Fulgor Milano F6PGR366S2 Guide d'installation

PRO-RANGE 30”- 36” FULL GAS

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

INSTRUCCIONES PARA LA INSTALACIÓN

Dear Customer,

Thank you for purchasing one of our Soﬁa ranges. This range was

conceived, designed and handcrafted in Italy.

Your selection of a Soﬁa range conﬁrms you are among a special group

who share a love and passion for cooking. This unique community shares

in the experience of creating quality dishes; dishes that will satisfy the

palate while bringing the warmth of families and friends together to share

and rejoice. Impress a loved one with your ability to combine ﬂavours and

ingredients or experiment with new foods and different culinary techniques

to create unexpected pleasures.

EN

1

TABLE OF CONTENTS PAGE

1 - Special Warnings 2

Before Starting Installation 2

Mobile Home Installation 2

Recreational Park Trailers 2

2 - Product Dimensions and Cutout Requirements 3

Anti-Tip Bracket Installation 5

3 - Installation Information 6

4 - Installation Instructions 7

5 - Gas Requirement 9

Pressure Testing 10

Pressure Test Method 10

Gas Connection 11

Conversion for LP or NG Gas 12

Converting Appliance for Use with LP Gas 12

Replace Injectors (two ring ﬂame burner) 12

Replace injector on (oven lower burner) 13

6 - Conversion for LP or NG Gas 14

Converting Appliances for Use with NG Gas 15

Pressure regulator conversion 15

Injectors Position

16

Low Flame Adjustment 18

Adjustment for Burners with one or two ﬂame

rings: 18

Electric Gas Ignition 19

The Burner Flames 19

7 - Electrical Requirements 20

General Information 20

Electrical Connection 20

IMPORTANT: Save these instructions for the local electrical

inspector use.

INSTALLER: Please leave this manual with owner for future

reference.

OWNER: Please keep this manual for future reference.

GLOSSARY OF TERMS: NG - Natural Gas

LP - Liquid Propane

Pay attention to these symbols present in this manual:

DANGER

You can be killed or seriously injured if you don’t

IMMEDIATELY follow instructions.

WARNING

This is the safety alert symbol. This symbol alerts you to

potential hazards that can kill or hurt you and others. You

can be killed or seriously injured if you don’t follow these

instructions.

READ AND SAVE THESE INSTRUCTIONS.

To installer:

Leave these instructions with the appliance.

To customer:

Retain these instructions for future reference.

WARNING

If the information in this manual is not followed exactly, a ﬁre

or explosion may resulting in product and property damage

and / or personal injury or death.

Do not store or use gasoline or other ﬂammable vapours and

liquids in the vicinity of this or any other appliance.

EN

2

Proper installation is your responsibility. Have a qualiﬁed

technician install this range.

IMPORTANT

- Observe all governing codes and ordinances.

- Write down the model and serial numbers before installing

the range. Both numbers are on the serial rating plate refer

to the illustration below.

LOCATION OF RATING PLATE

Before Starting Installation

• Check location where range will be installed. The location

should be away from strong drafty areas, such as windows,

doors and strong heating vents or fans.

• Electrical grounding is required. See “Electrical

Requirements”

• Assure that electrical installation is adequate and in

conformance with National Electrical Code, ANSI/

NFPA 70 - latest edition**, or Canadian Electrical Code,

part 1 C22.1 (latest edition)*** and all local codes and

ordinances.

• Assure that gas connection conforms with local codes and

ordinances. In the absence of local codes, installations

must conform with American National Standard, National

Fuel Gas Code ANSI Z223/NFPA 54 - latest edition**

Canadian CAN/ CGA_B 149.1 or CAN/CGA-149.2

latest edition**

Copies of the standards listed may be obtained from:

** National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

*** CSA International 8501 East Pleasant Valley Rd. Cleveland,

OH 44131-5575

NOTE: This range is manufactured for use with Natural gas

or Propane.

To convert to LP (propane) or NG (natural gas), see

instructions in the gas conversion kit provided in the

literature package. Proper gas supply connection

must be available. See gas supply requirements.

WARNING

Before connecting the appliance to the gas supply line,

ensure that its gas setting is appropriate.

The type of gas adjusted and shipped from the factory is

indicated on the rating plate.

Mobile Home Installation

The installation of this appliances must conform to the

Manufactured Home Construction and Safety Standards, Title

24 CFR, Part 3280 (formerly the Federal Standard for Mobile

Home Construction and Safety; Title 24 HUD part 280); or

when such standard is not applicable, the Standard for

Manufactured Home Installations (Manufactured Home Sites,

Communities and Setups), ANSI A225.1 - latest edition, or

with local codes.

In Canada, the installation of this appliances must conform

with the current standards CAN/CSA-Z240 - latest edition, or

with local codes.

Recreational Park Trailers

The installation of this appliances designed for Recreational

Park Trailers must conform with state or other codes or, in the

absence of such codes, with the Standard for Recreational

Park Trailers, ANSI A119.5.

1 - Special Warnings

IMPORTANT INSTRUCTION

Please read all instructions before using this appliance.

EN

3

PRODUCT DIMENSIONS

30” Wide Range Models 36” Wide Range Models

29 3/4” (75.8)

35 3/4” (91.0)

7” (17.9)

1 3/8” (3.5)

3 3/8” (8.5)

TO

27 1/4” ( 69.1)

25 3/4” ( 65.4)

3/8” (1)

47 3/4” (121.4)

27 1/2” (69.7)

29 3/4” (75.6)

Max. 37 1/4” (94.7)

Min. 35 3/8” (89.8)

1" ( 2.5)

3" ( 7.6) [optional]

9" (22.8) [optional]

2 - Product Dimensions and Cutout Requirements

EN

4

2 - Product Dimensions and Cutout Requirements

CUTOUT REQUIREMENTS

ELECTRICGAS

B B

*Suggested location

of utilities

2” (5.1) max. protusion from

wall for gas or electrical supply

3” (7.6)

4” 3/4 (12.3)

A

Min. 18” (45.7)

Min. 30” (76.2)

To bottom of

ventilation hood

Min. 48” (122)

Minimum

to Combustibles

Min. 18” (45.7)

Max.

13” (33)

Min. 6”

(15.2)

Min. 6”

(15.2)

C

The surface of the entire back wall above the range and below the hood must be covered with a noncombustible material.

*Consult local code for exact location requirements.

OPENING WIDTH A & C B

Range 30” 30" (76.2) 6” (15.2)

Range 36” 36" (91.4) 7” (17.8)

Note: Clearances from non-combustible materials are not

part of the ANSI Z21.1 scope and not certied.

Clearances to non-combustible materials must

conform with local codes or, in the absence of local

codes, with the National Fuel Gas Code, ANSI

Z223.1/NFPA 54.

Minimum clearances:

Above cooking surface (above 36” [91.4 cm])

• Sides - 6” (15.2 cm)

• Within 6” (15.2 cm) side clearance, wall cabinets no

deeper than 13” (33.0 cm) must be minimum 18” (45.7

cm) above cooking surface

• Wall cabinets directly above product must be a minimum

of 48” (122 cm) above cooking surface.

• Rear - 0” with 9 ” backguard; 0” with non-combustible

rear wall.

Below cooking surface (36” [91.4 cm] and below)

• Install with zero clearance between adjacent combustible

construction below the cooking surface and the back

and sides of the appliance.

ADDITIONAL CLEARANCES:

For island installation, maintain 2-½ in. minimum from

cutout to back edge of countertop and 3 in. minimum from

cutout to side edges of countertop (see top view).

For installation in a stepped island, 12” (30.5 cm) minimum

clearance is required from the back or sides of the rangetop

to a combustible riser. The island installation is not part of

the ANSI Z21.1 scope and not certiﬁed.

FLUSH ISLAND INSTALLATION

BACK

min 3” (7.6) min 3” (7.6)

min 2 1/2” (6.3)

EN

5

2 - Product Dimensions and Cutout Requirements

Before moving the range, protect any ﬁnished ﬂooring and

secure oven door(s) closed to prevent damage.

Vent hood Combinations:

It is recommended that these ranges be installed in conjunction

with a suitable overhead vent hood.

Install a hood with at least 450 CFM.

Due to the high heat capacity of this unit, particular attention

should be paid to the hood and ductwork installation to assure

it meets local building codes.

WARNING

Air curtain or other overhead hoods, which operate by

blowing a downward air ﬂow on to a range, shall not be used

in conjunction with ranges with gas cooktop other than when

the hood and range have been designed, tested and certiﬁed

by an independent test laboratory for use in combination with

each other.

Clearances to horizontal surfaces above the range, measured

to the cooking surface are below. Failure to comply may

result in ﬁre hazard.

• Installations without a hood require 48” (122) minimum

to combustibles.

• A custom hood installation with exposed horizontal

combustible surfaces must have an Auto-On feature.

• For other installations with a hood, refer to the hood

installation instructions for speciﬁc hood clearances.

CAUTION

These ranges weigh up to 400 pounds. Some disassembly

will reduce the weight considerably. Due to the weight and

size of the range and to reduce the risk of personal injury or

damage to the product:

TWO PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.

Anti-Tip Bracket Installation

WARNING

Tip Over Hazard

A child or adult can tip the range and be killed.

Ensure the anti-tip bracket is engaged when the range is

moved.

Do not operate range without anti-tip bracket installed and

engaged.

Failure to follow these instructions can result in death or serious

burns to children and adults.

WARNING

To verify the anti-tip bracket is installed and engaged:

• Slide range forward.

• Look for the anti-tip bracket securely attached to ﬂoor or wall.

• Slide range back so rear range foot is under anti-tip bracket.

• See installation instructions for details.

Range Foot

Anti-Tip Bracket

ANTI-TIP BRACKET INSTALLATION

ANTI-TIP

BRACKET

FLUSH

CABINET

SIDEWALL

BACKWALL

WALL

ANCHOR

For Concrete or Cement Construction:

You must use appropriate fastening hardware (not

provided).

Secure the bracket to the wall and/or ﬂoor with at least 4

wood screws (provided).

The anti-tip bracket should be inserted into the opening on

the anti-tip brace on the range.

EN

6

3 - Installation Information

WARNING

• Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

• Cut Hazard

Beware of sharp edges. Use the polystyrene ends when

carrying the product. Failure to use caution could result in

minor injury or cuts.

Do not obstruct the ﬂow of combustion air at the oven vent

nor around the base or beneath the lower front panel of the

range. Avoid touching the vent openings or nearby surfaces

as they may become hot while the oven is in operation. This

range requires fresh air for proper burner combustion.

NEVER cover any slots, holes or passages in the oven or

cover an entire rack with aluminum foil. Doing so blocks

air ﬂow through the oven and may cause carbon monoxide

poisoning. Aluminum foil linings may also trap heat, causing

a ﬁre hazard.

CHOOSING RANGE LOCATION

Carefully select the location where the range will be placed.

The range should be located for convenient use in the kitchen,

but away from strong drafts.

Strong drafts may be caused by open doors or windows, or by

heating and/or air conditioning vents or fans.

IMPORTANT NOTE

When installing against a combustible surface, a minimum

riser is required for a the range, Follow all minimum

clearances to combustible surfaces shown in the illustration

on the previous pages.

Before moving the range, protect any ﬁnished ﬂooring and

secure oven door(s) closed to prevent damage.

Do not lift or carry the range door by the door handle.

To eliminate the risk of burns or ﬁre by reaching over heated

surface units, cabinet storage space located above the surface

units should be avoided. If cabinet storage is to be provided,

the risk can be reduced by installing a range hood that projects

horizontally a minimum of inches beyond the bottom of the

cabinets.

All openings in the wall or ﬂoor where the range is to be

installed must be sealed.

TOOLS WILL YOU NEED

Remove packaging materials and literature package from the

cooktop before beginning installation.

Remove Installation Instructions from the literature pack and

read them carefully before you begin

MATERIALS PROVIDED

Anti-tip bracket

brace abd screws

Appliance

pressure

regulator

Flare union

adaptor

Gasket

MATERIALS REQUIRED (not provided)

Shut-Off Valve

Pipe Fittings

5-foot maximum length, 5/8” O.D. CSA-approved flexible

metal gas supply (3-foot maximum length in Massachusetts only)

NOTE: Purchase new flexible line; do not use previously used

flexible gas line.

Joint Sealant

EN

7

4 - Installation Instructions

STEP 1

Cut the banding and remove the appliance from the pallet by a

hand-truck inserting the blade under the foam base.

CAUTION

Stand clear. The ends of the cut banding may snap toward you.

STEP 2

Remove Installation Instructions from the top of range and read

them carefully before you begin.

STEP 3

Move the range indoors before installing the legs, position the

appliance near its ﬁnal location as the legs are not suitable for

moving the appliance over long distances.

Legs are packed in the cardboard top pack.

CAUTION

Doors and passageways leading to the installation location

require at least 31” opening. If the opening is less than 31”,

the oven door(s) and control knobs must be removed.

(see Use & Care manual for oven door removal instructions).

Note: the legs with collar must be mounted on the back of range

to engage the anti tip device.

STEP 4

With the foam base still in place, tilt the range laterally and

screw in the ﬁrst pair of legs.

EN

8

STEP 5

Pull out the hand-truck, tilt the range laterally and insert the

second pair of legs. Remove the base

STEP 6

Install the backsplash (if provided) by the three screws on the

back and the toe kick

3”9”

STEP 7

After the electrical and gas connections (see both paragraphs

for instructions) measure the four corners in cutout area to verify

if ﬂooring is level. Adjust the leveling legs to the desired height

and ensure range is level. Turn the bottom section of each leg

counter-clockwise to raise the leg and clock wise to lower it.

Ensure ﬂoor is protected. Slide unit into place making sure to

engage the anti-tip bracket.

STEP 8

Hook tabs on bottom of toekick into slots on either side of

the frame and rotate up until clips at top of toekick engage

securely.

NOTE: Be sure the toekick snaps securely.

4 - Installation Instructions

EN

9

5 - Gas Requirement

QUALIFIED SERVICE MAN OR GAS APPLIANCE INSTALLER

MUST MAKE THE GAS SUPPLY CONNECTION.

Leak testing of the appliance shall be conducted by the installer

according to the instructions given.

WARNING

If the line pressure supplying the appliance pressure regulator

exceeds 14 inches W.C. (any gas), an external regulator

must be installed in the gas line ahead of the appliance

regulator to reduce the pressure to no more than 14 inches

W.C. Failure to do this can result in malfunction and damage

to the appliance.

Important Notes for Gas Connection

The appliance and its individual gas shutoff valve must be

disconnected from the gas supply piping system during any

pressure testing of that system at test pressures in excess of 1/2

psi (3.5 kPa).

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 psi (3.5 kPa).

GAS SHUT OFF VALVE

OPEN POSITION

TO APP

L

I

A

N

C

E

G

AS

SUPPL

Y

All supply piping, except as noted, should use common

National Pipe Thread (N.P.T.). For all pipe connections use an

approved pipe joint compound resistant to the action of LP gas.

This appliance is designed for use with NG gas or LP gas.

The gas pressure regulator is supplied with this appliance.

It must be installed in the gas ahead of the manifold entrance.

It is pre-set for use with natural gas. To use it with different

gas it must be converted, as described in the Gas Conversion

paragraph.

If at any time the appliance is to be used with a different type

of gas, all the conversion adjustments must be made by a

qualiﬁed technician before attempting to operate the range

with that gas.

The gas should be supplied to the appliance’s pressure regulator

at line pressure between 6 and 14 inches of water column for

NG, and between 11 and 14 inches of water column for LP.

GAS REQUIREMENTS

NATURAL GAS WC

Manifold Pressure 5" (12.5 mb)

Min Line Pressure 6" (15 mb)

Max Line Pressure 14" (34.9 mb), .5 psi (3.5 kPa)

LP GAS WC

Manifold Pressure 10” (25 mb)

Min Line Pressure 11” (27.4 mb)

Max Line Pressure 14” (34.9 mb), .5 psi (3.5 kPa)

LOCATION OF GAS RATING PLATE

EN

10

5 - Gas Requirement

IMPORTANT

NEVER REUSE OLD CONNECTORS WHEN INSTALLING THIS

RANGE.

To reduce the likelihood of gas leaks, apply teﬂon tape or a

thread compound approved for use with LP or Natural gases

to all threaded connections.

Apply a non-corrosive leak detection ﬂuid to all joints and

ﬁttings in the gas connection between the supply line shut-off

valve and the cooktop inlet.

Check for leaks!

Bubbles appearing around ﬁttings and connections will

indicate a leak. If a leak appears, turn off supply line gas

shut-off valve, tighten connections, turn on the supply line gas

shutoff valve, and retest for leaks. Never test for gas leaks

with an open ﬂame.

NEVER TIGHTEN TO MORE THAN 35 ft lbs OF TORQUE

CAUTION

Do not attempt to attach the ﬂexible connector directly to an

external pipe thread.

Connection requires ﬂare union adapters.

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas valve.

2. Flexible gas connector must not be longer than 36 inch.

3. Not approved for installation in a bedroom or a bathroom

unless unit is direct vent.

Pressure Testing

The appliance must be isolated from the gas supply piping

system by closing its individual manual shut-off valve during

any pressure testing of the gas supply piping system at test

pressures equal to or less than 1/2 PSIG (3.5 kPa).

This appliance, as well as its individual shut-off valve, must be

disconnected from the gas supply piping system during any

pressure testing of the system at test pressures in excess of 1/2

PSIG (3.5 kPa).

When checking appliance regulator function, make certain

pressure of natural gas supply is between 6 and 14 inches of

water column or, if converted for LP gas, between 11 and 14

inches.

THE PRESSURE TESTING SHOULD BE PERFORMED BY

MEANS OF THE INJECTOR THREAD ZONE

EXPLODED VIEW OF BURNER

1

2

A

Pressure Test Method

• Remove grate and burner cap (1).

• Remove aluminum gas spreader (2).

• Temporarily remove the injectors (A).

• Connect the pressure Test instrument into injector holder

thread zone (M6x0,75).

• Check if the cooktop has the correct pressure.

• Fix the injector removed for testing and replace the parts in

the right position.

EN

11

6 - Gas Requirement

Gas Connection

• Thread the appliances pressure regulator with 1/2” male

end connection both supplied with this appliance.

• Join the pressure regulator to the entrance threads of the

Gas Manifold with gasket supplied with this appliance.

The regulator is marked with a directional arrow indicating

correct direction of gas ﬂow. Ensure the appliance regulator

is installed with the arrow pointing toward the gas manifold

entrance.

• Connect a manual shut-off valve to the gas supply in an

accessible location for turning on or shutting off gas to the

appliance.

• Install a coupling between the regulator and the shutoff valve

to complete the connection.

• Assure all pipe joint connections are gas tight.

• Check alignment of valves after connecting the cooktop to the

gas supply to be sure the manifold pipe has not been moved.

FOR ALTERNATIVE PIPING METHODS TO CONNECT THE

APPLIANCE TO THE GAS SUPPLY, A TRAINED SERVICE

TECHNICIAN OR GAS APPLIANCE INSTALLER MUST MAKE THE

GAS SUPPLY CONNECTION. Leak testing of the appliance shall be

conducted by the Installer according to the Instructions given.

Unless prohibited by local codes or ordinances, a new A.G.A.

- Certiﬁed, ﬂexible metal appliance connector may be used to

connect this appliance to its gas supply.

The connector must have an internal diameter not less than

nominal 1/2” NPT pipe and be no more than 5 feet in length.

A 1/2” NPT x 1/2” ﬂare union adapter is required at each end

of the ﬂexible connector.

If a ﬂexible connector is used assure that both the appliance

pressure regulator and manual shut-off valve are joined solidly to

other permanent hard piping (either gas supply or the appliance

manifold) so as to be physically stationary.

CAUTION

Do not attempt to attach the ﬂexible connector directly to an

external pipe thread.

Connection requires ﬂare union adapters.

For Massachusetts Installations:

1. Shut-off valve must be a “T” handle gas valve.

2. Flexible gas connector must not be longer than 36 inches.

3. Not approved for installation in a bedroom or a bathroom

unless unit is direct vent.

GAS CONNECTION

GASKET

FLARE UNION ADAPTOR

APPLIANCE PRESSURE REGULATOR

MANIFOLD SHUTOFF VALVES

FLEXIBLE APPLIANCE CONNECTOR

(5 FT.) MAX, (1.52 m) MAX

APPLIANCE PRESSURE REGULATOR

GASKET

FLARE UNION ADAPTOR

FLEXIBLE APPLIANCE CONNECTOR

(5 FT.) MAX, (1.52 m) MAX

MANIFOLD SHUTOFF VALVES

EN

12

6 - Conversion for LP or NG Gas

Converting Appliance for Use with LP Gas

WARNING

Conversion is to be performed by an AUTHORIZED

SERVICER (or other qualiﬁed agency) in accordance with the

manufacturer’s instructions and all codes and requirements of

the authority having jurisdiction. Failure to follow instructions

could result in serious injury or property damage.

The qualiﬁed agency performing this work assumes

responsibility for this conversion.

CAUTION

Before proceeding with the conversion, shut off the gas supply

to the appliance prior to disconnecting the electrical power

If this appliance is to converted for use with gas LP (propane

or butane), each of the following modiﬁcations must be

performed:

Gas conversion label (aluminium) to be placed on the back of

the appliance, near the data plate, after conversion has been

carried out;

Replace Injectors (two ring ﬂame burner)

1. Remove the grates and burner caps.

2. Remove aluminium gas spreader.

3. Remove the three screws from the simmer gas spreader

(1).

4. Remove the two screws of the injector cover (2).

5. Remove injector (A) by using a 9-32” nut driver counter

clockwise.

6. Remove injector (B) by using a 9-32” box wrench counter

clockwise.

7. Install the injectors supplied with this appliance in the

appropriate burner. The injectors have small numbers

stamped on the side, this number corresponds with the

oriﬁce diameter and its correct burner location (refer to

illustrations in the section: “Injectors Position”).

8. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs).

9. Replace all parts following the reverse order.

10. Save the injectors removed from the appliances for

future use.

EXPLODED VIEW OF BURNER

1

2

B

A

EN

13

6 - Conversion for LP or NG Gas

Replace injector on (oven lower burner)

1. Remove the burner cover plate.

2. Disconnect both heat sensor and the ignition spark plug.

3. Remove the screw securing the oven burner and withdraw

the burner from the support.

4. Remove the nozzle by turning 9-32” nut driver counter

clockwise.

5. Install the injectors supplied with this appliances in the

appropriate burner. The injectors have small number

stamped on the side, this number codes the oriﬁce diameter

and its correct burner location (see ﬁgure of the paragraph

“Injectors position”).

6. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs)

7. Replace all parts following the reverse order. Save the

injectors removed from the appliances for future use.

EN

14

Replace injector on (oven grill burner)

1. Remove the door as described in the paragraph “Door

removal”

2. Remove the screws securing the grill burner and withdraw

the burner from the support.

3. Remove the nozzle by turning 9-32” nut driver counter

clockwise.

4. Install the injectors supplied with this appliances in the

appropriate burner. The injectors have small number

stamped on the side, this number codes the oriﬁce diameter

and its correct burner location (see ﬁgure of the paragraph

“Injectors position”).

5. Turn clockwise to tighten (tighten to a torque of 15 to 20

inch-lbs)

6. Replace all parts following the reverse order paying

attention to the correct placement of the burner.

7. Save the injectors removed from the appliances for future

use.

6 - Conversion for LP or NG Gas

EN

15

6 - Conversion for LP or NG Gas

Proceed to Pressure Regulator Conversion noting the LP /

Propane position to complete the conversion.

After replacing the injectors adjust the burner ﬂame (see Low

Flame Adjustment paragraph).

Check the appearance of each burner’s ﬂame at HILO settings,

if the ﬂame appears too large or too small make sure that all

steps were completed correctly.

Converting Appliances for Use with NG Gas

If this appliance should be converted for use with gas NG

(natural gas), each of the following modiﬁcations must be

performed.

1. Convert the pressure regulator to NG position as per the

section “Pressure Regulator Conversion”.

2. Replace all injectors following the step described on the

previous pages, observe the number stamped on the side,

this number corresponds to the oriﬁce diameter and its

correct burner location (refer to the illustrations in section:

“Injectors Position”).

3. Adjust the burner ﬂame (see Low Flame Adjustment section).

Check the appearance of each burner’s ﬂame at HI - LO

settings, if the ﬂame appears too large or too small make sure

that all steps were completed correctly.

Pressure regulator conversion

The appliances is designed for use with NG gas or LP gas. The

gas pressure regulator is supplied. It must be installed in the

gas supply line ahead of the manifold entrance.

It is pre-set for use with the gas as indicated on the appliance

label supplied with the appliance. For use with different gas

the appliance must be converted.

For the pressure regulator conversion follow the instructions

below:

• Disconnect all electrical power, at the main circuit breaker

or fuse box.

• Shut off the gas supply to the cooktop by closing the manual

shut-off valve.

• Adjust the pressure regulator, by following the instruction

(see ﬁgure)

1. Unscrew the regulator cap

2. Unscrew the plastic conversion plug from the cap turn

over and screw back (wide section away from cap for

LP and against cap for NG) see ﬁgures below.

3. Replace the regulator cap ensuring gasket is in place.

PRESSURE REGULATOR CONVERSION

NG

LP

NG POSITION

PLUG

PRESSURE REGULATOR

LP/PROPANE POSITION

GASKET

CAP

Before replacing the regulator cap, check if the position

of plug is suitable for the gas

EN

16

6 - Conversion for LP or NG Gas

INJECTORS POSITION

NG- DUAL FLAME RING 30”

210

175

*MAIN FLAME 180 or

*MAIN FLAME 192

SIMMER 72

MAIN FLAME 180

SIMMER 72

NG- DUAL FLAME RING 36”

*MAIN FLAME 180 or

*MAIN FLAME 192

SIMMER 72

MAIN FLAME 180

SIMMER 72

230

200

* depending on the model

La page charge ...

Fulgor Milano F6PGR366S2 Guide d'installation

Ce manuel convient également à

Fulgor Milano F6PGR366S2 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents