Applica BDCH11 Series Manuel utilisateur

Catégorie
Chauffe-eau
Taper
Manuel utilisateur

Ce manuel convient également à

IMPORTANT:
During the first few minutes of initial use, you may notice a slight
odor. This is normal and will quickly disappear.
This heater is intended for use on a flat, stable surface, such as a
floor, tabletop, shelf, or desk in a location where the airflow grille
openings won’t be obstructed. Keep all combustible materials such
as furniture, pillows, bedding, paper, clothes and curtains at least 3
feet (.9 m) away from the heater. Do not use in wet or moist locations,
like bathrooms or laundry areas, or in areas where paint or other
flammable or volatile liquids are used or stored.
CAUTION: Be sure no other appliances are plugged into the same
circuit with this heater/fan. A circuit overload could occur.
1. Be sure the Dial is in the OFF position before plugging the unit in
(A). Plug into an AC outlet. Turn the Room Select Dial to the
appropriate setting using High for large rooms and Low for smaller
area. The POWER indicator will light up.
2. Turn the Thermostat Control toward the highest level (HOT) to start
in order to activate the heater/fan. Once the desired room
temperature is achieved, lower the Thermostat Control back down
until the fan cycles off. The heat will now cycle On/Off to maintain
a comfortable level.
3. To use as a fan without heat, turn the Dial to FAN and the
Thermostat Control toward the highest level (HOT) until the fan
begins to operate. No heating will occur in this mode.
SPECIAL FEATURES
1. This unit is equipped with a Safety Auto-Off, plus a Thermal Fuse
and CAUTION light. If the unit experiences excessive heat, the
Safety Auto-Off will shut the unit off, and the CAUTION light will go
on. If this happens, turn the Dial to Off immediately. Be sure the grille
is not blocked and nothing is restricting airflow. If the CAUTION light
stays on, unplug the unit, let it cool down, and wait 10 minutes
before plugging it back in to operate. Readjust your temperature or
room settings. If the unit fails to operate after 10 minutes, it may
mean the heater has internal damage and that the Thermal Fuse has
been tripped so the heater can no longer operate.
2. The POWER Indicator Light shows that the heater is switched on
and operating. It continues to glow even if the thermostat has
cycled and the heating elements are off. Note that even though this
unit has a Cool-Touch Housing, the front grille will get hot. Be
careful not to touch it.
This appliance is permanently lubricated and will not require additional
lubrication for the life of the unit. It contains no user serviceable parts.
Refer service to qualified service personnel.
1. Always turn the unit OFF, unplug, disconnect the cord from the
outlet, and allow the heater to cool completely before cleaning. To
clean the exterior, use a soft dry cloth or one moistened with a mild
detergent to wipe the outside surfaces. Do not use abrasives or
harsh cleansers. Dry surfaces thoroughly before using the heater.
Or, you can use a vacuum with a dusting brush attachment to clean
away dust.
2. Press the Tab on the Dust Filter at the back of the unit and pull the
Dust Filter straight up to remove it (B). Wash it in soapy water, rinse,
and let it air dry completely before putting it back into the heater.
Snap the filter securely back in place.
CAUTION: DO NOT immerse the heater in water or allow water to drip
into the interior of the heater, as this could create an electric shock
hazard.
3. Store the heater in a dry area. Gather the power cord in loops and
secure it with a twist tie. Don’t let the power cord come in contact
with sharp edges or get compressed by heavy objects. Portable
electric heaters are designed for space heating as a supplementary
heat source. They are not intended be the main source of heat.
CARE AND CLEANING
HOW TO USE
UTILISATION
ENTRETIEN ET NETTOYAGE
POLARIZED PLUG
This appliance has a polarized plug—one blade is wider than the
other. To reduce the risk of electric shock, this plug will fit into a
polarized outlet only one way. If the plug does not fit fully into the
outlet, reverse it. If it still does not fit, contact an electrician. Do
not attempt to defeat this safety feature by modifying the plug in
any way.
LINE CORD SAFETY TIPS
1. Never pull or yank on cord or the appliance.
2. To insert plug, grasp it firmly and guide it into outlet.
3. To disconnect appliance, grasp plug and remove it from outlet.
4. Before each use, inspect the line cord for cuts and/or abrasion
marks. If any are found, this indicates that the appliance should
be serviced and the line cord replaced.
5. Never wrap the cord tightly around the appliance, as this could
place undue stress on the cord where it enters the appliance and
cause it to fray and break.
DO NOT OPERATE APPLIANCE IF THE LINE CORD SHOWS ANY
DAMAGE, OR IF APPLIANCE WORKS INTERMITTENTLY OR STOPS
WORKING ENTIRELY.
SPECIAL ATTENTION:
The use of an extension cord is not recommended. However, if it is
absolutely necessary, be sure that the cord is (1) No. 14 AWG
minimum size and rated no less than 1875 watts; (2) UL Listed;
(3) as short as possible (long cords can overheat, as well as trip
circuit breakers); (4) not used for operating more than one appliance
at a time.
FICHE POLARISÉE
L'appareil est muni d'une fiche polarisée (une lame plus large que
l'autre). Afin de minimiser les risques de secousses électriques, ce
genre de fiche n'entre que d'une façon dans une prise polarisée.
Lorsqu'on ne peut insérer la fiche à fond dans la prise, il faut tenter
de le faire après avoir inversé les lames de côté. Si la fiche n'entre
toujours pas dans la prise, il faut communiquer avec un électricien
certifié. Il ne faut pas neutraliser ce dispositif de sécurité.
CONSEILS DE SÉCURITÉ POUR LE FIL ÉLECTRIQUE
1. Ne jamais tirer sur le fil ou sur l’appareil
2. Pour brancher la fiche : Attraper fermement la fiche et la guider
dans la prise.
3. Pour débrancher l’appareil, attraper la fiche et l’enlever de la
prise.
4. Avant chaque usage, inspecter le fil électrique pour coupures ou
marques d’usure. Si on en trouve cela indique qu’il faut réparer
l’appareil et changer le fil électrique.
5. Ne jamais enrouler le fil trop étroitement autour de l'appareil car
cela pourrait exercer trop de pression sur le fil à l'endroit où il
entre dans l’appareil et pourrait l'effilocher et le faire casser.
NE PAS UTILISER L’APPAREIL SI LE FIL ÉLECTRIQUE EST
ENDOMMAGÉ, SI L’APPAREIL NE FONCTIONNE QUE DE FAÇON
INTERMITTENTE OU S’IL NE FONCTIONNE PLUS DU TOUT.
ATTENTION SPÉCIALE :
Il n’est pas recommandé d’utiliser une rallonge. Si cela s’avère
cependant absolument nécessaire, bien utiliser un cordon (1) No. 14
AWG minimum et avec un nominal d’au moins 1875 watts ; (2) qui est
agréé UL ; (3) qui est aussi court que possible (les fils longs peuvent
surchauffer et faire sauter les plombs) ; (4) qui n’est pas utilisé pour
plus d’un appareil à la fois.
IMPORTANT :
On peut remarquer une légère odeur pendant quelques minutes
quand on utilise l’appareil pour la première fois. C’est un phénomène
normal qui disparaîtra rapidement.
Ce radiateur est conçu pour être utilisé seulement sur une surface
stable et plane telle que le plancher, un dessus de table, une étagère
ou un bureau où le flot d’air dans les ouvertures d’entrée et de sortie
ne sera pas obstrué. Garder tous les matériaux combustibles tels que
meubles, coussins, literie, papiers, vêtements et rideaux à au moins 3
pieds du radiateur. Ne pas utiliser dans des endroits humides tels que
salles de bains et buanderies ou dans des endroits où l’on utilise ou
range de la peinture ou d’autres liquides inflammables ou volatiles.
AVERTISSEMENT: S’assurer qu’aucun autre appareil n’est branché
sur le même circuit que ce radiateur. Une surcharge électrique
pourrait se produire.
1. S’assurer que le Sélecteur est sur ARRÊT avant de brancher
l’appareil dans (A). Brancher dans une prise CA. Mettre la
Sélection de Pièce sur le réglage voulu en utilisant Haut pour
grandes pièces et Bas pour des pièces plus petites. Le témoin de
fonctionnement s’allumera.
2. Tourner la commande du Thermostat vers le plus haut niveau
(CHAUD) au début pour mettre en route le radiateur/ventilateur.
Une fois que la température désirée est atteinte, baisser le
thermostat jusqu’à ce que le ventilateur s’arrête. Le radiateur se
mettra en marche et s’arrêtera pour maintenir un niveau
confortable.
