Amana ADB1400AWB0 Guide d'installation

Marque: Amana

Modèle: ADB1400AWB0

Catégorie: Lave-vaisselle

Taper: Guide d'installation

iNSTALLATiON iNSTRUCTiONS

UNDERCOUNTER DISHWASHER

PLASTIC GIANT TUBMODELS

iNSTRUCTiONS D'INSTALLATION

LAVE-VAISSELLEENCASTRE

MODELES A TRESGRANDE CUVE EN PLASTIQUE

Table of Contents ................................................ 2

Table des mati_res .............................................. 21

W10282553A

Table of Contents

Dishwasher Safety ............................................2

InstallationRequirements .....................................3

Toolsand Parts...............................................3

Location Requirements .......................................3

Product and Cabinet Opening Dimensions .................... 4

Drain Requirements .......................................... 5

Water Supply Requirements .................................. 5

Electrical Requirements ...................................... 5

Installation Instructions ....................................... 6

Prepare Cabinet Opening--Existing Utilities .................... 6

Prepare Cabinet Opening--New Utilities ....................... 6

Prepare and Route Water Line ................................ 7

Install Drain Hose ............................................ 8

Installation Instructions (cont.)

Prepare Dishwasher ........................................ 10

Make Power Cord Electrical Connection ..................... 11

Determine Cabinet Opening ................................. 12

Choose Attachment Option ................................. 13

Move Dishwasher into Cabinet Opening ..................... 13

Connect to Water Supply .................................... 15

Connect to Drain ............................................ 16

Make Direct Wire Electrical Connection ...................... 16

Secure Dishwasher in Cabinet Opening ...................... 18

Complete Installation ....................................... 19

Check Operation ............................................ 20

If Dishwasher Does Not Operate ............................. 20

Additional Tips .............................................. 20

DISHWASHERSAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."

These words mean:

You can be killed or seriously injured if you don't immediately

follow instructions•

You can be killed or seriously injured if you don't follow

instructions•

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Tip Over Hazard

Do not use dishwasher until completely installed•

Do not push down on open door•

Doing so can result in serious injury or cuts•

You Need fo:

• Slowly open dishwasher door while someone grasps the rear of

the dishwasher. Remove shipping materials, drain hose and lower

rack. Close dishwasher door until latched.

• Observe all governing codes and ordinances.

• Install this dishwasher as specified in these instructions.

• Installation should be performed by a qualified service

technician. The dishwasher must be installed to meet all electrical

and plumbing national and local codes and ordinances.

iNSTALLATiON REQUIREMENTS

Tools and Parts

Gather the recommended tools and parts before starting

installation• Read and follow the instructions provided with any tools

listed here.

All Installations

Tools needed:

_,. Flat-blade

screwar!ver

•

5 _ 1

_6 and V4 _ UL histed/CSA _ n

nut drivers or _._Y" Approved twist-on U W

hex sockets i.y wire connectors* -- --

10 adjustable wrench s.,, ,, ..... ,4 _..-_

that opens to wrench _

11/8" (2.9 cm) _ .

*Must be the proper size to connect your household wiring to 16

gauge wiring in dishwasher

Other useful items you may need:

Flashlight _ Bath towel

Parts supplied:

Drainhos_C!amps(2)_rainhose #10x1¢

(! laige and I Small)I Phi!!ips-head

screws (2)Green

Make sure all these parts are included in the literature package.

Parts needed:

Compr x _ Hose Fatting

FOr part or kit, see local

retailer or call Whirlpool

Parts: 1-800-442.9991, Part

Number w10273460

Other parts you may also need:

11V£"_2,': : _ Sidem%unti_g kiWI Masking or_

(3811 z5cm) _ for solid surface duct tape I

screw_type I c°unter_°ps I I

I clamps (3 maximum)18212560)!_-art lyU.mDe r [ I

NOTE: Parts available for purchase in plumbing supply stores.

Check local codes. Check existing electrical supply. See "Electrical

Requirements" section. It is recommended that electrical connections be

made by a licensed electrical installer.

In addition, for first time installations

Tools needed:

Cordk

with W!, 3/41'

and 1Wi hole

saw bits

Parts needed:

Copper tubing (%" See '_Electrical Requirements" section

O.D.suggested) or i . .

flexible braided F0rD,rectVV!re: ForP0wer Supply

cater su.._.l, lin _ useUL Listed/ Cord: use UL

CSA Approved liste d power

_/f----__,_'_\ strain _elief SUPPLY cord kit

(,(.[t[.[L .)))))),)} to fit Y8 (2.2 cm)marked for use

hg!e W!!h d!shwasher

Location Requirements

Grounded electrical supply required.

Do not run drain lines, water lines or electrical wiring where

they can interfere with or contact dishwasher motor or legs.

The location where the dishwasher will be installed must

provide clearance between motor and flooring. Motor should not

touch the floor.

Do not install dishwasher over carpeted flooring.

Shelter dishwasher and water lines leading to dishwasher

against freezing. Damage from freezing is not covered by the

wa rra nty.

A side panel kit is available from your dealer for installing

your dishwasher at the end of your cabinetry.

A moisture barrier accessory (Part Number 4396277)is available

from your dealer for installing underneath the countertop.

Check location where dishwasher will be installed. The

location must provide:

• easy access to water, electricity and drain.

• Convenient access for loading and unloading dishes. Corner

locations require a 2" (5.1 cm) minimum clearance between the

side of the dishwasher door and the wall or cabinet.

• square opening for proper operation and appearance.

• cabinet front perpendicular to floor.

• level floor. (If floor at front of opening is not level with floor at

rear of opening, shims may be needed to level dishwasher.)

Helpful Tip: Be sure to accurately measure dimensions

and ensure dishwasher is level if the floor in the dishwasher

opening is uneven (example: flooring extends only partway into

opening).

NOTE: To avoid shifting during dishwasher operation.

shims must be securely attached to the floor.

If dishwasher will be left unused for a period of time or in a

location where it may be subject to freezing, have it winterized by

authorized service personnel.

Make sure pipes, wires and drain hose are within the

shaded area shown in the "Product and Cabinet

Opening Dimensions" section.

*Insulationmay

becompressed.

(notusedonallmodels)

NOTE:Shadedareaofcabinetwallsshowwhereutility

connectionsmaybeinstalled.

*MeasuredfromthelowestpointontheundersideOf

countertop.Maybereducedto33_(86cm)by

removingwheelsfromdishwasher.

"_Minimum,measuredfromnarrowestpointof

opening.

Check that all surfaces

have no protrusions that would

prohibit dishwasher installation.

Drain Requirements

A new drain hose is supplied with your dishwasher.

If the drain hose is not long enough, use a new drain hose with a

maximum length of 12' (3.7 m)(Part Number 3385556) that

meets all current AHAM/IAPMO test standards, is resistant to

heat and detergent, and fits the 1" (2.5 cm) drain connector of the

dishwasher.

Make sure to connect drain hose to waste tee or disposer inlet

above drain trap in house plumbing and 20" (50.8 cm) minimum

above the floor. It is recommended that the drain hose either be

looped up and securely fastened to the underside of the counter,

or be connected to an air gap.

Make sure to use an air gap if the drain hose is connected to

house plumbing lower than 20" (50.8 cm) above subfloor or floor.

Use 1/2"minimum I.D. drain line fittings.

If required, the air gap should be installed in accordance

with the air gap installation instructions. When connecting the air

gap, a rubber hose (not provided) will be needed to connect to the

waste tee or disposer inlet.

Water Supply Requirements

A hot water line with 20-120 psi (138-862 kPa) water

pressure can be verified by a licensed plumber.

120°F (49°C) water at dishwasher.

3/8"O.D. copper tubing with compression fitting or

flexible braided water supply line (Part Number 4396897RP)

NOTE: 1/2"minimum plastic tubing is not recommended.

A 90 ° elbow with 3/8"NET. external pipe threads on one

end.

Do not solder within 6" ( 15.2 cm) of the water inlet valve.

Electrical Requirements

Be sure that the electrical connection and wire size are adequate

and in conformance with the National Electrical Code, ANSI/NFPA

70 - latest edition and all local codes and ordinances.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA02169

You must have:

• 120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical

supply.

• copper wire only.

We recommend:

• a time-delay fuse or circuit breaker.

• a separate circuit.

if connecting dishwasher

with a power supply cord:

• Use UL listed power supply

cord kit (Part Number 4317824)

marked for use with dishwasher.

• Power supply cord must plug into

a grounded 3 prong outlet, located in the

cabinet next to the dishwasher opening.

Outlet must meet all local codes and

ordinances.

if connecting dishwasher with direct wiring:

•Use flexible, armored or

nonmetallic sheathed,

copper wire with

grounding wire that meets

the wiring requirements for your home and local codes and

ordinances.

• Use a UL Listed/CSA Approved strain relief.

iNSTALLATiON iNSTRUCTiONS

Electrical Shock Hazard

Disconnect electrical power at the fuse box or circuit

breaker box before installing dishwasher.

Failure to do so can result in death or electrical shock.

D"_conneCt electrical power at the fuSeboxor c!rcult-q

breaker b0x bef0re insta!!!ng dishwasher.

Yes'FollOw instructi0ns in the "PrePare cab!net

Opening_Existing utilities!! section_

NO'Follow instructions in the "Prepare Cabinet

Opening_New uti!ities'! secti0nl

_: E :isting hookups g t ity hookups

Water line

Prepare Cabinet OpeningmExisfing

Utilities

if the water line and the cable extend to the locations shown,

proceed to the "install Drain Hose" section. If they do not reach far

enough, follow the instructions in the "Prepare Cabinet Opening--

New Utilities" section.

Prepare Cabinet OpeningmNew

Utilities

Prepare and route the electrical supply

What type of electrical

connection will you use?

Direct Wire:

, _ _ Follow Option Binstructions

Option A, Power Supply Cord:

NOTE: A grounded 3 prong outlet is required inside a cabinet

next to the dishwasher cabinet opening.

Power Supply Cord-Drill hole

OptiSnal location

i ;

Drill a 11/2"(3.8 cm) hole in cabinet side or rear.

See product and cabinet opening dimensions.

Woodcabinet:Sandtheholeuntilsmooth.

Metalcabinet:Coverholewithgrommet(PartNumber302797)

includedwithpowersupplycordkit.

OptionB,Direct Wire:

Helpful Tip: Wiring the dishwasher will be easier if you route the

cable into the cabinet opening from the right-hand side.

Drill a 3/4'(1.9 cm) hole in right-hand cabinet side or rear.

See product and cabinet opening dimensions.

Wood cabinet: Sand the hole until smooth.

Metal cabinet: Cover hole with grommet (Part Number 302797

not included)

Route cable from power supply through cabinet hole (cable must

extend to the right front side of cabinet opening).

Tape cable to the floor in area shown. This will keep cable from

moving when dishwasher is moved into cabinet opening.

iiii_ii_i_iiiiii_ii_i1iiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiYiiiiiiiiiiiiiiiiiiiiiiiiii%ii_iiiiiii1iiiiiiiiiii_iiii_iiiiiiiiiiiii_iiii_iiii_iiiiiiiYiiiiiiiiiiiii1iiiiiiiiiii_iiii_iiii_iiii_iiii_iiiiiiiiiii_iiii_iiii_iiii_iiii_iiiiiii1i1ii1i1iiiiiii1i1ii1i1ii1i1ii1i1ii1i1ii1i1ii1i1iii_i¸iiiiii_i¸iii_iiii_iiii_i¸iii_i¸i¸i_iiiiiiiiiii_iiii_iiii_iiii_iiii_iiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiii_iiii_i

Prepare and Route Water Line

Helpful Tip: Routing the water line through the left side of

cabinet opening will make water connection easier.

Drill a 1/2"( 1.3 cm) hole in the cabinet side or rear.

Measure overall length of copper tubing or flexible braided

water supply line. Attach to the hot water line using a

connection configuration that is in compliance with local codes

and ordinances. The water line to the dishwasher should have a

manual shutoff valve.

Slowlyroutewatersupplylinethroughholeincabinet.(ifusing

coppertubing,itwillbendandkinkeasily,sobegentle.)It

shouldbefarenoughintothecabinetopeningtoconnectitto

thedishwasherinletonthefrontleftsideofthedishwasher.

4J Flush water supply line

Slowly turn water shutoff valve to "ON" position. Flush water

into a shallow pan until clear to get rid of particles that could

clog the inlet valve. Turn shutoff valve to "OFF" position.

Copper tubing only: Slide nut, then ferrule, about 1"

(2.5 cm) onto copper tubing.

NOTE: To avoid vibration during operation, route the

water supply line so that it does not touch the

dishwasher base, frame or motor.

JAdd 90° elbow fitting to the

water supply line

Connect the 3/8"compression fitting to the water supply

line prior to installing the unit into the cabinet opening.

Attach such that the 3/4"connection is facing upward.

Copper tubing only: Put the tubing into the 90° elbow

fitting as far as it will go (the copper tubing bends and

kinks easily). Slide the nut and ferrule forward and start

the nut onto the elbow threads.

Flexible braided connection: Secure nut to elbow using

s/8"open ended wrench or adjustable wrench.

NOTE: Do not use Teflon ®t tape with compression

fitti ngs.

Install Drain Hose

IMPORTANT: Always use a new drain hose. Check local codes

to determine whether an air gap is required.

If needed, drill a 11/2"(3.8 cm) diameter hole in cabinet wall or side

of the opening closest to the sink.

Route drain hose as shown through hole in cabinet to the front

center of opening where drain connection will be made. Tape

drain hose to the floor in area shown. This will keep the drain hose

from moving when dishwasher is moved into cabinet opening.

8 ¢ :TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

ConneCt drain hose to waste tee or waste disposer

using one Ofth e fo!!owing options:

* Option A; WaSte disp0ser _ no air gap

, Opti0n B_ No Waste disposer - no ai r gap

, Option C, Waste disposer - with air gap

i Option D, No waste disPoSer- With air gap

IMPORTANT: The drain hose connection of the disposer or a

waste tee must be made before the drain trap and at least 20"

(50.8 cm) above the floor where the dishwasher will be installed.

Helpful Tip: To reduce vibration of the hose, keep the hose away

from the floor.

Option A, Waste disposer - no air gap

1. Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Attach drain hose to disposer inlet with

large silver drain hose clamp (provided).

Use pliers to squeeze clamp open and

move into position.

Option B, No waste disposer - no air gap

1.Connect black end of of drain hose to waste

tee and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach black end of drain hose to waste tee

with a large silver drain hose clamp (provided).

Use pliers to squeeze clamp open and move

into position. Ifthe drain hose was cut, use a

1l&,,to 2" (3.8 to 5 cm) screw-type clamp (not

provided).

Option C, Waste disposer - with air gap

Drain trap

1.Using a hammer and screwdriver, knock

plug into disposer.

2. Use needle-nose pliers to remove plug.

3. Connect black end of drain hose to air gap

and cut if needed.

NOTE: Do not cut ribbed section.

Attach drain hose to air gap with large

silver drain hose clamp (provided). Use

pliers to squeeze clamp open and move

into position. If the drain hose was cut, use

a 11/2'' to 2" (3.8 to 5 cm) screw-type clamp

(not provided).

Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from air gap to disposer inlet.

Option D, No waste disposer - with air gap

1.Connect black end of drain hose to air gap

and cut if needed.

NOTE: Do not cut ribbed section.

2. Attach drain hose to air gap with large silver

drain hose clamp (provided). Use pliers to

squeeze clamp open and move into position.

If the drain hose was cut, use a 1W' to 2"

(3.8 to 5 cm) screw-type clamp (not

provided).

3. Use a rubber hose (not provided) with

screw-type clamps (not provided) to

connect from waste tee to air gap.

Tip Over Hazard

Do not use dishwasher until completely installed.

Do not push down on open door.

Doing so can result in serious injury or cuts.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using the precut slots in the insulation, fasten the insulation over the

molded hooks on the tub. Be sure to fasten the insulation down on

both sides of the tub.

Helpful Tip: Place cardboard under dishwasher until installed in

cabinet opening to avoid damaging floor covering. Do not use door

panel as a worktable without first covering with a towel to avoid

scratching the door panel.

Using two or more people, grasp sides of dishwasher door frame and

place dishwasher on its back.

Using a 1/4"hex head socket, nut driver or Phillips screwdriver,

remove the 2 screws attaching access panel and lower panel to

dishwasher.

NOTE: Do not remove tech sheet from access panel.

Using a 1/4"hex head socket, nut driver or Phillips screwdriver,

remove terminal box cover. Retain for later use.

Install a UL Listed/CSA Approved strain relief. Make sure

screwheads are facing to the left when tightening conduit nut.

Strain relief may be provided with the power supply cord kit.

If using Option B, proceed to "Determine Cabinet Opening," to

continue with the installation of your dishwasher.

Option A, Power Supply Cord:

Route cord so that it does not touch dishwasher motor to lower

part of dishwasher tub. Pull cord through strain relief in terminal

bow.

Select UL Listed/CSA Approved twist-on wire connectors rated to

connect your power supply cord to 16-gauge dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

Ground

wire

Remove the green grounding screw and place through the ring

terminal of the green ground wire. Reattach and tighten the

green screw.

NOTE: Do not pre-twist stranded wire. Twist on wire connector.

Gently tug on wires to be sure both are secured.

Connect wires black to black and white to white, using

UL Listed/CSA Approved twist-on wire connectors.

Ifneeded,seewebsiteforanimatedrepresentationofthisstep.

Visitwww.whirlpool.comunderFAQtab.

Tightenstrainreliefscrewstosecurecord.

Placewiresinsideterminalbox.Inserttabson

leftsideofcover.Makesurewiresaretuckedinsidebox.Close

coverensuringwiresarenotpinched.Use1/4"nutdriverand

previouslyremovedscrewtosecurecover.

NOTE:Donotplugintooutletuntilinstructed.

Determine Cabinet Opening

Measure height of cabinet opening from underside of

countertop to floor where dishwasher will be installed (you will

need to measure the lowest point on the underside of the

countertop and the highest point on the floor). Refer to

"Dishwasher Height Adjustment Chart" for wheel position and

the number of turns needed.

Dishwasher Height Adjustment

Cabinet I Wheel Number of turns

opening height position on front leg

33% (86.0cm) Removed All the way up

34 (86,4 cm) ! 1 . 10

34!/4'i (8710 cm)2

NOTE: If the minimum cabinet opening height is less than 34"

(86.4 cm), the rear wheels can be removed for additional

clearance. This will allow the dishwasher to fit into a 337/8"

(86 cm) high cabinet opening, but the dishwasher will be more

difficult to move. (Measurements are approximate. Wheels and

legs are preset at the factory for 341/2'' [87.6" crn].)

Adjust wheels and legs

Turn both leveler legs to the same height. Put wheels in the

required position determined from "Dishwasher Height

Adjustment Chart." (To change wheel position, use a flat-blade

screwdriver to pop out the wheel, then snap into the new

position.)

Built-upfloors(Kitchenfloorheightishigherthancabinet

opening.)Example:Kitchenfloortiledoesnotextendinto

cabinetopening.Addshimsasneededintheareashownto

bringthedishwasherupto34"(86.4cm)belowthecountertop.

NOTE:Shimsmustbesecurelyattachedtofloortoavoid

movementwhenthedishwasherisinuse.

Excessive Weight Hazard

Use two or more people to move and install

dishwasher.

Failure to do so can result in back or other injury.

Using two or more people, stand the dishwasher up.

IMPORTANT: The dishwasher must be secured to the

cabinet. There are two brackets, found in the parts bag,

attach the brackets to the top of the dishwasher if the

countertop if it is wood, laminate or another similar

surface. If your countertop is marble, granite or another

hard surface, install using Option #2.

Option 1, Countertop attachment

1. Remove the brackets from the package and place in the

open slots on the left and right-hand top of the

dishwasher collar as shown.

2. Insert the bracket into the slot on the collar. Using a

pair of pliers, bend the tab down to secure the bracket

in place. Repeat this step for the other side.

NOTE: Do not attach the dishwasher. This will be done

later.

Option 2, Dishwasher with Stainless Steel Tub Side

Attachment

(for marble, granite or other hard surface countertops)

1. Remove the brackets from the parts package.

2. Break off the end of the bracket along the scored line.

3. With another person holding the dishwasher to avoid it

from tipping, open dishwasher door, and place towel

over pump assembly and spray arm of dishwasher.

This will stop screws from falling into pump area when

securing dishwasher to cabinet.

4. Push the plastic buttons out of the side of the tub.

NOTE: Save the buttons to cover the holes after

dishwasher is installed.

5. Push bracket into slot on the side of dishwasher, and

bend tab in toward the side of the dishwasher so that it

keeps the bracket in place.

NOTE: Do not attach the dishwasher. This will be done

later.

Bend tab - side mount

Option 3, Dishwasher with Plastic Tub Side Attachment

(for marble, granite or other hard surface countertops)

Order Mounting Bracket Kit Part Number 8212560.

Move Dishwasher info Cabinef

Opening

11Stand dishwasher upright

Using two or more people, stand dishwasher upright.

NOTE: Do not install kickplate until instructed to do so.

IMPORTANT:Double-checkcorrectplacementofutilities.Grasp

thesidesofthedishwasherattheedgesofthedoorpanel.Tilt

dishwasherbackwardonwheelsandmovedishwashercloseto

cabinetopening.

NOTE:Donotpushonthefrontofthepanelorontheconsole-

theymaydent.

HelpfulTip:Temporarilytapeutilitiestothefloorinthe

locationsshowntokeepthemfrommovingwhendishwasheris

movedintothecabinetopening.

Checkthatwaterlineisontheleftsideofopening

anddrainhoseisnearthecenterofthecabinetopening.

Withanotherpersonholdingthedishwashertokeepitfrom

tipping,openandclosethedoorafewtimes.Ifthedoorcloses

orfallsopenunderitsownweight,thedoortensionwillneedto

beadjusted.

Ifthedoorclosestooquickly,decreasethespringtensionby

movingthespringendtowardthefrontofthedishwasher.

NOTE:Springsshouldbeinthesamenotchesonleftandright

sides.

Ifthedoorfallsopen,increasethespringtensionbymovingthe

springendtowardthebackofthedishwasher.

NOTE:Springsshouldbeinthesamenotchesonleftandright

sides.

7J Move dishwasher into

cabinet opening |:

Insulation _

blanket

IMPORTANT:Ifwheelswereremoved,coverthefloorwhen

movingthedishwashertoavoiddamagetothefloor.Slowly

movedishwashercompletelyintocabinetopening.Donotkinkor

pinchwaterline,drainhose,powersupplycordordirectwire

betweendishwasherandcabinet.Removecardboardfromunder

dishwasher.

NOTE:Itisallrightifdishwasherfitstightlyintocabinetopening.

Donotremoveinsulationblanket- theblanketreducesthe

soundlevel.

NOTE:Ifusingpowercord,makesuretorouteendthroughhole

incutoutbeforeslidingintocabinetopening.

Alignfrontofdishwasherdoorpanelwithfrontofcabinetdoors.

Youmayneedtoadjustalignmenttobeevenwithyour

cabinets.

Checkthatlevelinglegsarefirmlyagainstthefloor.

Closeandlatchthedoor,andplacelevelagainstthe

frontpanel.Checkthatdishwasheriscenteredfromfronttoback

intheopening.Ifneeded,adjustlevelingleguntildishwasheris

plumb.Repeatforothersideofdishwasher.

HeJpfuJTip:Pushuponfrontofdishwashertoraisedishwasher

offthegroundtoadjustfrontlegs.Withsomeinstallations,it

maybeeasiertoadjustthefrontlegusingthe3A6"hexhead

socketoradjustablewrench.

Placelevelagainsttopfrontopeningoftub.Check

thatdishwasherislevelfromsidetoside.Ifdishwasherisnot

level,adjustfrontlegsupordownuntildishwasherislevel.

Connect to Water Supply

Be sure rubber washer is properly seated in fitting. Slide the 3/4"

fitting up to the valve and hand tighten to avoid unintentional

cross-threading. Hand tighten until the coupling is tight. Using

pliers, check the tightness of the coupling. An additional 1/4to 1/2

turn may be required to seal the rubber gasket.

NOTE: Do not overtighten. Damage to the coupling can result.

Place paper towel under 90 ° elbow fitting. Turn on water

supply and check for leaks. If leak occurs, repeat previous step.

If needed, see website for animated representation

of this step. Visit www.whirlpool.com/watersupply under

FAQ tab.

NOTE: Do not use Teflon _>ttape with compression fittings.

1-_TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.

Connect to Drain

Green clamp

Black drain hose Drain hose

connector --

Drain hose stop

Stop

Place towel under drain hose to catch any water in drain hose.

Place the small green drain hose clamp onto the small end of

the drain hose. Push the new drain hose into the black drain

hose connector up to the drain hose stop.

Using pliers, squeeze open the small green drain hose clamp

and slide onto connector between stops.

Hose clamp final position

Black drain hose

connector --

Green clamp

Drain hose

Drain hose stop

Stop

Once connected, remove towel.

If needed, see website for animated representation of this step.

Visit www.whirlpool.com/drain under FAQ tab.

Make DirectWire Electrical

Connection

NOTE: If the power supply cord was connected earlier

proceed to "Secure Dishwasher in Cabinet Opening" section.

Option B, Direct Wire:

Route cable so that it does not touch dishwasher motor or

lower part of dishwasher tub. Pull cable through cable clamp in

terminal box.

Select UL listed or CSA approved twist-on wire connectors

(not included) rated to connect your household wiring to 16-gauge

dishwasher wiring.

Electrical Shock Hazard

Electrically ground dishwasher.

Connect ground wire to green ground connector

in terminal box.

Do not use an extension cord.

Failure to follow these instructions can result in

death, fire, or electrical shock.

171_:-t,I) 1,_-_11-- Ground

wire , you -

she

Ground

Form bare ground wire into a U-shaped hook. Wrap ground wire

hook clockwise around ground connector screw and under the

washer. Securely tighten ground connector.

NOTE: Do not pre-tvvist stranded wire. Twist on UL Listed/CSA

Approved wire connector. Gently tug on wires to be sure both

are secured.

Connect wires black to black and white to white, using UL

Listed/CSA Approved twist-on wire connectors (not included).

)

If needed, see website for animated representation

of this step. Visit www.whirlpool.oom/eleotrioal under FAQ

tab.

Tighten strain relief screws to secure cable.

Place wires inside terminal box. Insert tabs on left side of cover.

Make sure wires are tucked inside box. Close cover ensuring

wires are not pinched. Use 1/4"nut driver and previously

removed screw to secure cover.

Checkthatdishwasherisstilllevelfronttobackandsidetoside

incabinetopening.

IMPORTANT:IfyouhavesolidcountertopssuchasCorian_>t,

granite,etc.,youmustusesidemountingkit(PartNumber

8212560).Followkitinstructions.(Bracketsincludedwithkit.)

Opendishwasherdoor,removelowerdishrack,andplacetowel

overpumpassemblyandlowersprayarmofdishwasher.This

willkeepthescrewsfromfallingintopumpareawhenyouare

securingdishwashertocountertop.

NOTE:Donotdropscrewsintobottomofdishwasher.

Locatebracketsontopofdishwasherandsecuredishwasherto

countertopwithtwo,#10x1/2"Phillips-headscrews(included).

Thedishwashermustbesecuredtokeepitfromshiftingwhen

doorisopened.

Checkthattopofdoordoesnotcontactscrews,brackets,or

countertop.Ifitdoes,adjustlevelinglegs.

Opendoorandcheckthatspacebetweendishwashercabinet

openingandtubisequalonbothsides.Ifspacingisnotequal,

loosenbracketscrewssecuredandshifttub.Tightenbracket

screws.

1-"Corian is a registered trademark of E.I. Du Pont De Nemours and Company.

Removetowelfromdishwasher.Reinstallthelowerdishrack.

Ifneeded,seewebsiteforanimatedrepresentation

ofthisstep.Visitwww.whklpool.com/anchoringunderFAQ

tab.

Complete Installation

Check that grounding clip is attached to the lower panel.

Position the lower panel behind the access panel. On some

models there is insulation on the access panel which must

fall behind the insulation on the lower panel.

Hold the two panels together and place them against

dishwasher leg. Using a Phillips or 1A"screwdriver, reinstall

the screws through the holes in the access panel and the

slots in the lower panel,

Check that the lower edge of the lower panel contacts

the floor. Adjust if necessary.

Tighten access panel screws.

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong•

Do not use an adapter•

Do not use an extension cord•

Failure to follow these instructions can result

in death, fire, or electrical shock•

Plug into a grounded 3 prong outlet. Check that power supply

cord does not touch dishwasher motor or lower part of

dishwasher tub.

Reconnect Power

Check Operation

[_ Read the Dishwasher User instructions that came with your

dishwasher.

[_1 Check that all parts have been installed and no steps were

skipped. Check that you have all tools used.

C3Start dishwasher and allow it to complete the shortest wash

cycle. After the first 2 minutes unlatch door, wait 5 seconds,

then open door. Check to see that there is water in the

bottom of the dishwasher tub. Check that dishwasher is

working properly.

if dishwasher is not working properly, disconnect power or

unplug dishwasher and see "if Dishwasher Does Not

Operate" section.

• Has the circuit breaker tripped or the house fuse

blown?

• is the door closed tightly and latched?

• Has the cycle been set correctly to start the dishwasher?

• is the water turned on?

if none of these work, call 1-800-253-1301, or in Canada, call

1-800-807-6777.

For Roper models, call 1-800-447-6737, or in Canada call

1-800-807-6777.

Additional Tips

Expect longer wash times. Your new dishwasher will average 2

to 3 hours per load, but use nearly 40% less energy than older

models. Designed with a low wattage, low energy consumption

motor, your dishwasher washes longer to ensure exceptional

cleaning. Certain models are equipped with an optical water

sensor so the first cycle will run longer to calibrate to optical

sensor. Selecting certain options could increase cycle time past

3.5 hours.

Rinse Aid is necessary for good drying results:

This dishwasher is designed to be used with rinse aid for good

drying performance and controlling hard water deposit buildup.

Energy efficient dishwashers use less water and energy so they

depend on the water sheeting action of rinse aid for good

drying performance.

Start/Resume light may flash:

When pressing Start/Resume, you must make sure the door is

closed within 3 seconds. If you do not, the Start/Resume light

will flash until you press it again. (You must also do this when

adding a dish during the middle of a cycle.)

NOTE: If a braided supply hose is used, replace inlet hose after

5 years to reduce the risk of hose failure. Record hose installation

or replacement dates on the hose for future reference.

La page charge ...

Amana ADB1400AWB0 Guide d'installation

Marque: Amana

Modèle: ADB1400AWB0

Catégorie: Lave-vaisselle

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Amana ADB1400AWB0 Installation guide

Amana ADB1400AWB0 Guide d'installation

Amana ADB1400AWB0 Guide d'installation

dans d''autres langues

Documents connexes

Autres documents