GE AEM10AN Le manuel du propriétaire

Safety Instructions ................... 2, 3

Operating Instructions

............. 4, 5

Care and Cleaning

Air Filter .............................................................6

Outdoor Coils ..................................................6

Installation Instructions ......7–12

Troubleshooting Tips ................. 14

Normal Operating Sounds ....................14

Consumer Support

Consumer Support ................. Back Cover

Ownership Registration for

Customers in Canada only ...........15, 16

Warranty for Customers

in Canada ......................................................17

Warranty for Customers

in the U.S.A. ...................................................18

49-7623 12-09 GE

AEM10*

AEM12*

Owner’s Manual and

Installation Instructions

Write the model and serial numbers here:

Model # _________________________

Serial # __________________________

Find these numbers on a label on the side of

the air conditioner.

Air Conditioners

GEAppliances.com

Room

As an EnErgy Star® partner, GE has

determined that this product meets

the EnErgy Star® guidelines for

energy efficiency.

*EnErgy Star® labeled product

Climatiseur

Acondicionador

de aire

Manuel d’utilisation et

instructions d’installation

Manual del propietario

y instrucciones de

instalación

La section française commence à la page 19

La sección en español empieza en la página 35

2

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

For your safety, the information in this manual must be followed to minimize the risk of fire, electric

shock or personal injury.

n Use this appliance only for its intended

purpose as described in this Owner’s

Manual.

n This air conditioner must be properly

installed in accordance with the Installation

Instructions before it is used.

n Never unplug your air conditioner by pulling

on the power cord. Always grip plug firmly

and pull straight out from the receptacle.

n Replace immediately all electric service

cords that have become frayed or otherwise

damaged. A damaged power supply cord

must be replaced with a new power supply

cord obtained from the manufacturer and

not repaired. Do not use a cord that shows

cracks or abrasion damage along its length

or at either the plug or connector end.

n If the receptacle does not match the plug,

the receptacle must be changed out by a

qualified electrician.

n Turn the unit OFF and unplug your air

conditioner before making any repairs

or cleaning.

NOTE: We strongly recommend that any

servicing be performed by a qualified

individual.

n For your safety…do not store or use

combustible materials, gasoline or other

flammable vapors or liquids in the vicinity

of this or any other appliance.

n All air conditioners contain refrigerants,

which under federal law must be removed

prior to product disposal. If you are getting

rid of an old product with refrigerants, check

with the company handling disposal about

what to do.

n These R410A air conditioning systems

require contractors and technicians to use

tools, equipment and safety standards

approved for use with this refrigerant.

DO NOT use equipment certified for R22

refrigerant only.

SAFETY PRECAUTIONS

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

For personal safety, this appliance must be

properly grounded.

DO NOT use an adapter plug with this

appliance.

The power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates

with a standard 3-prong (grounding) wall outlet

to minimize the possibility of electric

shock hazard from this appliance.

Power cord includes a current interrupter device.

A test and reset button is provided on the plug

case. The device should be tested on a periodic

basis by first pressing the TEST button and then

the RESET button while plugged into the outlet. If

the TEST button does not trip

or if the RESET button will not stay engaged,

discontinue use of the air conditioner and

contact a qualified service technician.

Have the wall outlet and circuit checked by

a qualified electrician to make sure the outlet

is properly grounded.

Where a 2-prong wall outlet is encountered,

it is your personal responsibility and obligation to

have it replaced with a properly grounded

3-prong wall outlet.

The air conditioner should always be plugged

into its own individual electrical outlet which has

a voltage rating that matches the rating plate.

This provides the best performance and also

prevents overloading house wiring circuits which

could cause a fire hazard from overheated wires.

See the Installation Instructions, Electrical

Requirements section for specific electrical

connection requirements.

HOW TO CONNECT ELECTRICITY

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

3

Consumer Support

Troubleshooting

Tips

Installation

Instructions

Care and Cleaning

Operating

Instructions

Safety Instructions

GEAppliances.com

WARNING!

Because of potential safety hazards under certain

conditions, we strongly recommend against the

use of an extension cord.

However, if you must use an extension cord,

it is absolutely necessary that it be a UL-listed,

14 gauge, 3-wire grounding type appliance

extension cord having a grounding type plug

and outlet and that the electrical rating of the

cord be 15 amperes (minimum) and 125 volts.

CAUTION:

DO NOT use an extension cord with any of the

230/208 volt models.

USE OF EXTENSION CORDS—115-Volt models only

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

4

About the controls on the air conditioner

Controls

Power Pad

Turns air conditioner on and off. When turned

on, the display will show the room temperature.

Display

Shows the room temperature or time remaining

on the Delay timer. Shows the Set temperature

while setting the temperature in Cool or Energy

Saver modes. The Set light will turn on while

setting.

NOTE: The display will change to show the room

temperature after settings have been made.

To recall the Set temperature, press the Temp

Increase or Decrease pads.

Temp Increase /DecreasePads

Use to set temperature when in Cool or Energy

Saver mode. The Set light will turn on while

setting.

Delay Timer Increase (+) /Decrease(–)

Pads

Each touch of the Increase / Decrease pads

on the unit or the Increase + / Decrease – pads

on the remote control will set the delay time

when using the Delay 1–24hr timer (+). The Set

light will turn on while setting.

Fan Speed Pads

Use to set the fan speed to Low, Med, High

or Auto on the unit. NOTE: On the remote

control, use the fan speed Increase + /

Decrease – pads to set the fan speeds to Low,

Med or High. Use the Auto pad to turn Auto

fan on.

Mode Pad

Use to set the air conditioner to Cool, Energy

Saver or Fan Only mode.

Delay Pads

Delay ON—When the air conditioner is off, it can

be set to automatically come on in 1 to 24 hours

at its previous mode and fan settings.

Delay OFF—When the air conditioner is on,

it can be set to automatically turn off in 1 to

24 hours.

How to set:

Press the Delay 1–24hr pad on the unit or the

+ pad on the remote control. Each touch of the

Increase / Decrease pads on the unit or the

Increase + / Decrease – pads on

the remote control will set the timer in

1-hour intervals. The Set light will turn on while

setting.

To review the remaining time on the Delay

1–24hr timer, press the Delay 1–24hr pad on the

unit or the

+ pad on the remote control. Use the

Increase / Decrease pads on the unit or the

Increase + / Decrease – pads on the remote

control to set a new time if desired.

To cancel the timer, press the Delay

1–24hr pad until the light on the Delay 1–24hr

pad goes off.

Features and appearance will vary.

Lights next to the touch pads on the air conditioner control panel indicate the selected settings.

The display always shows

the room temperature

except when setting the

Set temperature or the

Delay timer.

Air Conditioner Controls

Light indicates the delay timer is set.

Light indicates the unit

is in the temperature or

delay time Set mode.

In the case of a power outage or interruption, the

unit will automatically re-start in the settings last

used after the power is restored. If the Delay 1–24hr

feature was set, it will resume countdown. You may

need to set a new time if desired.

Power Outage Recovery Feature

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

Remote Control

FanFan

5

GEAppliances.com

Cool Mode

Use the Cool mode at Low, Med, High or Auto Fan

Speed for cooling. Use the Temperature Increase 

/ Decrease  pads to set the desired temperature

between 64°F and 86°F in 1°F increments.

An electronic thermostat is used to maintain the room

temperature. The compressor will cycle on

and off to keep the room at the set level of comfort.

Set the thermostat at a lower number and the indoor

air will become cooler. Set the thermostat at a higher

number and the indoor air will become warmer.

NOTE: If the air conditioner is off and is then turned on

while set to a Cool setting or if turned from a fan

setting to a Cool setting, it may take approximately

3 minutes for the compressor to start and cooling to

begin.

Cooling Descriptions

For Normal Cooling—Select the Cool mode and

High or Med fan with a middle set temperature.

For Maximum Cooling—Select the Cool mode

and High fan with a lower set temperature.

For Quieter & Nighttime Cooling—Select the

Cool mode and Low fan with a middle set

temperature.

Do Not Operate in Freezing Outdoor Conditions

This cool-only air conditioner was not designed for

freezing outdoor conditions. It must not be used in

freezing outdoor conditions.

Fan Only Mode

Use the Fan Only Mode at Low, Med or High fan

speed to provide air circulation and filtering without

cooling. Since fan only settings do not provide cooling,

a Set temperature cannot be entered. The room

temperature will appear in the display.

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Energy Saver Mode

Controls the fan.

ON—The fan will cycle on and off with the

compressor. This results in wider variations of room

temperature and humidity. Normally used when the

room is unoccupied. NOTE: The fan may continue to

run for a short time after the compressor cycles off.

OFF—The fan runs all the time, while the compressor

cycles on and off.

Set to Auto fan speed for the fan speed to

automatically set to the speed needed to provide

optimum comfort settings with the set temperature.

If the room needs more cooling, the fan speed

will automatically increase. If the room needs less

cooling, the fan speed will automatically decrease.

NOTE: Auto Fan Speed cannot be used when in the

Fan Only Mode.

Auto Fan Speed

n To ensure proper operation, aim the remote

control at the signal receiver on the air

conditioner.

n The remote control signal has a range of

up to 20 feet.

n Make sure nothing is between the air conditioner

and the remote control that could block the

signal.

n Make sure batteries are fresh and installed

correctly as indicated on the remote control.

Remote Control

Consumer Support

Troubleshooting

Tips

Installation

Instructions

Care and Cleaning

Operating

Instructions

Safety Instructions

Use the levers to adjust the air direction left and right.

Fingertip pressure on the louver banks adjusts the air

direction up or down.

Air Direction

Outdoor Coils

The coils on the outdoor side of the air conditioner

should be checked regularly. If they are clogged with

dirt or soot, they may be professionally cleaned.

6

Turn the air conditioner off and remove the plug from

the wall outlet before cleaning.

To clean, use water and a mild detergent. Do not use

bleach or abrasives.

Grille and Case

Care and cleaning of the air conditioner.

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

1

Remove the battery cover by sliding it according

to the arrow direction.

2

Insert new batteries, making sure that the (+)

and (–) of battery are installed correctly.

3

Reattach the cover by sliding it back

into position.

NOTES:

n Use 2 “AAA” (1.5 volt) alkaline batteries. Do not

use rechargeable batteries.

n Remove the batteries from the remote control if

the system is not going to be used for a long time.

n Do not mix old and new batteries. Do not mix

alkaline, standard (carbon-zinc) or rechargeable

(ni-cad, ni-mh, etc) batteries.

How to Insert the Batteries in the Remote Control

Air Filter

The air filter behind the front grille should be checked

and cleaned at least every 30 days or

more often if necessary.

To remove:

Open the inlet grille by pulling downward on the tabs

at the top upper corners of the inlet grille until the

grille is in a 45° position. Remove the filter.

Clean the filter with warm, soapy water. Rinse and let

the filter dry before replacing it. Do not clean the filter

in a dishwasher.

CAUTION: DO NOT operate the air

conditioner without a filter because dirt and lint will

clog it and reduce performance.

BEFORE YOU BEGIN

Read these instructions completely

and carefully.

•

IMPORTANT — Save these instructions

for local inspector’s use.

•

IMPORTANT — Observe all governing

codes and ordinances.

• Note to Installer – Be sure to leave these

instructions with the Consumer.

• Note to Consumer – Keep these instructions for

future reference.

• Skill level – Installation of this appliance requires

basic mechanical skills.

• Completion time –

Approximately 1 hour

• We recommend that two people install

this product.

• Proper installation is the responsibility

of the installer.

• Product failure due to improper installation is not

covered under the Warranty.

• You MUST use all supplied parts and use proper

installation procedures as described in these

instructions, and any separate kit instructions,

when installing this air conditioner.

Installation

Air Conditioner

Instructions

Some models require a 115/120-volt AC,

60 Hz grounded outlet protected with a

15-amp time delay fuse or circuit breaker.

The 3-prong grounding plug minimizes the possibility

of electric shock hazard. If the wall outlet you plan to

use is only a 2-prong outlet,

it is your responsibility to have it replaced with

a properly grounded 3-prong wall outlet.

Some models require 230/208-volt AC,

protected with a time delay fuse or circuit

breaker. These models should be installed

on their own single branch circuit for best

performance and to prevent overloading

house or apartment wiring circuits, which

could cause a possible fire hazard from

overheating wires.

ELECTRICAL REQUIREMENTS

CAUTION:

Do not, under any circumstances, cut or remove

the third (ground) prong from the power cord.

Do not change the plug on the power cord

of this air conditioner.

Aluminum house wiring may present special

problems—consult a qualified electrician.

If the sill support bolts do not contact the

window sill, or if you have a window without

a sill, you must order accessory kit RAK87

to properly install this air conditioner. Call

800.626.2002 or visit GEAppliances.com.

Power cord includes a current interrupter device. A

test and reset button is provided on the plug case. The

device should be tested on a periodic basis by first

pressing the TEST button and then the RESET button

while plugged into the outlet. If the TEST button does

not trip or if the RESET button will not stay engaged,

discontinue use of the air conditioner and contact a

qualified service technician.

7

TOOLS YOU WILL NEED

Phillips head screwdriver

Ruler or tape measure

Pencil

Level

Scissors or knife

Adjustable wrench

Flat-blade screwdriver

Questions? Call 800.GE.CARES (800.432.2737) or visit our Website at: GEAppliances.com

In Canada, call 1.800.561.3344 or visit www.GEAppliances.ca

8

Type A (6)

Type B (7)

Right

accordion

panel

Window sash seal

(thin, adhesive-backed)

Foam top

window gasket

Window locking

bracket (2)

Left accordion

panel

Top mounting rail

Installation Instructions

PARTS INCLUDED

(appearance may vary)

Type C (6)

Type D (3)

Top mounting rail

seal strip

Sill support (2)

Nut (2)

Bolt (2)

Installation Instructions

WINDOW REQUIREMENTS

• These instructions are for a standard

double-hung window. You will need to modify

them for other types of windows.

CAUTION:

If the sill support

bolts do not contact the window sill, or

if you have a window without a sill, you

must order accessory kit RAK87 to

properly install this air conditioner.

Call 800.626.2002 or visit GEAppliances.com.

• The air conditioner can be installed without

the accordion panels if needed to fit in a

narrow window. See the window opening

dimensions.

• All supporting parts must be secured

to firm wood, masonry or metal.

• The electrical outlet must be within reach of

the power cord.

1

15 7/16” min.

25 1/4″ to 38″

(With accordion panels)

REMOVE THE AIR CONDITIONER

FROM THE CASE

Remove and save the 2 screws from the lower

sides of the front grille.

Grasp the lower corners of the grille while

pressing in on the case sides with your finger

tips. Pull out to release and lift it up.

NOTE: Do not pull the bottom edge toward you

more than 3″ or you may damage the tabs of

the grille.

Remove the ground screw from each side of

the case. Keep them in a safe location.

NOTE: Be sure to save these screws. You will

need them later in the installation.

Slide the air conditioner from the case by

gripping the base pan handle and pulling

forward while bracing the case. Do not pull or

lift on the styrofoam discharge area.

3

A

C

FRONT

Do not

pull or

lift in this

area—

damage

to the

unit may

result

D

STORM WINDOW REQUIREMENTS

A storm window frame will not allow the air

conditioner to tilt toward the outside, and will keep

it from draining properly. To adjust for this, attach

a piece of wood to the sill.

WOOD PIECES –

WIDTH: 2″

LENGTH: Long enough to fit inside the window

frame.

THICKNESS: To determine the thickness, place a

piece of wood on the sill to make it 1/2″ higher

than the top of the storm window frame or the

vinyl frame.

Attach securely with nails or screws provided

by the installer.

2

1/2″ higher

than storm

window

frame

Storm window

frame

Wood

Sill

1/2″ higher

than vinyl frame

(on some windows)

Vinyl frame

9

FRONT

B

2

Installation Instructions

10

INSTALL THE TOP MOUNTING RAIL

ONTO THE CASE

Attach the top mounting rail onto the top of the

case with 3 Type B screws.

5

Type B

screws

Top

mounting

rail

INSTALL THE

SIDE ACCORDION PANELS

Slide the left and right accordion panels into

the top and bottom mounting rails.

Attach the accordion panels to the case using 3

Type A screws on each side.

6

A

B

Type A

screws

Top mounting rail

Bottom mounting rail

Accordion

panel

PREPARE THE WINDOW

• Cut the window sash seal to the window

width and stick the adhesive side to the

bottom of the sash.

7

Window sash

seal

BACK

INSIDE

4

Top mounting rail

Remove

backing

from seal

strip

3/8″ overlap 3/8″ overlap

Top mounting rail

Seal strip

FRONT VIEW

ATTACH THE TOP MOUNTING RAIL

SEAL STRIP

Remove the backing from the top mounting rail

seal strip and attach the seal strip to the bottom

of the top maounting rail, along the front edge.

Installation Instructions

INSTALL THE CASE IN THE WINDOW

Open the window and mark the centerline of

the window sill.

Carefully place the case on the window stool

and align the center mark on the bottom front

with the centerline of the sill.

Pull the window down behind the top mounting

rail.

NOTE: Do not shut the window so tightly that

movement of the accordion panels is

restricted.

Select the position that will place the sill

supports near the outermost point on the sill.

Place the short side of the sill supports, on the

case bottom, toward the window. Attach the sill

supports to the case track hole in relation to the

selected position using 2 Type B screws in each

support.

CAUTION: Do not install this air

conditioner in a window if the bolts do not

contact the window sill.

Adjust the bolt and the nut in each support so

that the case is installed with a slight tilt to the

outside. Use a level; no more than 1/2 bubble

will be the correct case slant to the outside.

CAUTION: If the sill support bolts

do not contact the window sill or if you have a

window without a sill you must order accessory

kit RAK87 to properly install this air conditioner.

Call 800.626.2002 or visit GEAppliances.com.

8

INSTALL THE CASE IN THE WINDOW

(CONT.)

Secure the case to the window sill by using 3

Type D screws.

Pull the accordion panels to each window sash

track. Attach them on each side to the window

sash and the window sill using

4 Type C screws.

8

A

B

C

F

G

11

D

Long side of

sill supports

OUTSIDE

E

Installation Instructions

INSTALL THE AIR CONDITIONER

IN THE CASE (CONT.)

Replace the 2 ground screws removed earlier,

one on each side of the case.

IMPORTANT: The ground screws must be

reinstalled to ensure a proper ground.

Attach the front grille to the case by inserting

the tabs on the grille into the slots on the front

top of the case. Push the grille in.

Secure the front grille to the case by replacing

the 2 screws removed earlier. Press on the top

of the grille to help

with side screw installation.

Connect power.

10

B

C

INSTALL THE AIR CONDITIONER

IN THE CASE

Slide the air conditioner into the case by

the base pan. Do not push on the controls,

styrofoam air discharge housing or the finned

coils. Make sure the air conditioner is firmly

seated.

10

A

E

D

Do not press on

these areas—

damage to the unit

may result

Base Pan

12

9

INSTALL SUPPORT BRACKET AND

FOAM TOP WINDOW GASKET

Attach the support bracket

with one Type C screw.

Cut the foam top window gasket to the window

width.

Stuff the foam

between the glass

and the window

to prevent air and

insects from getting

into the room.

NOTE: If the gasket supplied does not fit your

window, obtain appropriate material locally to

provide a proper installation seal.

A

CAUTION:

To prevent broken glass or

damage to windows, on

vinyl or other similarly

constructed windows,

attach the support bracket

to the window side jam.

B

C

Wood

Vinyl

Consumer Support

Troubleshooting

Tips

Installation

Instructions

Care and Cleaning

Operating

Instructions

Safety Instructions

Troubleshooting Tips.

Normal Operating Sounds

n You may hear a pinging noise caused by

water being picked up and thrown against the

condenser on rainy days or when the humidity

is high. This design feature helps remove

moisture and improve efficiency.

n You may hear the thermostat click when the

compressor cycles on and off.

n Water will collect in the base pan during

high humidity or on rainy days. The water

may overflow and drip from the outdoor side

of the unit.

n The fan may run even when the compressor

does not.

Problem Possible Causes What To Do

Air conditioner The air conditioner • Make sure the air conditioner plug is pushed

does not start is unplugged. completely into the outlet.

The fuse is blown/circuit • Check the house fuse/circuit breaker box and replace

breaker is tripped. the fuse or reset the breaker.

Power failure. • The unit will automatically re-start in the settings last

used after the power is restored.

• There is a protective time delay (approximately

3 minutes) to prevent tripping of the compressor

overload. For this reason, the unit may not start

normal cooling for 3 minutes after it is turned

back on.

The current interrupter • Press the RESET button located on the power cord plug.

device is tripped.

• If the RESET button will not stay engaged, discontinue

use of the air conditioner and contact a qualified

service technician.

Air conditioner does Airflow is restricted. • Make sure there are no curtains, blinds or furniture

not cool as it should blocking the front of the air conditioner.

The temp control may • On models with touch pads: In the Cool mode, press the

not be set correctly. Decrease pad.

• On models with control knobs, turn the temperature

knob to a higher number.

The air filter is dirty. • Clean the filter at least every 30 days.

See the Care and Cleaning section.

The room may have been hot. • When the air conditioner is first turned on, you need

to allow time for the room to cool down.

Cold air is escaping. • Check for open furnace registers and cold air returns.

Cooling coils have iced up. • See “Air conditioner freezing up” below.

Air conditioner Ice blocks the air flow • On models with control knobs, set the mode control at

freezing up and stops the air conditioner High Fan or High Cool with the Temp at 1 or 2.

from cooling the room.

• On models with touch pads, set the controls at High Fan

or High Cool and set the thermostat to a higher

temperature.

The remote control The batteries are inserted • Check the position of the batteries. They should be

is not working incorrectly. inserted in the opposite (+) and (–) direction.

The batteries may be dead. • Replace the batteries.

Water drips outside Hot, humid weather. • This is normal.

Water drips indoors The air conditioner is not • For proper water disposal, make sure the air conditioner

tilted to the outside. slants slightly from the case front to the rear.

Water collects in Moisture removed from air • This is normal for a short period in areas with little

base pan and drains into base pan. humidity; normal for a longer period in very humid areas.

14

Notes.

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

15

OWNERSHIP REGISTRATION

P.O. BOX 1780

MISSISSAUGA, ONTARIO

L4Y 4G1

(FOR CANADIAN CONSUMERS ONLY)

Please place in envelope and mail to:

Veuillez mettre dans une enveloppe et envoyez à :

16

17

Consumer Support

Troubleshooting

Tips

Installation

Instructions

Care and Cleaning

Operating

Instructions

Safety Instructions

Staple your receipt here.

Proof of the original purchase

date is needed to obtain

service under the warranty.

GE Air Conditioner—One-Year Limited Warranty. (For customers in the U.S.A.)

For The Period Of: GE Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, GE will also provide, free of charge, all labor and related

original purchase service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

®

technician. To schedule service,

visit us on-line at GEAppliances.com, or call 800.GE.CARES

(800.432.2737). Have serial number and model number available

when calling for service.

n Service trips to your home to teach you how to

use the product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased for

home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is

not available, you may be responsible for a trip charge or you may be required to bring the product to an

Authorized GE Service location for service. In Alaska, the warranty excludes the cost of shipping or service

calls to your home.

Some states do not allow the exclusion or limitation of incidental or consequential damages. This warranty

gives you specific legal rights, and you may also have other rights which vary from state to state. To know

what your legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.

Warrantor: General Electric Company. Louisville, KY 40225

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in

this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

18

Staple your receipt here.

Proof of the original purchase

date is needed to obtain

service under the warranty.

GE Air Conditioner—One-Year Limited Warranty. (For customers in the Canada)

For The Period Of: Mabe Will Replace:

One Year Any part of the air conditioner which fails due to a defect in materials or workmanship.

From the date of the During this limited one-year warranty, Mabe will also provide, free of charge, all labor and

original purchase related service to replace the defective part.

All warranty service provided by our Factory Service Centers,

or an authorized Customer Care

®

technician. For service, call

1.800.561.3344. Please have serial number and model number

available when calling for service.

n Service trips to your home to teach you how to

use the product.

n Improper installation, delivery or maintenance. If you

have an installation problem, or if the air conditioner

is of improper cooling capacity for the intended use,

contact your dealer or installer. You are responsible

for providing adequate electrical connecting facilities.

n Failure of the product resulting from modifications to

the product or due to unreasonable use including failure

to provide reasonable and necessary maintenance.

n In commercial locations, labor necessary to move the

unit to a location where it is accessible for service

by an individual technician.

n Replacement of house fuses or resetting of circuit

breakers.

n Failure due to corrosion on models not corrosion-

protected.

n Damage to the product caused by improper power

supply voltage, accident, fire, floods or acts of God.

n Incidental or consequential damage caused by possible

defects with this air conditioner.

n Damage caused after delivery.

What Is Not Covered:

This warranty is extended to the original purchaser and any succeeding owner for products purchased in

Canada for home use within Canada. In-home warranty service will be provided in areas where it is available

and deemed reasonable by Mabe to provide.

Some provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above

exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other

rights which vary from province to province. To know what your legal rights are in your province, consult your

local or provincial consumer affairs office.

Warrantor: Mabe Canada Inc.,

Burlington, Ontario

EXCLUSION OF IMPLIED WARRANTIES—Your sole and exclusive remedy is product repair as provided in

this Limited Warranty. Any implied warranties, including the implied warranties of merchantability or

fitness for a particular purpose, are limited to one year or the shortest period allowed by law.

Safety Instructions

Operating

Instructions

Care and Cleaning

Installation

Instructions

Troubleshooting

Tips

Consumer Support

Consignes de sécurité ..........20, 21

Consignes d’utilisation

Modèles dotés touches

à effleurement ....................22, 23

Entretien et nettoyage

Filtre à air ..........................24

Serpentins extérieurs .................24

Instructions de montage ........25–30

Conseils de dépannage ............31

Bruits normaux de fonctionnement .....31

Assistance à la clientèle

Assistance à la clientèle ................36

Garantie ............................35

Enregistrement du titre

de propriété .....................33, 34

Inscrivez ici les numéros de modèle et de série :

Numéro de modèle : _______________________

Numéro de Série : _______________________

Vous trouverez ces numéros sur l’étiquette

apposée sur le côté du climatiseur.

En tant que partenaire d’ENERGY

STAR

®

, GE a déterminé que ce produit

était conforme aux exigences d’efficacité

énergétique d’ENERGY STAR

®

.

* Produits homologués E S

®

19

AEM10*

AEM12*

Au Canada, visitez-nous au :

www.electromenagersge.ca

Assistance à

la clientèle

Conseils de dépannage

Instructions

de montage

Entretien et nettoyage

Consignes d’utilisation

Consignes

de sécurité

20

IMPORTANTES CONSIGNES DE SÉCURITÉ.

VEUILLEZ LIRE TOUTES LES CONSIGNES AVANT UTILISATION.

AVERTISSEMENT !

Pour votre sécurité, les informations contenues dans ce manuel doivent être suivies afin de minimiser

les risques d’incendie, de chocs électriques ou de blessures corporelles.

nN’utilisez cet appareil qu’aux fins prévues

décrites dans le manuel d’utilisation.

nCe climatiseur doit être correctement

installé conformément aux Instructions

d’Installation avant toute utilisation.

nNe débranchez jamais votre climatiseur en

tirant sur le cordon d’alimentation. Prenez

toujours fermement la fiche en main et tirez

pour la sortir de la prise.

nRemplacez immédiatement tout cordon

électrique usé ou endommagé. Un

cordon d’alimentation endommagé doit

être remplacé par un nouveau cordon

d’alimentation obtenu du fabricant.

Ne réparez pas le cordon endommagé.

N’utilisez pas un cordon fissuré ou

présentant des dommages dus aux

frottements soit sur sa longueur ou aux

extrémités du côté de la fiche ou du

raccord.

nSi la prise de courant est d’un format

différent de la fiche, cette prise doit être

changée par un électricien qualifié.

n Eteignez votre climatiseur et débranchez-le

avant d’effectuer des réparations ou de le

nettoyer.

REMARQUE : Nous vous recommandons de faire

effectuer la maintenance par un technicien qualifié.

n Pour votre sécurité, ne stockez pas et

n’utilisez pas de matériaux combustibles,

d’essence ou d’autres vapeurs et liquides

inflammables dans les parages de cet

appareil ou de tout autre appareil.

n Tous les climatiseurs contiennent des

fluides frigorigènes qui, conformément, à la

législation fédérale doivent être retirés avant

la mise au rebut de l’appareil. Si vous mettez

au rebus un ancien appareil contenant des

fluides frigorigènes, vérifiez la procédure à

suivre auprès de la compagnie responsable

de l’élimination.

n Ces systèmes de climatisation R410A

demandent que les contracteurs et

les techniciens utilisent des outils, de

l’équipement et des mesures de sécurité

homologués pour une utilisation avec

frigorigène. N’UTILISEZ PAS un

équipement certifié pour fluide R22

refrigerant only.

CONSIGNES DE SÉCURITÉ

Ne coupez pas ou n’enlevez pas, sous aucun prétexte,

la troisième broche de mise à la terre du cordon

d’alimentation. Pour des raisons de sécurité, cet appareil

doit être correctement mis à la terre.

N’utilisez PAS d’adaptateur avec cet appareil.

Le cordon d’alimentation de cet appareil

est équipé d’une fiche à trois broches (pour

une mise à la terre) qui s’adapte à la prise

de courant standard à 3 broches (pour une

mise à la terre) pour minimiser les risques

de chocs électriques par cet appareil.

Le cordon d’alimentation est équipé d’un

dispositif d’interruption du courant. Un

bouton d’essai et de réenclenchement est

fourni sur le boîtier de la prise. Vous devez

tester le mécanisme régulièrement en

appuyant d’abord sur le bouton TEST (essai)

puis sur le bouton RESET (réenclenchement)

lorsque l’appareil est branché. Si le bouton

TEST (essai) ne bascule pas ou si le bouton

RESET (réenclenchement) ne reste pas

enclenché, cessez d’utiliser votre climatiseur

et appelez un technicien de service qualifié.

Faites vérifier la prise murale et le circuit

électrique par un électricien qualifié pour

s’assurer que le système est correctement

mis à la terre.

Dans le cas d’une prise biphasée,

l’installateur a la responsabilité et l’obligation

de la remplacer par une prise triphasée

correctement mise à la terre.

Le climatiseur doit toujours être branché

à sa propre prise électrique d’une tension

nominale correspondant à celle indiquée

sur sa plaque signalétique.

Ceci permet d’obtenir un meilleur rendement

du climatiseur et évite de surcharger les

circuits électriques du domicile qui risque

d’occasionner un incendie en surchauffant.

Consultez les Consignes d’Installations, dans

la section Exigences Electriques pour les exigences

de branchements électriques particuliers.

BRANCHEMENTS ÉLECTRIQUES

Consignes

de sécurité

Consignes d’utilisation

Entretien et nettoyage

Instructions

de montage

Conseils de dépannage

Assistance à

la clientèle

La page charge ...

GE AEM10AN Le manuel du propriétaire

Ce manuel convient également à

GE AEM10AN Le manuel du propriétaire

dans d''autres langues