MTD TB250 Le manuel du propriétaire

Marque: MTD

Modèle: TB250

Catégorie: Souffleurs / sécheurs d'air

Taper: Le manuel du propriétaire

Operator’s Manual

2-Cycle Gasoline

Blower

Model TB250B

P/N 769-01169 (4/04)

PRINTED IN USA

SAVE THESE INSTRUCTIONS DO NOT THROW AWAY

INTRODUCTION

Copy the serial number

here:

THANK YOU

Thank you for buying this quality product. This modern

outdoor power tool will provide many hours of useful

service. You will find it to be a great labor-saving device.

This operator’s manual provides you with easy-to-

understand operating instructions. Read the whole

manual and follow all the instructions to keep your new

outdoor power tool in top operating condition.

PRODUCT REFERENCES, ILLUSTRATIONS

AND SPECIFICATIONS

All information, illustrations, and specifications in this

manual are based on the latest product information

available at the time of printing. We reserve the right to

make changes at any time without notice.

Reserved.

SERVICE INFORMATION

Service on this unit both within and after the warranty

period should be performed only by an authorized and

approved service dealer.

For service call 1-800-520-5520 to obtain a list of

authorized service dealers near you. For more details

about your unit, visit our website at www.troybilt.com.

DO NOT RETURN THE UNIT TO THE RETAILER.

PROOF OF PURCHASE WILL BE REQUIRED FOR

WARRANTY SERVICE.

Before beginning, locate the unit’s model plate. It lists

the model and serial numbers of your unit. Refer to the

sample plate below and copy the information for future

reference.

S/N :

ITEM :

MODEL :

Make sure you carefully read and understand this manual

before starting or operating this equipment.

THIS PRODUCT IS COVERED BY ONE OR MORE U.S.

PATENTS. OTHER PATENTS PENDING.

TABLE OF CONTENTS

Service Information . . . . . . . . . . . . . . . . . . . . . . . . .2

Rules for Safe Operation . . . . . . . . . . . . . . . . . . . . .3

Know Your Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Assembly Instructions . . . . . . . . . . . . . . . . . . . . . . .7

Oil and Fuel Information . . . . . . . . . . . . . . . . . . . . . .8

Starting/Stopping Instructions . . . . . . . . . . . . . . . . .9

Operating Instructions . . . . . . . . . . . . . . . . . . . . . .10

Maintenance and Repair Instructions . . . . . . . . . . .11

Cleaning and Storage . . . . . . . . . . . . . . . . . . . . . . .13

Accessories and Replacement Parts . . . . . . . . . . .13

Troubleshooting Chart . . . . . . . . . . . . . . . . . . . . . .14

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Warranty Information . . . . . . . . . . . . . . . . . . . . . . .18

Parts List . . . . . . . . . . . . . . . . . . . .Inside Back Cover

Copy the model and parent

part number here:

SPARK ARRESTOR NOTE

NOTE: For users on U.S. Forest Land and in the

states of California, Maine, Oregon and Washington.

All U.S. Forest Land and the state of California (Public

Resources Codes 4442 and 4443), Oregon and

Washington require, by law that certain internal

combustion engines operated on forest brush and/or

grass-covered areas be equipped with a spark arrestor,

maintained in effective working order, or the engine be

constructed, equipped and maintained for the prevention

of fire. Check with your state or local authorities for

regulations pertaining to these requirements. Failure to

follow these requirements could subject you to liability or

a fine. This unit is factory equipped with a spark

arrestor. If it requires replacement, ask your LOCAL

SERVICE DEALER to install the Spark Arrestor Kit.

CALIFORNIA PROPOSITION 65 WARNING

WARNING

THE ENGINE EXHAUST FROM THIS

PRODUCT CONTAINS CHEMICALS

KNOWN TO THE STATE OF CALIFORNIA

TO CAUSE CANCER, BIRTH DEFECTS

OR OTHER REPRODUCTIVE HARM.

READ ALL INSTRUCTIONS

BEFORE OPERATING

• Read the instructions carefully. Be familiar with the

controls and proper use of the unit.

• Do not operate this unit when tired, ill, or under the

influence of alcohol, drugs, or medication.

• Children and teens under the age of 15 must not use

the unit, except for teens guided by an adult.

• All guards and safety attachments must be installed

properly before operating the unit.

• Inspect the unit before use. Replace damaged parts.

Check for fuel leaks. Make sure all fasteners are in

place and secure. Replace parts that are cracked,

chipped, or damaged in any way. Do not operate the

unit with loose or damaged parts.

• Carefully inspect the area before starting the unit.

Remove all debris and hard or sharp objects such as

glass, wire, etc.

• Clear the area of children, bystanders, and pets. At a

minimum, keep all children, bystanders, and pets

outside a 50 feet (15 m.) radius; there still may be a

risk to bystanders from thrown objects. Bystanders

should be encouraged to wear eye protection. If you

are approached, stop the unit immediately.

SAFETY WARNINGS FOR GAS UNITS

• Store fuel only in containers specifically designed and

approved for the storage of such materials.

• Avoid creating a source of ignition for spilled fuel. Do

not start the engine until fuel vapors dissipate.

• Always stop the engine and allow it to cool before filling

the fuel tank. Never remove the cap of the fuel tank, or

add fuel, when the engine is hot. Never operate the unit

without the fuel cap securely in place. Loosen the fuel

tank cap slowly to relieve any pressure in the tank.

• Mix and add fuel in a clean, well-ventilated outdoor area

where there are no sparks or flames. Slowly remove the

fuel cap only after stopping engine. Do not smoke while

fueling or mixing fuel. Wipe up any spilled fuel from the

unit immediately. Always wipe unit dry before using.

• Move the unit at least 30 feet (9.1 m) from the fueling

source and site before starting the engine. Do not

smoke or allow sparks and open flames near the area

while adding fuel or operating the unit.

RULES FOR SAFE OPERATION

SYMBOL MEANING

The purpose of safety symbols is to attract your

attention to possible dangers. The safety symbols,

and their explanations, deserve your careful attention

and understanding. The safety warnings do not by

themselves eliminate any danger. The instructions or

warnings they give are not substitutes for proper

accident prevention measures.

NOTE: Advises you of information or instructions vital to

the operation or maintenance of the equipment.

SYMBOL MEANING

When using the unit,

you must follow the

safety rules. Please read these instructions

before operating the unit in order to ensure

the safety of the operator and any bystanders.

Please keep these instructions for later use.

WARNING:

• IMPORTANT SAFETY INSTRUCTIONS •

Failure to obey a

safety warning can

result in injury to yourself and others.

Always follow the safety precautions to

reduce the risk of fire, electric shock and

personal injury.

WARNING:

Failure to obey a

safety warning will

result in serious injury to yourself or to

others. Always follow the safety precautions

to reduce the risk of fire, electric shock and

personal injury.

DANGER:

Failure to obey a

safety warning may

result in property damage or personal injury

to yourself or to others. Always follow the

safety precautions to reduce the risk of fire,

electric shock and personal injury.

CAUTION:

Indicates

danger,

warning or caution. Attention is required in

order to avoid serious personal injury. May

be used in conjunction with other symbols

or pictographs.

SAFETY ALERT:

Gasoline is highly

flammable, and its

vapors can explode if ignited. Take the

following precautions:

WARNING:

Read the Operator’s Manual(s) and follow all

warnings and safety instructions.

Failure to do so can result in serious injury to the

operator and/or bystanders.

FOR QUESTIONS, CALL 1-800-520-5520

RULES FOR SAFE OPERATION

WHILE OPERATING

• Never start or run the unit inside a closed room or

building. Breathing exhaust fumes can kill. Operate this

unit only in a well-ventilated outdoor area.

• To reduce the risk of injury associated with thrown

objects, wear safety glasses or goggles that are

marked as meeting ANSI Z87. standards.

• Never run the unit without the the proper equipment

attached. When using this unit, always install the

blower tubes.

• To reduce the risk of hearing loss associated with

sound level(s), always wear ear/hearing protection

when operating this unit.

• Wear heavy, long pants, boots, and gloves. Do not

wear short pants, sandals, or go barefoot.

• To avoid static electricity shock, do not wear rubber

gloves or any other insulated gloves while operating

this unit.

• To reduce the risk of injury associated with objects

being drawn into rotating parts, do not wear loose

clothing, jewelry, scarves, and the like. Secure hair

above shoulder level.

•Wear a face or dust mask if the operation is dusty.

Long sleeve shirts are recommended.

• Use the unit only in daylight or good artificial light.

• Keep outside surfaces free from oil and fuel.

• Avoid accidental starting. Be in the starting position

whenever pulling the starter rope. The operator and

unit must be in a stable position while starting. Refer to

Starting/Stopping Instructions.

• Do not set unit on any surface except a clean, hard

area while engine is running. Debris such as gravel,

sand, dust, grass, etc. could be picked up by the air

intake and thrown out by the discharge opening,

damaging unit, property, or causing serious injury to

bystanders or operator.

• Use the right tool. Only use this tool for the purpose

intended.

• Do not force unit. It will do the job better and with less

likelihood of injury at a rate for which it was designed.

• Do not overreach or use from unstable surfaces such

as ladders, trees, steep slopes, rooftops, etc. Always

keep proper footing and balance.

• Always hold the unit with a firm grip when operating.

• Keep hands, face, and feet at a distance from all moving

parts. Do not touch or try to stop the impeller when it is

rotating. Do not operate without guards in place.

• Do not put any object into openings. Do not use with

any opening blocked; keep free of dirt, debris, and

anything that may reduce the air flow.

• Do not touch the engine or muffler. These parts get

extremely hot from operation. When turned off they

remain hot for a short time.

• Do not operate the engine faster than the speed

needed to do the job. Do not run the engine at high

speed when not in use.

• Always stop the engine when operation is delayed or

when walking from one location to another.

• Stop the engine for maintenance, repair, to install or

remove the blower tubes. The unit must be stopped

and the impeller no longer turning to avoid contact with

the rotating blades.

• Use only original equipment manufacturer replacement

parts when servicing this unit. These parts are available

from your authorized service dealer. Do not use

unauthorized parts, accessories, or attachments for

this unit. Doing so could lead to serious injury to the

user, or damage to the unit, and void your warranty.

• Never use this unit for spreading chemicals, fertilizers or

other substances which may contain toxic materials.

•To reduce fire hazard, replace faulty muffler and spark

arrestor, keep the engine and muffler free from grass,

leaves, excessive grease or carbon build up.

• Never point the blower in the direction of people or

pets, or in the direction of windows. Always direct the

blowing debris away from people, animals, and

windows. Use extra caution when blowing debris near

solid objects such as trees, automobiles, walls, etc.

OTHER SAFETY WARNINGS

• Always disconnect the spark plug before performing

maintenance or accessing movable parts.

• Never store the unit, with fuel in the tank, inside a

building where fumes may reach an open flame (pilot

lights, etc.) or sparks (switches, electrical motors, etc.).

• Allow the engine to cool before storing or transporting.

Be sure to secure the unit while transporting.

• Store the unit in a dry place, either locked up or up

high to prevent unauthorized use or damage. Keep out

of the reach of children.

• Never douse or squirt the unit with water or any other

liquid. Keep handles dry, clean, and free from debris. Clean

after each use, see Cleaning and Storage instructions.

• Keep these instructions. Refer to them often and use

them to instruct other users. If you loan this unit to

others, also loan these instructions to them.

SPECIAL NOTE: Exposure to vibrations through prolonged

use of gasoline powered hand tools could cause blood

vessel or nerve damage in the fingers, hands, and joints of

people prone to circulation disorders or abnormal swelling.

Prolonged use in cold weather has been linked to blood

vessel damage in otherwise healthy people. If symptoms

occur such as numbness, pain, loss of strength, change in

skin color or texture, or loss of feeling in the fingers, hands or

joints, discontinue use of this tool and seek medical

attention. An anti-vibration system does not guarantee

avoidance of these problems. Users who operate power

tools on a regular basis must closely monitor their physical

condition and the condition of this tool.

SAVE THESE INSTRUCTIONS

RULES FOR SAFE OPERATION

SYMBOL MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or

caution. May be used in conjunction

with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and

follow all warnings and safety

instructions. Failure to do so can

result in serious injury to the

operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING: Thrown objects and

loud noise can cause severe eye

injury and hearing loss. Wear eye

protection meeting ANSI Z87.1-1989

standards and ear protection when

operating this unit.

Use a full face

shield when needed.

• KEEP BYSTANDERS AWAY

WARNING: Keep all bystanders,

especially children and pets, at least

50 feet (15 m.) from the operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

• OIL

Refer to operator's manual for the

proper type of oil.

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE

SEVERE INJURY

WARNING: Keep clear of blower

outlet. Never point the blower at

yourself or others. Objects can be

thrown from blower. Do not operate

unit without proper attachments and

guards in place.

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.

Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

SYMBOL MEANING

•ON/OFF STOP CONTROL

ON / START / RUN

•ON/OFF STOP CONTROL

OFF or STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or

cylinder. You may get burned. These

parts get extremely hot from

operation. When turned off they

remain hot for a short time.

• PRIMER BULB

Press the primer bulb, fully and

slowly, 10 times.

• BLOWERS – ROTATING

IMPELLER BLADES CAN

CAUSE SEVERE INJURY

WARNING: Stop the engine and

allow the impeller to stop before

opening the door, installing or

changing tubes, or before cleaning

or performing any maintenance.

• THROTTLE CONTROL

Indicates “HIGH” or “FASTEST” speed.

• THROTTLE CONTROL

Indicates “IDLE,” “LOW” or

“SLOWEST” speed.

RULES FOR SAFE OPERATION

APPLICATION

• Cleaning yards, garages, driveways, porches,

patios, around walls, fences and more

KNOW YOUR UNIT

Blower Tube

Blower

Outlet

Fuel

Cap

Throttle Control

Spark Plug

Starter Rope

Grip

Primer Bulb

Blue Lever

Air Filter

Cover

Muffler

Cover

Handle

ASSEMBLY INSTRUCTIONS

INSTALL AND REMOVE THE BLOWER TUBE

Install

To install the blower tube, simply push it into the blower

housing. Push it in until the tabs on the top and bottom

of the housing slide into the blower tube detents (Fig. 1).

Remove

To remove the blower tube, use a flat blade screwdriver

to lift the tabs and pull the tube out of the blower

housing (Fig. 1).

Tab

Blower

Tube

To prevent serious

personal injury, stop

the engine and allow the impeller to stop

before attaching or removing tubes.

WARNING:

Blower

Tube

Detent

Fig. 1

To prevent serious

personal injury or

damage to the unit, the blower tube must

be installed while operating this unit.

WARNING:

OIL AND FUEL INFORMATION

NOTE: Dispose of the old fuel/oil mix in accordance to

Federal, State and Local regulations.

OIL AND FUEL MIXING INSTRUCTIONS

Old and/or improperly mixed fuel are the main reasons

for the unit not running properly. Be sure to use fresh,

clean unleaded fuel. Follow the instructions carefully for

the proper fuel/oil mixture.

Definition of Blended Fuels

Today's fuels are often a blend of gasoline and

oxygenates such as ethanol, methanol, or MTBE (ether).

Alcohol-blended fuel absorbs water. As little as 1%

water in the fuel can make fuel and oil separate. It forms

acids when stored. When using alcohol-blended fuel,

use fresh fuel (less than 60 days old).

Using Blended Fuels

If you choose to use a blended fuel, or its use is

unavoidable, follow recommended precautions:

• Always use the fresh fuel mix explained in your

operator's manual

• Always agitate the fuel mix before fueling the unit

• Drain the tank and run the engine dry before storing

the unit

Using Fuel Additives

The bottle of 2-cycle oil that came with your unit

contains a fuel additive which will help inhibit corrosion

and minimize the formation of gum deposits. It is

recommended that you use our 2-cycle oil with this unit.

If unavailable, use a good 2-cycle oil designed for

air-cooled engines along with a fuel additive, such as

STA-BIL

Gas Stabilizer or an equivalent. Add 0.8 oz.

(23 ml.) of fuel additive per gallon of fuel according to the

instructions on the container. NEVER add fuel additives

directly to the unit's fuel tank.

Thoroughly mix the proper ratio of 2-cycle engine oil

with unleaded gasoline in a separate fuel can. Use a 40:1

fuel/oil ratio. Do not mix them directly in the engine fuel

tank. See the table below for specific gas and oil mixing

ratios.

NOTE: One gallon (3.8 liters) of unleaded gasoline mixed

with one 3.2 oz. (95 ml.) bottle of

2-cycle oil makes a 40:1 fuel/oil ratio.

UNLEADED GAS 2 CYCLE OIL

1 GALLON US

(3.8 LITERS)

3.2 FL. OZ.

(95 ml)

1 LITER 25 ml

MIXING RATIO - 40:1

Add fuel in a clean,

well ventilated

outdoor area. Wipe up any spilled fuel

immediately. Avoid creating a source of

ignition for spilt fuel. Do not start the engine

until fuel vapors dissipate.

WARNING:

Gasoline is

extremely

flammable. Ignited Vapors may explode.

Always stop the engine and allow it to cool

before filling the fuel tank. Do not smoke

while filling the tank. Keep sparks and open

flames at a distance from the area.

WARNING:

Remove fuel cap

slowly to avoid injury

from fuel spray. Never operate the unit

without the fuel cap securely in place

WARNING:

For proper engine

operation and

maximum reliability, pay strict attention to

the oil and fuel mixing instructions on the

2-cycle oil container. Using improperly mixed

fuel can severely damage the engine.

CAUTION:

STARTING/STOPPING INSTRUCTIONS

STARTING INSTRUCTIONS

Fig. 2

Fig. 3

STOPPING INSTRUCTIONS

1. To turn off the blower, move the throttle control lever all the

way to the right, past the idle position ( ) until it clicks.

Make sure you move the lever into the furthest right detent

in order to turn the unit off (Fig. 2).

1. Mix gas with oil. Fill fuel tank with fuel/oil mixture. See

Oil and Fuel Mixing Instructions.

2. Fully press and release the primer bulb 10 times,

slowly. Some amount of fuel should be visible in the

primer bulb (Fig. 2) and fuel lines. If you can’t see fuel

in the bulb, press and release the bulb as many times

as it takes before you can see fuel in it.

3. Place the blue lever in Position 1- Start (Fig. 3).

4. Place the unit in the starting position (Fig. 4). Move the

throttle control to the fast position ( ) (Fig. 2).

5. Pull the starter rope briskly 3 times.

6. Place the blue lever in Position 2- Run.

7. Pull the starter rope briskly 1 to 6 times to start the

engine.

8. Allow the engine to warm up for 15 to 30 seconds. The

unit is ready for use.

...

The engine does not start, go back to step 2.

...

The engine fails to start after a couple attempts, place

the blue lever in Position 2 and move the throttle

control to the fast position ( ). Pull the starter rope

briskly 3 to 8 times. The engine should start. If not, repeat.

IF WARM... If the engine is already warm, start the unit

with the blue lever in Position 2.

Starter

Rope

Fig. 4

Operate this unit only in a

well- ventilated outdoor

area. Carbon monoxide exhaust fumes can be

lethal in a confined area.

WARNING:

Avoid accidental starting.

Make sure you are in the

starting position when pulling the starter rope

(Fig. 4).

To avoid serious injury, the operator and unit

must be in a stable position while starting.

Do not set unit on any surface except a clean, hard

area while starting. Debris such as gravel, sand,

dust and grass could be picked up by the air

intake and thrown out by the discharge opening.

This could damage the unit, property, or cause

serious injury to bystanders or the operator.

WARNING:

Position 1

(Start)

Blue Lever

Throttle Control

Position 2

(Run)

Throttle

Control

Idle

()

Fast

()

Primer Bulb

Off

Top View

Blue

Lever

Starting

Position

OPERATING INSTRUCTIONS

HOLDING THE BLOWER

Before operating the unit, stand in the operating position.

Check for the following:

• Operator is wearing proper clothing, such as boots,

safety glasses or goggles, ear/hearing protection,

gloves, long pants and long sleeve shirt

• If the conditions are dusty, the operator is wearing a

dust mask or face mask

• The unit is in good working condition

• The tubes and guards are in place and secure

OPERATING TIPS

• Assure the unit is not directed at anybody or any loose

debris before starting the unit.

• Verify that the unit is in good working condition. Make

sure the tubes and guards are in place and secure.

• Always hold the unit securely when operating. Keep a

firm grip on the handle.

• To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

• Operate power equipment only at reasonable hours—

not early in the morning or late at night when people

might be disturbed. Comply with times listed in local

ordinances. Usual recommendations are 9:00 am to

5:00 pm, Monday through Saturday.

• To reduce noise levels, limit the number of pieces of

equipment used at any one time.

• To reduce noise levels, operate power blowers at the

lowest possible speed to do the job.

• Check your equipment before operation, especially the

muffler, air intakes and air filters.

• Use rakes and brooms to loosen debris before blowing.

• In dusty conditions, slightly dampen surfaces or use a

mister attachment when water is available.

• Conserve water by using power blowers instead of

hoses for many lawn and garden applications,

including areas such as screens, patios, grills, porches,

and gardens.

•Watch out for children, pets, open windows or freshly

washed cars, and blow debris safely away.

• Use the full blower nozzle extension so the air stream

can work close to the ground.

• Clean up after using blowers and other equipment.

Dispose of debris appropriately.

OPERATING AS A BLOWER

1 Use the blower for trees, shrubs, flower beds and

hard-to-clean areas (Fig. 5).

2. Use the unit around buildings and for other normal

cleaning procedures (Fig. 6).

3. Use the blower around walls, overhangs, fences and

screens.

Fig. 5

Fig. 6

To prevent serious

personal injury or

damage to the unit, make sure blower tubes

are in place before you operate the unit.

WARNING:

To avoid serious

personal injury,

wear goggles or safety glasses at all times

when operating this unit. Wear a face mask

or dust mask in dusty locations.

WARNING:

MAINTENANCE AND REPAIR INSTRUCTIONS

MAINTENANCE SCHEDULE

Perform these required maintenance procedures at the

frequency stated in the table. These procedures should

also be a part of any seasonal tune-up.

NOTE: Some maintenance procedures may require

special tools or skills. If you are unsure about

these procedures take your unit to any non-road

engine repair establishment, individual or

authorized service dealer.

NOTE: Maintenance, replacement, or repair of the

emission control devices and system may be

performed by any non-road engine repair

establishment, individual or authorized service

dealer.

In order to assure peak performance of your engine,

inspection of the engine exhaust port may be necessary

after 50 hours of operation. If you notice lost RPM, poor

performance or general lack of acceleration, this service

may be required. If you feel your engine is in need of this

inspection, refer service to any non-road engine repair

establishment, individual or authorized service dealer for

repair. DO NOT attempt to perform this process yourself

as engine damage may result from contaminants

involved in the cleaning process for the port.

FREQUENCY MAINTENANCE REQUIRED REFER TO

Before starting engine Fill fuel tank with fresh fuel Page 8

Every 10 hours Clean and re-oil air filter Page 11

Every 25 hours

Check and clean spark arrestor

Check spark plug condition and gap

Page 12

Page 13

Every 50 hours

Inspect exhaust port and spark arrestor screen for clogging or

obstruction to assure maximum performance levels

Page 12

AIR FILTER MAINTENANCE

Clean and re-oil the air filter every 10 hours of operation.

It is an important item to maintain. Failure to maintain the

air filter will VOID the warranty.

1. Remove the carburetor/air filter cover by pushing on

the tab, located to the right of the cover (Fig. 7).

2. Swing the air filter cover open. It will swing on the

hinges to the left of the cover (Fig. 8).

3. Remove the air filter (Fig. 8).

4. Wash the filter in detergent and water. Rinse the

filter thoroughly and allow it to dry (Fig. 9).

5. Apply enough clean SAE 30 motor oil to lightly coat

the filter (Fig. 10).

6. Squeeze the filter to spread and remove excess oil

(Fig. 11).

7. Reinstall the filter and close the air filter cover (Fig. 7).

NOTE: If the unit is operated without the air filter, you will

VOID the warranty.

Fig. 7

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

To prevent serious

injury, never perform

maintenance or repairs with unit running.

Always service and repair a cool unit.

Disconnect the spark plug wire to ensure that

the unit cannot start.

WARNING:

Air Filter

Cover

Tab

Air Filter

Fig. 8

Tab

MAINTENANCE AND REPAIR INSTRUCTIONS

Fig. 10

Fig. 11

SPARK ARRESTOR MAINTENANCE

1. The spark arrestor is located in the muffler, under the

engine cover. When facing the unit from the front, the

muffler and spark arrestor are positioned on the left

hand side (Fig. 12).

2. To access the muffler and spark arrestor, you must

remove the engine cover. Using a T-25 torx or

flathead screwdriver, remove the five engine screws

pictured in Figure 13.

NOTE: You will have to remove the spark plug to access

one of the engine cover screws (Screw 5) (Fig. 13).

3. Once the engine cover is removed, the muffler heat

shield is visible. Remove the three screws from the

shield with a Phillips screwdriver. Then remove and

store the heat shield to reveal the muffler.

4. Remove the remaining three screws that secure the

muffler deflector plate to the muffler. Also remove he

two bolts. Use a Phillips screwdriver for the screws and

a T-25 torx screwdriver for the muffler bolts (Fig. 14).

5. Remove the spark arrestor and clean it with a wire

brush. Replace it if it is damaged or if you are unable to

clean it thoroughly.

6. Reinstall spark arrestor and reattach the muffler

deflector plate with the bolts and screws.

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

Spark

Arrestor

Fig. 9

Fig. 12

Fig. 13

Muffler

and Spark

Arrestor

Spark

Plug

Removed

to Access

Screws

Screw 5

Fig. 14

Remove

Spark Plug

Heat

Shield

Muffler

Deflector Plate

Screw 5

7. Reinstall the heat shield using the three screws.

8. Put the engine cover back on the unit and reinsert the

five screws.

9. Reconnect the spark plug.

Muffler Bolts

MAINTENANCE AND REPAIR INSTRUCTIONS

REPLACING THE SPARK PLUG

Use a Champion RDJ7Y spark plug, or equivalent. The

correct air gap is 0.020 inch (0.5 mm). Remove the plug

after every 25 hours of operation and check its condition.

1. Stop the engine and allow it to cool. Grasp the plug

wire firmly and pull it from the spark plug.

2. Clean around the spark plug. Remove the spark plug

from the cylinder head by turning a 5/8-inch socket

counterclockwise.

3. Replace a cracked, fouled or dirty spark plug. Set

the air gap at 0.020 in. (0.5 mm) using a feeler gauge

(Fig. 15).

4. Install a correctly-gapped spark plug in the cylinder

head. Tighten by turning the 5/8-inch socket

clockwise until snug.

If using a torque wrench torque to:

110-120 in.•lb. (12.3-13.5 N•m)

Do not over tighten.

0.020 in.

(0.5 mm)

Fig. 15

Do not sand blast,

scrape or clean

electrodes. Grit in the engine could damage

the cylinder.

WARNING:

CLEANING THE UNIT

Use a small brush to clean off the outside of the unit.

Do not use strong detergents. Household cleaners that

contain aromatic oils such as pine and lemon, and

solvents such as kerosene, can damage plastic housing

or handle. Wipe off any moisture with a soft cloth.

STORAGE

• Never store a fueled unit where fumes may reach an

open flame or spark.

• Allow the engine to cool before storing.

• Store the unit locked up to prevent unauthorized use

or damage.

• Store the unit in a dry, well-ventilated area.

• Store the unit out of the reach of children.

LONG TERM STORAGE

If you plan on storing the unit for an extended time, use

the following storage procedure:

1. Drain all fuel from the fuel tank into a container with

the same 2-cycle fuel mixture. Do not use fuel that

has been stored for more than 60 days. Dispose of

the old fuel/oil mix in accordance to Federal, State

and Local regulations.

2. Start the engine and allow it to run until it stalls. This

ensures that all fuel has been drained from the

carburetor.

3. Allow the engine to cool. Remove the spark plug and

put 1 oz. (30 ml) of any high quality motor oil or

2-cycle oil into the cylinder. Pull the starter rope

slowly to distribute the oil. Reinstall the spark plug.

NOTE: Remove the spark plug and drain all of the oil

from the cylinder before attempting to start the

unit after storage.

4. Thoroughly clean the unit and inspect it for any loose

or damaged parts. Repair or replace damaged parts

and tighten loose screws, nuts or bolts. The unit is

ready for storage.

TRANSPORTING

• Allow the engine to cool before transporting.

• Drain fuel from unit.

• Tighten fuel cap before transporting.

• Secure the unit while transporting.

ACCESSORIES/ REPLACEMENT PARTS

2-Cycle Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147543

Spark Plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 610311

Fuel Cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180000

For specific replacement parts, refer to the parts list

located on the inside back cover of this manual.

To avoid serious

personal injury,

always turn your unit off and allow it to cool

before you clean or service it.

WARNING:

TROUBLESHOOTING

CAUSE ACTION

Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture

Air filter is plugged Replace or clean the air filter

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

CAUSE ACTION

Blue lever is in the incorrect position Refer to the Starting/Stopping instructions

Throttle lever is in the incorrect position Refer to the Starting/Stopping instructions

Empty fuel tank Fill fuel tank with properly mixed fuel

Primer bulb wasn't pressed enough Press primer bulb fully and slowly 10 times

Engine flooded Use starting procedure with the blue lever in Position 2

Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture

Fouled spark plug Replace or clean the spark plug

Plugged spark arrestor Clean or replace spark arrestor

ENGINE WILL NOT START

ENGINE WILL NOT IDLE

ENGINE WILL NOT ACCELERATE

ENGINE LACKS POWER OR STALLS

CAUSE ACTION

Air filter is plugged Replace or clean the air filter

Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture

CAUSE ACTION

Old or improperly mixed fuel Drain fuel tank / Add fresh fuel mixture

Dirty air filter Clean or replace the air filter

Plugged spark arrestor Clean or replace spark arrestor

If further assistance is required, contact your authorized service dealer.

SPECIFICATIONS

ENGINE*

Engine Type.......................................................................................................................................... Air-Cooled, 2-Cycle

Displacement............................................................................................................................................. 25 cc (1.4 cu. in)

Operating RPM........................................................................................................................................ 8,200 - 9,200 rpm

Idle Speed RPM ...................................................................................................................................... 3,200 - 5,200 rpm

Ignition Type.......................................................................................................................................................... Electronic

On/Off Stop Control................................................................................................................................ Throttle Kill Switch

Spark Plug Gap.................................................................................................................................... 0.020 inch (0.5 mm)

Lubrication................................................................................................................................................... Fuel/Oil Mixture

Fuel/Oil Ratio................................................................................................................................................................. 40:1

Carburetor....................................................................................................................................... Diaphragm, All-Position

Starter............................................................................................................................................................... Auto Rewind

Muffler..................................................................................................................................................... Baffled with Guard

Fuel Tank Capacity................................................................................................................................... 7 ounces (207 ml)

BLOWER*

Throttle Control............................................................................................................................................................ Lever

Blower Velocity....................................................................................................................... 180 mph minimum (290 kmh)

Blower Air Output..................................................................................................................................... 325 cfm (99 cmm)

Weight (no fuel, with blower tube) ........................................................................................................................9 lb. (4 kg)

*All specifications are based on the latest product information available at the time of printing. We reserve the right to

make changes at any time without notice.

NOTES

California / EPA Emission Control Warranty Statement

Your Warranty Rights and Obligations

The California Air Resource Board, the Environmental Protection Agency and Troy-Bilt LLC (Troy-Bilt) are pleased to

explain the emission control system warranty on your 2000 and later small off-road engine. New small off-road engines

must be designed, built and equipped to meet stringent anti-smog standards. Troy-Bilt must warrant the emission

control system on your small off-road engine for the periods of time listed below provided there has been no abuse,

neglect or improper maintenance of your small off-road engine.

Your emission control system may include parts such as the carburetor or fuel-injected system, the ignition system, and

catalytic converter. Also included may be hoses, belts, connectors and other emission-related assemblies.

Where a warrantable condition exists, Troy-Bilt will repair your small off-road engine at no cost to you including

diagnosis, parts and labor.

The 2000 and later small off-road engines are warranted for two years. If any emission-related part on your engine is

defective, the part will be repaired or replaced by Troy-Bilt.

Owners Warranty Responsibilities

• As the small off-road engine owner, you are responsible for the performance of the required maintenance listed in your

operator’s manual. Troy-Bilt recommends that you retain all receipts covering maintenance on your small off-road

engine, but Troy-Bilt cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of

all scheduled maintenance.

• As the small off-road engine owner, you however should be aware that Troy-Bilt may deny you warranty coverage if

your small off-road engine or a part has failed due to abuse, neglect, improper maintenance or unapproved

modifications.

• You are responsible for presenting your small off-road engine to a Troy-Bilt Authorized Service Center as soon as a

problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should call 1-800-520-5520.

Manufacturer’s Warranty Coverage

• The warranty period begins on the date the engine or equipment is delivered to the retail purchaser.

• The manufacturer warrants to the initial owner and each subsequent purchaser, that the engine is free from defects in

material and workmanship which cause the failure of a warranted part for a period of two years.

• Repair or replacement of warranted part will be performed at no charge to the owner at an Authorized Troy-Bilt Service

Center. For the nearest location please contact Troy-Bilt at: 1-800-520-5520.

• Any warranted part which is not scheduled for replacement, as required maintenance or which is scheduled for only

for regular inspection to the effect of “Repair or Replace as Necessary” is warranted for the warranty period. Any

warranted part which is scheduled for replacement as required maintenance will be warranted for the period of time up

to the first scheduled replacement point for that part.

• The owner will not be charged for diagnostic labor which leads to the determination that a warranted part is defective,

if the diagnostic work is performed at an Authorized Troy-Bilt Service Center.

• The manufacturer is liable for damages to other engine components caused by the failure of a warranted part still

under warranty.

• Failures caused by abuse, neglect or improper maintenance are not covered under warranty.

• The use of add-on or modified parts can be grounds for disallowing a warranty claim. The manufacturer is not liable to

cover failures of warranted parts caused by the use of add-on or modified parts.

• In order to file a claim, go to your nearest Authorized Troy-Bilt Service Center. Warranty services or repairs will be

provided at all Authorized Troy-Bilt Service Centers.

• Any manufacturer approved replacement part may be used in the performance of any warranty maintenance or repair

of emission related parts and will be provided without charge to the owner. Any replacement part that is equivalent in

performance or durability may be used in non-warranty maintenance or repair and will not reduce the warranty

obligations of the manufacturer

• The following components are included in the emission related warranty of the engine, air filter, carburetor, primer, fuel

lines, fuel pick up/ fuel filter, ignition module, spark plug and muffler.

MANUFACTURER’S LIMITED WARRANTY FOR:

No implied warranty, including any implied warranty of

merchantability or fitness for a particular purpose,

applies after the applicable period of express written

warranty above as to the parts as identified. No other

express warranty or guaranty, whether written or oral,

except as mentioned above, given by any person or

entity, including a dealer or retailer, with respect to any

product shall bind Troy-Bilt LLC During the period of

the Warranty, the exclusive remedy is repair or

replacement of the product as set forth above. (Some

states do not allow limitations on how long an implied

warranty lasts, so the above limitation may not apply to

you.)

The provisions as set forth in this Warranty provide the

sole and exclusive remedy arising from the sales. Troy-

Bilt LLC shall not be liable for incidental or

consequential loss or damages including, without

limitation, expenses incurred for substitute or

replacement lawn care services, for transportation or

for related expenses, or for rental expenses to

temporarily replace a warranted product. (Some states

do not allow limitations on how long an implied warranty

lasts, so the above limitation may not apply to you.)

In no event shall recovery of any kind be greater than the

amount of the purchase price of the product sold.

Alteration of the safety features of the product shall void

this Warranty. You assume the risk and liability for loss,

damage, or injury to you and your property and/or to

others and their property arising out of the use or misuse

or inability to use the product.

This limited warranty shall not extend to anyone other than

the original purchaser, original lessee or the person for

whom it was purchased as a gift.

How State Law Relates to this Warranty: This warranty

gives you specific legal rights, and you may also have

other rights which vary from state to state.

To locate your nearest service dealer dial

1-800-520-5520.

Troy-Bilt LLC

P.O. Box 361131

Cleveland, OH 44136-0019

The limited warranty set forth below is given by Troy-Bilt

LLC with respect to new merchandise purchased and used

in the United States, its possessions and territories.

Troy-Bilt LLC warrants this product against defects in

material and workmanship for a period of two (2) years

commencing on the date of original purchase and will, at its

option, repair or replace, free of charge, any part found to

be defective in material or workmanship. This limited

warranty shall only apply if this product has been operated

and maintained in accordance with the Operator’s Manual

furnished with the product, and has not been subject to

misuse, abuse, commercial use, neglect, accident,

improper maintenance, alteration, vandalism, theft, fire,

water or damage because of other peril or natural disaster.

Damage resulting from the installation or use of any

accessory or attachment not approved by Troy-Bilt LLC for

use with the product(s) covered by this manual will void

your warranty as to any resulting damage. This warranty is

limited to ninety (90) days from the date of original retail

purchase for any Troy-Bilt product that is used for rental or

commercial purposes, or any other income-producing

purpose.

HOW TO OBTAIN SERVICE: Warranty service is

available, WITH PROOF OF PURCHASE THROUGH

YOUR LOCAL AUTHORIZED SERVICE DEALER. To locate

the dealer in your area, visit our website at www.troybilt.com,

check for a listing in the Yellow Pages, call 1-800-520-

5520 or write to

P.O. Box 361131, Cleveland, OH 44136-

0019

This limited warranty does not provide coverage in

the following cases:

A. Tune-ups - Spark Plugs, Carburetor Adjustments,

Filters

B. Wear items - Bump Knobs, Outer Spools, Cutting

Line, Inner Reels, Starter Pulley, Starter Ropes, Drive

Belts

C. Troy-Bilt LLC does not extend any warranty for

products sold or exported outside of the United

States of America, its possessions and territories,

except those sold through Troy-Bilt’s authorized

channels of export distribution.

Troy-Bilt LLC reserves the right to change or improve the

design of any Troy-Bilt Product without assuming any

obligation to modify any product previously manufactured.

Souffleuse

à 2-temps

Modèle TB250B

Manuel de L'utilisateur

P/N 769-01169 (4/04)

IMPRIMÉ AUX ÉTATS-UNIS

MANUEL IMPORTANT À NE PAS JETER

INTRODUCTION

Copiez le numéro

de série ici :

Copiez le numéro de

modèle / pièce mère ici :

TOUS NOS REMERCIEMENTS

Nous vous remercions d'avoir acheté ce produit de

qualité. Cet outil mécanique de plein air moderne est

conçu pour vous rendre service pendant longtemps. Il

vous sauvera beaucoup de temps comme vous pourrez

vous en rendre compte. Ce manuel de l'utilisateur

comporte un mode d'emploi facile à comprendre. Prenez

soin de lire le manuel au complet et suivez toutes ses

instructions à la lettre afin de conserver votre nouvel outil

mécanique de plein air en excellent état de

fonctionnement.

RÉFÉRENCES, ILLUSTRATIONS ET

SPÉCIFICATIONS RELATIVES AU PRODUIT

Toutes les informations, illustrations et spécifications

contenues dans ce manuel tiennent compte des dernières

informations techniques disponibles au moment de

mettre sous presse. Nous nous réservons le droit d'y

apporter des modifications à tout moment, sans préavis.

réservés.

NFORMATIONS D’ENTRETIEN

Tout entretien effectué sur cet appareil pendant et après

la période de garantie doit être fait par un concess-

ionnaire agréé uniquement. Obtenez la liste des

concessionnaires agréés appelez le 1-800-520-5520.

Pour de plus amples informations à propos de votre

appareil, visitez www.troybilt.com.

NE RETOURNEZ PAS L'APPAREIL AU DÉTAILLANT

CHEZ QUI VOUS L'AVEZ ACHETÉ. TOUT SERVICE

SOUS GARANTIE NÉCESSITE UNE PREUVE D'ACHAT.

Avant d'assembler votre nouvel équipement, repérez la

plaque signalétique de l'appareil et copiez ses

informations dans l'espace ci-dessous. Ces informations

sont essentielles si vous désirez obtenir de l'aide auprès

de notre service technique ou d'un distributeur agréé. Un

exemple de plaque signalétique est présenté ci-dessous.

S/N :

ITEM :

MODEL :

Prenez soin de lire et de bien comprendre ce manuel

avant de démarrer ou de faire fonctionner cet équipement.

CE PRODUIT EST COUVERT PAR UN OU PLUSIEURS

BREVETS AMÉRICAINS, ET D’AUTRES SONT EN

INSTANCE.

TABLE DES MATIÈRES

Service technique . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Consignes de sécurité . . . . . . . . . . . . . . . . . . . . . . .3

Familiarisez-vous avec votre appareil . . . . . . . . . . .6

Instructions de montage . . . . . . . . . . . . . . . . . . . . . .7

Informations sur l'huile et le carburant . . . . . . . . . . .8

Instructions de démarrage et d'arrêt . . . . . . . . . . . .9

Mode d'emploi . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

Entretien et réparations . . . . . . . . . . . . . . . . . . . . .11

Accessoires/pièces de rechange . . . . . . . . . . . . . .13

Nettoyage et entreposage . . . . . . . . . . . . . . . . . . .13

Tableau de dépannage . . . . . . . . . . . . . . . . . . . . . .14

Caractéristiques . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Garantie . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Liste des pièces . .Intérieure de la Couverture Arrière

PARE-ÉTINCELLES

REMARQUE : à l'intention des utilisateurs opérant

dans les terres forestières des États-Unis et dans les

états de Californie, du Maine, de l'Orégon et de

Washington. Toutes les terres forestières des États-Unis

et de l'état de Californie (Codes sur les ressources

publiques 4442 et 4443), de l'Orégon et de Washington

exigent de par la loi que certains moteurs à combustion

interne utilisés dans des zones couvertes de taillis ou

d'herbe soient équipés d'un pare-étincelles en parfait état

de fonctionnement, ou qu'ils soient conçus, équipés et

entretenus pour la prévention des incendies. Renseignez-

vous auprès des autorités de votre province ou de votre

municipalité concernant la réglementation en vigueur.

Vous pourriez être passible d'une amende ou être tenu

responsable si vous ne respectez pas cette

réglementation. Cet appareil est équipé d'un pare-

étincelles en usine. Si l'écran pare-étincelles, doit être

remplacé, communiquez avec le service technique.

AVERTISSEMENT

LES GAZ D'ÉCHAPPEMENT DU MOTEUR DE

CET APPAREIL CONTIENNENT DES PRODUITS

CHIMIQUES CONSIDÉRÉS PAR L'ÉTAT DE

CALIFORNIE COMME POUVANT CAUSER LE

CANCER, DES MALFORMATIONS

CONGÉNITALES OU D'AUTRES EFFETS NOCIFS

SUR L'APPAREIL DE REPRODUCTION.

AVERTISSEMENT DE LA PROPOSITION 65 DE

CALIFORNIE

Numéro de modèle

Numéro de série

Numéro de pièce mère

La page est en cours de chargement...

MTD TB250 Le manuel du propriétaire

Marque: MTD

Modèle: TB250

Catégorie: Souffleurs / sécheurs d'air

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: MTD TB250 Owner's manual
español: MTD TB250 El manual del propietario

Documents connexes

MTD 769.01408 Manuel utilisateur

MTD TB250 Le manuel du propriétaire

MTD TB250 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents