Conair MN252CSC Manuel utilisateur

Catégorie
Tondeuses à barbe
Taper
Manuel utilisateur
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety pre-
cautions should always be taken, including
the following:
READ ALL INSTRUCTIONS
BEFORE USING
KEEP AWAY FROM WATER
DANGER–Any appliance is electri-
cally live, even when the switch is off.
To reduce the risk of death or injury by
electric shock:
1. Always unplug appliance from electrical
outlet immediately after using (except
when charging unit) and before cleaning.
2. Do not place or store appliance where it
can fall or be pulled into a tub or sink.
3. Do not use appliance while bathing or in
the shower.
4. Do not place appliance in, or drop into
water or other liquid.
5. If appliance has fallen into water, do not
reach for it. Unplug immediately.
DO NOT REACH
INTO THE WATER
WARNING– To reduce the risk
of burns, electric shock, fire, or injury to per-
sons:
1. Never leave a plugged-in appliance
unattended.
2. This appliance should not be used by, on,
or near children or individuals with certain
disabilities.
3. Use appliance only for its intended use as
described in this manual. Only use attach-
ments recommended by the manufacturer.
Do not use an extension cord to operate
the appliance.
4. Never operate the appliance if it has a dam-
aged cord or plug, is not working
properly, has been dropped or damaged,
or dropped into water. Return the appli-
ance to a Conair service centre for exami-
nation and repair.
5. Keep the appliance cord away from
heated surfaces.
6. Do not pull, twist or wrap the cord around
the appliance.
7. Never drop or insert any object into any
opening of the appliance.
8. Do not place the appliance on any surface
while it is operating.
9. Do not use the appliance with a damaged
or broken comb or with teeth missing
from the blades, as injury may result.
Before each use, make certain the blades
are aligned properly and oiled.
10. Do not use the appliance outdoors or
operate where aerosol (spray) products
are being used or oxygen is being admin-
istered.
11. This product is for household use only.
SAVE THESE
INSTRUCTIONS
TROUBLESHOOTING
There are several things to look for if your
trimmer fails to operate:
1. Be sure the trimmer is turned ON.
2. Check the blades to see if they are clogged
with hair clippings; if so, use the cleaning
brush to remove hair.
3. If the trimmer still fails to operate, take or
send it to a Conair Service Centre (see
warranty procedure and addresses).
If your rechargeable trimmer does not
seem to be taking a charge, take the
following troubleshooting steps before
returning it for repair:
1. Be sure the electrical outlet is working, by
plugging in another appliance to test it.
2. Make sure the electrical plug is not
connected to a switch which turns power
off when lights are turned off.
3. Be sure you have inserted the trimmer
properly into the charging stand, that all
connections are secure, and that the
trimmer switch is in the “OFF” position.
FOR HOUSEHOLD
USE ONLY
OPERATING
INSTRUCTIONS
FOR YOUR RECHARGEABLE
TRIMMER
Check to be sure which model
you have purchased.
1. Before using your trimmer for the first
time, insert the trimmer in the charging
base and then plug into wall outlet and
charge it for 16 hours. Always place the
trimmer in the stand with the ON/OFF
switch in the OFF position. Attempting to
charge the unit in the ON position can
cause damage to the unit and it will not
charge.
2. Always check to see if the charging light is
on when the cord is connected to the trim-
mer and the unit is not in use.
3. Plug unit into any 120V, 60Hz wall outlet.
4. The trimmer can remain plugged into the
power source at all times without damage
to the battery.
5. To use your trimmer, push ON/OFF switch
upwards to “ON” position.
6. After you finish using your trimmer, push
down on the ON/OFF switch to turn the
trimmer off.
7. If, while trimmer is in use, the charge
seems to be running down, simply put
ON/OFF switch in OFF position. Then,
insert the trimmer in the charging base
and plug into wall outlet. Allow battery to
recharge for several hours.
8. To maintain the full charging capacity and
extend the life of the battery, it must be
periodically run down during normal use
until it stops, then recharge.
9. The charge base may become warm while
charging – this is normal.
10. To charge the unit when traveling, you do
not need to take the stand with you. Just
plug the cord directly into the unit and the
unit will begin charging. (Remember
switch must be in the “OFF” position,
Remove the battery cap and push the
batteries out. Bring the batteries to the
nearest collection centre for proper disposal.
DO NOT throw the battery into the normal
municipal waste system.
TURBO FEATURE
This product is equipped with a turbo boost
button. When activated, this will proved 15%
more cutting power. This is especially useful
for cutting through thicker hair.
To activate the turbo feature:
1. Turbo the power switch to the “ON” position
2. Press the Turbo button, it is the round
button located on the side of the trimmer
3. Continue to press the Turbo button for as
long as you need the extra power
4. Release the Turbo button to return to
normal power
PIVOTING HEAD
To make it easier to trim hard to
reach areas, the trimmer has a
multi position pivoting head.
To pivot the head:
1. Press the release but-
tons on the side of the
trimmer and rotate the
pivoting head. (see image)
2. Press bottom of the
trimmer head until it clicks
into the position that is most comfortable for
trimming your face.
TYPES OF BEARDS/MUSTACHES
GROWING A BEARD OR MUSTACHE
There are three key factors that determine
which beard or
mustache style is
most suitable for
your face:
1. The shape and
dimensions of
your face.
2. The natural growth of your beard/
mustache.
3. The thickness of your beard/mustache.
If you are unsure of the type of beard or mus-
tache that most suits your face, speak with a
professional hair stylist and ask for an opin-
ion on what style would be best. Once your
beard or mustache has been styled, it is
essential that you maintain its appearance. To
do this, use your shaper to trim your
beard/mustache weekly.
For the best trimming results, your beard
should be slightly damp (not wet) before
using the trimmer. This will prevent
the trimmer from removing more hair
than desired.
GETTING STARTED
TO SWITCH TRIMMER HEADS
Hold the trimmer handle with the back of the
trimmer facing you.
Attach the beard trim-
mer head by aligning
both arrows on the foil
frame and on the head
until it clicks into
place. (Fig.1)
Attach another head by pushing it down on
the top of the trimmer until it snaps into place.
USING THE SHAVER
ATTACHMENT
Attach the foil shaver head by
snapping it in place. Turn unit
on. Gently press the foil head
against your skin where you
want to completely shave the
skin clean. Gently pull your skin
taught and move the shaver in a circular
motion over your skin.
When you are finished, or if you have a lot of
stubble to remove, press the release buttons
on the side of the shaver head (see cleaning
instructions) and gently pull the foil assembly
off. Clean the cutter and foil using the brush.
Reattach the foil head.
BATTERY REMOVAL
CONTAINS NICKEL CADMIUM
BATTERY. MUST BE COLLECTED,
RECYCLED OR DISPOSED OF
PROPERLY. DO NOT DISPOSE OF
IN THE MUNICIPAL WASTE.
Fig. 1
CONSIGNES
IMPORTANTES
L’utilisation d’appareils électriques, surtout en
présence d’enfants, demande la prise de
précautions élémentaires, dont les suivantes :
LIRE TOUTES LES
DIRECTIVES AVANT
L’UTILISATION
TENIR LOIN DE L’EAU
DANGER–
Un appareil est sous tension même s’il est
éteint. Afin de réduire lr sique de mort ou de
blessure par choc électrique :
1. Déconnectez-le de la prise de courant
immédiatement après l’usage (sauf pen-
dant la charge) et avant le nettoyage.
2. Ne le placez pas et ne le rangez pas là où il
peut tomber ou être tiré dans un évier ou
une baignoire.
3. Ne l’utilisez pas en prenant un bain ou une
douche.
4. Ne le placez pas et ne l’échappez pas dans
l’eau ou un liquide.
5. S’il tombe dans l’eau, ne le saisissez pas.
Déconnectez-le immédiatement.
N’ALLEZ PAS SAISIR UN
APPAREIL TOMBÉ DANS L’EAU
AVERTISSEMENT–
Afin de réduire le risque de brûlure, d’incendie,
de choc électrique ou de blessure :
1. Ne laissez jamais l’appareil branché sans sur-
veillance.
2. L’appareil ne doit pas être utilisé par, sur ou
près d’enfants ou de personnes souffrant de
certaines infirmités.
3. Ne l’utilisez que pour l’usage prévu indiqué
dans ce livret. N’utilisez que les accessoires
recommandés par le fabricant. Ne l’utilisez
pas avec une rallonge.
4. Ne l’utilisez pas avec un fil ou une fiche
endommagée, s’il a été échappé ou brisé ou
s’il est tombé dans l’eau. retournez-le au
service après-vente Conair où il sera inspecté
et réparé.
5. Gardez le fil loin des surfaces chauffées.
6. Ne tirez ni ne tordez le fil et ne l’enroulez pas
autour de l’appareil.
7. N’échappez ni n’insérez aucun objet dans les
ouvertures.
8. Ne le déposez pas sur une surface alors qu’il
est en marche.
9. Ne l’utilisez pas avec un peigne cassé ou
endommagé ni s’il manque des dents aux
lames car vous risquez de vous blesser.
Assurez-vous que les lames sont bien
alignées et huilées avant chaque usage.
10. Ne l’utilisez pas à l’extérieur ni là où l’on
utilise des aérosols ou administre de
l’oxygène.
11. L’appareil est réservé à l’usage ménager.
CONSERVEZ CES
DIRECTIVES
DÉPISTAGE DES PROBLÈMES
Si l’appareil ne fonctionne pas, effectuez les
vérifications suivantes :
1. Assurez-vous qu’elle est allumée (ON).
2. Assurez-vous que les lames sont propres; si
elles sont embourbées, nettoyez-les avec la
brosse de nettoyage.
3. Si la tondeuse ne fonctionne toujours pas,
présentez-la au service après-vente de
Conair (procédure et adresse dans le texte de
la garantie).
Si la tondeuse rechargeable ne semble pas se
charger, procédez comme suit avant de la
présenter au service après-vente :
1. Assurez-vous que la prise de courant est
sous tension en y branchant un autre
appareil.
2. Assurez-vous que la prise n’est pas com-
mandée par un interrupteur qui coupe le
courant quand vous éteignez les lumières.
3. Assurez-vous de bien placer la tondeuse sur
le support chargeur afin d’assurer un bon
contact, et de régler l’interrupteur sur OFF.
RÉSERVÉ À L’USAGE
MÉNAGER
DIRECTIVES
D’UTILISATION
TONDEUSE RECHARGEABLE
Vérifiez quel modèle vous avez
acheté
1. Avant d’utiliser la tondeuse la première
fois, placez-la sur le socle chargeur et
branchez-le dans une prise de courant.
Chargez-la pendant 16 heures. Placez
toujours la tondeuse sur le socle, l’inter-
rupteur en position d’arrêt (OFF). Tenter
de charger la tondeuse en marche peut
l’endommager et elle ne se chargera pas.
2. Vérifiez toujours si le témoin de charge
s’allume quand le fil est connecté à la ton-
deuse et qu’elle n’est pas en service.
3. Connectez-la dans une prise 120 V, 60 Hz.
4. La tondeuse peut être laissée branchée
dans la prise de courant en tout temps,
sans dommage à la pile.
5. Pour l’utiliser, poussez l’interrupteur en
position de marche (ON).
6. Après l’utilisation, réglez l’interrupteur en
position d’arrêt (OFF).
7. Si, en cours d’usage, la tondeuse semble
ralentir, éteignez-la puis placez-la sur le
socle chargeur. Branchez le socle dans
une prise de courant et laissez la pile
charger pendant quelques heures.
8. Pour maintenir la pleine capacité de
charge et prolonger la durée de la pile,
laissez la tondeuse fonctionner jusqu’à ce
qu’elle s’arrête puis rechargez-la.
9. Le socle chargeur peut devenir chaud en
cours d’usage; cela est normal.
10. Pour charger la tondeuse en voyage,
vous n’avez pas à emporter le socle
chargeur. Branchez le fil directement
dans la tondeuse et elle se chargera
(n’oubliez pas de mettre l’interrupteur en
position d’arrêt).
Enlevez le capuchon et faites sortir les piles.
Apportez les piles à un centre de collecte.
NE LES JETEZ PAS avec les ordures
ménagères.
FONCTION TURBO
La tondeuse possède une fonction turbo qui
accroît sa puissance de 15 % quand elle est
engagée. La fonction est pratique pour la
tonte de cheveux très épais.
Pour l’utiliser :
1. Mettez la tondeuse en marche.
2. Appuyez sur le bouton Turbo rond situé
sur le côté de la tondeuse.
3. Tenez le bouton Turbo enfoncé tant que
vous voulez utiliser la fonction.
4. Relâchez le bouton Turbo pour retourner à
la puissance normale.
TÊTE PIVOTANTE
Pour mieux atteindre les
endroits difficiles à couper, on
peut faire pivoter la tête sur
plusieurs positions :
1. Appuyez sur les boutons
de dégagement de part et
d’autre de la tête et inclinez
la tête (voir l’illustration).
2. Poussez le bas de la tête
jusqu’à ce qu’elle s’en-
clique dans la position la plus confortable
pour la tonte des poils.
TYPES DE BARBES/MOUSTACHES
Il y a trois principaux facteurs à considérer
pour établir quelle barbe ou moustache con-
vient le mieux à
votre visage :
1. La forme et la
dimension du
visage.
2. La croissance
naturelle de la
barbe ou de la
moustache.
3. L’épaisseur des poils.
Si vous n’êtes pas certain du type de barbe
ou de moustache qui vous convient le mieux,
parlez-en à un coiffeur et demandez-lui son
opinion. Une fois que votre barbe ou que
votre moustache a été taillée, il est essentiel
que vous en mainteniez l’apparence. Pour ce
faire, utilisez la lame de découpe chaque
semaine pour tailler votre barbe/moustache.
Pour de meilleurs résultats, la barbe devrait
être humide (pas mouillée) avant de tondre.
Vous éviterez ainsi de couper plus de poils
que désiré.
TOUT D’ABORD
CHANGER LA TÊTE DE COUPE
Tenez la tondeuse, le dos vers vous.
Posez la tête pour la
barbe en alignant la
flèche de la grille avec
celle de le la tête et
encliquez (ill. 1).
Posez une autre tête en
procédant de même,
l’enclenchant bien en position.
UTILISATION DU RASOIR
Posez la tête de rasoir en l’en-
clenchant en place. Mettez l’ap-
pareil en marche. Pressez la
grille légèrement contre le vis-
age, là où vous voulez rasez les
poils complètement. Tendez la
peau en douceur et déplacez la tondeuse
dans un mouvement circulaire sur la peau.
Une fois que vous avez terminé, ou si vous
avez beaucoup de poils à couper, appuyez
sur les boutons de dégagement de part et
d’autre de la tête (voir les directives de net-
toyage) et tirez doucement sur la grille.
Nettoyez les lames et la grille avec la petite
brosse puis remettez la grille en place.
REMPLACEMENT DE LA PILE
PILE NICKEL-CADMIUM. CETTE PILE
DOIT ÊTRE RAMASSÉE, RECYCLÉE OU
JETÉE CORRECTEMENT. NE LA JETEZ
PAS AVEC LES ORDURES MÉNAGÈRES.
Ill. 1
Conair wants to thank you for choosing our
beard/mustache trimmer. We know it will
provide you with years of reliable service.
®
TO TRIM YOUR MUSTACHE
1. For best results, start with a clean, slightly
damp mustache.
2. Comb through your mustache in the direc-
tion it grows.
3. Place the multi position comb over the trim-
mer blades and snap it into posi-
tion. It is a good idea to start with
the longest trim setting adjust-
ment. (You can always go back
and cut your mustache more
closely with a shorter setting.)
ALWAYS TRIM YOUR MUSTACHE
FROM THE TOP DOWN
After your mustache has been trimmed to the
desired length, remove the trimming attach-
ment and, using the blades only, define the out-
line of the bottom of your mustache.
USING THE SCRIBE BLADE
The scribe blade is used for fine detailing of your
facial hair. After trimming the hair to the desired
length, us the scribe blade to make fine line
details, the narrow blade width is perfect for
detailing under your lips or along the jaw line
1. Attach the scribe blade head
2. Move the ON/OFF switch to the on position
3. Press the tip of the scribe blade against your
skin and move the blade to create the desired
detail to your facial hair.
4. When finished detailing, move the ON/OFF
switch to the OFF position.
5. Use the supplied brush to clean away hairs.
6. Return the trimmer to the charging stand in
between uses
TAKING CARE OF YOUR TRIMMER
BLADE CARE
Cleaning Beard Trimmer
The head can be opened for cleaning purpose by
pressing the button at the bottom of head.
(Fig.2) The cover will be opened.
Shaver Head
To clean the shaver blade and foil:
1. Press both foil frame release buttons
(Fig.5). Then remove the shaver head (the cut-
ter is now in view). Be careful not to push on
the foil as it is delicate and can be easily dam-
aged.
2. Clean the cutter and the surrounding areas
with the brush provided (Fig.6). Rinse the
shaver foil frame under running water.
3. After rinsing, allow the foil frame to air-dry
before closing foil frame. Be sure to align both
arrows on the foil frame and on the head until
it clicks into place.
4. Hold the cutter firmly and guide it gently
04CN1217 IB-5426
1. Beard Trimmer
2. On/Off Switch on Body
3. Battery Compartment
4. Long Comb Attachment
5. Short Comb Attachment
6. Shaver
7. Scribe Blade
8. Recharging/Storage Base
9. Cleaning Brush
10. Mustache Comb
11. Lubricating Oil
LIMITED TWO YEAR WARRANTY
Conair will repair or replace (at our option) your unit
free of charge for 24 months from the date
of purchase if the appliance is defective in work-
manship or materials.
To obtain service under this warranty, return the
defective product to the service centre listed below
that is nearest you, together with your purchase
receipt and $5.50 for postage and handling. In the
absence of a purchase receipt, the warranty period
shall be 24 months from the date of manufacture.
ANY IMPLIED WARRANTIES, OBLIGATIONS, OR
LIABILITIES, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTY OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED IN DURATION TO THE
24 MONTH DURATION OF THIS WRITTEN, LIM-
ITED WARRANTY.
IN NO EVENT SHALL CONAIR BE LIABLE FOR ANY
SPECIAL, INCIDENTAL, OR CONSEQUEN-
TIAL DAMAGES FOR BREACH OF THIS OR ANY
OTHER WARRANTY, EXPRESS OR IMPLIED,
WHATSOEVER.
This warranty gives you specific legal rights, and
you may also have other rights, which vary from
province to province.
Service Centre:
Conair Consumer Products Inc.
Service Department
156 Parkshore Drive
Brampton, Ontario L6T 5M1
1-800-472-7606
Visit us on the web at: www.conaircanada.ca
©2004 CONAIR CONSUMER PRODUCTS INC.
156 Parkshore Drive
Brampton, Ontario L6T 5M1
OUTLINING YOUR BEARD
1.It is always best to begin with a clean, slight-
ly damp beard.
2. After you have combed through your beard in
the direction it grows naturally, you will want
to outline the desired shape, beginning under
your jawline.
3. Attach the beard trimmer head. Begin defin-
ing your beard’s shape under your chin and
work upward on each side of your face
toward your ears. Then define the upper out-
line of your beard across your cheeks, past
your sideburns and toward your hairline.
NOW YOU’RE READY
TO TRIM YOUR BEARD
There are 2 multi position combs for cutting dif-
ferent lengths of hair. One for shorter lengths
and one for longer lengths.
1. To use the multi position comb, slide it over
the trimmer blades and snap down into posi-
tion. At first, until you become familiar with
the adjustments, use the longest comb and
trim setting. (You can
always go back and
make your beard a lit-
tle shorter.)
2. Begin trimming your
beard using smooth,
even strokes. Start with your sideburns and
work downward toward your chin. (Never
attempt to trim against the natural growth of
your beard, because the hair will be cut too
short.)
3. If you decide you want a closer
trim, you can now adjust the
multi position comb to a short-
er setting and go over your
beard again until you achieve
the desired length.
3
Position Pivoting Head
into the cutter mount. Press firmly until the
cutter snaps into place.
Caution: make sure you do not lose the little
spring under the cutter.
Because the trimmer blades are precision made
for a very special use, they should always be
handled with care. Each time you finish using the
trimmer, take the cleaning brush provided and
brush away any loose hair that has collected in
the blades. Then store the trimmer in its storage
stand until the next use.
To promote the long life of the appliance, use
your trimmer only for the purpose intended by
the manufacturer.
Each week drop a small amount of oil on the
beard trimmer blades and turn the trimmer on
for a few seconds. Wipe any excess oil off the
housing.
Fig.5
Fig.6
MN252CSC
BEARD/MUSTACHE TRIMMER
Conair vous remercie d’avoir opté pour la
tondeuse à barbe et moustache. Nous
savons que vous en tirerez des années de
service fiable.
Modèle MN252CSC
®
TAILLE DE LA MOUSTACHE
1. Une moustache propre et humide
donnera de meilleurs résultats.
2. Peignez la moustache dans le sens de la
pousse naturelle.
3. Placez le peigne multi-position sur la lame
de la tondeuse et enclenchez-le. Il est bon de
débuter avec le peigne réglé à la position
longue. (Vous pouvez toujours repasser sur
la moustache avec un réglage plus court.)
TONDEZ TOUJOURS LA
MOUSTACHE DE HAUT
EN BAS
Une fois la moustache taillée,
enlevez le peigne et, n’utilisant
que la lame, découpez la ligne du
bas de la moustache.
LAME À DÉCOUPER
Cette lame sert au découpage fin des poils faciaux.
Une fois les cheveux coupés, utilisez la lame à
découper pour tailler avec finesse autour des
lèvres ou le long de la mâchoire.
1. Posez la lame à découper sur la tondeuse.
2. Mettez la tondeuse en marche.
3. Pressez le bout de la lame à découper contre la
peau et deelacez-la pour créer le découpage voulu.
4. Une fois le travail terminé, mettez l’interrupteur
de la tondeuse en position d’arrêt.
5. Nettoyez la lame avec la brosse fournie.
6. Remettez la tondeuse sur le socle chargeur
après chaque utilisation.
ENTRETIEN DE LA TONDEUSE
ENTRETIEN DES LAMES
Nettoyage de la tête pour la barbe
Ouvrez la tête en appuyant sur le bouton dans le
bas de la tête (ill. 2). Le couvercle s’ouvre et
vous pouvez nettoyer la lame.
Nettoyage de la tête de rasoir
Pour nettoyer la lame et la grille du rasoir :
1. Appuyez sur la deux boutons de dégage-
ment de la grille (ill. 5). Enlevez la tête du
rasoir (la lame est exposée). Ne poussez pas la
grille car elle est délicate et s’endommage
facilement.
2. Nettoyez la lame et ses alentours avec la
petite brosse fournie (ill. 6). Rincez le cadre
sous l’eau courante.
3. Après le rinçage, laissez le cadre sécher à
l’air libre avant de le refermer. Alignez les
flèches sur la cadre et sur la tête puis
enclenchez le cadre en place.
4. Tenez la lame fermement et guidez-la lente-
ment sur la monture. Pressez fermement
04CN1217 IB-5426
1. Tondeuse à barbe
2. Interrupteur sur le manche
3. Logement des piles
4. Peigne accessoire long
5. Peigne accessoire court
6. Rasoir
7. Lame de découpe
8. Socle chargeur et de rangement
9. Brosse de nettoyage
10. Peigne à moustache
11. Huile de lubrification
GARANTIE LIMITÉE DE DEUX ANS
Conair, à sa discrétion, réparera ou remplacera sans
frais un appareil si, au cours des 24 mois suivant la
date de l’achat, il affiche un vice de matière ou de
fabrication.
Pour obtenir un service au titre de la garnatie, ren-
voyer le produit défectueux au service après-vente le
plus près, accompagné du bon de caisse et de 5,50 $
pour les frais de poste et administratifs.
TOUTE GARANTIE IMPLICITE, OBLIGATION OU
RESPONSABILITÉ, Y COMPRIS MAIS SANS Y ÊTRE
LIMITÉ, LA GARANTIE IMPLICITE DE BONNE VENTE
ET D’APTITUDE À ACCOMPLIR UNE TÂCHE PAR-
TICU-LIÈRE, SERA LIMITÉE À LA DURÉE DE 24 MOIS
DE CETTE GARANTIE LIMITÉE ÉCRITE.
EN AUCUN CAS PEUT-ON TENIR CONAIR RESPON-
SABLE DE QUELQUE DOMMAGE SPÉCIAL, INDIRECT
OU FORTUIT QUE CE SOIT, POUR LE BRIS DE CETTE
GARANTIE OU DE TOUTE AUTRE GARANTIE
EXPRESSE OU IMPLICITE QUE CE SOIT.
Cette garantie vous accorde des droits particuliers et
peut aussi vous accorder d’autres droits qui varient
d’une province à l’autre.
Service après-vente :
Conair Consumer Products Inc.
Service Department
156 Parkshore Drive
Brampton, Ontario L6T 5M1
1-800-472-7606
Visitez notre site Web : www.conaircanada.ca
©2004 CONAIR CONSUMER PRODUCTS INC.
156 Parkshore Drive
Brampton, Ontario L6T 5M1
DÉCOUPE DE LA BARBE
1. Il est toujours préférable de débuter avec
une barbe propre et humide.
2. Peignez la barbe dans le sens de la pousse
naturelle. Amorcez le découpe au niveau de
la mâchoire.
3. Posez la tête pour la barbe. Commencez par
définir la forme sous le menton et travaillez
vers le haut, de part et d’autre du visage en
direction des oreilles. Définissez la ligne
supérieure le long des joues, des favoris et
jusqu’à la ligne des cheveux.
TAILLE DE LA BARBE
Il y a 2 peignes à positions multiples pour la
taille de la barbe. Un pour les barbes courtes,
l’autre pour les barbes longues.
1. Pour utiliser le peigne, glissez-le sur la lame
de la tondeuse et enclenchez-le. Au début,
avant que vous soyez habitué aux ajuste-
ments, utilisez le
réglage et le peigne
longs. (Vous pouvez
toujours repasser sur
la barbe pour la tailler
plus courte.)
2. Coupez la barbe en mouvements doux et uni-
formes. Commencez aux
favoris et travaillez en direction
du menton. (Ne tentez jamais
de couper dans le sens con-
traire de la pousse naturelle
sinon les poils seront coupés
trop courts.
3. Si vous voulez une coupe de plus près, vous
pouvez ajuster le peigne en conséquence et
repasser sur la barbe jusqu’à l’atteinte de la
longueur voulue.
Tête pivotant sur 3 positions
jusqu’à ce que la lame s’enclenche.
Mise en garde : Faites attention de ne pas per-
dre le petit ressort sous la lame.
Comme les lames de la tondeuse sont des arti-
cles de précision prévus pour un usage particuli-
er, elles doivent toujours être maniées avec soin.
Après chaque usage,
utilisez la brosse fournie
pour nettoyer les poils sur les lames. Rangez
ensuite la tondeuse sur le socle jusqu’à l’utili-
sation suivante. Pour assurer une longue
durée utile, n’utilisez la tondeuse que pour
l’usage prévu.
Chaque semaine, huilez légèrement les lames
de la tondeuse et laissez la fonctionner
quelques secondes. Essuyez l’excédent
d’huile sur le cadre.
Ill. 2
Ill. 5
Ill. 6
TONDEUSE À BARBE/MOUSTACHE
MN252CSC
Model MN252CSC
PRESSER
PRESSER
PRESSER
OUVRIR
ENCLENCHER
FERMER
Fig.2
1.
2.
3.
4.
5.
6.
8.
9.
11.
10.
7.
1.
2.
3.
4.
5.
6.
8.
9.
11.
10.
7.
1 / 1

Conair MN252CSC Manuel utilisateur

Catégorie
Tondeuses à barbe
Taper
Manuel utilisateur

dans d''autres langues