NAPOLEON BILEX730RBIPSS Manuel utilisateur

Marque: NAPOLEON

Modèle: BILEX730RBIPSS

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

BILEX730RBINSS

PG.29

www.napoleongrills.com

N415-0326 JAN 16.19

APPLY SERIAL NUMBER LABEL FROM CARTON

Serial No.

XXXXXX000000

MODEL NO.

Noce to Installer: Leave these instrucons with the grill owner for future reference.

This gas grill must be used only outdoors in a well-venlated space and must not be used inside a

building, garage, screened-in porch, gazebo or any other enclosed area.

WARNING! CABINET FRAME, CABINET AND COUNTER TOP MUST BE MADE FROM NON-COMBUSTIBLE MATERIAL.

WARNING

Do not try to light this appliance without

reading the “LIGHTING” instrucons secon of

this manual.

Do not store or use gasoline or other

ammable liquids or vapors in the vicinity of

this or any other appliance. An L.P. cylinder

not connected for use must not be stored in

the vicinity of this or any other appliance. If

the informaon in these instrucons is not

followed exactly, a re or explosion may result,

causing property damage, personal injury or

death.

BILEX730

Wolf Steel Ltd.

214 Bayview Drive,

Barrie, Ontario, CANADA L4N 4Y8

[email protected]

DANGER

IF YOU SMELL GAS:

• Shut o gas to the appliance.

• Exnguish any open ame.

• Open lid.

• If odor connues, keep away from the

appliance and immediately call your gas

supplier or re department.

N415-0326 JAN 16.19.indd 1 1/21/2019 3:49:25 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Aluminum castings / stainless steel base

...........................................

15 years

Stainless steel lid

................................................................................

15 years

Porcelain enamel lid

...........................................................................

15 years

Stainless steel cooking grids

..............................................................

15 years

Stainless steel tube burners

...............................................................

10 years full coverage, plus 50% off until the 15th year

Stainless steel sear plates 5 years full coverage, plus 50% off until the 15th year

.....................................

5 years full coverage, plus 50% off until the 15th year

Ceramic infrared burners (excluding screen)

................................

years full coverage, plus 50% off until the 15th year

All other parts

napoleongrills.com

Napoleon President’s 15 Year Limited Warranty

NAPOLEON products are designed with superior components and materials, and are assembled by trained

craftsmen who take great pride in their work. The burner and valve assembly are leak tested and test-fired at a

quality test station. This grill has been thoroughly inspected by a qualified technician before packaging and shipping

to ensure that you, the customer, receive the quality product you expect from NAPOLEON.

NAPOLEON warrants that components in your new NAPOLEON product will be free from defects in material and

workmanship from the date of purchase, for the following period:

...............................................................

2 years

................................................................................

Porcelain-enameled cast iron cooking grids

*Conditions and Limitations

This Limited Warranty creates a warranty period as speciﬁed in the

aforementioned table, for any product purchased through an authorized NAPOLEON

dealer, and entitles the original purchaser to the speciﬁed coverage in respect of

any component replaced within the warranty period, either by NAPOLEON or an

authorized NAPOLEON dealer, to replace a component of such product that has

failed in normal private use as a result of a manufacturing defect. The “50% off”

indicated in the table means the component is made available to the purchaser at

a 50% discount off the regular retail price of the component for the period

indicated. This Limited Warranty does not cover accessories or bonus items.

For greater certainty, “normal private use” of a product means that the product:

has been installed by a licensed, authorized service technician or contractor, in

accordance with the installation instructions included with the product and all

local and national building and ﬁre codes; has been properly maintained; and has

not been used as a communal amenity or in a commercial application.

Similarly, “failure” does not include: over-ﬁring, blow outs caused by

environmental conditions such as strong winds or inadequate ventilation,

scratches, dents, corrosion, deterioration of painted and plated ﬁnishes,

discoloration caused by heat, abrasive or chemical cleaners or UV exposure,

chipping of porcelain enameled parts, or damages caused by misuse, accident,

hail, grease ﬁres, lack of maintenance, hostile environments such as salt or

chlorine, alterations, abuse, neglect or parts installed from other manufacturers.

Should deterioration of parts occur to the degree of non-performance (rusted

through or burnt through) within the duration of the warranted coverage, a

replacement part will be provided. The replacement component is the sole

responsibility of NAPOLEON deﬁned by this Limited Warranty; in no event will

NAPOLEON be responsible for installation, labor or any other costs or expenses

related to the re-installation of a warranted part, for any incidental, consequential,

or indirect damages or for any transportation charges, labor costs or export duties.

This Limited Warranty is provided in addition to any rights afforded to you by local

laws. Accordingly, this Limited Warranty imposes no obligation upon NAPOLEON to

keep parts in stock. Based on the availability of parts, NAPOLEON may at its

discretion discharge all obligations by providing a customer a prorated credit

towards a new product. After the ﬁrst year, with respect to this Limited Warranty

NAPOLEON may, at its discretion, fully discharge all obligations with respect to this

warranty by refunding to the original warranted purchaser the wholesale price of

any warranted but defective part(s).

The bill of sale or copy will be required together with a serial number and a

model number when making any warranty claims from NAPOLEON.

NAPOLEON reserves the right to have its representative inspect any product

or part prior to honoring any warranty claim. You must contact NAPOLEON

Customer Service or an authorized NAPOLEON dealer to obtain the beneﬁt of

the warranty coverage.

N415-0326 JAN 16.19.indd 2 1/21/2019 3:49:26 PM

www.napoleongrills.com

N415-0326 JAN 16.19

WARNING! Failure to follow these instrucons could result in property damage, personal injury

or death. Read and follow all warnings and instrucons in this manual prior to operang grill.

Safe Operang Pracces

• This gas grill must be assembled exactly according to the instrucons in the manual. If the grill was store

assembled, you must review the assembly instrucons to conrm correct assembly and perform the

required leak tests before operang the grill.

• Read the enre instrucon manual before operang the gas grill.

• This gas grill must be used only outdoors in a well-venlated space and must not be used inside a building,

garage, screened-in porch, gazebo or any other enclosed area.

• This gas grill must not be installed in or on recreaonal vehicles and/or boats.

• Do not locate unit in windy sengs. High winds adversely aect the cooking performance of the gas grill.

• Under no circumstances should this gas grill be modied.

• Do not operate unit under overhead combusble construcon.

• Maintain proper clearance to combusbles (16” (410 mm) to rear of unit and 7” (180 mm) to sides).

Addional clearance of 24” (610 mm) is recommended near vinyl siding or panes of glass.

• Gas must be turned o at the gas supply valve when the gas grill is not in use.

• If the enclosure is to house a propane cylinder, the tank poron of the enclosure must be venlated

according to local codes and must not have communicaon with the cavity used to enclose the gas grill. A

propane tank can not be stored below the gas grill.

• Do not aempt to use a cylinder that is not equipped with a QCC1 type connecon.

• When the propane cylinder is connected to the appliance, the gas grill and cylinder must be stored

outdoors in a well-venlated space.

• When the gas grill is to be stored indoors, the connecon between the propane cylinder and the gas grill

must be disconnected and the cylinder removed and stored outdoors in a well venlated space out of

reach of children. Disconnected cylinders must not be stored in a building, garage or any other enclosed

area. Natural gas units must be disconnected from the supply when being stored indoors.

• Inspect the fuel supply hose before each use. If there is evidence of excessive abrasion or wear or the hose

is cut, it must be replaced prior to using the gas grill with a replacement hose assembly specied by the

grill manufacturer.

• Leak test the unit before inial use, annually, and whenever any gas components are replaced.

• Follow lighng instrucons carefully when operang grill.

• Burner controls must be o when turning supply cylinder valve on.

• The lid is to be closed during the gas grill preheang period on all models except the BISZ300NFT/PFT and

the built-in side burner BISB245.

• The BISZ300NFT/PFT and the built-in side burner BISB245 are supplied with a at cover for storage and

protecon from the elements. Never place this cover on the grill while hot or operang. Allow grill to cool

completely before covering.

• Adults and especially children should be alerted to the hazards of high surface temperatures. Young

children should be supervised near the gas grill.

• Do not leave grill unaended when operang.

• Do not light burners with lid closed.

• Do not operate rear burner with main burners operang.

• Do not move grill when hot or operang.

• Keep any electrical supply cord and fuel supply hose away from any heated surfaces.

• Ensure sear plates are posioned properly according to sear plate installaon instrucons. The holes must

be towards the front of the gas grill (if applicable).

• Clean grease tray and sear plates regularly to avoid build-up, which could lead to grease res.

• Remove warming rack before lighng rear burner. The extreme heat will damage the warming rack.

• Inspect infrared burner venturi tube for spider webs and other obstrucons periodically. Clean the tubes

completely if you nd any such obstrucons.

• Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with heated unit. A large

temperature dierenal can cause chipping in the porcelain.

• Do not allow cold water (rain, sprinkler, hose, etc.) to come in contact with ceramic burners. A large

temperature dierenal can cause cracking in the ceramic le.

• Do not use a pressure washer to clean any part of the unit.

N415-0326 JAN 16.19.indd 3 1/21/2019 3:49:26 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Gas Hook-Up Instrucons

WARNING! This grill is designed for non-combusble enclosures only, and must be installed and

serviced by a qualied installer to local codes.

WARNING!

Cabinet frame, cabinet, and counter top must be made from non-combusble material.

WARNING! As indicated on the rang plate, this gas grill is designed to operate with gas supply

pressures of 11” WC for Propane and 7” WC for Natural Gas. For installaons where the gas supply

pressure exceeds these requirements, a regulator must be installed upstream of the grill’s components.

If the gas supply pressure is lower than these requirements, the unit will be under-red and will not

reach the maximum temperatures. Ensure that the supply line size complies with local and/or naonal

installaon codes.

BUILT IN PROPANE GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and

piping should be located as shown in the built-in instrucons. A exible metal connector is included to

simplify the installaon of the unit. Connect this exible metal connector to the are ng on the end of

the manifold. Connect the other end of the connector to the gas piping. Ensure that the connector does

not pass through a wall, oor, ceiling or paron, and is protected from damage. Do not use a hose to

connect the unit except to connect the cylinder regulator to the piping system. It must be connected with

rigid pipe, copper tube or an approved exible metal connector which complies with Z21.24/ CSA 6.10 or

ANSI Z21.75/CSA 6.27.

General Informaon

This Gas Barbecue Is Cered Under Canadian And American Naonal Standards, CAN/CSA 1.6 - 2005 and

ANSI Z21.58-2005 respecvely for Outdoor Gas Grills and should be installed to conform with local codes.

In absence of local codes, install to the current CAN/CGA-B149.1 Propane Installaon Code in Canada or to

the Naonal Fuel Gas Code, NFPA54/ANSI Z223.1 in the United States.

If a rosserie motor is used, it must be electrically grounded in accordance with local codes or, in absence

of local codes, with the current CSA C22.1 Canadian Electrical Code in Canada or the Naonal Electrical

Code, ANSI/NFPA 70 in the United States.

WARNING: This product can expose you to chemicals including lead and lead compounds, which are

known to the State of California to cause cancer, and chemicals including di-n-butyl phthalate, which are

known to the State of California to cause birth defects or other reproducve harm. For more informaon

go to www.P65Warnings.ca.gov.

Propane Cylinder Specicaons

WARNING! If these instrucons are not followed exactly, a re causing death or serious injury

may occur.

WARNING! Do not store a spare propane cylinder on the shelf beneath the barbecue.

If the gas grill is being supplied with propane from a portable cylinder, a regulator specied by the

manufacturer must be used. The regulator must supply a pressure of 11 inches water column (0.39 PSI)

to the gas grill and have a QCC1 type ng. Cylinders to be used with this unit must be supplied with a

QCC1 cylinder valve. A QCC1 cylinder has a posive seang connecon, which will not allow gas ow unl

a posive seal has been achieved. It is also equipped with an excess ow device. In order to aain full ow

to the grill, the valves must be in the o posion when the cylinder valve is turned on.

A dented or rusty cylinder may be hazardous and should be checked by your propane supplier. Never

use a cylinder with a damaged valve. Use only a propane supply cylinder constructed and marked in

accordance with the specicaons for LP-gas cylinders of the Naonal Standard of Canada, CAN/CSA-b339,

Cylinders, Spheres and Tubes for Transportaon of Dangerous Goods; and Commission, as applicable or

the Specicaons for LP-Gas Cylinders of the U.S. Department of Transportaon (D.O.T.). Cart models have

been designed for use with a 20 lb (9.1 kg) size propane cylinder only (not supplied).

The propane cylinder must be provided with a cylinder connecon device compable with the connecon

for outdoor cooking appliances. The propane cylinder must be provided with a shut-o valve terminang

in a propane cylinder valve type QCC1, and a safety relief device having direct communicaon with the

vapor space of the cylinder. The cylinder supply system must be arranged for vapor withdrawal and the

cylinder shall include a collar to protect the cylinder valve. The cylinder shall incorporate a listed OPD

(overll protecon device). Do not store a spare LP-gas cylinder under or near this appliance. Never ll the

cylinder beyond 80 percent full. If the preceding informaon is not followed exactly, a re causing death or

serious injury may occur.

N415-0326 JAN 16.19.indd 4 1/21/2019 3:49:28 PM

www.napoleongrills.com

N415-0326 JAN 16.19

The installaon must comply with CAN B149.1 Natural Gas and Propane installaon code in Canada, or

to the Naonal Fuel Gas code, ANSI Z223.1 in the United States. The gas supply pipe must be suciently

sized to supply the BTU/h specied on the rang plate, based on the length of the piping run. If installing

a side burner, a separate line must be branched o to the side burner unit and enter the side burner

opening at the specied locaon. If the enclosure is to house a propane cylinder, the tank poron of the

enclosure must be venlated according to local codes, and must not have communicaon with the cavity

used to enclose the gas grill. A propane cylinder can not be stored below the gas grill.

BUILT IN CYLINDER ENCLOSURES: Built in cylinder enclosures which completely enclose the cylinder must

have both of the following:

1. At least one unobstructed venlaon opening on the exposed exterior side of the enclosure located

within 5 in (127mm) of the top of the enclosure. The opening must have a total free area of more than 20

(130 cm

) for a 20 lb (9.1 kg) cylinder and 30 in

(195 cm

) for a 30 lb (13.6 kg) cylinder.

2. At least one venlaon opening on the exposed, exterior side of the enclosure located 1 in (25.4 mm)

or less from the oor level. The opening must have a total free area of more than 10 in

(65 cm

) for a 20

lb (9.1 kg) cylinder and 15 in

(100 cm

) for a 30 lb (13.6 kg) cylinder. The upper edge must be no more

than 5 in (127 mm) above the oor level.

Every opening must be large enough to permit the entrance of a 1/8 in (3.2 mm) rod.

WARNING!

• The cylinder valve(s) must be readily accessible for hand operaon. A door on the enclosure to gain

access to the cylinder valves is acceptable, provided it is non-locking and can be opened without

the use of tools.

• The enclosure for the LP-gas cylinder must isolate the cylinder from the burner compartment to

provide shielding from radiaon, a ame barrier, and protecon from foreign material, such as hot

drippings. The enclosure cannot be located directly below the grill.

• There must be a minimum clearance of 2 in (51 mm) between the oor of the LP-gas cylinder

enclosure and the ground.

• The enclosure must be designed so that the LP-gas cylinder can be connected, disconnected and

the connecons inspected and tested outside the cylinder enclosure. Any connecons that can be

disturbed when installing the cylinder in the enclosure must be accessible for tesng inside the

enclosure.

CYLINDER SIZE OPENING A AREA OPENING B AREA

20 lb (9.1 kg)

20 in

(130 cm

) 10 in

(65 cm

)

30 lb (13.6 kg)

30 in

(195 cm

) 15 in

(100 cm

)

5” (127 mm)

MAXIMUM

1” (25.4 mm)

MAXIMUM

OPENING

2” (51 mm)

MINIMUM

PARTITION TO ISOLATE

CYLINDER FROM GRILL

NON LOCKING DOOR

34” (864 mm)

RECOMMENDED

5” (127 mm)

MAXIMUM

N415-0326 JAN 16.19.indd 5 1/21/2019 3:49:30 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Leak Tesng Instrucons

WARNING! A leak test must be performed annually and each me a cylinder is hooked up or if a

part of the gas system is replaced.

WARNING! Never use an open ame to check for gas leaks. Be certain no sparks or open ames

are in the area while you check for leaks. Sparks or open ames will result in a re or explosion,

damage to property, serious bodily injury, or death.

Leak tesng: This must be done before inial use, annually, and whenever any gas components are

replaced or serviced. Do not smoke while performing this test, and remove all sources of ignion. See Leak

Tesng Diagram for areas to check. Turn all burner controls to the o posion. Turn gas supply valve on.

Brush a half-and-half soluon of liquid soap and water onto all joints and connecons of the regulator,

hose, manifolds and valves.

Bubbles will indicate a gas leak. Either ghten the loose joint or have the part replaced with one

recommended by the Napoleon Customer Soluons department and have the grill inspected by a cered

gas installer.

If the leak cannot be stopped, immediately shut o the gas supply, disconnect it, and have the grill

inspected by a cered gas installer or dealer. Do not use the grill unl the leak has been corrected.

BUILT IN NATURAL GAS HOOK-UP: The piping up to the gas grill is the responsibility of the installer and

piping should be located as shown in the built-in instrucons. A exible metal connector is included to

simplify the installaon of the unit. Connect this connector to the are ng on the end of the manifold.

Connect the other end of the connector to the gas piping. Ensure that the connector does not pass

through a wall, oor, ceiling or paron, and is protected from damage. Do not use a hose to connect the

unit. It must be connected with rigid pipe, copper tube or an approved exible metal connector which

complies with Z21.4 /CSA 6.10 or ANSI Z21.75/CSA 6.27.

The installaon must comply with CAN B149.1 Natural Gas and Propane Installaon Code in Canada, or

to the Naonal Fuel Gas Code, ANSI Z223.1 in the United States. The gas supply pipe must be suciently

sized to supply the BTU/h specied on the rang plate, based on the length of the piping run. If installing

a side burner, a separate line must be branched o to the side burner unit and enter the side burner

opening at the specied locaon.

WARNING! Built in units are supplied with a drip pan which holds only a minimal amount of

grease. To prevent grease res, the pan must be cleaned aer each use.

WARNING! Access must be provided to the inside of the enclosure to make gas connecons.

DANGER! Read all instrucons carefully before operang the grill. Failure to follow these

instrucons exactly could result in a re causing serious injury or death.

The enre installaon must be leak tested before operang the grill.

N415-0326 JAN 16.19.indd 6 1/21/2019 3:49:33 PM

www.napoleongrills.com

N415-0326 JAN 16.19

WARNING! Open lid.

WARNING! Ensure all burner controls are in the o posion. Turn on the gas supply

valve.

Main Burner

Lighng

Rear Burner Lighng

(Rosserie Burner)

(if equipped)

Side Burner Lighng

(If equipped)

1. Open grill lid. 1. Open grill lid. 1. Open side burner cover.

2. Push and turn any main burner knob slowly

to the ’hi’ posion. This acon will ignite the

pilot ame which will in turn light the selected

burner. If the pilot lights, connue to push down

on the control knob unl the burner lights and

then release.

2. Remove the warming rack. 2. Push and turn side burner control to

high posion.

3. If the pilot does not ignite, then immediately

turn the control knob back to the ‘o posion

and repeat step 2 several mes.

3. Push and turn the rosserie burner

control knob slowly to the ‘hi’ posion.

This acon will ignite the pilot ame

which will in turn light the burner. If the

pilot lights, connue to push down on

the burner control knob unl the burner

lights then release.

3. Press and hold igniter buon unl

burner lights, or light by match.

4. If the pilot and burner will not ignite within

5 seconds, turn the control knob to the ‘o’

posion and wait 5 minutes for any excess gas

to dissipate. Either repeat steps 2 and 3 or light

with a match.

4. If the burner does not ignite, then

immediately turn the control knob back

to the ‘o’ posion and repeat step 3

several mes.

4. If the burner will not ignite within 5

seconds, turn the control knob to the ‘o’

posion and wait 5 minutes for any excess

gas to dissipate. Either repeat steps 2 and

3 or light with a match.

5. If lighng the unit with a match, clip the

match into the supplied lighng rod. Hold the

lit match down through the grill and sear plate

while turning the corresponding burner valve

to high.

5. If the burner will not ignite within 5

seconds, turn the control knob to the

‘o’ posion and wait 5 minutes for any

excess gas to dissipate. Either repeat

steps 3 and 4 or light with a match.

WARNING! The propane cylinder is equipped with an excess ow device. Unless all burners are

turned o prior to turning the cylinder on, only small ames and low heat will be achievable.

WARNING! Do not use the rear burner (rosserie burner) with the main burners operang.

O Posion

Lighng Instrucons

Lights

Le

Burner

Le Centre

Burner

Rear

Burner

Infra Red

Burner

Right Centre

Burner

Centre

Burner

N415-0326 JAN 16.19.indd 7 1/21/2019 3:49:36 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Cooking Instrucons

Inial Lighng: When lit for the rst me, the gas grill emits a slight odor. This is a normal temporary

condion caused by the “burn-in” of internal paints and lubricants used in the manufacturing process and

does not occur again. Simply run the main burners on high for approximately one-half hour.

Main Burner Use: When searing foods, we recommend preheang the grill by operang all main burners

in the high posion with the lid closed for approximately 10 minutes. Food cooked for short periods of

me (sh, vegetables) can be grilled with the lid open. Cooking with the lid closed will ensure higher, more

even temperatures that can reduce cooking me and cook meat more evenly. Food that has a cooking

me longer than 30 minutes, such as roasts, can be cooked indirectly (with the burner lit opposite to the

food placement). When cooking very lean meats, such as chicken breasts or lean pork, the grids can be

oiled before pre-heang to reduce scking. Cooking meat with a high degree of fat content can create

are-ups. Either trim the fat or reduce temperatures to inhibit this. Should a are-up occur, move food

away from the ames and reduce the heat. Leave the lid open. See Your All Season Grill cookbook by

Napoleon for more detailed instrucons.

Rear Burner Use (If Equipped): Remove the warming rack prior to use, the extreme heat will damage the

warming rack. Cooking grids should also be removed if they interfere with the rosserie. The rear burner

is designed to be used in conjuncon with the rosserie kit available from your dealer. See the rosserie

kit assembly instrucons.

To use the counterbalance - remove the rosserie motor from the gas grill. Place the spit with meat

being cooked across the hangers inside the grill. The meat will naturally hang with the heavy side down.

Tighten the counterbalance arm and weight so the arm is facing up. Slide the counterweight in or out

to balance the load and ghten in place. Re-install the motor and begin cooking. Place a metal dish

underneath the meat to collect drippings for basng and naturally delicious gravy. Basng liquid may be

added as required. To seal in juices, rst operate rear burner on high unl brown, then reduce the heat

to thoroughly cook foods. Keep the lid closed for best results. Your roasts and fowl will brown perfectly

on the outside and stay moist and tender on the inside. For example, a 3 pound chicken on the rosserie

will be done in approximately 1½ hours on medium to high. Search Grill Master Recipes at www.

napoleongrills.com/recipes for “rosserie”.

ATTENTION! Barbecue sauce and salt can be corrosive and will cause rapid deterioraon of

the gas grill components unless cleaned regularly. When nished cooking disassemble rosserie

components, wash thoroughly with warm soapy water and store indoors.

Direct Cooking: Place food to be cooked on the grill directly over the heat. This method is generally used

for searing or for foods that do not require prolonged cooking mes such as hamburgers, steaks, chicken

pieces, or vegetables. The food is rst seared to trap-in the juices and avor, and then the temperature is

lowered to nish cooking the food to your preference.

Indirect Cooking: With one or more burners operang, place food to be cooked on the grill over a burner

that is not operang. The heat circulates around the food, cooking slowly and evenly. Cooking with this

method is much the same as cooking in your oven and is generally used for larger cuts of meats such

as roasts, chickens or turkeys, but can also be used for cooking foods that are prone to are-ups or for

smoking foods. Lower temperatures and slower cooking mes result in tender foods.

Infrared Main Burner Use (If Equipped): Follow the Infrared Burner Ignion procedures and operate on

high for 5 minutes with the lid closed or unl the ceramic burners glow red. Place food on the grill(s) and

cook according to mes listed in the Infrared Grilling Chart. Depending upon your taste, connue cooking

over infrared burners on high, medium, or low, turning food frequently, or place food over unlit burners,

close lid, and allow the oven temperature to slowly nish cooking your food.

CAUTION! Due to the intense heat the infrared burners provide, food le unaended over burners

will burn quickly. Keep the lid open when cooking with the infrared burners set to high. The intense heat

ensures adequate searing temperatures even with the lid open. This also allows observaon of the food

to prevent burning.

N415-0326 JAN 16.19.indd 8 1/21/2019 3:49:37 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Infrared Heat

Most people don’t realize that the heat source we are most familiar with, our sun, warms the earth using

mainly infrared energy. This is a form of electro-magnec energy with a wavelength just greater than the

red end of the visible light spectrum but less than a radio wave. This energy was discovered in 1800 by Sir

William Herschel who dispersed sunlight into its component colors using a prism. He showed that most

of the heat in the beam fell into the spectral region just beyond the red end of the spectrum, where no

visible light existed. Most materials readily absorb infrared energy in a wide range of wavelengths, causing

an increase in its temperature. The same phenomenon causes us to feel warmth when we are exposed to

sunlight. The infrared rays from the sun travel through the vacuum of space, through the atmosphere, and

penetrate our skin. This causes increased molecular acvity in the skin, which creates internal fricon and

generates heat, allowing us to feel warmth.

Foods cooked over infrared heat sources are heated by the same principle. Charcoal grilling is our most

familiar choice for infrared cooking. The glowing briquees emit infrared energy to the food being cooked

with very lile drying eect. Any juices or oils that escape from the food drip onto the charcoal and

vaporize into smoke giving the food its delicious grilled taste. The Napoleon infrared burner cooks in the

same way. In each burner, 10,000 ports – each with its own ny ame – cause the surface of the ceramic

le to glow red. This glow emits the same type of infrared heat to the food as charcoal, without its hassle

or mess. Infrared burners also provide a more consistently heated area that is far easier to regulate than

a charcoal re. For instant searing, the burners can be set to high, yet they can also be turned down for

slower cooking. We all know how dicult that is on a charcoal re. Tradional gas burners heat the food in

a dierent way. The air surrounding the burner is heated by the combuson process and then rises to the

food being cooked. This generates lower grill temperatures that are ideal for more delicate cuisine such

as seafood or vegetables, whereas Napoleon’s infrared burners produce searing heat for juicier, taser

steaks, hamburgers and other meats. For cooking mes and ps refer to the Infrared Grilling Chart.

N415-0326 JAN 16.19.indd 9 1/21/2019 3:49:37 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Infrared Grilling Chart

Food Control Seng Cooking Time Helpful Suggesons

Steak

1 in. (2.54cm)

thick

High seng 2 min. each side.

High seng 2 min. each side

then medium seng.

High seng 2 min. each side

then medium seng.

4 min. – Rare

6 min. – Medium

8 min. – Well done

When selecng meat for

grilling, ask for marbled fat

distribuon. The fat acts as

a natural tenderizer while

cooking and keeps it moist and

juicy.

Hamburger

1/2 in. (1.27cm)

thick

High seng 2 min. each side.

High seng 2 1/2 min. each

side.

High seng 3 min. each side.

4 min. – Rare

5 min. – Medium

6 min. – Well done

Preparing hamburgers to

order is made easier by

varying the thickness of your

paes. To add an exoc taste

to your meat, try adding

hickory-avored woodchips to

Napoleon’s woodchip smoker.

Chicken pieces High seng 2 min. each side.

then medium-low to low

seng.

20-25 min. The joint connecng the thigh

and the leg from the skinless

side should be sliced 3/4 of the

way though for the meat to lay

aer on the grill. This helps it

to cook faster and more evenly.

To add a trademark taste

to your cooking, try adding

mesquite-avoured woodchips

to your Napoleon woodchip

smoker, oponal accessory.

Pork chops Medium 6 min. per side Trim o the excess fat before

grilling. Choose thicker chops

for more tender results.

Spare ribs High seng for 5 minutes

low to nish

20 min. per side

turn oen

Choose ribs that are lean and

meaty. Grill unl meat easily

pulls away from the bone.

Lamb chops High seng for 5 minutes

medium to nish

15 min. per side Trim o the excess fat before

grilling. Choose extra thick

chops for more tender results.

Hot dogs Medium - Low 4-6 min. Select the larger size wieners.

Slit the skin lengthwise before

grilling.

N415-0326 JAN 16.19.indd 10 1/21/2019 3:49:37 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Note: Stainless steel tends to oxidize or stain in the presence of chlorides and suldes, parcularly in

coastal areas and other harsh environments, such as the warm, highly humid atmosphere around pools

and hot tubs. These stains could be perceived as rust, but can be easily removed or prevented. To provide

stain prevenon and removal, wash all stainless steel and chrome surfaces every 3-4 weeks or as oen as

required with fresh water and/or stainless steel cleaner.

WARNING! Always wear protecve gloves and safety glasses when servicing your grill.

WARNING! To avoid the possibility of burns, maintenance should be done only when the grill is

cool. Avoid unprotected contact with hot surfaces. Ensure all burners are turned o. Clean grill in an

area where cleaning soluons will not harm decks, lawns, or paos. Do not use oven cleaner to clean

any part of this gas grill. Do not use a self-cleaning oven to clean cooking grids or any other parts of

the gas grill. Barbecue sauce and salt can be corrosive and will cause rapid deterioraon of the gas grill

components unless cleaned regularly.

Cleaning Instrucons

Grids And Warming Rack: The grids and warming rack are best cleaned with a brass wire brush during

the pre-heang period. Steel wool can be used for stubborn stains. It is normal that stainless grids (if

equipped) will discolor permanently from regular usage due to the high temperature of the cooking

surface.

Control Panel: The control panel text is printed directly on the stainless steel and with proper

maintenance will remain dark and legible. To clean the panel, use only warm soapy water. Never apply

abrasive cleaners on any stainless surfaces, especially the printed poron of the control panel or the

prinng will gradually rub o.

Cleaning Inside The Gas Grill: Remove the cooking grids. Use a brass wire brush to clean loose debris from

the casng sides and underneath the lid. Scrape the sear plates with a puy knife or scraper, and use a

wire brush to remove the ash. Remove the sear plates and brush debris from the burners with the brass

wire brush. Sweep all debris from inside the gas grill into the drip pan.

WARNING! Built in units are supplied with a drip pan which holds only a minimal amount of

grease. To prevent grease res, the pan must be cleaned aer each use.

Drip Pan: Accumulated grease is a re hazard. Clean the drip pan aer each use to avoid grease buildup.

Grease and excess drippings pass through to the drip pan, located beneath the gas grill. To clean the drip

pan, slide the drip pan free of the grill. Never line the drip pan with aluminum foil, sand or any other

material as this could prevent the grease from owing properly. The pan should be scraped out with a

puy knife or scraper.

Cleaning The Outer Grill Surface: Do not use abrasive cleaners or steel wool on any painted, porcelain or

stainless steel parts of your Napoleon Grill. Doing so will scratch the nish. Exterior grill surfaces should be

cleaned with warm soapy water while the metal is sll warm to the touch. To clean stainless surfaces, use

a stainless steel or a non-abrasive cleaner. Always wipe in the direcon of the grain. Over me, stainless

steel parts discolor when heated, usually to a golden or brown hue. This discoloraon is normal and does

not aect the performance of the grill. Porcelain enamel components must be handled with addional

care. The baked-on enamel nish is glass-like, and will chip if struck. Touch-up enamel is available from

your Napoleon Grill dealer.

N415-0326 JAN 16.19.indd 11 1/21/2019 3:49:39 PM

www.napoleongrills.com

N415-0326 JAN 16.19

WARNING! Always wear protecve gloves and safety glasses when cleaning your grill.

WARNING! Turn o the gas at the source and disconnect the unit before servicing. To avoid

the possibility of burns, maintenance should be done only when the grill is cool. A leak test must be

performed annually and whenever any component of the gas train is replaced or gas smell is present.

Combuson Air Adjustment: (This must be done by a qualied gas installer.) The air shuer is factory set

and should not need adjusng under normal condions. Under extreme eld condions, adjustments

might be required. When the air shuer is adjusted correctly the ames will be dark blue, pped with light

blue and occasionally yellow.

• With too lile air ow to the burner, the ames are lazy yellow and can produce soot.

• With too much air ow, the ames li erracally and can cause dicules when lighng.

Adjusng the air shuer:

1. Remove cooking grids and sear plates and leave lid open.

2. Loosen air-shuer lock screw located at the mouth of the burner and open or close air shuer as

required. The normal opening sengs are:

Main Tube Burner Propane 5/32” (4mm)

Natural 5/32” (4mm)

*Infra-Red burners have no air adjustment.

3. Light the burners and set to high. Visually inspect burner ames. When the shuers are set correctly,

turn burners o, ghten locking screws, and replace removed parts. Ensure that the insect screens are

installed.

Maintenance Instrucons

Tube Burner: The burners are made from heavy wall 304 stainless steel, but extreme heat and a corrosive

environment can cause surface corrosion to occur. This can be removed with a brass wire brush.

CAUTION! Beware of Spiders.

Spiders and insects are aracted to the smell of propane and natural gas. The burner is equipped with an

insect screen on the air shuer, which reduces the likelihood of insects building nests inside the burner

but does not enrely eliminate the problem. A nest or web can cause the burner to burn with a so yellow

or orange ame or cause a re (ashback) at the air shuer beneath the control panel. To clean the inside

of the burner, it must be removed from the gas grill: Remove the screw that aaches the burner to the

back wall. Slide the burner back and upwards to remove. Cleaning: Use a exible venturi tube brush to

clean the inside of the burner. Shake any loose debris from the burner through the gas inlet. Check the

burner ports and valve orices for blockages. Burner ports can close over me due to cooking debris and

corrosion, use an opened paperclip or the supplied port maintenance bit to clean them. Drill out blocked

ports using this drill bit in a small cordless drill. The ports are easier to clean if the burner is removed from

Light Blue

Yellow Tipping

Dark Blue

Burner

Burner Port

Approximately

1/2” (13mm)

We recommend this gas grill be thoroughly inspected and serviced annually by a qualied service person.

At all mes keep the gas grill area free from combusble materials, gasoline and other ammable vapors

and liquids. Do not obstruct the ow of venlaon and combuson air. Keep the cylinder enclosure

venlaon openings (located on the cart sides and at the front and back of the boom shelf) free and

clear from debris.

N415-0326 JAN 16.19.indd 12 1/21/2019 3:49:41 PM

www.napoleongrills.com

N415-0326 JAN 16.19

WARNING! Regulator Hose (when applicable): Check for abrasions’, melng, cuts, and cracks in the

hose. If any of these condions exist, do not use the gas grill. Have the part replaced by your Napoleon

Gas Grill dealer or qualied gas installer.

WARNING! When reinstalling the burner aer cleaning it is very

important that the valve/orice enters the burner tube before lighng your

gas grill. If the valve is not inside the burner tube a re or explosion could

occur.

Aluminum Casngs: Clean casngs periodically with warm soapy water. Aluminum will not rust, but high

temperatures and weathering can cause oxidaon to occur on aluminum surfaces. This appears as white

spots on the casngs. To renish these areas, clean rst and sand lightly with ne sandpaper. Wipe the

surface to remove any residue and paint with high temperature barbecue paint. Protect surrounding areas

from over-spray. Follow the manufacture’s direcons for curing.

the grill, but it can also be done with the burner installed. Do not ex the drill bit when drilling the ports,

as this will cause the drill bit to break. This drill is for burner ports only, not for the brass orices (jets)

which regulate the ow into the burner. Take care not to enlarge the holes. Ensure the insect screen is

clean, ght, and free of any lint or other debris.

Reinstallaon: Reverse the procedure to reinstall the burner. Check that the valve enters the burner when

installing.

Infrared Burners: Because of the high intensity of the infrared burner, most drippings and food parcles

that fall onto the burner surface are immediately incinerated. However, some debris and residue may

remain. To remove this residue aer cooking, turn the grill on high with lid closed for 5-10 minutes. Do not

clean the ceramic le with a wire brush. If debris is collecng on your burner, simply light the burner and

operate on high for 5 minutes with the lid open, allowing debris to burn o. If the back burner is not used

oen, grease splaer from main burner grilling will eventually block the ports. Once a month, the back

burner should be red for 5-10 minutes to burn o the accumulated grease.

Protecon Of Infrared Burners: The infrared burners of your grill are designed to provide a long service

life, though care must taken to prevent cracking of their ceramic surfaces. Fractures will cause the burners

to malfuncon. The following provides a few of the causes of cracks and the steps you can take to avoid

them. Damage caused by failure to follow these steps is not covered by your grill warranty.

1. Impact with hard objects - Never allow hard objects to strike the ceramic. Take care when inserng or

removing cooking grates and accessories into or from the grill.

2. Contact with water or other liquids - Cold liquids contacng the hot ceramic surfaces can cause them

to break. Never throw water into the grill to douse a ame. If the ceramic or interior of a burner becomes

wet while not in use, later operaon of the burner can create steam, which can produce sucient

pressure to crack the ceramic. Repeated soaking of the ceramic can also cause it to swell and expand. This

expansion causes undue pressure on the ceramic that can cause it to crack and crumble.

i) Never throw water into the grill to control are-ups.

ii) Do not aempt to operate the infrared burners in open air while raining.

iii) If you nd standing water in your grill (because of exposure to rainfall, sprinklers, etc.), inspect

the ceramic for evidence of possible watersoaking. If the ceramic appears to be wet, remove

the burner from the grill. Turn it upside down to drain the excess water and bring indoors to dry

thoroughly.

3. Impaired venlaon of hot air from the grill - For the burners to funcon properly, hot air must have

a way to escape the grill. If the hot air is not allowed to escape, the burners can become deprived of

oxygen causing them to back-ash. If this occurs repeatedly, the ceramic could crack. Never cover more

than 75% of the cooking surface with solid metal (i.e., griddle or large pan).

4. Incorrect cleaning - Do not clean the ceramic le with a wire brush. If debris is collecng on your burner,

light the burner and operate on high for 5 minutes with the lid open, allowing debris to burn o.

REPLACEMENT SCREEN N565-0002

N415-0326 JAN 16.19.indd 13 1/21/2019 3:49:43 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Troubleshoong

Problem Possible Causes Soluon

Low heat / Low ame

when valve turned to

high.

For propane - improper lighng

procedure.

For natural gas - undersized

supply line.

For both gases - improper

preheang.

Ensure lighng procedure is followed carefully. All

gas grill valves must be in the o posion when the

tank valve is turned on. Turn tank on slowly to allow

pressure to equalize. See lighng instrucons.

Pipe must be sized according to installaon code.

Preheat grill with both main burners on high for 10

to 15 minutes.

Excessive are-ups/

uneven heat.

Sear plates installed incorrectly.

Improper preheang.

Excessive grease and ash build on

sear plates and in drip pan.

Ensure sear plates are installed with the holes

towards the front and the slots on the boom. See

assembly instrucons.

Preheat grill with both main burners on high for 10

to 15 minutes.

Clean sear plates and drip pan regularly. Do not

line pan with aluminum foil. Refer to cleaning

instrucons.

Burners burn with

yellow ame,

accompanied by the

smell of gas.

Possible spider web or other

debris, or improper air shuer

adjustment.

Thoroughly clean burner by removing. See general

maintenance instrucons. Open air shuer slightly

according to combuson air adjustment instrucons.

(This must be done by a qualied gas installer.)

Flames li away from

burner, accompanied

by the smell of gas, and

possibly dicules in

lighng.

Improper air shuer adjustment. Close air shuer slightly according to combuson

air adjustment instrucons. (This must be done by a

qualied gas installer.)

Rear and Side burners

will not light with the

igniter, but will light

with a match.

Dead baery / or installed

incorrectly.

Loose electrode wire or switch

terminal wires.

Liing ames on burner.

Replace with premium heavy duty baery.

Check that electrode wire is rmly pushed onto the

terminal on the back of the igniter. Check that the

lead wires from the module to the ignion switch (if

equipped) are rmly pushed onto their respecve

terminals.

Close air shuer slightly - see previous problem.

Main burner will not

light with the igniter,

but will light with a

match.

Jet-re outlet is dirty or clogged. Clean jet-re outlet with a so bristle brush.

Humming regulator. Normal occurrence on hot days. This is not a defect. It is caused by internal vibraons

in the regulator and does not aect the performance

or safety of the gas grill. Humming regulators will not

be replaced.

Burners will not cross

light each other.

Dirty or corroded cross light

brackets.

Clean or replace as required.

“Paint” appears to be

peeling inside lid or

hood.

Grease build-up on inside

surfaces.

This is not a defect. The nish on the lid and hood is

porcelain, and will not peel. The peeling is caused by

hardened grease, which dries into paint-like shards,

that ake o. Regular cleaning will prevent this. See

cleaning instrucons.

N415-0326 JAN 16.19.indd 14 1/21/2019 3:49:44 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Problem Possible Causes Soluon

Burner output on “high”

seng is too low.

(Rumbling noise and

uering blue ame at

burner surface.)

Lack of gas.

Supply hose is pinched.

Dirty or clogged orice.

Spider webs or other maer in

venturi tube.

Propane regulator in “low ow”

state.

Check gas level in propane cylinder.

Reposion supply hose as necessary.

Clean burner orice.

Clean out venturi tube.

Ensure lighng procedure is followed carefully. All

gas grill valves must be in the o posion when the

tank valve is turned on. Turn tank on slowly to allow

pressure to equalize. See lighng instrucons.

Infrared burner (if

equipped) ashes

back (during operaon

the burner abruptly

makes a loud “whoosh”

sound, followed by a

connuous blow-torch

type sound and grows

dim.)

Ceramic les overloaded with

grease drippings and build-up.

Ports are clogged.

Burner overheated due to

inadequate venlaon (too much

grill surface covered by griddle

or pan.)

Cracked ceramic le.

Leaking gasket surrounding the

ceramic le, or a weld failure in

the burner housing.

Turn burner o and allow to cool for at least two

minutes. Relight burner and burn on high for at least

ve minutes or unl the ceramic les are evenly

glowing red.

Ensure that no more than 75% of the grill surface

is covered by objects or accessories. Turn burner

o and allow to cool for at least two minutes, then

relight.

Allow burner to cool and inspect very closely

for cracks. If any cracks are found, contact your

authorized Napoleon dealer to order a replacement

burner assembly.

Contact your authorized Napoleon dealer for

instrucons on ordering a replacement burner

assembly.

N415-0326 JAN 16.19.indd 15 1/21/2019 3:49:44 PM

www.napoleongrills.com

N415-0326 JAN 16.19

KEEP YOUR RECEIPT AS PROOF OF PURCHASE TO VALIDATE YOUR WARRANTY.

Ordering Replacement Parts

Warranty Informaon

MODEL:

DATE OF PURCHASE:

SERIAL NUMBER:

(Record informaon here for easy reference)

For replacement parts and warranty claims, contact the Napoleon dealer where the product was purchased.

Before contacng the dealer, check the Napoleon Grills Website for more extensive cleaning, maintenance,

troubleshoong and parts replacement instrucons at www.napoleongrills.com.

To process a claim, the following informaon is required:

1. Model and serial number of the unit.

2. Part number and descripon.

3. A concise descripon of the problem (‘broken’ is not sucient).

4. Proof of purchase (photocopy of the invoice).

In some cases, Napoleon could request to have the parts returned to the factory for inspecon before

providing replacement parts.

Before contacng Napoleon dealer, please note that the following items are not covered by the warranty:

• Costs for transportaon, brokerage or export dues.

• Labour costs for removal and reinstallaon.

• Costs for service calls to diagnose problems.

• Discolouraon of stainless steel parts.

• Part failure due to lack of cleaning and maintenance, or use of improper cleaners (oven

cleaner or other harsh chemicals).

N415-0326 JAN 16.19.indd 16 1/21/2019 3:49:44 PM

www.napoleongrills.com

N415-0326 JAN 16.19

Geng Started

1. Remove all cart panels, hardware, and grill head from carton. Raise lid and remove any

components packed inside. Use the parts list to ensure all necessary parts are included.

2. Do not destroy packaging unl the grill has been fully assembled and operates to your sasfacon.

3. Assemble the grill where it is to be used, lay down cardboard or a towel to protect parts from being

lost or damaged while assembling.

4. Most stainless steel parts are supplied with a protecve plasc coang that must be removed

prior to using the grill. The protecve coang has been removed from some of the parts during the

manufacturing process and may have le behind a residue that can be perceived as scratches or

blemishes. To remove the residue, vigorously wipe the stainless steel in the same direcon as the

grain.

5. Follow all instrucons in the order that they are laid out in this manual.

6. Two people are required to li the grill head onto the assembled cart.

If you have any quesons about assembly or grill operaon, or if there are damaged or missing parts

please call our Customer Soluons Department at 1-866-820-8686 between 9 AM and 5 PM (Eastern

Standard Time).

CAUTION! During unpacking and assembly we recommended you wear work gloves and safety

glasses for your protecon. Although we make every eort to make the assembly process as problem

free and safe as possible, it is characterisc of fabricated steel parts that the edges and corners might

be sharp and could cause cuts if handled incorrectly.

TOOLS REQUIRED FOR ASSEMBLY (tools not included)

3/8” (10mm)

N415-0326 JAN 16.19.indd 17 1/21/2019 3:49:49 PM

www.napoleongrills.com

N415-0326 JAN 16.19

BUILT-IN UNIT OPENING DIMENSIONS

MODEL OPENING DIMENSIONS NOTES

W D H

BILEX730 43 1/4”

1099mm

21 3/8”

543mm

7 1/2”

191mm

SIDE

BURNER

12 3/4”

324mm

16 1/2”

419mm

4 1/2”

114mm

OPENING OF AT LEAST 5 SQ (32cm

) IN MUST BE PROVIDED FOR

COMBUSTION AIR FOR SIDE BURNER.

34” (864mm)

RECOMMENDED

MINIMUM 10 SQ IN (65cm

)

OF VENTILATION REQUIRED ON

EACH END OF CABINET

6” (152mm)

GAS INLET OPENING

OUTDOOR GFI ELECTRICAL OUTLET

REC

OMMENDED - LOCATE ON SAME SIDE

OF GRILL AS ROTISSERIE BRACKET.

1¾”

(44mm)

1¾”

(44mm)

BUILT-IN SIDEBURNER

GAS INLET OPENING

NON-COMBUSTIBLE MATERIAL

Note: Accessory frames

overlap opening by 1 ¾”

(4cm) on all 4 sides.

WARNING! CABINET FRAME, CABINET AND COUNTER TOP MUST BE MADE

FROM NON-COMBUSTIBLE MATERIAL.

WARNING! A propane tank can not be stored

below the gas grill.

WARNING! This grill is designed for Non-combusble enclosures only, and must be installed and

serviced by a qualied installer to local codes.

WARNING! Use only non-combusble materials (cered to ASTM E-136) such as steel studs,

cement board, ceramic le, marble, paint etc. When adding nishing materials to the appliance. Do not

use wood or drywall.

4” (101 mm)

ELECTRICAL CUTOUT

N415-0326 JAN 16.19.indd 18 1/21/2019 3:49:52 PM

www.napoleongrills.com

N415-0326 JAN 16.19

BUILT-IN ACCESSORY OPENING DIMENSIONS

PART # DESCRIPTION PICTURE W H D

N370-0361 PF STYLE STAINLESS STEEL DOOR 17” (432mm) 23 ¼” (591mm)

N370-0359 PF STYLE STAINLESS STEEL SINGLE

DRAWER

17 ¼” (438mm) 6 ¾” (171mm) 23” (584mm)

N370-0360 PF STYLE STAINLESS STEEL TRIPLE

DRAWER

17 ¼” (438mm) 22 ¾” (578mm) 23” (584mm)

N370-0502

N370-0503-1

DOUBLE DOOR SMALL

DOUBLE DOOR LARGE

* FRAMES PROTRUDE FROM FACE

OF CABINET BY ¾”

28 ¼” (718mm)

38 ¼” (959mm)

20 ¼” (514mm)

N370-0504

N370-0505

SIDE BURNER PROPANE

SIDE BURNER NATURAL

12 ¾” (324mm)

4 ½” (114mm)

minimum

16 ½” (419mm)

OPENING DIMENSIONS

N415-0326 JAN 16.19.indd 19 1/21/2019 3:49:52 PM

www.napoleongrills.com

N415-0326 JAN 16.19

BI ACCESSORY DRAWER INSTRUCTIONS

BI ACCESSORY DOOR INSTRUCTIONS

1. Unpack the drawer frame assembly.

2. Remove the drawers from the enclosure by fully extending them and then liing up to remove them

from the slides.

3. Shim the opening to ensure that the enclosure ts snuggly into the opening. Ensure that the side shims

are located at the same height as the enclosure mounng holes. The boom of the opening may need to

be shimmed as well to ensure that the front of the enclosure is plumb.

4. Once the enclosure is level and square, fasten into place. (Fasteners not included).

5. Re-install the drawers by pping the back of the drawer down into the slide. Once the wheels are

inserted into the slide, lower the front of the drawer unl it is level, then push in. Note: if the enclosure

is installed with shims that are too thick, the wheel will not engage into the slide. The shim thickness will

need to be reduced.

6. Remove the protecve coang from all remaining surfaces.

1. Unpack the door and frame.

a. For the curved stainless steel doors, remove the door(s) from the frame by liing the door while holding

on to the pivot rod. This will allow the pivot rod to come out of the hole on the boom of the frame. Once

the pivot is removed from the boom hole, the enre door can be dropped and removed from the frame.

b. For the PF style stainless steel door, the door needs to be removed by loosening the center philips screw

on the hinge furthest away from the door. This will allow the hinge to separate.

c. For double door kits N370-0502/N370-0503, refer to the instucons included with the door kit.

2. Center the frame in the opening. Mark the locaon of the pivot holes, top and boom. Remember on

the PT600 double doors, there will be a pivot rod on both ends. The PF style doors do not have pivot rods.

Once all pivot holes are marked, remove the frame and using a 3/8” drill bit, drill out the clearance holes

for the pivot rod. These clearance holes should be at least 1/2” deep. Aer the holes are complete, you

may once again center the frame in the opening. Starng with the hinged side, shim between the frame

and side wall of the opening. Ensure the shims are close to the hinge on the PF style doors. When the

frame side wall is plumb, fasten it to the cabinet with screws (not provided). Aach the other side of the

frame in the same fashion, ensuring the frame is square.

3. Other than on the curved stainless steel double door kit, fasteners are not required on the top and

boom of the frame. The curved stainless steel double door frame must be fastened in the center both at

the top and boom.

4. Once the frame has been secured and checked for squareness, the door can be re-installed.

5. Remove the protecve coang from all remaining surfaces.

N415-0326 JAN 16.19.indd 20 1/21/2019 3:49:52 PM

La page charge ...

NAPOLEON BILEX730RBIPSS Manuel utilisateur

Marque: NAPOLEON

Modèle: BILEX730RBIPSS

Catégorie: Barbecues

Taper: Manuel utilisateur

Ce manuel convient également à

BILEX730RBINSS

Télécharger le PDF

rapport

dans d''autres langues

English: NAPOLEON BILEX730RBIPSS User manual

NAPOLEON BILEX730RBIPSS Manuel utilisateur

Ce manuel convient également à

NAPOLEON BILEX730RBIPSS Manuel utilisateur

dans d''autres langues

Documents connexes