Campbell Hausfeld CHN10500 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: CHN10500

Catégorie: Cloueuse

Taper: Manuel utilisateur

Ce manuel convient également à

7/8 inch 23g

Micro Pin Nailer

Table of Contents

Description . . . . . . . . . . . . . . . . . . . . . 1

Unpacking . . . . . . . . . . . . . . . . . . . . . . 1

Safety Guidelines . . . . . . . . . . . . . . . . 1

Important Safety Information . . . . . . 1

Tool Components and

Specifications. . . . . . . . . . . . . . . . . . . . 2

Operating Instructions . . . . . . . . . . . . 4

Lubrication . . . . . . . . . . . . . . . . . . . . 4

Recommended Hookup. . . . . . . . . . 4

Operational Mode . . . . . . . . . . . . . . 5

Trigger Only Mode. . . . . . . . . . . . . . 5

Loading/Unloading The Tool. . . . . . 5

Adjusting Direction of Exhaust. . . . 5

Clearing A Jam From The Tool . . . . 5

User-Maintenance Instructions . . . . . 5

Interchange Information . . . . . . . . . . 6

Troubleshooting Chart . . . . . . . . . . . . 6

Warranty . . . . . . . . . . . . . . . . . . . . . . . 8

Description

This pin nailer is designed for tacking

decorative trim, glazing strips, small

picture frames and cabinetry trim.

Features include: adjustable exhaust,

narrow nose for fitting in tight spaces,

rubber comfort grip, auto-adjusting nail

height mechanism, and trigger lock.

Unpacking

After unpacking the unit, inspect

carefully for any damage that may

have occurred during transit. Make sure

to tighten fittings, bolts, etc., before

putting unit into service.

Model CHN10500

CALIFORNIA PROPOSITION 65

This product or

its power cord may

contain chemicals known to the State

of California to cause cancer and birth

defects or other reproductive harm.

Wash hands after handling.

You can create dust when

you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other

masonry. This dust often contains

chemicals known to cause cancer, birth

defects, or other reproductive harm.

Wear protective gear.

Safety Guidelines

This manual contains information

that is very important to know and

understand. This information is

provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help

recognize this information, observe the

following symbols.

Danger indicates an

imminently

hazardous situation which, if not

avoided, WILL result in death or serious

injury.

Warning indicates a

potentially

hazardous situation which, if not

avoided, COULD result in death or

serious injury.

Caution indicates a

potentially

hazardous situation which, if not

avoided, MAY result in minor or

moderate injury.

Notice indicates

important

information, that if not followed, may

cause damage to equipment.

NOTE: Information that requires special

attention.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A

RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS

This manual contains safety, operational

and maintenance information. Contact

your Campbell Hausfeld representative

if you have any questions.

When using tools,

basic precautions

should always be followed, including

the following:

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

IN726401AV 4/10

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions CHN10500

Locate model and date code on

tool and record below:

Model No.: _____________________

Date Code: _____________________

Retain these numbers for

future reference.

Campbell Hausfeld Tools meet or exceed Industries’ Standards as set forth by the American National Standard

Institute/International Staple, Nail and Tool Association in ANSI/ISANTA SNT-101-2002.

For parts, product & service information

visit www.chpower.com

GENERAL

a. To reduce the risks of

electric shock, fire, and

injury to persons, read all

the instructions before

using the tool.

b. Be thoroughly familiar with the

controls and the proper use of the

equipment. Follow all instructions.

Contact your Campbell Hausfeld

representative if you have any

questions.

c. Only persons well acquainted with

these rules of safe operation should

be allowed to use the unit.

Read and

understand tool

labels and manual. Failure to follow

warnings, dangers, and cautions could

result in DEATH or SERIOUS INJURY.

WORK AREA

a. Keep the work area clean and well

lighted. Cluttered benches and dark

areas increase the risks of electric

shock, fire, and injury to persons.

b. Do not operate the tool

in explosive atmospheres,

such as in the presence

of flammable liquids,

gases, or dust. The tool is

able to create sparks resulting in the

ignition of the dust or fumes.

c. Keep bystanders, children, and

visitors away while operating the

tool. Distractions are able to result in

the loss of control of the tool.

PERSONAL SAFETY

a. Stay alert. Watch what you are

doing and use common sense

when operating the tool. Do not

use the tool while tired or under

the influence of drugs, alcohol,

or medication. A moment of

inattention while operating the

tool increases the risk of injury to

persons.

b. Dress properly. Do not wear loose

clothing or jewelry. Contain long

hair. Keep hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long

hair increases the risk of injury to

persons as a result of being caught

in moving parts.

c. Avoid unintentional starting.

Be sure the switch is off before

connecting to the air supply. Do not

carry the tool with your finger on

the switch or connect the tool to the

air supply with the switch on.

d. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enables

Operating Instructions

Important Safety Instructions

(Continued)

better control of the tool in

unexpected situations.

e. Use safety equipment. A dust mask,

non-skid safety shoes and a hard

hat must be used for the applicable

conditions.

f. Always wear eye

protection.

g. Always wear hearing

protection when using

the tool. Prolonged

exposure to high intensity

noise is able to cause

hearing loss.

h. Do not attach the hose or tool to

your body. Attach the hose to the

structure to reduce the risk of loss of

balance if the hose shifts.

i. Always assume that the tool

contains fasteners. Do not point

the tool toward yourself or anyone

whether it contains fasteners or not.

not nail on

top of another nail. This is able to

cause the nail to be deflected and

hit someone, or cause the tool to

react and result in a risk of injury to

persons.

k. Remove finger

from the trigger

when not driving fasteners. Never

carry the tool with finger on trigger,

the tool is able to fire a fastener.

Tool Components and Specifications

 • REQUIRES: 0.15 SCFM with 10

fasteners per minute @ 90 psi

 •AIR INLET: 1/4 inch NPT

 • PIN SIZE RANGE: 3/8 inch to 7/8 inch

 • MAGAZINE CAPACITY:

110 headless pins, 23 g

 • WEIGHT: 1 lb. 13 oz.

 • LENGTH: 8.25 inches

 • HEIGHT: 6.8 inches

 • MAXIMUM PRESSURE: 100 psi

 • PRESSURE RANGE: 60 psi – 100 psi

Adjustable Exhaust

Trigger

Nail Loading Area

Nail Discharge

Area

Latch

Button

(other

side)

Magazine

Trigger Lock

Automatic Nail

Length Plate

www.chpower.com

Head Cap

air to remain in the tool. Death or

serious personal injury could occur.

Never place hands or any

other body parts in the

fastener discharge area of the

tool. The tool might eject a fastener and

could result in death or serious personal

injury.

Never carry the tool by

the air hose or pull the

hose to move the tool or

a compressor. Keep hoses

away from heat, oil and

sharp edges. Replace any hose that is

damaged, weak or worn. Personal injury

or tool damage could occur.

Always assume the

tool contains

fasteners. Respect the tool as a working

implement; no horseplay. Always keep

others at a safe distance from the work

area in case of accidental discharge of

fasteners. Do not point the tool toward

yourself or anyone whether it contains

fasteners or not. Accidental triggering

of the tool could result in death or

serious personal injury.

Do not drive a fastener

on top of other

fasteners. The fastener

could glance and cause

death or a serious puncture wound.

Do not operate or allow

anyone else to operate

the tool if any warnings

or warning labels are not legible.

Warnings or warning labels are located

on the tool magazine and body.

Do not drop or

throw the tool.

Dropping or throwing the tool can

result in damage that will make the tool

unusable or unsafe. If the tool has been

dropped or thrown, examine the tool

closely for bent, cracked or broken parts

and air leaks. STOP and repair before

using or serious injury could occur.

Avoid using the

tool when the

magazine is empty. Accelerated wear on

the tool may occur.

Clean and check all

air supply hoses

and ﬁttings before connecting the

tool to an air supply. Replace any

damaged or worn hoses or ﬁttings.

Tool performance or durability may be

reduced.

Always remain in a

ﬁrmly balanced

position when using or handling the

tool.

Avoid long extended

periods of work

with the tool. Stop using the tool if you

feel pain in hands or arms.

TOOL USE AND CARE

a. Use clamps or another practical way

to secure and support the workpiece

to a stable platform. Holding the

work by hand or against the body is

unstable and is able to lead to loss

of control.

b. Do not force the tool. Use the

correct tool for the application. The

correct tool will do the job better

and safer at the rate for which the

tool is designed.

c. Do not use the tool if the switch

does not turn the tool on or off. Any

tool that cannot be controlled with

the switch is dangerous and must be

repaired.

Disconnect the

tool from the air

source before making adjustments,

doing tool maintenance, clearing

jams, leaving work area,loading,

or unloading the tool. Such

precautionary measures reduce the

risk of injury to persons.

e. Store the tool when it is idle out

of reach of children and other

untrained persons. A tool is

dangerous in the hands of untrained

users.

f. Maintain the tool with care. Keep

a cutting tool sharp and clean. A

properly maintained tool, with sharp

cutting edges reduces the risk of

binding and is easier to control.

g. Check for misalignment or binding

of moving parts, breakage of parts,

and any other condition that affects

the tool’s operation. If damaged,

have the tool serviced before using.

Many accidents are caused by poorly

maintained tools. There is a risk of

bursting if the tool is damaged.

h. Use only those fasteners listed

in the Accessories section of this

manual. Fasteners not identified

for use with this tool by the tool

manufacturer are able to result in

a risk of injury to persons or tool

damage when used in this tool.

i. Selecting an appropriate tool

actuation system, taking into

consideration the work application

for which the tool is used.

Never use

gasoline

or other ﬂammable liquids

to clean the tool. Never use

the tool in the presence of

ﬂammable liquids or gases. Vapors

could ignite by a spark and cause an

explosion which will result in death or

serious personal injury.

Do not remove, tamper

with, or otherwise cause

the trigger lock or trigger

to become inoperable. Do

not operate any tool which has been

modiﬁed in a like fashion. Death or

serious personal injury could result.

Do not touch the trigger

unless driving fasteners.

Never attach air line to

tool or carry tool while

touching the trigger. The tool could

eject a fastener which will result in

death or serious personal injury. Also

actuate the trigger guard to the safe

position when not in use.

Always disconnect the

tool from the power

source when unattended,

performing any maintenance or repair,

clearing a jam, or moving the tool to a

new location. Do not load the tool with

fasteners when the trigger is depressed.

The tool could eject a fastener causing

death or serious personal injury.

Always ﬁt tool with a

ﬁtting or hose coupling

on or near the tool in

such a manner that all

compressed air in the tool is discharged

at the time the ﬁtting or hose coupling

is disconnected. Do not use a check

valve or any other ﬁtting which allows

CHN10500

Important Safety Instructions

(Continued)

WARNING

www.chpower.com

Operating Instructions

Important Safety Instructions

(Continued)

SERVICE

a. Tool service must be performed only

by qualified repair personnel.

b. When servicing a tool, use only

identical replacement parts. Use

only authorized parts.

c. Use only the lubricants supplied

with the tool or specified by the

manufacturer.

Do not make any

modiﬁcations to

the tool without ﬁrst obtaining written

approval from Campbell Hausfeld. Do

not use the tool if any shields or guards

are removed or altered. Do not use the

tool as a hammer. Personal injury or

tool damage may occur.

Disconnect air

supply and release

tension from the pusher before

attempting to clear jams because

fasteners can be ejected from the front

of the tool. Personal injury may occur.

AIR SOURCE

a. Never connect to an air source that

is capable of exceeding 200 psi.

Over pressurizing the tool is able

to result in bursting, abnormal

operation, breakage of the tool or

serious injury to persons. Use only

clean, dry, regulated compressed air

at the rated pressure or within the

rated pressure range as marked on

the tool. Always verify prior to using

the tool that the air source has been

adjusted to the rated air pressure or

within the rated air-pressure range.

b. Never use oxygen, carbon dioxide,

combustible gases or any bottled

gas as an air source for the tool.

Such gases are capable of explosion

and serious injury to persons.

Do not use any type of

reactive gases, including, but

not limited to, oxygen and

combustible gases, as a power source.

Use ﬁltered, lubricated, regulated

compressed air only. Use of a reactive

gas instead of compressed air may

cause the tool to explode which will

cause death or serious personal injury.

Use only a pressure-regulated

compressed air source to limit

the air pressure supplied to

the tool. The regulated pressure must

not exceed 100 psi. If the regulator

fails, the pressure delivered to the

tool must not exceed 200 psi. The tool

could explode which will cause death or

serious personal injury.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

OPERATING INSTRUCTIONS

LUBRICATION

This tool requires lubrication before

using the tool for the first time and

before each use. If an inline oiler is

used, manual lubrication through the

air inlet is not required on a daily basis.

The work surface

can become

damaged by excessive lubrication.

Proper lubrication is the owner’s

responsibility. Failure to lubricate the

tool properly will dramatically shorten

the life of the tool and void your

warranty.

1. Disconnect the air

supply from the tool

to add lubricant.

2. Turn the tool so the air

inlet is facing up. Place

4-5 drops of 30 W non-

detergent oil into air inlet.

Do not use detergent

oils, oil additives, or air- tool oils.

Air tool oils contain solvents which

will damage the tool's internal

components.

3. After adding oil, run

tool briefly. Wipe off

any excess oil from the

cap exhaust.

RECOMMENDED HOOKUP

The illustration below shows the

recommended hookup for the tool.

1. The air compressor

must be able to

maintain a minimum

of 60 psi when the

tool is being used. An inadequate air

supply can cause a loss of power and

inconsistent driving.

2. An oiler can be

used to provide oil

circulation through

the tool. A filter can

be used to remove

liquid and solid impurities which can

rust or “gum up” internal parts of

the tool.

3. Always use air supply hoses with

a minimum working pressure

rating equal to or greater than the

pressure from the power source if a

regulator fails, or 150 psi, whichever

OIL

100 psi

Recommended Hookup

Quick Plug

Quick

Coupler

Air Hose

Quick Plug

(Optional)

Quick

Coupler

(Optional)

Regulator

Lubricator Filter

60 psi

Min.

100 psi

Max.

www.chpower.com

CHN10500

OPERATING INSTRUCTIONS

(Continued)

is greater. Use 1/4 inch air hose for

runs up to 50 feet. Use 3/8 inch air

hoses for 50 foot run or longer.

4. Use a pressure regulator on the

compressor, with an operating

pressure of 0 psi - 125 psi. A pressure

regulator is required to control

the operating pressure of the tool

between 60 psi and 100 psi.

OPERATIONAL MODE

Always know the

operational mode of

the tool before using. Failure to know

the operational mode could result in

death or serious personal injury.

TRIGGER ONLY MODE (WITH

TRIGGER LOCK)

The tool is a single-actuator device. This

mode requires that, with the trigger

lock not positioned in the safe mode,

only a pull of the trigger will fire a

fastener.

After verifying there are no fasteners

in the tool, safety check the operation

of the activated trigger lock to prevent

the tool from firing a fastener before

storage. Always disconnect from

compressed air when not in use.

LOADING/UNLOADING THE TOOL

1. Always disconnect the tool from

the air supply before loading

fasteners.

2. Push the latch button.

Pull back on the

magazine cover fully.

3. Insert a stick of

fasteners into the

magazine under the

automatic nail length

plate. Make sure

pointed ends of pins are resting on

bottom ledge of magazine when

loading. Make sure pins are not dirty

or damaged. Pins are marked for

direction of loading.

4. Push the magazine

cover forward until

latch engages.

5. Always unload all fasteners before

removing tool from service.

Unloading is the reverse of loading,

except always disconnect the air

supply before unloading.

ADJUSTING THE DIRECTION OF THE

EXHAUST

The tool is

equipped with an

adjustable direction

exhaust deflector. This is intended to

allow the user to change the direction

of the exhaust. Simply twist the

deflector to any direction desired.

CLEARING A JAM FROM THE TOOL

1. Disconnect the air

supply from the tool.

2. Remove all nails from the magazine

(see "Loading/ Unloading The

Nailer"). Failure to do so will cause

the nails to eject from the front of

the nailer.

3. Completely remove the two (2) small

nose screws and the top nose plate

to reveal the jammed fastener.

4. Using caution not to bend or

damage the driver blade, use a pick

or some other pointed object to pry

free and clear the jammed fastener.

USER-MAINTENANCE

INSTRUCTIONS

TECHNICAL SERVICE

Please call our Tool Hotline at 1-800-

543-6400 with any questions regarding

the operation or repair of this tool or

for additional copies of this manual.

FASTENER AND REPLACEMENT

PARTS

Use only 23 gauge

headless micropins

(or equivalent - see Fastener

Interchange Information). Tool

performance, safety and durability

could be reduced if improper fasteners

are used. When ordering replacement

parts or fasteners, specify by part

number.

TOOL REPAIR

Only qualified personnel should repair

the tool and they should use genuine

Campbell Hausfeld replacement parts

and accessories, or parts and accessories

which perform equivalently.

DRIVER BLADE CARE AND

REPLACEMENT

In order to properly drive the

tiny micropins and leave a nearly

undetectable hole, the tips of the driver

blades end in a fine point and are

therefore quite vulnerable to abuse and

extended use.

To maximize the life of the blade,

closely examine fasteners for defects.

Do not use defective or improper

fasteners. Also load fasteners in the

proper orientation; the pin points and

the arrows always point toward the

wood surface. Drive fasteners into wood

products only (see "Loading/ Unloading

The Nailer").

Even with good care, extended use

of the tool may eventually lead to tip

failure. Replacement driver assemblies

can be purchased by calling 1-800-

543-6400 and refer to part number

SKN12600AV.

Latch

Button

150 psi or greater

3/8 inch I.D.

Rotate

LockUnlock

www.chpower.com

Symptom Possible Cause(s) Corrective Action

Air leaking at trigger valve

area.

O-Rings in trigger valve housing are

damaged

Replace o-rings

Air leaking between housing

and nose.

1. Damaged o-rings 1. Replace o-rings

2. Damage to bumper 2. Replace bumper

Air leaking between housing

and cap.

1. Loose screws 1. Tighten screws

2. Damaged seal 2. Replace seal

Tool skips driving fastener 1. Worn bumper 1. Replace bumper

2. Dirt in nose piece 2. Clean drive channel

3. Dirt or damage prevent fasteners or

pusher from moving freely in magazine

3. Clean magazine

4. Damaged pusher spring 4. Replace spring

5. Inadequate air flow to tool 5. Check fitting, hose, or compressor

6. Worn o-rings on piston or lack of

lubrication

6. Replace and lubricate o-rings

7. Damaged o-rings on trigger valve 7. Replace o-rings

8. Air leaks 8. Tighten screws and fittings

9. Cap seal leaking 9. Replace seal

10. Defect in automatic nail length plate 10. Clear problem with plate

Tool runs slow or has loss of

power

1. Tool not lubricated sufficiently 1. Lubricate nailer

2. Broken spring in cylinder cap 2. Replace spring

3. Exhaust port in cap is blocked 3. Replace damaged internal parts

Fasteners are jammed in tool 1. Guide on driver is worn 1. Replace guide

2. Fasteners are not correct size 2. Use only recommended fasteners

3. Fasteners are bent 3. Replace with undamaged fasteners

4. Magazine or nose screws are loose 4. Tighten screws

5. Driver is damaged 5. Replace driver

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur.

Any repairs or replacements must be done by a Qualiﬁed Service Person or Authorized Service Center.

Operating Instructions

USER-MAINTENANCE

INSTRUCTIONS (CONTINUED)

Replace assembly by first removing

the four (4) head cap screws using the

3 mm hex wrench provided. Remove

head cap and components to access the

driver piston. Remove and replace driver

assembly using your fingers. Replace

components and head cap as removed.

ASSEMBLY PROCEDURE FOR SEALS

When repairing a tool, the internal

parts must be cleaned and lubricated.

Parker O-lube or equivalent must be

used on all o-rings. Each o-ring must be

coated with O-lube before assembling.

A small amount of oil must be used on

all moving surfaces and pivots. After

reassembling, a few drops of 30W

non-detergent oil or equivalent, must

be added through the air line before

testing.

STORAGE

The tool should be stored in a cool dry

place.

Interchange Information

Can use 3/8 inch to 7/8 inch pins

from the following branded 23 g

micropinners: Senco FP10, Air Locker

P630, Porter Cable PIN100, Grex P635,

and Max NF235A.

www.chpower.com

CHN10500

Notes

www.chpower.com

Operating Instructions

www.chpower.com

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison,

Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell

Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld nailer or stapler.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the

duration of the warranty period with the exceptions below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM

THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial

or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow

limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the

exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to

you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance

with instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser’s abuse, neglect or

failure to operate products in accordance with instructions shall also include the removal or alteration of any safety

devices. If such safety devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E. Items or service that are normally required to maintain the product, e.g. o-rings, springs, bumpers, debris shield,

driver blades, gaskets, packings or seals, lubricants, or any other expendable part not specifically listed. These items

will only be covered for ninety (90) days from date of original purchase. Underlined items are warranted for defects

in material and workmanship only.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or

components which are defective, have malfunctioned and/or failed to conform within the duration of the specific

warranty period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options. Freight costs must be borne by the

purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be

scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of

replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also

have other rights which vary from state to state or country to country.

Table des matières

Descripion . . . . . . . . . . . . . . . . . . . . 1-Fr

Déballage . . . . . . . . . . . . . . . . . . . . 1-Fr

Directives de sécurité . . . . . . . . . . . 1-Fr

Importantes instructions

de sécurité . . . . . . . . . . . . . . . . . . . . 1-Fr

Pièces détachées et fisch technique

mécanisme de la l'outil. . . . . . . . . . 2-Fr

Mode d’emploi . . . . . . . . . . . . . . . . 4-Fr

Graissage . . . . . . . . . . . . . . . . . . . 4-Fr

Branchement recommandé. . . . . 4-Fr

Mode d’opération . . . . . . . . . . . . 5-Fr

Mode séquentiel unique . . . . . . . 5-Fr

Chargement/décharement de

l'outil. . . . . . . . . . . . . . . . . . . . . . . 5-Fr

Ajustement de la direction

d'échappement . . . . . . . . . . . . . . 5-Fr

Déblocage de la l'outil . . . . . . . . 5-Fr

Instructions de maintenance

de l'utilisateur . . . . . . . . . . . . . . . . . 5-Fr

Information d'interchangeabilité . 6-Fr

Guide de dépannage . . . . . . . . . . . 7-Fr

Garantie limitée . . . . . . . . . . . . . . . 8-Fr

Description

Cette cloueuse de pointes est conçue

pour l’installation de garnitures

décoratives, bandes de vitrage, petits

cadres et garniture d’armoires. Les

caractéristiques incluent : échappement

réglable, buse étroite pour les endroits

restreints, prise confort de caoutchouc,

mécanisme de hauteur de clou

autoajustable et verrou de gâchette.

Déballage

Dès que l’appareil est déballé,

l’inspecter attentivement pour tout

signe de dommages en transit. S’assurer

de resserrer tous les raccords, boulons,

etc. avant de le mettre en service.

PROPOSITION 65 DE CALIFORNIE

Ce produit ou son

cordon peuvent

contenir des produits chimiques qui, de

l’avis de l’État de Californie, causent le

cancer et des anomalies congénitales

ou autres problèmes de reproduction.

Lavez-vous les mains après la

manipulation.

Vous pouvez créer de la

poussière en coupant,

ponçant, perçant ou

meulant les matériaux tels que le

bois, la peinture, le métal, le béton,

le ciment ou autre maçonnerie. Cette

poussière contient souvent des produits

chimiques reconnus pour causer le

cancer, les déformations congénitales

ou autres problèmes de la reproduction.

Porter de l’équipement de protection.

Directives de Sécurité

Ce manuel contient de l’information

très importante qui est fournie pour

la SÉCURITÉ et pour ÉVITER LES

PROBLÈMES D’ÉQUIPEMENT. Rechercher

les symboles suivants pour cette

information.

Danger indique une

situation

hasardeuse imminente qui RÉSULTERA

en perte de vie ou blessures graves.

Avertissement

indique une

situation hasardeuse potentielle

qui PEUT résulter en perte de vie ou

blessures graves.

Attention indique

une situation

hasardeuse potentielle qui PEUT résulter

en blessures.

Avis indique de

l’information

importante pour éviter le dommage de

l’équipement.

REMARQUE : L’information qui exige

une attention spéciale.

Importantes instructions

de sécurité

INSTRUCTIONS PORTANT SUR UN

RISQUE D’INCENDIE, UN CHOC

ÉLECTRIQUE OU DES BLESSURES

AUX PERSONNES

Ce manuel contient des informations

concernant la sécurité, le

fonctionnement et l’entretien.

Contacter votre représentant Campbell

Hausfeld si vous avez des questions.

En utilisant les

outils, il faut suivre

les précautions de base, y compris ce

qui suit :

Veuillez lire et conserver ces instructions. Lire attentivement avant de commencer à assembler, installer, faire fonctionner ou entretenir

l'appareil décrit. Protégez-vous et les autres en observant toutes les informations sur la sécurité. Négliger d'appliquer ces instructions peut

résulter en des blessures corporelles et/ou en des dommages matériels ! Conserver ces instructions pour références ultérieures.

IN726401AV 4/10

Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.

1-Fr

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

Trouver le numéro de modèle et

le code date sur le chargeur de

l’outil et inscrire plus bas :

du Model : __________________

Code de date : __________________

Conserver ces numéros

comme référence.

Les outils Campbell Hausfeld satisfont ou dépassent les normes de l’industrie tel qu’indiqué par l’American

National Standard Institute/International Staple, Nail and Tool Association sous ANSI/ISANTA SNT-101-2002.

Cloueuse de micro

pointes de

22,2 mm (7/8 po)

Instructions d’Utilisation CHN10500

Modèle CHN10500