetelephonenumberprovidedonthe
guarantee certificate.
! Always request the assistance of authorised technicians.
Have the following information to hand:
• thetypeofproblem;
• theappliancemodel(Mod.);
• theserialnumber(S/N).
This information can be found on the data plate applied to the rear of the washing machine, and can also be found on the
front of the appliance by opening the door.
FR
13
Français
Sommaire
Installation, 14-15
Déballage et mise à niveau
Raccordements eau et électricité
Premier cycle de lavage
Caractéristiques techniques
Entretien et soin, 16
Coupure de l’arrivée d’eau et du courant
Nettoyage du lave-linge
Nettoyage du tiroir à produits lessiviels.
Entretien du hublot et du tambour
Nettoyage de la pompe
Contrôle du tuyau d’arrivée de l’eau
Précautions et conseils, 17
Sécurité générale
Mise au rebut
Description du lave-linge et démarrage
d’un programme, 18-19
Bandeau de commandes
Voyants
Démarrage d’un programme
Programmes, 20
Tableau des programmes
Personnalisations, 21
Sélection de la température
Sélection de l’essorage
Fonctions
Produits lessiviels et linge, 22
Tiroir à produits lessiviels
Cycle blanchissage
Triage du linge
Linge ou vêtements particuliers
Système d’équilibrage de la charge
Anomalies et remèdes, 23
Assistance, 24
FR
AR6L 85
Mode d’emploi
LAVE-LINGE
14
FR
Installation
! Conserver ce mode demploi pour pouvoir le con-
sulter à tout moment. En cas de vente, de cession
ou de dénagement, veiller à ce quil suive tou-
jours le lave-linge pour que son nouveau propriétaire
soit informé sur son mode de fonctionnement et
puisse profiter des conseils correspondants.
! Lire attentivement les instructions: elles fournis-
sent des conseils importants sur l’installation,
l’utilisation et la sécurité de l’appareil.
Déballage et mise à niveau
Déballage
1. Déballer le lave-linge.
2. Contrôler que le lave-linge n’a pas été endom-
mapendant le transport. S’il est abîmé, ne pas
le raccorder et contacter le vendeur.
3. Enlever les 3 vis
de protection servant
au transport, le ca-
outchouc et la cale,
placés dans la partie
arrière (voir figure).
4. Boucher les trous à l’aide des bouchons
plastique fournis.
5. Conserver toutes ces pièces: il faudra les
remonter en cas de transport du lave-linge.
! Les pièces d’emballage ne sont pas des jouets
pour enfants.
Mise à niveau
1. Installer le lave-linge sur un sol plat et rigide,
sans l’appuyer contre des murs, des meubles
ou autre.
2. Si le sol n’est pas
parfaitement horizon-
tal, visser ou dévisser
les pieds de réglage
avant (voir figure) pour
niveler l’appareil; son
angle dinclinaison,
mesuré sur le plan
de travail, ne doit pas
dépasser 2°.
Une bonne mise à niveau garantit la stabilité
de l’appareil et évite qu’il y ait des vibrations,
du bruit et des déplacements en cours de
fonctionnement. Si la machine est posée sur
de la moquette ou un tapis, régler les pieds de
manière à ce qu’il y ait suffisamment d’espace
pour assurer une bonne ventilation.
Raccordements eau et électricité
Raccordement du tuyau d’arrivée de l’eau
1. Relier le tuyau d’ali-
mentation en le vissant
à un robinet d’eau froi-
de à embout fileté 3/4
gaz (voir figure).
Faire couler leau ju-
squà ce quelle soit
limpide et sans impure-
tés avant de raccorder.
2. Raccorder le tuyau
d’arrivée de leau au
lave-linge en le vissant
à la prise d’eau prévue,
dans la partie arrière
en haut à droite (voir
figure).
3. Attention à ce que le tuyau ne soit pas plié
ou écrasé.
! La pression de l’eau doit être comprise entre
les valeurs indiquées dans le tableau des Ca-
ractéristiques techniques (voir page ci-contre).
! Si la longueur du tuyau d’alimentation ne suffit
pas, s’adresser à un magasin spécialisé ou à un
technicien agréé.
! N’utiliser que des tuyaux neufs.
! Utiliser ceux qui sont fournis avec l’appareil.
FR
15
65 - 100 cm
Raccordement du tuyau de vidange
Raccorder le tuyau
dévacuation, sans
le plier, à un conduit
d’évacuation ou à une
évacuation murale pla-
cés à une distance du
sol comprise entre 65
et 100 cm;
ou bien l’accrocher à
un évier ou à une bai-
gnoire, dans ce cas,
fixer le support en pla-
stique fourni avec l’ap-
pareil au robinet (voir
figure). L’extrémité libre
du tuyau d’évacuation
ne doit pas être plon-
gée dans l’eau.
! L’utilisation d’un tuyau de rallonge est abso-
lument conseillée mais si on ne peut faire
autrement, il faut absolument qu’il ait le même
diamètre que le tuyau original et sa longueur ne
doit pas dépasser 150 cm.
Branchement électrique
Avant de brancher la fiche dans la prise de cou-
rant, s’assurer que:
•lapriseestbienreliéeàlaterreetestconforme
aux réglementations en vigueur;
•lapriseestbienapteàsupporterlapuissan-
ce maximale de l’appareil indiquée dans le
tableau des Caractéristiques techniques (voir
ci-contre);
•la tension d’alimentation est bien comprise
entre les valeurs figurant dans le tableau des
Caractéristiques techniques (voir ci-contre);
•lapriseestbiencompatibleaveclafichedulave-
linge. Autrement, remplacer la prise ou la fiche.
! Le lave-linge ne doit pas être installé dehors,
même à l’abri, car il est très dangereux de le
laisser exposé à la pluie et aux orages.
! Après installation du lave-linge, la prise de
courant doit être facilement accessible.
! N’utiliser ni rallonges ni prises multiples.
! Le câble ne doit être ni plié ni trop écrasé.
! Le câble d’alimentation ne doit être remplacé
que par des techniciens agréés.
Attention! Nous déclinons toute responsabilité en cas
de non-respect des normes énumérées ci-dessus.
Premier cycle de lavage
Avant la première mise en service de l’appareil,
effectuer un cycle de lavage avec un produit
lessiviel mais sans linge et sélectionner le pro-
gramme 2.
Caractéristiques techniques
Modèle
AR6L 85
Dimensions
largeur 59,5 cm
hauteur 85 cm
profondeur 51,6 cm
Capacité
de 1 à 6 kg
Raccorde-
ments élec-
triques
Voir la plaque signalétique
appliquée sur la machine
Raccor-
dements
hydrauli-
ques
pression maximale 1 MPa
(10 bar) pression minimale
0,05 MPa (0,5 bar) capacité
du tambour 40 litres
Vitesse
d'essorage
jusqu'à 800 tours minute
Programmes
de contrôle
selon les
règlements
1061/2010
1015/2010
Programme 2;
Coton standard 60°C.
Programme 3;
Coton standard 40°C.
Cet appareil est conforme
aux Directives Communau-
taires suivantes:
- 2004/108/CE (Compatibili-
té électromagnétique)
- 2012/19/EU - WEEE
- 2006/95/CE (Basse Tension)
16
FR
Entretien et soin
Coupure de l’arrivée d’eau et du
courant
•Fermerlerobinetdel’eauaprèschaquelavage.
Cela réduit l’usure de l’installation hydraulique
du lave-linge et évite tout danger de fuites.
•Débrancherlafichedelaprisedecourantlors
de tout nettoyage du lave-linge et pendant tous
les travaux d’entretien.
Nettoyage du lave-linge
Pour nettoyer l’extérieur et les parties en caou-
tchouc, utiliser un chiffon imbibé d’eau tiède et
de savon. N’utiliser ni solvants ni abrasifs.
Nettoyage du tiroir à produits les-
siviels.
Soulever le tiroir et le
tirer vers soi pour le
sortir de son logement
(voir figure).
Le laver à l’eau cou-
rante; effectuer cette
opération assez sou-
vent.
Entretien du hublot et du tambour
•Ilfauttoujourslaisserlehublotentrouvertpour
éviter la formation de mauvaise odeurs.
Nettoyage de la pompe
Le lave-linge est équid’une pompe autonetto-
yante qui n’exige aucune opération d’entretien.
Il peut toutefois arriver que de menus objets
(pièces de monnaie, boutons) tombent dans la
préchambre qui protège la pompe, placée en
bas de cette dernière.
! S’assurer que le cycle de lavage est bien ter-
miné et débrancher la fiche.
Pour accéder à cette préchambre:
1. démonter le panne-
au sit à l’avant du
lave-linge à l’aide d’un
tournevis (voir figure);
2. dévisser le couver-
cle en le tournant dans
le sens inverse des
aiguilles d’une montre
(voir figure): il est nor-
mal qu’un peu d’eau
s’écoule;
3. nettoyer soigneusement l’intérieur;
4. revisser le couvercle;
5. remonter le panneau en veillant à bien enfiler
les crochets dans les fentes prévues avant de
le pousser contre l’appareil.
Contle du tuyau d’arrie de l’eau
Contrôler le tuyau d’alimentation au moins une
fois par an. Procéder à son remplacement en cas
de craquèlements et de fissures: car les fortes
pressions subies pendant le lavage pourraient
provoquer des cassures.
! N’utiliser que des tuyaux neufs.
1
2
FR
17
Précautions et conseils
! Ce lave-linge a été conçu et fabriqué conformément aux
normes internationales de sécurité. Ces consignes sont
fournies pour des raisons de sécurité, il faut les lire attenti-
vement.
Sécurité générale
•Cetappareilpeutêtreutiliséparlesenfantsà
partir de 8 ans et par les personnes dont les
capacités physiques, sensorielles ou mentales
sont réduites ou qui ne disposent pas des con-
naissances suffisantes, à condition qu’ils soient
encadrés ou aient été formés de façon appro-
pre pour l’utilisation de l’appareil de façon re
et en comprenant les dangers qui y sont liés.
Les enfants ne doivent pas jouer avec l’appareil.
Lentretien et le nettoyage ne doivent pas être
effects par les enfants sans surveillance.
• Cetappareilestconçupourunusagedomestique.
• Nejamaistoucherl’appareilsil’onestpiedsnusetsiles
mains sont mouillées ou humides.
• Nejamaistirersurlecâblepourdébrancherlafichedela
prise de courant.
• Nepasouvrirletiroiràproduitslessivielssilamachine
est branchée.
• Nepastoucheràl’eaudevidange,ellepeutatteindre
des températures très élevées.
• Nepasforcerpourouvrirlehublot:leverrouillagede
sécurité qui protège contre les ouvertures accidentelles
pourrait s’endommager.
• Encasdepanne,éviteràtoutprixd’accéderauxméca-
nismes internes pour tenter une réparation.
• Veilleràcequelesenfantsnes’approchentpasdel’ap-
pareil pendant son fonctionnement.
• Pendantlelavage,lehublotatendanceàseréchauffer.
• Deuxoutroispersonnessontcessairespourdéplacer
lappareil avec toutes les précautions nécessaires. Ne jamais
le placer tout seul car il est très lourd.
• Avantd’introduirelelinge,s’assurerqueletambourest
bien vide.
Mise au rebut
• Miseaurebutdumatérield’emballage:seconformeraux
réglementations locales de manière à ce que les embal-
lages puissent être recyclés.
• LaDirectiveEuropéenne2012/19/EU-WEEEsurles
Déchets des Equipements Electriques et Electroniques,
exige que les appareils ménagers usagés ne soient pas
jetés dans le flux normal des déchets municipaux. Les
appareils usagés doivent être collectés séparément afin
d’optimiser le taux de récupération et le recyclage des
matériaux qui les composent et réduire l’impact sur la
santé humaine et l’environnement.
Le symbole de la ‘’poubelle barrée’’ est apposée sur
tous les produits pour rappeler les obligations de collecte
séparée. Les consommateurs devront contacter les au-
torités locales ou leur revendeur concernant la démarche
à suivre pour l’enlèvement de leur vieil appareil.
18
FR
Tiroir à produits lessiviels: pour charger les produits
lessiviels et les additifs (voir “Produits lessiviels et linge”).
Touche ON/OFF: pour allumer ou éteindre le lave-linge.
Bouton PROGRAMMES: pour sélectionner les program-
mes. Pendant le programme, le bouton ne tournera pas.
Touches avec voyants FONCTION: pour sélectionner
les fonctions disponibles. Le voyant correspondant à la
fonction sélectionnée restera allumé.
Bouton TEMPÉRATURE: pour sélectionner la températu-
re ou un lavage à froid (voir “Personnalisations”).
Bouton ESSORAGE: pour sélectionner l’essorage ou le
supprimer (voir “Personnalisations”).
Voyants DÉROULEMENT CYCLE/DÉPART DIFFÉRÉ:
pour suivre le stade d’avancement du programme de
lavage.
Le voyant allumé indique la phase de lavage en cours.
Si la fonction “Départ différé” (départ différé) a été sélec-
tionnée, ils indiquent le temps restant jusqu’au démarrage
du programme (voir page ci-contre).
Voyant HUBLOT VERROUILLÉ: indique si la porte est
verrouillée (voir page ci-contre).
Touche avec voyant START/PAUSE: pour démarrer les
programmes ou les interrompre momentanément.
N.B.: pour effectuer une pause du lavage en cours, appu-
yer sur cette touche, le voyant correspondant se mettra à
clignoter en orange tandis que celui de la phase en cours
restera allumé fixe. Si le voyant HUBLOT VERROUILLÉ
est éteint, on peut ouvrir la porte (3 minutes environ).
Pour faire redémarrer le lavage exactement de l’endroit où
il a été interrompu, appuyer une nouvelle fois sur la touche.
Stand-by
Ce lave-linge, conformément aux nouvelles normes en
vigueur dans le domaine de l’économie d’énergie, est
équipée d’un système d’extinction automatique (veille)
activé après environ 30 minutes d’inutilisation. Appuyez
brièvement sur la touche
ON/OFF
et attendre que la ma-
chine soit réactivée.
Description du lave-linge et
démarrage d’un programme
Bouton
TEMPÉRATURE
Tiroir à produits lessiviels
Voyants DÉROULEMENT
CYCLE/DÉPART DIFFÉRÉ
Touches avec voyants
FONCTION
Touche ON/OFF
Bouton
ESSORAGE
Voyant
HUBLOT
VERROUILLÉ
Touche avec voyant
START/PAUSE
Bandeau de commandes
Bouton
PROGRAMMES
FR
19
Voyants
Les voyants fournissent des informations importantes.
Voilà ce qu’ils signalent:
Départ différé
Si la fonction “Départ différé” a été activée (voir “Personnali-
sations”), le voyant correspondant au temps sélectionné se
mettra à clignoter, après avoir lancé le programme :
Au fur et à mesure que le temps passe, le temps restant
est affiché avec clignotement du voyant correspondant.
Quand le temps sélectionné touche à sa fin, le voyant
clignotant s’éteint et le programme sélectionné démarre.
Voyants phase en cours
Une fois que le cycle de lavage sélectionné a démarré,
les voyants s’allument progressivement pour indiquer son
stade d’avancement:
Touches fonction et voyants correspondants
La sélection d’une fonction entraîne l’allumage du voyant
correspondant.
Si la fonction sélectionnée est incompatible avec le pro-
gramme sélectionné, le voyant correspondant se met à
clignoter et la fonction n’est pas activée.
En cas de sélection d’une fonction incompatible avec une
autre précédemment sélectionnée, la seule à être activée
sera celle choisie en dernier.
Voyant hublot verrouillé:
Le voyant allumé indique que le hublot est verrouillé pour
empêcher toute ouverture accidentelle. Pour éviter d’en-
dommager l’appareil, attendre que le voyant cesse de
clignoter avant d’ouvrir la porte (3 minutes environ).
N.B: si la fonction DÉPART DIFFÉRÉ est activée, le hublot
ne s’ouvre pas. Pour l’ouvrir il faut appuyer sur la touche
START/PAUSE qui met l’appareil en pause.
! Un clignotement rapide du voyant START/PAUSE (oran-
ge) simultané à celui des fonctions signale une anomalie
(voir “Anomalies et remèdes”).
Démarrage d’un programme
1. Allumer le lave-linge en appuyant sur la touche MARCHE/ARRET. Tous les voyants s’allumeront pendant quelques secon-
des, ne resteront ensuite allumés que les voyants correspondant aux sélections du programme en cours et le voyant START/
PAUSE se mettra à clignoter.
2. Charger le linge et fermer le hublot.
3. Sélectionner à l’aide du bouton PROGRAMMES le programme désiré.
4. Sélectionner la température de lavage (voir “Personnalisations”).
5. Sélectionner la vitesse d’essorage (voir “Personnalisations”).
6. Verser les produits lessiviels et les additifs (voir “Produits lessiviels et linge”).
7. Sélectionner les fonctions désirées.
8. Appuyer sur la touche START/PAUSE pour démarrer le programme, le voyant correspondant vert restera allumé en fixe.
Pour annuler le cycle sélectionné, appuyer sur la touche START/PAUSE pour placer l’appareil en pause et choisir un nouve-
au cycle.
9. A la fin du programme, le voyant s’allume. Le voyant HUBLOT VERROUILLÉ s’éteint pour signaler que le hublot peut
être ouvert (3 minutes environ). Sortir le linge et laisser le hublot entrouvert pour faire sécher le tambour.
Eteindre le lave-linge en appuyant sur la touche ON/OFF.
Lavage
Rinçage
Essorage
Vidange
Fin de Lavage
20
FR
Programmes
Tableau des programmes
Coton Standard 20° (programme 4). Idéal pour des charges de linge sale en coton. Les bonnes performances, même à froid,
comparables à celles d’un lavage à 40°, sont assurées grâce à une action mécanique qui brasse en variant la vitesse et avec
des pics répétés et rapprochés.
Mix 30’ (programme 6) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 30 minutes et per-
met ainsi de faire des économies d’énergie et de temps. La sélection de ce programme (6 à 30°C) permet de laver ensemble
des textiles différents (sauf laine et soie) en ne dépassant pas 3 kg de charge.
Mix 15’ (programme 7) spécialement conçu pour laver du linge peu sale en un rien de temps: il ne dure que 15 minutes et per-
met ainsi de faire des économies d’énergie et de temps. La sélection de ce programme (7 à 30°C) permet de laver ensemble
des textiles différents (sauf laine et soie) en ne dépassant pas 1,5 kg de charge.
Anti-bactérien (programme 8). Un programme hautes températures qui prévoit l’utilisation de produits javelisés à des tem-
pératures supérieures à 60°C. Pour blanchir, verser le produit javelisé, les lessives et les additifs dans les compartiments cor-
respondants (voir paragraphe “Tiroir à produits lessiviels”).
Bonne nuit (programme 9). C’est un cycle silencieux qui permet de faire fonctionner le lave-linge la nuit quand le tarif d’électri-
cité est plus bas. Ce programme est spécialement conçu pour les synthétiques et le coton. A la fin du cycle l’appareil s’arrête,
cuve pleine. Pour procéder à l’essorage et à la vidange, appuyer sur la touche START/PAUSE, à défaut, l’appareil procédera
automatiquement au bout de 8 heures à l’essorage et à la vidange de l’eau.
Bébé (programme 10). Programme spécial, idéal pour le lavage des vêtements d’enfants souvent très sales, il élimine toute
trace de lessive du linge pour protéger leur peau délicate et éviter tout risque d’allergie. Spécialement conçu pour diminuer la
charge bactérienne, ce cycle utilise une plus grande quantité d’eau et optimise l’effet des additifs désinfectants spécifiques
ajoutés à la lessive.
La durée du cycle indiquée sur l’écran ou dans la notice représente une estimation calculée dans des conditions standard. Le temps effectif peut varier en fonction de nombreux facteurs
tels que : température et pression de l’eau en entrée, température ambiante, quantité de lessive, quantité et type de charge, équilibrage de la charge, options supplémentaires sélectionnées.
1) Programme de contrôle selon la règlements 1061/2010: sélectionner le programme 2 et une température de 60°C.
Ce cycle convient au lavage d’une charge de coton normalement sale et c’est le plus performant en termes de consommation d’eau et d’énergie, l’utiliser pour du linge lavable à 60°C. La températu-
re effective de lavage peut différer de la température indiquée.
2) Programme de contrôle selon la règlements 1061/2010: sélectionner le programme 3 et une température de 40°C.
Ce cycle convient au lavage d’une charge de coton normalement sale et c’est le plus performant en termes de consommation d’eau et d’énergie, l’utiliser pour du linge lavable à 40°C. La températu-
re effective de lavage peut différer de la température indiquée.
Pour tous les instituts qui effectuent ces tests :
2) Programme coton long: sélectionner le programme 3 et une température de 40°C.
3) Programme synthétique long: sélectionner le programme 5 et une température de 40°C.
Programmes
Description du Programme
Temp.
maxi.
(°C)
Vitesse
maxi
(tours
minute)
Produits lessiviels
Charge maxi
(Kg)
Humidité
résiduelle %
Consomma-
tion d’énergie
kWh
Eau totale lt
Durée cycle
Prelavage
Javel
Lavage
Assouplis-
sant
1
Coton + Prelavage: blancs extrêmement sales.
90° 800
-
6 - - - 150’
2
Coton standard 60°C (1): blancs et couleurs résistantes ts sales.
60° 800 - -
6 71 1,06 50 230
3
Coton standard 40°C (2): blancs et couleurs délicates peu sales.
40° 800 - -
6 71 1,03 66 215
4
Coton standard 20°C: blancs et couleurs délicates peu sales.
20° 800 - -
6 - - - 170’
5
Synthétique: couleurs résistantes très sales.
60° 800 - -
3 44
0,70 46 145’
5
Synthétique (3): couleurs résistantes peu sales.
40° 800 - -
3 - - - 130’
6
MIX 30': pour rafraîchir rapidement du linge peu sale
(ne convient pas pour la laine, la soie et le linge à laver à la main).
30° 800 - -
3 71 0,16 39 30’
7
MIX 15': pour rafraîchir rapidement du linge peu sale
(ne convient pas pour la laine, la soie et le linge à laver à la main).
30° 800 - -
1,5 71 0,13 29 15’
8
Anti-bactérien: blancs extrêmement sales.
90° 800 -
 
6 - - - 165’
9
Bonne Nuit: couleurs délicates peu sales.
40° 800 - -
4 - - - 280’
10
Bébé: couleurs délicates très sales.
40° 800 - -
3 - - - 140’
11
Chemises
40° 600 - -
2 - - - 80’
12
Soie/Voilages 30°: pour linge en soie, viscose, lingerie.
30° 0 - -
1 - - - 55’
13
Laine 40°: pour laine, cachemire, etc.
40° 800 - -
1 - - - 65’
A
Rinçage
- 800 - - -
6 - - - 36’
B
Essorage
- 800 - - - - 6 - - - 10’
C
Vidange
- 0 - - - - 6 - - - 3’
1 / 1

Ariston AR6L 85 EX.M Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues