Estate DU Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation
_rDis
{Plastic GiantTub lViodeis)
,LF
(modeies a tres 9rande cuve en piastique)
f
8573158
Table of Contents
Dishwasher Safety ................................. 2
Installation Requirements ........................... 3
Tools and parts ................................. 3
Location Requirements .......................... 3
Drain Requirements ............................. 5
VVater SuppHy Requirements ...................... 5
Electrical Requirements .......................... 5
Installation Instructions ............................. 6
Prepare cabinet opening
using existing utility hookups ..................... 6
Prepare cabinet opening
where there are no existing utility hookups .......... 7
Prepare dishwasher ............................. 9
Make electMcal connection ....................... 11
Connect to water supply ........................ 12
Connect to drain ............................... 13
Secure dishwasher in cabinet opening ............. 13
Dishwasher Safety
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completemy installed.
Do not push down on open door.
Doing so can resultinseriousinjuryor cuts.
You need to:
®SHowHy open dishwasher door while someone grasps the
rear of the dishwasher. Remove shipping materials, drain
hose and lower rack. Close dishwasher door until latched.
® Observe all governing codes and ordinances.
o Install this dishwasher as specified in these instructions.
o Installation should be performed by a qualified service
technician.The dishwasher must be installed to meet all
electrical and plumbing national and local codes and
ordinances.
/nsta//atien Requirements
TooJs and Parts
Gather the required tools and parts before starting
installation.
AH installations
Tools needed:
® pliers
PhHHps screwdriver
5/16" and 1/4" nut drivers
or hex sockets
® measuring tape or ruier
o 10" adjustaNe wrench that
opens to 1-1/8" (2.9 cm)
fiat-Made screwdriver
® utility knife
® 2 twist_on wire connectors
which are the proper size
to connect your househoH
wiring to 16ogauge wiring
in dishwasher
®flashlight
®shallow pan
o 5/8" open-end wrench
, bath towel
wood block
Parts needed:
90 ° elbow with 3/8" N.RT_
external threads on one
end. (The other end must
fit your water supply line.)
®Teflon _ tape or pipe joint
compound
shims (if installed with
built-up floor)
" small level
In addition, for new installations
Tools needed: Parts needed:
® electric drill with 1/2", 3/4"
and 1 1/2" hole saw bits
o small tubing cutter
o wire stripper
lq/2"-2" screwotype clamp
if connecting to waste-tee
®copper tubing (3/8"
recommended) or flexible
stainless steel braided fill
line
®clamp connector or
conduit connector to fit a
7/8" (2.2 cm) diameter hole
Parts supplied
A, 2 - drain hose clamps, 1 large and 1 small
B, 2 - # 10 x 1/2" Phillips-head screws
C, drain hose
B
Make sure all these parts are included.
See separate parts list for accessories available for your
dishwasher.
Location Requirements
Do not run drain lines, water lines or electrical wiring
where they can interfere with or contact dishwasher motor
or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor
should not touch the floor.
Do not install dishwasher over carpeted flooring.
Protect dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by
the warrant%
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part No. 4396277) is available
from your dealer for installing underneath the countertop,
but is not required.
Check location where dishwasher will be installed.The
location must provide:
o easy access to water, electricity and drain.
o convenient access for loading and unloading dishes.
Corner locations require a 2" (5.1 cm) minimum clearance
between the side of the dishwasher door and the wail or
cabinet.
o square opening for proper operation and appearance.
o cabinet front perpendicular to floor.
level floor. (If floor at front of opening is not level with
floor at rear of opening, shims may be needed to level
dishwasher.)
NOTE:To prevent shifting during dishwasher operation,
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it
winterized by authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Cutout dimensions" section.
HeIpfu_Tip: If the floor in the dishwasher opening is
uneven (example: tile flooring only partway into
opening) you will need to take special care in
measuring dimensions and in leveling dishwasher.
@Teflon is a registered trademark of E.I. Du Pont de Nemours and
Company
3
Product dimensions
3/4" (1.9 cm)
insulation -
may be
compressed
(not used on all
models)
_F--2B-1/4" (64.1 cm)_
II
24-!/2" (62.2 cm)
JIll 33-7/'8"
Jlt I Is6ore)mi_-,,
'H 'withWhT__j _elSremoved
21" (53.3 cm)
SiDE VIEW
23-7/8" (60.6 cm)
REAR ViEW
Cutout dimensions
24" (61 cm) _
All surfaces must be free
from intrusions
34 _l
(86.4 cm)
rnin.
24"
(61 cm)
rain.
9" 2"
(5,1 cm) 10"
1-3/4" 4-1/4' (25,4 cm)
(4,4 cm)$ (10,8 cm)$ clear areas
aire libre$
Cut holes in shaded area of cabinet walls or floor as specified below:
water line - 1/2" (!.3 crn)
drain line - 1-1/2" (3.8 cm)
direct wire - 3/4" (1.9 cm)
power supply cord - 1-1/2" (3.8 cm)
Measured from the lowest point on the underside of countertop. May be
reduced to 33-7/8" (86 cm) by removing wheels from dishwasher.
Minimum, measured from narrowest point of opening.
May be increased to 6-7/8" (175 cm) if height of opening is 34-1/2" (8_6 cm)
at its lowest point.
$ Both sides
Drain Requirements
o Use the new drain hose suppiied with your dishwasher.
iftMs is not iong enough, use a new drain hose with a
maximum iength of 12 feet (3.7 m) that meets aii
current AHAM/HAPMQ test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain
connector of the dishwasher.
Connect drain hose to waste tee or disposer iniet
above drain trap in house piumbing and 20" (50,8 cm)
minimum above the floor, it is recommended that the
drain hose either be iooped up and secureiy fastened
to the underside of the counter, or be connected to an
air gap_
air gap
o Use an air gap if the drain hose is connected to house
piumbing [ower than 20" (50,8 cm) above subfloor or
fioor,
o Use 1/2" minimum I.D. drain iine fittings.
Water SuppJy Requirements
A hot water line with 20-120 psi (138-862 kPa) water
pressure.
o 120OF (49oc) water at dishwasher.
o 3/8" Q.D. copper tubing with compression fitting or
flexible stainless steel braided fill line (1/2" minimum
plastic tubing is not recommended).
o A 90 ° elbow with 3/8" N.RT. external pipe threads on
one end.
Do not solder within 6" (15.2 cm) from water inlet valve.
EJectricaJ Requirements
Contact a qualified electrician.
Assure that the electrical installation is adequate and in
conformance with aii national and local codes and
ordinances.
You must have:
* 120_volt, 60 Hz, AC-only, 15 or 20 amp., fused electrical
supply.
o Copper wire only.
We recommend:
oA timeodelay fuse or circuit breaker.
* A separate circuit.
If direct wiring dishwasher:
o Use flexible, armored or non-metallic sheathed, copper
wire with grounding wire that meets the wiring
requirements for your home and local codes and
ordinances.
Use strain relief method provided with house wiring
junction box or install a U.L.qisted/CSA-certified clamp
connector to the house wiring junction box. if using
conduit, use a U.L.°listed/CSA-certified conduit connector.
_f connecting dishwasher with a power supply cord:
Use Power Supply Cord Kit (Part No. 4317824) marked for
use with dishwashers. Kit contents include:
-Volex, inc., UL listed 16 gauge 3 wire power supply
cord with 3 prong grounded plug.
- Neer C°500 7/8 inch strain relie£
- 3 wire connectors.
- Part No. 302797 grommet
Follow the kit instructions for installing the power
supply cord.
o Power supply cord must plug into a mating three prong,
grounded outlet, located in the cabinet next to the
dishwasher opening. Outlet must meet aii local codes and
ordinances.
Installation Instructions
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
1. Disconnect power,
2. Turn off water suppiy,
Prepare cabinet opening using
existing utility hookups
o Follow the steps in this section if you are installing the
dishwasher in an existing cabinet opening with utility
hookups.
o If you are installing the dishwasher in a cabinet opening
that does not have hookups, follow the steps under
"Prepare cabinet opening where there are no existing
utility hookups" section.
Check that the water
line reaches to the
front left of opening
where the water
connection will be
made.
Check that the direct
wire reaches to the
front right of opening
where the electrical
connection will be made.
6" (15.2 cm)
if the water line and the direct wire reach far enough into
the opening, proceed to the next section "install the drain
hose:' if they do not reach far enough, follow the steps
under "Prepare cabinet opening where there are no
existing utility hookups['
mnstaH the drain hose
IMPORTANT: Always use a new drain hose even when
installing a new replacement dishwasher.
1. Drill a 1-1/2" (&8 cm) diameter hole in cabinet wall or
floor on the side of the opening closest to the sink
J
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer- with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer- no air gap _
Option 4, No waste disposer- no air gap _
_an air gap is recommended
Helpfu_Tip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer = with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section}.
2. Attach drain hose to air gap with large spring-type
clamp. If the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw°type clampXL
3. Use a rubber hose connector _ with spring or screw_
type clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at
bast 20" (50.8 cm) above the floor where dishwasher
will be installed.
__ drain hose -
cut here if neededrubber hose
connector gap
spring or
screw-type large
J spring-type
clamp
"drain
hose
drain trap
4. Insert drain hose
through hole cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
Option 2, No waste disposer - with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with Harge spring-type
clamp. Jfthe drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm} screw-type champ×.
3. Use a rubber hose connectoW with spring or screw-
type cHamps x-to connect air gap to waste tee.
This connection must be before the drain trap and at
Heast 20" (50.8 cm) above the floor where dishwasher
wHHbe instaHHe&
drain hose -
cut here if needed
rubber hose
connector
air gap
large
spring4ype
drain
drain trap hose
Insert drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wHH be
made.
drain hose
Parts available from local plumbing supply stores
Option 3, Waste disposer - no air gap:
1. Remove the disposer knockout plug. Do not cut end of
drain hose.
Attach drain hose to disposer inHet with Harge spring-
type champ.
This connection must be before the drain trap and at
Heast 20" (50.8 cm) above the floor where dishwasher
will be installed. Htis recommended that the drain hose
be Hooped up and secureHy fastened to the underside of
the counter.
large spring-type
clamp
drain hose
disposer
inlet
drain trap
Insert drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wiHHbe
made.
drain hose
Option 4, No waste disposer - no air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section}.
2. Attach drain hose to waste tee with 1N/2" to 2"
(3.8 to 5 cm) screw-type clampS.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed. It is recommended that the drain hose
be looped up and securely fastened to the underside of
the counter.
drain hose -
cut here if needed
screw4ype clamp
tee
drain trap
3. Insert drain hose |
through hoHecut in
L
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
hose
Prepare cabinet opening where there
are no existing utiJit? hookups
Electrical connection
Option1, Direct wire method:
HelpfuITip: Wiring the dishwasher wiii be easier if you
route wire into the cabinet opening from the right side.
1. Drill a 3/4" (1.9 cm) optional preferred
hole in right-hand locations locations
cabinet side, rear or
floor. Preferred and
optional locations are
shown.
2. Wood cabinet: Sand
hoHe untiH smooth.
3.
4.
5.
MetaH cabinet: Cover
hoHe with grommet, not provided.
Run wire into house wiring junction box.
JnstaHHa U.L-Histed/CSA-certified champ connector
(strain reHief) for fHexibHe4ype wire. If instaHHing conduit,
attach a U.L.-Histed/CSA-certified conduit connector to
the junction box.
Run other end of wire
through cabinet hoHe.
CaMe must extend to the
right front of cabinet
opening.
Option2, Powersupplycord method:
NOTE: A mating, three prong, ground-type waii receptacie
is required in a cabinet next to the dishwasher opening.
1. DriHHa 1-1/2"
(3.8 cm) hoie in optional preferred
the cabinet rear locations locations
or side. Preferred
and optional
locations are
shown.
2. Wood cabinet:
Sand hob until
smooth.
Metal cabinet: Cover hole with grommet (Part No.
302797) inciuded with power suppiy cord kit.
Install the water line
HeJpfutTip: Routing the water line through the left side
of cabinet opening will make water connection easier.
Drill a minimum 1/2" (1.3 cm) hole in the cabinet side,
rear or floor. Preferred and optional locations are
shown.
preferred
locations
optional
locations
2. Measure overaii iength
of copper tubing
required.
3. Attach copper tubing
to the water iine with a
manuai shutoff vaive.
copper
tubing
'_iiiiiiiiiiiiL
SHowily feed copper
tubing through hoie in
cabinet. Copper tubing wiii bend and kink easiiy, so be
gentle.The copper tubing shouid be far enough into the
cabinet opening to connect it to dishwasher iniet on the
front Heft of the dishwasher.
Turn water shutoff vaive to "ON" position. Hush water
into a shaiiow pan to get rid of particies that may dog
the iniet vaive.
& Turn shutoff vaive to "OFF" position.
mnstaH the drain hose
IMPORTANT: Always use a new drain hose.
1. Drill a 1-1/2" (3,8 cm)
diameter hole in
cabinet wall or floor on
the side of the opening
closest to the sink
2. Connect drain hose to waste tee or waste disposer
using one of the following methods:
o Option 1, Waste disposer- with air gap
o Option 2, No waste disposer- with air gap
o Option 3, Waste disposer - no air gap _
Option 4, No waste disposer - no air gap _
"an air gap is recommended
HelpfulTip:To reduce the vibration of the hose, keep
the hose away from the floor and the edge of the hole
where it passes through the cabinet.
Option 1, Waste disposer = with air gap:
1. Remove the disposer knockout plug. Cut end of drain
hose if needed (do not cut ribbed section).
2. Attach drain hose to air gap with large spring-type
champ, if the drain hose was cut, use a 1-1/2" to 2"
(3.8 to 5 cm) screw4ype clamp×L
3. Use a rubber hose connector _ with spring or screw-
type clamps _ to connect air gap to disposer inlet.
This connection must be before the drain trap and at
least 20" (50.8 cm) above the floor where dishwasher
will be installed.
drain hose -
cut here if needed
rubber hose
connector
gap
large
J spring4ype
clamp
"drain
hose
drain trap
4. Insert drain hose
through hob cut in
cabinet to the front
center of opening where
drain connection will be
made.
drain hose
Parts available from local plumbing supply stores
Option 2, No waste disposer = with air gap:
1. Cut end of drain hose if needed (do not cut ribbed
section).
2. Attach drain hose to air gap with Harge spring-type
champ. If the drain hose was cut, use a 1+1/2" to 2"
(3.8 to 5 cm) screw-type cHamp×_
3. Use a rubber hose connector _ with spring or screw-
type damps +×+to connect air gap to waste tee_
This connection must be before the drain trap and at
Heast 20" (50.8 cm) above the floor where dishwasher
vvHHbe [nstaHHe&
drain hose -
cut here if needed
rubber hose
connector
large
spring4ype
drain
drain trap hose
Insert drain hose [ drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wHH be
made, / .....................
Parts available from local plumbing supply stores
Option 3, Waste disposer = no air gap:
1. Remove the disposer knockout pHug. Do not cut end of
drain hose.
Attach drain hose to disposer [nHet with Harge spring+
type champ,
This connection must be before the drain trap and at
Heast 20" (50,8 cm) above the floor where dishwasher
wiHHbe instaHHed. Htis recommended that the drain hose
be Hooped up and secureHy fastened to the underside of
the counter,
large spring-type
clamp
drain hose
disposer
inlet
drain trap
Hnsert drain hose
through hoHe cut in
cabinet to the front
center of opening where
drain connection wiHH be
made_
drain hose
Option 4, No waste disposer = no air gap:
1, Cut end of drain hose if needed (do not cut ribbed
section),
2, Attach drain hose to waste tee with 1+1/2" to 2"
(3,8 to 5 cm) screw+type ciamp_,
This connection must be before the drain trap and at
ieast 20" (50.8 cm) above the floor where dishwasher
wiii be instaiied, It is recommended that the drain hose
be iooped up and secureiy fastened to the underside of
the counter,
3. Insert drain hose /
through hoHecut in
cabinet to the front
center of opening where
drain connection wiHHbe
made_
drain hose
Parts available from local plumbing supply stores
Prepare dishwasher
Tip Over Hazard
Do not use dishwasher until completely installed,
Do not push down on open door,
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Grasp sides of dishwasher door frame and put
dishwasher on its back
3,
4.
Remove two screws attaching access panei and bwer
panei to dishwasher using a 1/4" hex socket, nut driver
or PMHips screwdriver.
Remove paneis and set paneis aside on a protective
surface.
Check that grounding chip is attached to the bvver
panel
lower
panel
clip
ApplyTeflon <_tape or pipe
joint compound to 90 ° elbow
fitting and connect fitting to
water inlet valve.
water inlet valve
I
Tighten elbow until snug, and
be sure that it faces to the
rear_
7. Remove terminal box cover.
- If you are direct wiring: install a U.L.-listed/CSAo
certified clamp connector to the terminal box. if using
conduit, use a U.h-listed/CSAocertified conduit
connector.
- If you are installing a power supply cord kit, do so
now, following kit instructions,
terminal
/ box cover
/
dishwasher wires
_ cable clamp
"[_ connector
He[pfu[Tip: Put cardboard under dishwasher until it is
installed in cabinet opening.The cardboard will help
protect floor covering during installation,
8,
Measure height of cabinet opening
from underside of countertop to
floor where dishwasher will be
installed (you need thelowest
point). Check chart for that height
opening. Put wheels in the required
position.
Number of
Minimum Wheel
turns olq
cutout height position front leg
34" (86.4 cm) 1 10
34-1/4" (87 cm) 2 5
34-I/2" (8:{6 cm) 3 0
9,
Turn both front leveler legs to the same
height.
If the minimum cutout height is less than
34" (86.4 cm), the rear wheels can be
removed for additional clearance.This will
allow the dishwasher to fit into a 33-7/8"
(86 cm) high cutout, but the dishwasher
will be more difficult to move into
position, if the wheels are removed, front leg
protect the floor when moving the dishwasher.
mfyou have built-up /countertop
floors
2,
Measure height of opening
from underside of
countertop to builtoup
floor_ if the laeiglat is at
least 33-3/4" (8&7 cm), the
dishwasher will fit into the
opening without
modification to the
countertop or flooring.
Put wheels in position 1
and turn the front leveler legs up aii the way.
3,
33-3/4"
(8&7 cm)
min.
Add shims as needed in the area shown to bring
dishwasher up to proper height.
NOTE: Shims must be securely attached to floor to
prevent their movement when the dishwasher is
operated.
lO
Check door spring tension
With another person hoiding the dishwasher to prevent it
from tipping, open and chose the door a few times, ffthe
door doses or falls open under its own weight, the door
tension wHi need to be adjusted.
• If the door doses too qubMy, decrease the spring
tension by moving the spring end toward the front of
the dishwasher.
• If the door fails open, increase the spring tension by
moving the spring end toward the back of the
dishwasher,
• Springs should be in the same notches on left and
right sides,
_, spring move
spring end
/
Move dishwasher into cabinet opening
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
1. Using two or more people, stand
the dishwasher up.
2. Grasp the sides of the dishwasher
at the edges of the door panel.
3. Tilt dishwasher backwards on
wheels and move dishwasher close
to cabinet opening. Do not push on
the front of the panel or on the
console--they may dent.
4. if dishwasher has a power supply cord, insert power
supply cord into hole cut into cabinet.
if using direct wire, check that it is on the right front
side of opening.
Check that water line is on the left side of opening and
drain hose is near the center of the hole in the cabinet.
5=
6.
Slowly move dishwasher completely into cabinet
opening. Do not kink or pinch copper tubing, drain
hose, power supply cord or direct wire between
dishwasher and cabinet.
HelpfuJTip: Once the dishwasher is in position, you
may have to support the front of the dishwasher by
raising, lowering or shimming front feet.
Remove cardboard from under dishwasher.
NOTE: it is all right if dishwasher fits tightly into cabinet
opening. Do not remove insulation blanket --the blanket
reduces the sound level.
LeveU the dishwasher
Align front of dishwasher door panel with cabinet
doors.You may need to adjust alignment to be even
with your cabinets.
HelpfuITip: Prop up one side of frame to hold
dishwasher up off floor when adjusting front legs.
With some installations, it may be easier to adjust the
front leg using the 3/16" hex head.
2. Check that leveling legs are firmly against the floor.
3. Close and latch the door, and place level against the
front panel. Check that dishwasher is plumb, if needed,
adjust leveling leg or add shims under rear wheel until
dishwasher is plumb.
¢-
/
1
4. Repeat for other side of dishwasher.
NOTE: Shims must be securely attached to floor to prevent
their movement when the dishwasher is operated.
5. Place level against top front
opening of tub. Check that
dishwasher is level from side to
side. If dishwasher is not level,
adjust front legs up or down until
dishwasher is level.
Make EJecttieaJ Connection
Check "Electrical requirements" section.
You need to:
®have the correct electrical supply and recommended
grounding method.
if you are:
o direct wiring, use Option 1
e using a power supply cord, use Option 2
Option 1, Direct wire method
1. Route direct wire so that it does not touch dishwasher
motor or lower part of dishwasher tub.
2. Pull direct wire through hole in terminal box.
11
3,
HeJpfu_ Tip:
Senect the proper size twist°on
connectors to connect your househoid __
wiring to 16-gauge dishwasher wiring,
o insert wire ends into twist°on
connector, Do not pre-twist bare wire,
®Twist connector,
o Gendy tug on wires to be sure both :_:_
are secured,
Connect the wires as follows using twist-on connectors
sized to connect direct wire to 16-gauge dishwasher
wire:
Power suppiy wire: Termina[ box wire:
wh it e-_-a_w hite
black-_:--}_ bhck
ground wire--ground connector
EmectricaJ Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminaJ box.
Do not use an extension cord.
Faimureto follow these instructions can result in death,
fire, or emectrical shock.
Form bare ground wire into a U-shaped hook, Wrap
ground wire hook clockwise around ground connector
and under the washer,
Securely tighten ground connector,
ground wire
washer
ground
connector
/
ground wire
6. Tighten clamp connector or
conduit connector screws,
screws
Reinstall terminal box cover with
wires inside terminal box.
The cover must be outside the box
on the left side.
8. Make sure no wires are pinched by cover.
Option 2, Power suppJy cord method
EmectricaJ Shock Hazard
PJug into a grounded 3 prong outmet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or emectricaJ shock.
1. Plug into a grounded 3 prong outlet,
2. Check that power supply cord does not touch
dishwasher motor or _ower part of dishwasher tub,
CoRRect to water suppny
Helpful Tip:
Compression fittings:
a, Slide nut onto copper tubing about 1" (2,5 cm),
b, Slide ferrule onto the tubing, Do not position ferrule
on the end of the tubing,
c, Put the tubing into the elbow as far as it will go,
d. Slide the nut and ferrule forward and start the nut
onto the elbow threads, Be gentle when handling
and positioning the copper tubing, it bends and kinks
easily,
nut
elbow._
1. To prevent vibration during operation, route the water
supply _ine so that it does not touch the dishwasher
base, frame or motor,
2. With copper tubing pushed into compression fitting as
far as it will go, use a wrench and tighten compression
fitting nut to elbow on water inlet valve, Do not use
Teflon ® tape with compression fittings,
3. Place paper towel under elbow, Turn on water supply
and check for leaks,
12
Connect to drain
1. To help minimize
vibration, route drain
hose to avoid contact
with motor, door spdngs,
water line, cabinet,
floodng or the edge of
the hole where it passes
through the cabinet,
2. Do not remove drain
loop from side of
dishwasher.
3=
4.
Place pan under end of drain hose. Pan will collect any
water in drain hose.
Place the smaller drain hose clamp onto the small end
of the drain hose.
hose clamp
/
5. Push the drain hose into the connector up to the stop
on the drain hose.
connector stop
6. Use pliers to open clamp and slide clamp onto
connector between stops on connector as shown.
hose clamp
,v/
stops
Secure dishwasher in cabinet opening
Tip Over Hazard
Do not use dishwasher until completely installed,
Do not push down on open door,
Doing so can resumt in serious injury or cuts.
1. If you have not already done so, open dishwasher door
and place towel over pump assembly and spray arm of
dishwasher.This will prevent screws from falling into
pump area when securing dishwasher to countertop.
2. Check that dishwasher is still level and centered side to
side in the opening.
3. Secure dishwasher to countertop with two, #10 x 1/2"
Phillips-head screws. The dishwasher must be secured
to keep it from tipping when door is opened. Do not
drop screws into bottom of dishwasher.
D
screw to countertop
4. Open door about 3 inches (7.6 cm) and check that space
between inner door and tub is equal on both sides. If
spacing is not equal, loosen bracket screws and shift
tub.Tighten bracket screws.
5. Check that top of door does not contact screws,
brackets, or countertop. If it does, dishwasher must be
lowered and reoleveled,
6. Remove towel from dishwasher.
7. Reinstall the lower dishrack.
13
Complete installation
1. Check that grounding chip is attached to the lower
panel
2. Hace the lower paneH behind the access panel Some
modeHs have insuHation on the access paneH which must
fallbehind the insuHation on the Hower panel
clip
3. HoH the two panels together and place them against
dishwasher leg.
4. Reinstall the screws through the holes in the access
panel and the slots in the lower panel, Install right side
screw first.
/ /
¢W
5,
6.
J
J
J
Check that the lower edge of the lower panel contacts
the floor,
Tighten the screws,
Direct wire method:
Electricam Shock Hazard
Emectricammy ground dishwasher.
Connect ground wire to green ground connector in
terminam box.
Do not use an extension cord,
Failure to fotmow these instructions can resumt in death,
fire, or electricam shock.
Power suppJy cord method:
Emectrical Shock Hazard
Plug into a grounded 3 prong outmet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these {nstructions can result in death,
fire, or emectrical shock.
7. Reconnect power or plug in dishwashen
Check operation
1,
2.
3.
4.
5,
6,
Read the Use and Care Guide that came with your
dishwasher,
Check that all parts have been installed and no steps
were skippe&
Check that you have all the tools you used,
Start dishwasher and allow it to complete the shortest
wash cycle, After the first two minutes, unlatch door,
wait five seconds, then open door,
Check to see that there is water in the bottom of the
dishwasher tub, Check that dishwasher is working
properly,
If not, disconnect power or unplug dishwasher and see
"If dishwasher does not operate" section,
14
mfdishwasher does not operate
First try the soHufions suggested here to possibHy avoid the
cost of a service call,
Has the circuit breaker tripped or the house fuse Mown?
Is the door dosed tightly and Hatched?
Has the cycle been set correctly to start the dishwasher?
Is the water turned on?
Hfnone of these work, call 1-800-253_1301,
or in Canada, call 1-800-807-6777,
For Roper modeHs, call 1o800-447-6737,
or in Canada, call 1-800-807-6777,
15
8573158 Printed in U.S.A.
(C2005 07/2005
Table des matieres
Securite du Jave-vaisseHe .......................... 17
Exigences d'instaHatJon ............................ 18
Outillage et pieces ............................. 18
Emplacement d'installaNon ...................... 18
Specifications de la canalisation d%vacuation ...... 20
Specifications de I'alimentation en eau ............ 20
Specifications electriques ....................... 20
Instructions dfnstallation .......................... 21
PreparaNon des ouvertures dans les placards -
uNHsaNon des modes de raccordement existants
pour canaHsaNons et c_bhge .................... 21
Preparation de I'emphcement dqnstaHaNon entre
les phcards brsque bs canaHsafions et c_bles
n'ont pas et6 instaH6s .......................... 22
Preparation du lave-vaisselle .................... 24
Raccordement eHectrique ........................ 27
Raccordement a la canalisation d'eau ............. 28
Raccordement a is canalisation d'evacuation ....... 28
Immobilisation du lave-vaisselle dans I'espace
d'installation .................................. 29
Securit#, du lave-vaissetle
Votre s_curit_ et celle des autres est tres importante.
Nous donnons de nombreux messages de securite importants darts ce manuel et sur votre appareil menager. Assurez-vous de
toujours lire tousles messages de securite et de vous y conformer.
Voici le symbole d'alerte de securite.
Ce symbole d'alerte de securite vous signale les dangers potentiels de deces et de blessures graves a vous
et & d'autres.
Tousles messages de securite suivront le symbole d'alerte de securite et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots signifient :
Risque possible de deces ou de blessure grave si vous ne
suivez pas immediatement les instructions.
Risque possible de deces ou de blessure grave si vous
ne suivez pas les instructions.
Tousles messages de securite vous diront quel est le danger potentiel et vous disent comment reduire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
Risque de basculement
Ne pas utiliser le lave-vaisseHe jusqu'a ce qu'il soit
cornpletement install_o
Ne pas appuyer sur la porte ouverteo
Le non-respect de ces instructions peut causer des
blessures graves ou des coupures,
Tenir compte de ceci :
o Ouvrir bntement Is porte du hve-vaisselb tandis qu'une
autre personne saisit I'arriere de I'appareil. Retirer bs
materiaux d'emballage, le tuyau de decharge et le panier
inferieur. Fermer la porte du lave-vaisselb et verrouiller le
Ioquet.
® Respecter les dispositions de tousles codes et reglements
en vigueur=
o Installer le lave-vaisselle conformement aux prescriptions
des presentes instructions.
® Linstallation devrait &tre execut6e par un technicien
qualifie, Veiller _ respecter les dispositions de tousles
codes et reglements Iocaux et nationaux regissant les
installations de plomberie et d'61ectricite,
17
Exigences d'instatlation
OutiHage et pieces
RassemMer tous bs oufiis et pieces necessaires avant de
commencer HnstaHafion.
Pour toutes les configurations d'installation
OutH[age necessaire
pince
tournevis Phillips
®tourneoecrou ou cHe
douHle - douHles
hexagonales 5/16" ou 1/4"
® metre-ruban ou regHe
o cHe a molette de 10"
(ouverture jusqu'& 2,9 cm
[1 1/8'I)
tournevis _ lame plate
®couteau utilitaire
o 2 connecteurs de fils de
taille appropriee pour le
raccordement des
conducteurs de I'appareil
(calibre 16) au c_blage de
la maison
o petit niveau
o lampe torche
plat peu profond
®cle plate 5/8"
o serviette de bain
®cale de bois
Pi_ces necessaires :
®raccord 90 ° avec filetage
externe de 3/8" NPT a une
extr6mite. (La configuration
de I'autre extr&mite doit
8tre adaptee a celle de la
canalisation d'arrivee
d'eau.}
ruban deTeflon_) ou
compose d%tancheit6 pour
tuyauteries
o cabs (pour I'installation
sur un plancher
rehaussement partiel}
Outillage et pieces supplernentaires pour
I'installation dans un local neuf
OutHJage necessaire :
perceuse electrique avec
scies a trous de 1/2", 3/4" et
1 1/2"
o petit coupe-tube
o pince a denuder
bride de tuyau a vis 1 1/2 -
2" pour raccordement a la
canalisation d%gout sur
un raccord T
Pieces fournies
Pieces n@cessaires :
®tube de cuivre (3/8"
recommande} ou conduit
de raccordement flexible
avec tresse d'acier
inoxydable
o serreoc_ble ou connecteur
de conduit utilisable sur
un trou de diametre 2,2
cm (7/8"}
A. 2 brides pour tuyau de decharge - 1 grosse, 1 petite
B. 2 vis Phillips n° 10 x 1/2"
C.Tuyau de decharge
A B
C
Verifier la presence de toutes ces pieces.
Voir la liste separ6e des pieces et accessoires disponibles
pour le lave-vaisselle.
@Teflonest une marque d_,pos6ede Du Pont de Nemours and Company.
18
EmpJacement d'instaHation
Ne pas placer canalisation d'evacuation, canalisation d'eau
ou cablage electrique a un endroit ou cela susciterait
interference ou contact avec les pieds ou le moteur du
lave-vaisselle.
A I'emplacement d'installation du laveovaisselle0 on doit
pouvoir etablir le degagement approprie entre le moteur et
le plancher. Le moteur ne doit pas toucher le plancher.
Ne pas installer le lave-vaisselle par_dessus un tapis.
Proteger du gel le lave°vaisselle et lea canalisations d'eau
qui I%limentent; la garantie de I'appareil ne couvre pas les
dommages imputables au gel.
Un ensemble "panneau lateral" est disponible chez les
revendeurs pour I'installation du laveovaisselle
I'extremite d'une rangee de placards.
Un accessoire pare-vapeur (produit n° 4396277} est
disponible chez les revendeurs pour I'installation de
I'appareil sous le plan de travail. Cependant I'utilisation de
cet accessoire n'est pas indispensable.
Inspecter I'emplacement d'installation du laveovaisselle; il
doit comporter les caracteristiques suivantes :
facilite d'acces aux canalisations d'eau et d'egout eta la
source d%lectricite.
acces facile pour chargement et dechargement de la
vaisselle. Dans le cas de I'installation dans un angle, on
doit pouvoir etablir un degagement de 5,1 cm (2"} ou plus
entre le c6te de la porte du lave-vaisselle et le tour ou le
placard.
ouverture carree offrant I'esthetique appropriee et
permettant un fonctionnement correct.
fagade des placards perpendiculaire au plancher.
plancher horizontal et plat (s'il y a un ecart de niveau
entre I'avant et I'arriere sur le plancher de I'emplacement
d'installation, il pourrait 6tre necessaire d'utiliser des
cales pour etablir I'aplomb de I'appareil}.
NOTE : Pour eviter tout deplacement des cabs durant le
fonctionnement de I'appareil, il eat necessaire de fixer lea
cabs au plancher.
Si le lave-vaisselle ne doit pas _tre utilise pendant une
periode prolongee ou s'il est laisse a un endroit qui
pourrait 6tre expose au gel, veiller a faire executer lea
operations de pre-hivernage par un technicien competent.
Veiller ace que les canalisations d'eau et d'evacuation et
les cables electriques soient dans la zone marquee en gris
dana la section "Dimensions de I'emplacement
d'installation'[
Conseil utile : Si le plancher de I'espace d'installation
n'est pas parfaitement horizontal et plat (exemple :
garnissage de carrelage sur une pattie seulement}, on
devra accorder une attention particuliere aux details
Iors du releve des dimensions, pour pouvoir etablir
I'aplomb correct du laveovaisselle.
Dimensions du produit
1,9 cm (3/4")
Le mat@iau
isolant (pas
utilise sur tous
les modeles)
pourra[t _tre
compr[me
64,1 crn(25-1/4")
JlJJ86cm/33-7/8"/
min., avec
roues enlevees
53,3 cm (21") ----_
VUE LATERALE
60,6 cm (23-7/8")--------:_*
VUE ARRIERE
Dimensions de Fespaee d'installation
\ 24"<61_,_n)
-- Toutes les surfaces doJvent
_tre exemptes de
protub@ances,
24"
(61 cm}
rain.
2"
(5,1 cm}1:
9" 2"
cm} (5,1 cm) 10"
1-3/4" 4-1/4 (25,4 cm)
(4,4 cm)$ (10,8 cm)$ zone d#,gagee$
Decouper les trous dans la zone marquee en gris du plancher, du rnur ou des
parois des placards, selon les specifications ci-dessous :
Canalisation d'eau - 1,3 cm (1/2")
Canalisation d'evacuation - 3,8 cm (1-I/2")
C_ble pour c_blage direct - 1,9 cm (3/4")
Cordon d'alimentation - 3,8 cm (I-1/2")
Mesure depuis le point le plus bas de la face [nf@ieure du plan de travail,
Cette dimension peut 6tre reduite a 86 cm (33-7/8") si on retire les roues
du lave-vaisselle.
_ Dimension minimale mesur6e au point le plus etroit de I'ouverture.
_ Cette dimension peut #tre portee a 17,5 cm (6-7/8") si la hauteur de
I'ouverture est de 34-I/2" (87,6 cm) au point le plus bas.
q: Des deux c6tes
19
Specifications de Ja canaJisation
o Ufiiiser Hetuyau d%vacuafion neuf fourni avec Helave-
vaisseHe. Si ce tuyau n'est pas suffisamment bng, utHiser
un tuyau d'evacuaNon neuf de bngueur maximab 3,7 m
(12 pi} qui saNsfait ies cdteres de Ha norme AHAM/HAPMO
en vigueur, resistant a Hachabur et aux detergents, et qui
pourra &tre connecte sur Heraccord de sortie de 2,5 cm
(1 "} du iave-vaisseHe.
o Connecter Ueconduit d%vacuafion _ Hacanaiisation
d%gout par Finterm&diaire d'un raccordT ou du raccord
d'un broyeur _ dechets situe plus haut que le siphon du
circuit de plomberie de la maison, eta au moins 50,8 cm
(20"} au-dessus du sol. On recommande de lover le tuyau
d%vacuation et de le fixer solidement sur la face
inf&rieure du plan de travail, ou de le raccorder _ un
dispositif brise-siphon.
brise-siphon
® Utiliser un dispositif brise-siphon si le tuyau d%vacuation
est connecte a la canalisation d'egout de la maison
moins de 50,8 cm (20"} au-dessus du sous-plancher ou du
plancher.
Utiliser un raccord de diametre interieur de 1/2" ou plus.
Specifications de J'aJimentation en eau
o Canalisation d'eau chaude, sous pression de 20 a 120
Ib/po 2(138-862 kPal.
®Temperature de 49°C (120°F) a I'entree du lave-vaisselle.
o Canalisation de cuivre de diametre externe 3/8" avec
raccord a compression, ou conduit de raccordement
flexible a tresse d'acier inoxydable (l%mploi d'un tube de
plastique de 1/2" minimum est possible, mais
deconseill6}.
raccord 90 ° avec filetage externe de 3/8" NPT _ une
extr6mite.
Ne pas executer de raccordement par soudure a moins de
15,2 cm (6"} de I%lectrovanne d'admission d'eau.
Specifications eJectriques
Contacter un electricien qualifie.
Verifier que I'installation electrique est adequate et qu'elle
satisfait les exigences de tousles codes et reglements
Iocaux et nationaux en vigueur.
Caracteristiques exigees :
120 volts CA, 60 Hz; protection par fusible 16 ou 20 A.
conducteurs de cuivre seulement
On recommande :
o un fusible temporise ou disjoncteur.
o une alimentation par un circuit independant.
Pour te taccordement direct du tave-vaisseHe :
o Utiliser un cable flexible blinde ou a gaine non
metallique, de conducteurs de cuivre, satisfaisant les
exigences des codes et reglements Iocaux.
oArrimer le cable avec le dispositif fourni sur la bo_te de
connexion de la maison, ou installer un serre-cable
(homologation UL ou CSA1 sur la bo_'te de connexion de
la maison. Dans le cas de I'emploi d'un conduit, utiliser
un connecteur de conduit (homologation UL ou CSA}.
AHmentation de J'appatei_ pat un cordon d'aJimentation :
Utiliser le cordon d'alimentation (produit n ° 4317824)
identifie pour I'utilisation avec un laveovaisselle.
L'ensemble comprend :
- cordon d'alimentation Volex inc., avec 3 conducteurs
de calibre 16 (homologation UL) et fiche de
branchement a 3 broches pour liaison a la terre.
- serreocable 7/8" Neer C-500
3 connecteurs de fils
hague de protection n ° 302797
Pour I'installation du cordon d%limentation, proceder
conformement aux instructions fournies avec
I'ensemble.
La fiche du cordon d'alimentation devra &tre branchee sur
une prise de courant a 3 alveoles de configuration
correspondante, reliee a la terre, installee dab le placard
c6te de I'emplacement d'installation du lave-vaisselle.
La prise de courant doit satisfaire les exigences de tous
les codes et reglements Iocaux.
2O
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
Estate DU Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation
dans d''autres langues
- English: Estate DU Installation guide
Documents connexes
Autres documents
-
Haier HDBC100AFS Installation Instructions Manual
-
KitchenAid 8573157 Manuel utilisateur
-
Whirlpool WDF518SAFW Guide d'installation
-
Kenmore 66517032402 Guide d'installation
-
Kenmore Elite 66516059402 Guide d'installation
-
IKEA IUD9750WS0 Guide d'installation
-
-
KitchenAid KUDU02FRBL0 Guide d'installation
-
Kenmore 66513862K601 Guide d'installation
-
Kenmore 66513749K602 Guide d'installation