3. Pour utiliser un ventilateur sans chaleur, mettre le Sélecteur sur
VENTILATEUR et la commande de Thermostat au plus haut niveau
(CHAUD) jusqu’à ce que le ventilateur se mette en route. L’appareil
ne chauffera pas dans ce mode.
CARACTÉRISTIQUES SPÉCIALES
1. Cet appareil est équipé d’un Arrêt de sûreté automatique ainsi que
d’un fusible thermique et d’un témoin lumineux
d’AVERTISSEMENT. Si l’appareil chauffe trop, l’Arrêt de sûreté
automatique l’éteindra et le témoin lumineux AVERTISSEMENT
s’allumera. Si cela se produit, mettre immédiatement le Sélecteur
sur Arrêt. Vérifier que la grille n’est pas bloquée et que rien ne
restreint le flot d’air. Si la lumière AVERTISSEMENT demeure
allumée, débrancher l’appareil, le laisser se refroidir et attendre 10
minutes avant de le rebrancher et de l’utiliser à nouveau. Ajuster
la température ou le réglage de la pièce. Si l’appareil ne fonctionne
pas après 10 minutes il est possible que le radiateur soit
endommagé à l’intérieur et que le fusible thermique ait sauté,
empêchant l’appareil de fonctionner.
2. Le Témoin de FONCTIONNEMENT montre que le radiateur est
branché et fonctionne. Il reste allumé même si le thermostat a
éteint les éléments de chauffage. Noter que même si cet appareil
possède un Boîtier Athermane, la grille de devant chauffera.
Attention de ne pas la toucher.
Cet appareil a reçu une lubrification permanente et n’aura pas besoin
d’être lubrifié pendant toute sa vie utile. Il ne contient aucune pièce
réparable par l'utilisateur. Si des réparations sont nécessaires,
consulter une personne qualifiée.
1. Toujours mettre l’appareil sur ARRÊT, débrancher le cordon de la
prise
et le laisser se refroidir complètement avant de le nettoyer. Pour
nettoyer l’extérieur, utiliser un chiffon doux sec ou mouillé avec un
détergent doux pour nettoyer la surface extérieure. Ne pas utiliser
de produits abrasifs ni de produits de nettoyage durs. Bien essuyer
la surface avant d’utiliser le radiateur. On peut aussi utiliser un
aspirateur avec une brosse à épousseter pour enlever la
poussière.
2. Appuyer sur l’onglet du Filtre à Poussière au dos de l’appareil et
tirer le Filtre à Poussière pour l’enlever (B). Laver dans de l’eau
savonneuse, rincer et laisser sécher complètement à l’air avant de
le remettre dans le radiateur. Bien remettre le filtre en place.
AVERTISSEMENT : NE PAS tremper l’appareil dans l’eau et ne pas
laisser couler de l’eau à l’intérieur du radiateur car cela pourrait
créer un danger de secousse électrique.
3. Ranger l’appareil dans un endroit sec. Enrouler le cordon
électrique et l’attacher avec une ligature. Veiller à ce que le cordon
n’entre pas en contact avec des bords aigus et ne soit pas
comprimé par des objets lourds. Les radiateurs électriques
portables sont conçus comme chaufferettes ou comme une source
de chaleur supplémentaire. Ils ne sont pas prévus pour être la
source principale de chaleur.
1. POWER Indicator Light
Témoin de Puissance
2. Thermostat Control
Commande du thermostat
3. Handle (in back)
Poignée (à l’arrière)
4. Fan Setting
Réglage du radiateur
5. Hi/Low Room Select
Sélecteur de Puissance
6. CAUTION Indicator Light
Témoin d’AVERTISSEMENT
7. Cool-Touch Housing
Boîtier athermane
8. Front Grille
Grille de devant
† Dust Filter (in back)
(177774-00)
Filtre à poussière (à l’arrière)
A
B
† Consumer replaceable
Remplaçable par le consommateur
When using electrical appliances, basic precautions should always be
followed to reduce the risk of fire, electric shock and injury to persons,
including the following.
"DO NOT COVER" the unit. This means that the airflow through the inlet
and exhaust openings must never be obstructed.
PLEASE READ ALL INSTRUCTIONS BEFORE USING.
This heater is hot when in use. To avoid burns, do not let bare skin
touch hot surface. Unplug and let heater cool down for at least 5
minutes before moving it.
Do not use the unit in enclosed spaces such as inside cabinets or walls
in order to defrost pipes or prevent pipes from freezing.
Use the handle to move the unit.
To reduce the risk of fire, keep combustible materials, such as
furniture, pillows, bedding, papers, clothes and curtains at least 3 feet
(0.9 m) from the front, sides and rear of the heater.
Do not plug heater into loose-fitting or worn out electrical outlets.
Extreme caution is necessary when any heater is used by or near
children or invalids, and whenever the heater is left operating. Avoid
leaving an operating heater unattended.
Always unplug from electrical outlet whenever heater is not in use.
Never pull or yank on the cord or the appliance. To disconnect heater,
turn control to OFF, grasp plug and remove it from outlet.
Do not operate any appliance with a damaged cord or plug or after the
appliance malfunctions or is dropped or damaged in any manner.
Return the appliance to the nearest authorized service facility for
examination, repair, or electrical or mechanical adjustment. Or, call the
appropriate toll-free number listed on the cover of this manual.
Never wrap the cord tightly around the appliance, as this could place
undue stress on the cord where it enters the appliance and cause it to
fray and break. DO NOT OPERATE APPLIANCE IF THE LINE CORD
SHOWS ANY DAMAGE, OR IF APPLIANCE WORKS INTERMITTENTLY
OR STOPS WORKING ENTIRELY. If the supply cord is damaged, it must
be replaced by the manufacturer or its service agent or similarly
qualified person in order to avoid a hazard.
This heater is not intended for use in bathrooms, laundry areas and
similar indoor locations. Never locate heater where it may come in
contact with water, such as near a bathtub or sink. If the heater does
become wet, unplug it from the wall receptacle before touching it, as a
wet heater may create an electrical shock hazard even if the heater is
turned off.
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
Quand on utilise des appareils électriques il convient de toujours prendre
certaines précautions élémentaires pour réduire le risque de sinistre, de
secousse électrique et de blessures, parmi lesquelles :
‘NE PAS RECOUVRIR" le radiateur. Cela signifie que le flot d’air dans les
ouvertures d’entrée et de sortie ne doit jamais être entravé.
LIRE TOUTES LES INSTRUCTIONS AVANT D'UTILISER.
Ce radiateur devient chaud pendant utilisation. Pour éviter de se brûler,
ne pas toucher la surface avec la peau nue. Débrancher et laisser
refroidir pendant au moins 5 minutes avant de déplacer.
Ne pas utiliser l’appareil dans un espace fermé comme à l’intérieur d’un
placard ou de murs pour dégeler les tuyaux ou pour empêcher les
tuyaux de geler.
Utiliser la poignée pour déplacer l’appareil.
Pour réduire le risque d’incendie, ne pas mettre de matériaux
combustibles comme meubles, oreillers, literie, papiers, vêtements et
rideaux à moins de 3 pieds (0,9 m) du devant, des côtés et de l’arrière du
radiateur.
Ne pas brancher le radiateur dans des prises électriques usées ou
lâches.
Il faut être extrêmement prudent quand le radiateur est utilisé par ou
près d’enfants ou d’invalides et quand on laisse le radiateur en marche.
Éviter de laisser le radiateur en marche sans surveillance.
Toujours débrancher de la prise électrique quand on n’utilise pas
l’appareil. Ne jamais tirer sur le cordon ou sur l’appareil. Pour
débrancher l’appareil, mettre la commande sur ARRÊT puis attraper la
fiche et l’enlever de la prise.
Ne pas utiliser cet appareil si la fiche ou le fil sont endommagés, s'il ne
fonctionne pas correctement, si on l'a laissé tomber ou s'il a été
endommagé de quelque manière que ce soit. Apporter l'appareil au
service de réparations agréé le plus proche pour le faire examiner,
réparer ou lui faire recevoir un réglage mécanique ou électrique. On
peut aussi appeler le numéro sans frais approprié indiqué sur la
couverture de ce manuel.
Ne jamais enrouler étroitement le fil autour de l'appareil car cela
pourrait causer de la tension sur le fil à sa jointure avec l'appareil et
l'effilocher ou le couper. NE PAS UTILISER CET APPAREIL SI LE FIL EST
ENDOMMAGÉ OU SI L’APPAREIL FONCTIONNE DE FAÇON
INTERMITTENTE OU CESSE COMPLÈTEMENT DE FONCTIONNER. Si le
cordon est endommagé, il doit être remplacé par le fabricant ou un de
ses agents ou une personne ainsi qualifiée pour éviter un accident.
Ce radiateur n’est pas conçu pour être utilisé dans les salles de bains,
les buanderies et autres emplacements d’intérieur similaires. Ne jamais
placer le radiateur là où il peut entrer en contact avec de l’eau,tel que
près d’une baignoire ou d’un lavabo. Si le radiateur est mouillé, il faut le
Do not use outdoors.
To avoid overheating of the cord, do not cover any part of the cord
with carpet, throw rugs, runners, newspapers, magazines, furniture,
etc. Arrange cord away from trafficked areas, so it will not be tripped
over or stepped on.
Do not insert or allow foreign objects to enter any ventilation
or exhaust opening, as this may cause an electrical shock, fire or
damage to the heater.
To prevent a possible fire, do not block air intakes or exhaust in any
manner. Do not use on soft surfaces (such as a bed) where openings
may be blocked or heater can fall over.
A heater has hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint or other volatile or flammable liquids are
used or stored.
Avoid the use of an extension cord because the extension cord may
overheat and cause a risk of fire. However, if an extension cord must
be used, it must be a minimum size of 14 AWG and rated not less than
1875 watts. Use only an extension cord that is UL listed.
To prevent electrical overload and blown fuses, be sure that no other
appliances are plugged into the same outlet (receptacle) or into
another outlet wired into the same circuit.
Do not place any objects in front of heater.
Do not place the heater near a bed, because objects such as pillows
or blankets can fall off the bed and be ignited by the heater.
Do not use this heater as an integral part of any life support or
equipment protection system, where a functional failure or
misapplication of the heater could jeopardize the people or things
being protected.
Avoid using heater/fan while sleeping.
Use heater only as described in this manual. Any other use is not
recommended by the manufacturer and may cause fire, electric shock
or injury to persons.
This heater includes a visual Caution light to warn that parts of the
heater are getting excessively hot. If the Caution light begins to glow,
immediately turn the heater off and inspect for any objects on or
adjacent to the heater that may cause high temperatures. Do not
operate the heater with the caution light glowing.
This appliance is intended for household use only, not for commercial
or industrial use. Use for anything other than intended will void the
warranty.
débrancher de la prise murale avant de le toucher. Un radiateur humide
peut créer une secousse électrique même s’il est éteint.
Ne pas utiliser à l’extérieur.
Pour éviter de faire surchauffer le fil, ne pas le couvrir, même en partie,
de tapis, passages, journaux, magazines, meubles, etc. Mettre le fil loin
des zones passantes pour qu’on ne lui marche pas dessus et pour qu’il
ne fasse pas tomber.
Ne pas mettre ou laisser pénétrer des objets dans les ouvertures de
ventilation ou de sortie car ils peuvent causer une secousse électrique
ou un sinistre et peuvent endommager le radiateur.
Pour éviter tout risque d’incendie ne pas bloquer les entrées ou sorties
d’air de quelque façon que ce soit. Ne pas utiliser sur une surface molle
(comme un lit) où les ouvertures peuvent être bloquées et où le
radiateur peut se renverser.
Un radiateur contient des pièces chaudes faisant des étincelles à
l’intérieur. Ne pas employer dans des endroits où l’on utilise ou range
de l’essence, de la peinture ou d’autres liquides inflammables ou
volatiles.
Éviter d’utiliser une rallonge qui peut surchauffer et causer un incendie.
S’il faut cependant utiliser une rallonge, elle doit être au minimum de 14
AWG et avoir un nominal d’au moins 1875 watts. N’utiliser que des
rallonges agrées UL.
Pour éviter une surcharge électrique et de faire sauter les plombs,
s’assurer qu’aucun autre appareil n’est branché dans la même prise
(réceptacle) ou dans une autre prise branchée sur le même circuit.
Ne rien placer devant le radiateur.
Ne pas placer le radiateur près d’un lit parce que des objets comme
oreillers et couvertures peuvent tomber du lit et prendre feu.
Ne pas utiliser ce radiateur en tant que partie intégrante d’un
équipement de vie ou d’un système de protection de matériel quand une
défaillance ou une mauvaise utilisation du radiateur pourrait mettre en
danger les individus ou objets protégés.
Éviter d’utiliser le radiateur quand on dort.
N’utiliser ce radiateur que de la façon décrite dans ce manuel. Toute
autre utilisation n’est pas recommandée par le fabricant et peut causer
un sinistre, une secousse électrique ou des blessures.
Ce radiateur contient un témoin lumineux d’Avertissement indiquant
que des parties du radiateur sont devenues excessivement chaudes. Si
la lumière d’Avertissement s’allume, éteindre immédiatement le
radiateur et vérifier s’il y a des objets sur le radiateur ou près de lui qui
peuvent causer des températures élevées. Ne pas utiliser le radiateur
quand la lumière d’Avertissement est allumée.
L’appareil est conçu UNIQUEMENT pour une utilisation domestique et
non industrielle ou commerciale. Toute autre utilisation en annule
la garantie.
Heat Pro
Ceramic Heaters (English)
Radiateurs céramique (Français)
READ AND SAVE THIS USE AND CARE BOOK
CONSERVER CE GUIDE D’ENTRETIEN ET D’UTILISATION
Série BDCH11 Series
Accessories/Parts (USA/Canada) 1-800-738-0245
Accessoires/Pièces
(É.-U./Canada)
?
U.S.A./Canada 1-800-231-9786
http://www.blackanddecker.com
1500 W 120V 60 Hz
*
is a trademark of The Black & Decker Corporation, Towson, Maryland, USA
*Marca registrada de
The Black & Decker Corporation
, Towson, Maryland, E.U.
*Marque de commerce déposée de la société
The Black & Decker Corporation
, Towson, Maryland, É.-U.
Copyright © 2002 Applica Consumer Products, Inc.
Pub. No.178275-00-RV00
Product made in People’s Republic of China
Printed in People’s Republic of China
Produit fabriqué en République populaire de Chine
Imprimé en République populaire de Chine
Product may vary slightly
from what is illustrated.
Le produit peut différer légèrement
de celui illustré.
FULL ONE-YEAR WARRANTY
(Applies only in U.S. and Canada)
NEED HELP?
BESOIN D’AIDE?
GARANTIE COMPLÈTE DE UN AN
(Valable aux É.-U. au Canada seulement)
For service, repair, or any questions regarding your appliance, call the
appropriate "800" number on the cover of this book. Do NOT return the
product to the place of purchase. Do NOT mail the product back to the
manufacturer nor bring it to a service center. You may also want to
consult the website listed on the cover of this manual.
NOTE: If the power supply cord is damaged, it must be replaced by the
manufacturer or its service agent or a similarly qualified person in order
to avoid a hazard.
Pour communiquer avec les services d’entretien ou de réparation, ou
pour adresser toute question relative au produit, composer le numéro
sans frais approprié indiqué sur la page couverture. NE PAS retourner le
produit où il a été acheté. NE PAS poster le produit au fabricant ni le
porter dans un centre de service. On peut également consulter le site
web indiqué sur la page couverture.
NOTE : Lorsque le cordon d'alimentation est endommagé, il faut en
confier la réparation au fabricant, à son agent de service autorisé ou une
personne qualifiée afin d'éviter tout risque.
Applica warrants this product against any defects that are due to faulty
material or workmanship for a one-year period after the original date of
consumer purchase. This warranty does not include damage to the
product resulting from accident, misuse, or repairs performed by
unauthorized personnel. If the product should become defective within
the warranty period, or you have questions regarding warranty or
service, call Consumer Assistance and Information toll free at:
1-800-231-9786.
This warranty gives you specific legal rights and you may also have other
rights which vary from state to state or province to province.
Applica garantit le produit pour un an à compter de la date d'achat,
contre tout vice de matière ou de fabrication. La garantie ne couvre pas
les dommages causés par un accident, une mauvaise utilisation ou des
réparations effectuées par des personnes non autorisées. Advenant le
fonctionnement irrégulier du produit dans les délais prescrits, ou pour
toute question relative à la garantie ou au service, communiquer sans
frais avec le service à la clientèle au numéro suivant : 1 800 231-9786.
Les modalités de la présente garantie donnent des droits légaux
spécifiques. L'utilisateur peut également se prévaloir d'autres droits selon
l'état ou la province qu'il habite.
CONSERVER CES MESURES
IMPORTANTES MISES
EN GARDE
1 / 1

Applica BDCH11 Series Manuel utilisateur

Catégorie
Chauffe-eau
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues