TEAC GF-650 Manuel utilisateur

9A10509700

Z

GF

-

650

Multi music player/CD recorder

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL USUARIO

ENGLISH

FRANÇAIS ESPAÑOL

IMPORTANT SAFETY INSTRUCTIONS

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions.

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance

with the manufacturer’s instructions.

8) Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that

produce heat.

9) Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided plug

does not fit into your outlet, consult an electrician for

replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched

particularly at plugs, convenience receptacles, and the point

where they exit from the apparatus.

11)Only use attachments/accessories specified by the

manufacturer.

12) Use only with the cart, stand, tripod,

bracket, or table specified by the

manufacturer, or sold with the

apparatus. When a cart is used, use

caution when moving the

cart/apparatus combination to avoid

injury from tip-over.

13)Unplug this apparatus during lightning storms or when

unused for long periods of time.

14) Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

such as power-supply cord or plug is damaged, liquid has

been spilled or objects have fallen into the apparatus, the

apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

<

Do not expose this apparatus to drips or splashes.

<

Do not place any objects filled with liquids, such as vases, on

the apparatus.

< Do not install this apparatus in a confined space such as a

book case or similar unit.

< The apparatus draws nominal non-operating power from the

AC outlet with its POWER switch in the off position.

< The apparatus should be located close enough to the AC

outlet so that you can easily grasp the power cord plug at any

time.

<

An apparatus with Class

!

construction shall be connected to

an AC outlet with a protective grounding connection.

< Batteries (battery pack or batteries installed) shall not be

exposed to excessive heat such as sunshine, fire or the like.

2

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated “dangerous voltage” within

the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to

persons.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in

the literature accompanying the appliance.

3

ENGLISH

Optical pickup :

Type : SF-W36FR

Manufacturer : SANYO ELECTRIC CO., LTD.

Laser output : Less than 1 mW (Play) on the objective lens

Less than 5 mW (Record) on the objective lens

Less than 10 mW (Erase) on the objective lens

Wavelength : 783 nm

This product has been designed and manufactured according to

FDA regulations “title 21, CFR, chapter 1, subchapter J, based on

the Radiation Control for Health and Safety Act of 1968“, and is

classified as class 1 laser product. There is not hazardous invisible

laser radiation during operation because invisible laser radiation

emitted inside of this product is completely confined in the

protective housings.

The label required in this regulation is shown

①.

For U.S.A.

①

CAUTION

<

DO NOT REMOVE THE EXTERNAL CASES OR CABINETS TO

EXPOSE THE ELECTRONICS. NO USER SERVICEABLE PARTS

ARE WITHIN!

<

IF YOU ARE EXPERIENCING PROBLEMS WITH THIS PRODUCT,

CONTACT TEAC FOR A SERVICE REFERRAL. DO NOT USE THE

PRODUCT UNTIL IT HAS BEEN REPAIRED.

<

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

WARNING: TO PREVENT FIRE OR SHOCK

HAZARD, DO NOT EXPOSE THIS APPLIANCE

TO RAIN OR MOISTURE.

This equipment has been tested and found to comply with the

limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate

radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful

interference to radio communications. However, there is no

guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to

try to correct the interference by one or more of the following

measures:

• Reorient or relocate the equipment and/or the receiving

antenna.

• Increase the separation between the equipment and

receiver.

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

for help.

CAUTION

Changes or modifications to this equipments not expressly

approved by TEAC CORPORATION for compliance will void the

user’s warranty.

For U.S.A.

CAUTION

The product shall not be exposed to dripping or splashing and

that no object filled with liquids, such as vases, shall be placed

on the product.

Do not install this equipment in a confined space such as a

book case or similar unit.

4

Contents

Thank you for choosing TEAC. Read this manual carefully

to get the best performance from this unit.

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Before using the unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Handling Records . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

How to Replace the Stylus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Discs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Remote Control Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

How to open/close the turntable cover . . . . . . . . . . . . . . . . . . . 8

Assembling the Turntable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Identifying the Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Listening to a Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Listening to the Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Listening to a CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Time Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Repeat Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Shuffle Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Programmed Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Before Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Finalize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Erase or Unfinalize a CD-RW . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Before using the unit

Read this before attempting any operations

<

The nominal temperature should be between 5°C and 35°C

(41°F and 95°F). The CD-RW recorder is more sensitive to

extremes of temperature than ordinary CD players.

<

Relative humidity should be 30 to 90 degrees noncondensing.

<

As the unit may become warm during operation, always leave

sufficient space around the unit for ventilation.

< The voltage supplied to the unit should match the voltage as

printed on the rear panel. If you are in any doubt regarding

this matter, consult an electrician.

<

Choose the installation location of your unit carefully. Avoid

placing it in direct sunlight or close to a source of heat. Also

avoid locations subject to vibrations and excessive dust, heat,

cold or moisture.

<

Do not place the unit on an amplifier/receiver.

<

Do not open the cabinet as this might result in damage to the

circuitry or electrical shock. If a foreign object should get into

the unit, contact your dealer or service company.

<

When removing the power plug from the wall outlet, always

pull directly on the plug, never yank the cord.

< To keep the laser pickup clean, do not touch it, and always

close the disc tray.

< Do not attempt to clean the unit with chemical solvents as

this might damage the finish. Use a clean, dry cloth.

< Keep this manual in a safe place for future reference.

DO NOT MOVE THE UNIT DURING PLAYBACK

During playback, the disc rotates at high speed. Do NOT lift or

move the unit during playback. Doing so may damage the

disc or the unit.

WHEN MOVING THIS UNIT

When changing the unit’s location or packing the unit for

moving, be sure to remove the record or disc. Moving this

unit with the record or disc loaded may result in damage to

this unit. If the unit is to be packed and moved a great

distance, see Page 9 for instructions.

5

ENGLISH

Handling Records

< Keep your records away from dust. Keep them in a cool, dry

place.

< To avoid dust and scratches, keep records in their sleeves and

jackets when not in use.

< Store records upright on their edges. Records stored

horizontally will eventually bend and warp.

< Do not expose records to direct sunlight or high humidity and

temperature. Long exposure to high temperatures will warp

the record.

<

Do not store your records in the trunk of your car. The

temperature in a closed trunk can ruin your collection.

< Store records in an area with stable temperature and

humidity.

< Should the record become dirty, gently wipe the surface in a

circular motion, using a soft anti-static cloth.

Commercial record cleaning systems are available from many

retailers or on-line. TEAC does not endorse any specific

product but, depending on the condition of your record

collection, it may be advisable to look into one of these

systems. Clean records protect your stylus from undue wear.

< Do not touch the record’s grooves. Only handle records, by

the edges or the label, with clean hands. Skin oils from even

clean hands can leave a residue on the record surface that will

gradually deteriorate the quality of your record.

label

grooves

edge

How to Replace the Stylus

The stylus should last about 200 hours under normal use.

However, it is recommended that the stylus be replaced as soon

as you notice a change in sound quality.

Prolonged use of a worn-out stylus may damage the record.

Caution:

<

Do not remove or bend the stylus.

<

To avoid injury, do not touch the needle.

<

Turn off the unit’s power before you replace the stylus.

<

Keep out of the reach of children.

<

Handle with care, as the stylus is delicate. Use of a bent or

broken stylus may damage the record and cause the turntable

to malfunction.

<

Do not expose stylus to extreme heat.

<

Contact a qualified repair company if you experience difficulty

in changing the stylus.

Replacing the Stylus

To remove the stylus assembly (the white one), hold the

cartridge at the end of the tone arm with one hand and slide

the stylus assembly in the direction “A” with your fingers of

the other hand.

The replacement stylus for this GF-650 is a STL-650. Please

contact TEAC Parts at (323) 726-0303, extension 840 to order.

Or call our automated Service Agency Locator at: (800) 447-

TEAC for the closest authorized repair company that can

replace the stylus for you.

To install a new stylus, insert its white assembly in the

direction “B” and then push it in the direction “C”. Make

certain that the assembly “clicks” up into place.

A

B

C

6

How to remove the disc How to hold the disc

<

Always place the disc on the disc tray with the label side

uppermost. (Compact discs can be played or recorded only on

one side.)

<

To remove a disc from its storage case, press down on the

center of the case and lift the disc out, holding it carefully by

the edges.

<

Never use such chemicals as record sprays, antistatic sprays or

fluid, benzine or thinner to clean the discs. Such chemicals

will do irreparable damage to the disc’s plastic surface.

<

Discs should be returned to their cases after use to avoid dust

and scratches that could cause the laser pickup to “skip.”

< Do not expose discs to direct sunlight or high humidity and

temperature for extended periods. Long exposure to high

temperatures will warp the disc.

<

Do not play any disc that is warped, deformed or damaged.

Playing such discs may cause irreparable harm to the playing

mechanisms.

<

CD-R and CD-RW discs are more sensitive to the effects of

heat and ultraviolet rays than ordinary CDs. It is important

that they are not stored in a location where direct sunlight

will fall on them, and away from sources of heat such as

radiators or heat-generating electrical devices.

<

Printable CD-R and CD-RW discs aren’t recommended, as the

label side might be sticky and damage the unit.

< Do not stick papers or protective sheets on the discs and do

not use any protective coating spray.

< Use a soft oil-based felt-tipped pen to write the information

on the label side. Never use a ball-point or hard-tipped pen,

as this may cause damage to the recorded side.

<

Never use a stabilizer. Using commercially available CD

stabilizers with this unit will damage the mechanisms and

cause them to malfunction.

<

Do not use CDs with an irregular shape (octagonal, heart

shaped, business card size, etc.). CDs of this sort can damage

the unit:

<

If you are in any doubt as to the care and handling of a CDR/

CD-RW disc, read the precautions supplied with the disc, or

contact the disc manufacturer directly.

< Should the disc become dirty, wipe the surface radially (from

the center hole outward towards the outer edge) with a soft,

dry cloth:

Please use CD, CD-R and CD-RW discs bearing the

“DIGITAL AUDIO” mark.

This unit CANNOT RECORD CD-R and CD-RW discs

designed for computer systems.

In this manual, although we refer to “CD-R” and CD-RW”

discs, we always mean “CD-R Digital Audio” and “CD-RW

Digital Audio”, even when this is not explicitly stated.

<

CD-R and CD-RW discs designed for computer systems and

properly recorded by a computer are playable, but this unit

cannot record, finalize nor erase them.

<

Depending on the quality of the disc and/or the condition of

the recording, some CD-R/CD-RW discs may not be playable.

< Copy-protected discs and other discs which do not conform

to the CD standard may not play back correctly in this player.

If you use such discs in this unit, TEAC Corporation and its

subsidiaries cannot be responsible for any consequences or

guarantee the quality of reproduction. If you experience

problems with such non-standard discs, you should contact

the producers of the disc.

CD

CD-R CD-RW

Discs

7

ENGLISH

About CD-R and CD-RW discs

CD-R discs can be recorded once only. Once they have been

used for recording, they cannot be erased or re-recorded.

However, if space is available on the disc (and the disc has not

been finalized), additional material can be recorded.

By contrast, a CD-RW disc can be used in much the same way

as a CD-R disc, but the last track or tracks recorded can be

erased, and the space on the disc can be re- used for other

recordings.

However, you should note that an audio CD created using a

CD-RW disc may not play back satisfactorily on every audio

CD player.

CD-R, by contrast, may be played satisfactorily on the majority

of audio CD players.

Finalizing

Although audio data may be written on a CD-R or CD-RW

disc, a standard CD player will not be able to play back the

audio until a final table of contents (TOC) has been written at

the start of the disc.

The process of writing this table of contents is known as

“finalizing”. Once this has been done, no further data can be

written to the disk.

Note that a CD-RW disc that has been finalized can be

“unfinalized”. This allows further tracks to be recorded to the

disc, provided that there is space on the disc.

<

Repeat, shuffle and programmed playback don’t work with

unfinalized (NO TOC) discs.

Recordable discs

In this manual, we use the term “recordable” disc to describe

a CD-R or CD-RW disc that has not been finalized, and has

enough space to record.

Remote Control Unit

1. Remove the battery compartment cover.

2. Insert two “AA” (R6, SUM-3) dry batteries. Make sure that the

batteries are inserted with their positive “+

” and negative

“_

” poles positioned correctly.

3. Close the cover.

Battery Replacement

If the distance required between the remote control unit and

main unit decreases, the batteries are exhausted. In this case

replace the batteries with new ones.

Precautions concerning batteries

<

Be sure to insert the batteries with correct positive “+” and

negative “_

” polarities.

<

Use batteries of the same type. Never use different types of

batteries together.

<

Rechargeable and non-rechargeable batteries can be used.

Refer to the precautions on their labels.

<

When the remote control unit is not to be used for a long

time (more than a month), remove the batteries from the

remote control unit to prevent them from leaking. If they leak,

wipe away the liquid inside the battery compartment and

replace the batteries with new ones.

<

Do not heat or disassemble batteries and never dispose of old

batteries by throwing them in a fire.

The provided Remote Control Unit allows the unit to be

operated from a distance.

When operating the remote control unit, point it towards the

REMOTE SENSOR on the front panel of the unit.

<

Even if the remote control unit is operated within the effective

range, remote control operation may be impossible if there

are any obstacles between the unit and the remote control.

<

If the remote control unit is operated near other appliances

which generate infrared rays, or if other remote control

devices using infrared rays are used near the unit, it may

operate incorrectly. Conversely, the other appliances may

operate incorrectly.

Battery Installation

8

Assembling the Turntable

Square opening

Round hole

Red tape ribbon

Pulley

Drive belt

Turntable platter

Base plate

Caution:

<

There is a drive belt hooked to the turntable platter's drive

rim. Be careful not to damage the drive belt when assembling

the turntable.

<

When turning on the power to the unit, the tone arm may

move if the cum was subjected to shock during transportation

and has been displaced.

We suggest you to assemble the turntable leaving the

vinyl tie intact that holds the tone arm.

When you use the GF-650 for the first time after you have

assembled the turntable (or after the GF-650 has been

transported), turn on the power to the unit and leave this

alone for more than 30 seconds. Thereafter remove the vinyl

tie.

1. Hook your fingers into the round holes of the turntable

platter and gently lift.

2. Carefully place the turntable platter on the center

spindle, making certain the platter is fully seated on the

spindle.

3. Turn the turntable platter by hand until the motor

pulley is visible through a square opening in the

turntable platter.

4. Insert your finger into the square opening and carefully

pull the end of the red tape ribbon so that the drive

belt hooks to the motor pulley.

To Open:

1 Lift the turntable cover all the way up until it stops.

2. Lower the cover slowly until the latch engages.

3. The cover will now stay open. If the latch does not engage,

repeat these steps again.

To Close:

1. Lift the cover all the way up until it stops.

2. The latch should disengage and you may now slowly lower

the cover.

3. Make sure you grasp the cover by the edges to avoid pinching

your fingers as it closes.

How to open/close the turntable cover

9

ENGLISH

5. Remove the red tape ribbon.

6. Slowly turn the turntable platter 5 or 6 times by hand

so that the drive belt is correctly seated into the pulley's

groove.

7. Place the record mat on top of the turntable platter.

8. Completely loosen the shipping screws by turning them

clockwise with a coin or screwdriver.

Cushioning material

cushioning material

Shipping screw

Base plate

9. Remove the two white cushioning materials from

beneath the base plate.

We suggest that you save the cushioning materials for

possible future moving or shipping.

When needed for transportation

1.Disassemble and pack the turntable in reverse order of

assembly.

2. Insert the two white cushioning materials into beneath the

base plate.

3. Rotate the two shipping screws counterclockwise until they

block.

4. Put the stylus guard back on.

5. Hold the tone arm with the vinyl tie.

If the drive belt is out of place

1. Lift and remove the turntable platter, and place it bottom side

up.

2. Place the drive belt along the outside wall of the turntable

platter’s drive rim.

3. Reassemble the turntable by following steps 1-7 of page 8

explained under the heading “Assembling the Turntable”.

But, in step 4, gently hold the drive belt itself (instead of the

red tape ribbon) and hook it to the motor pulley, and skip

step 5.

10

Connection

CAUTION

<

Switch off the power to all equipment before making connections.

<

Read the instructions of each component you intend to use with this unit.

<

Be sure to insert each plug securely. To prevent hum and noise, avoid bundling the

signal interconnection cables together with the AC power cord.

FM antenna

While in FM mode, tune in an FM station and extend the lead to find the best position

for the reception. This antenna may need to be repositioned if you move your unit to a

new location.

AUX IN/OUT jacks

Analog 2-channel audio signal is input or output from these jacks. Connect these jacks

to a CD player, cassette tape deck, etc. using commercially avaialble RCA cables.

Make sure to connect:

white plug q

white jack (L: left channel)

red plug q

red jack (R: right channel)

AC Power Cord

After all other connections have been completed, connect the plug to the AC wall

socket.

Be sure to connect the power cord to an AC outlet which supplies the correct voltage.

Hold the power plug when plugging or unplugging the power cord.

C

B

A

AUDIO

IN

AUDIO

OUT

RRLL

B

A

C

CD player, cassette tape deck, etc.

ENGLISH

11

Screws fixing the turntable for transportation

Before use, completely loosen the screws by turning them

clockwise with a coin or screwdriver.

Turntable

Speed selector

45 RPM adaptor

Tone arm

STOP lever

Pull this lever to stop playback of a record.

START lever

Pull this lever to start playback of a record.

Tone arm holder

Size selector

I

H

G

F

E

D

C

B

A

Identifying the Parts (Turntable)

A

I

H

E

G

F

D

A

B

C

Before use, remove the

stylus guard.

12

Identifying the Parts

A C HE FB GD

S R O L

M

K II

Q

P N J

Q

P

F

L

E

B

A

F

J

B

O

N

C

D

E

13

ENGLISH

POWER

Press this button to turn the unit on or off.

PHONO/AUX, FM/AM, CD

Press the PHONO/AUX button and select PHONO to play a

record.

Press the PHONO/AUX button and select AUX to listen to the

external source connected to the AUX IN jacks.

Press the FM/AM button to listen to the radio.

Press the CD button to play a CD.

Remote Sensor

When operating the remote control unit, point it towards the

REMOTE SENSOR.

Display panel (frequency)

When the unit is on, this display will light.

TRACK INCREMENT

During recording, use this button to divide tracks.

RECORD

Use this button to enter record pause mode.

Display

TUNED indicator

Lights when a station is correctly tuned in.

Speakers (stereo)

CD operation buttons

STOP (H

)

Use this button to stop playback or recording.

PLAY (y)

Use this button to start playback, recording, finalizing and

erasing.

PAUSE (J)

Use this button to pause playback or recording.

OPEN/CLOSE

In CD or PHONO/AUX mode, use this button to open and

close the disc tray.

<

This button don’t work in FM/AM mode.

VOLUME

Turn this knob to adjust the volume.

Disc Tray

M

L

K

J

I

H

G

F

E

D

C

B

The equipment draws a nominal amount of power from

the AC outlet even with its POWER switch in the OFF

position.

A

MUSIC SKIP (.//)

In CD mode, use these buttons to skip tracks.

Hold down these buttons to search for a part of a track.

REC LEVEL

In record pause mode, use this knob to adjust the recording

level.

FINALIZE

Use this button to finalize a CD-R/CD-RW disc.

ERASE

Use this button to erase or unfinalize a CD-RW disc.

TUNING

In FM/AM mode, turn this knob to tune in a station.

PHONES

For private listening, first reduce the volume level to

minimum. Then insert the plug from your headphones into

the PHONES jack, and adjust the volume by turning the

VOLUME knob. The sound from speakers will be cut off while

the headphones are plugged in.

MANUAL/AUTO REC

Use this button to select the mode of track number

assignment.

PROGRAM

In CD mode, use this button to program tracks.

CLEAR

In CD mode, use this button to clear programmed tracks.

REPEAT

In CD mode, use this button to select a repeat mode of CD.

DISPLAY

In CD mode, use this button to change the display.

SHUFFLE

In CD mode, use this button for shuffle playback.

Note:

To simplify explanations, instructions refer to names of

buttons and controls on the front panel, making no mention

of the use of remote control unit.

F

E

D

C

B

A

S

R

Q

P

O

N

14

Press the POWER switch to turn the unit on.

1

Select a source by pressing the corresponding button.

2

< To listen to an external source connected to AUX jacks, select

AUX by pressing the PHONO/AUX button once or twice.

Play the source, and adjust the volume by turning the

VOLUME knob.

3

Basic Operation

Caution:

<

Before use, completely loosen the shipping screws by turning

them clockwise with a coin and remove the stylus guard.

< When turning on the power to the unit, the tone arm may

move if the cum was subjected to shock during transportation

and has been displaced.

When you use the GF-650 for the first time, turn on the

power to the unit leaving the vinyl tie intact to prevent the

tone arm from moving and leave the unit alone for more than

30 seconds. Thereafter remove the vinyl tie.

Press the PHONO/AUX button once or twice to select

PHONO.

1

Select the size of record: 17cm or 30cm.

4

Put the record on the turntable.

When playing a 45 RPM record, use the included adaptor.

3

Gently open the dust cover.

Be careful not to pinch your finger.

2

1 3

2

Select the speed: 33 or 45.

5

Listening to a Record

ENGLISH

1 2

3

5 4

6

15

Shipping screw

Adaptor

Shipping screw

Pull the START lever toward you.

6

The turntable will start and the tone arm will automatically

move to the lead-in groove. When the record finishes playing,

the tone arm will automatically return to the tone arm holder

and the turntable will stop.

<

Playing records with the dust cover down will prevent dust

from settling on the turntable.

Please do not place anything on top of the turntable

cover, especially while playing a record.

< Don’t rock the unit nor switch off the power during playback.

<

The tone arm automatically returns to the tone arm holder

when it reaches the end of recording. But with records on

which the recorded groove runs into a further inner area than

in the case of normal records, the tone arm may lift and

return to the tone arm holder without playing towards the

end of recording.

<

To play a 25 cm (10 inch) record, manually start playing. If the

tone arm does not automatically return to the tone arm rest,

pull the STOP lever.

Manual Operation

Move the tone arm gently to the edge of the record (or the

starting point of a track), and gently lower the tone arm.

To Interrupt Playing the Record Midway

Pull the STOP lever toward you. The tone arm will lift and

return to the tone arm holder and the turntable will stop.

To stop playback manually, slightly lift the tone arm and

return it to the tone arm holder.

STOP lever

16

Press the OPEN/CLOSE button (L).

2

Place a disc on the tray with the printed label face up.

3

< Never place more than one disc on the tray.

<

The disc must be placed in the center of the disc tray. If the

disc is not correctly loaded, it may not be possible to open the

tray again once it has closed, so you should ensure the disc is

always centered on the tray.

<

Do not force the tray by hand during opening and closing

operations.

Press the CD button.

1

“

--

” blinks for a few seconds.

When no disc is set, “nOdISC” appears on the display.

3 2 4

1 5

Listening to the Radio

Select FM or AM using the FM/AM button.

1

Turn the TUNING knob to tune in a station.

2

If the reception is poor

AM broadcast

Turn around the unit to find the best position for AM

stations.

FM broadcast

Extend and turn around the FM antenna so that you can

receive the stations clearly.

<

The TUNED indicator lights when a station is correctly tuned

in.

<

The STEREO indicator lights when an FM stereo broadcast is

tuned in.

2

1

Listening to a CD 1

17

ENGLISH

Press the OPEN/CLOSE button (L) to close the tray.

4

Press the PLAY button (y) to start playback.

5

Disc playback starts from the first track, and the PLAY

indicator (y

) lights on the display.

<

If you load the disc, and then press the PLAY button without

having first closed the disc tray, the disc tray closes and

playback starts.

<

It takes a few seconds for the unit to load the disc. No

buttons will work during loading. Wait until the total number

of the tracks and the total play time of the disc are displayed.

disc type indicator

total play time of the disctotal number of the tracks

< The disc type indicator shows the type of disc currently

loaded.

CD:

A commercial pre-recorded CD

CD-R:

A finalized CD-R

CD-RW:

A finalized CD-RW

NO TOC CD-R:

A CD-R which has yet to be finalized

NO TOC CD-RW:

A CD-RW which has yet to be finalized

blank:

No disc or unreadable disc

To suspend playback temporarily

(pause mode)

A

Press the PAUSE button (J) during playback. Playback stops

at the current position.

To resume playback, press the PLAY button (y

) or the

PAUSE button (J

).

To stop playback

B

Press the STOP button (H) to stop playback.

B A

18

During playback, repeatedly press the SKIP button

(.

or/) until the desired track is found. The selected

track will be played from the beginning.

In the stop mode, press the SKIP button (.or/)

repeatedly until the track you want to listen to is found, and

press the PLAY button (y

) to start playback from the

selected track.

< When the . button is pressed during playback, the track

being played will be played from the beginning. To return to

the beginning of the previous track, press the .

button

twice.

To skip to the next or a previous track

C

Search for a part of a track

D

During playback, hold down the SKIP button (.or/)

and release it when the part you want to listen to is found.

Listening to a CD 2 Time Display

Each time the DISPLAY button is pressed, the display changes as

follows:

C D

Unfinalized CD-R/CD-RW, stopped

During recording

CD/CD-R/CD-RW playback

total number of the tracks total play time of the disc

remaining recording time of the disc

elapsed recording time of the track

remaining recording time of the disc

elapsed time of current track

time remaining for current track

total elapsed time of the disc

time remaining for the disc

19

ENGLISH

Shuffle Playback

Each time the REPEAT button is pressed, the repeat mode is

changed as follows:

REPEAT ALL (Repeat All the Tracks)

Press the REPEAT button once during playback.

All the tracks of the disc will be played repeatedly.

REPEAT 1 (Repeat one track)

Press the REPEAT button twice during playback.

The track being played will be played repeatedly. If you press

the MUSIC SKIP button and select another track, the track

you selected will be played repeatedly.

It is also possible to select a track to be repeated in the stop

mode. Press the REPEAT button twice and then select the

track number by pressing the MUSIC SKIP button. Press the

PLAY button to start playback.

<

If one of the following buttons is pressed, repeat mode will

be cancelled:

OPEN/CLOSE, POWER, FM/AM, PHONO/AUX

<

Repeat playback works with finalized discs only.

Repeat Playback

The tracks can be played randomly. Press the SHUFFLE button

during playback. (In the stop mode, press the SHUFFLE button

and the PLAY button.)

When the shuffle playback of all the tracks has been finished,

the unit stops and the shuffle playback mode is cancelled.

<

If you press the / button during shuffle playback, next

track will be randomly selected and played. If you press the

.

button, the currently played track will be played from

the beginning. A track cannot be replayed during shuffle

playback.

<

Shuffle playback doesn’t work during programmed playback.

<

If one of the following buttons is pressed, shuffle mode will

be cancelled:

SHUFFLE in the stop mode, OPEN/CLOSE, POWER, FM/AM,

PHONO/AUX

< Shuffle playback works with finalized discs only.

REPEAT ALL REPEAT 1

(off)

20

Programmed Playback

The track is programmed, and “P-02” is displayed.

Repeat step and to program more tracks.

<

You can program up to 32 tracks.

<

To cancel the program mode, press the STOP button (H).

When the selection of track numbers has been finished,

press the PLAY button (y

) to start program playback.

4

32

Up to 32 tracks can be programmed in the desired order.

<

Insert a disc and select “CD” before beginning programming.

<

Shuffle playback does not work during programmed

playback.

<

Programmed playback works with finalized discs only.

Press the PROGRAM button in the stop mode.

1

“PROGRAM” indicator blinks, and “P-01” appears on the

display.

Press the MUSIC SKIP button (. or /) to select a

track.

2

Press the PROGRAM button.

3

track number

La page charge ...

TEAC GF-650 Manuel utilisateur

Ce manuel convient également à

TEAC GF-650 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents