Whirlpool DU1030XTXB2 Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation
®
iNSTALLATiON iNSTRUCTiONS
UNDERCOUNTER DISHWASHER
PLASTIC GIANT TUBMODELS
iNSTRUCTiONS D'INSTALLATION
LAVE-VAISSELLEENCASTRE
MODELES A TRESGRANDE CUVE EN PLASTIQUE
Table of Contents ................................................ 2
Table des mati_res .............................................. 21
W10282553A
Table of Contents
Dishwasher Safety ............................................2
InstallationRequirements .....................................3
Toolsand Parts...............................................3
Location Requirements .......................................3
Product and Cabinet Opening Dimensions .................... 4
Drain Requirements .......................................... 5
Water Supply Requirements .................................. 5
Electrical Requirements ...................................... 5
Installation Instructions ....................................... 6
Prepare Cabinet Opening--Existing Utilities .................... 6
Prepare Cabinet Opening--New Utilities ....................... 6
Prepare and Route Water Line ................................ 7
Install Drain Hose ............................................ 8
Installation Instructions (cont.)
Prepare Dishwasher ........................................ 10
Make Power Cord Electrical Connection ..................... 11
Determine Cabinet Opening ................................. 12
Choose Attachment Option ................................. 13
Move Dishwasher into Cabinet Opening ..................... 13
Connect to Water Supply .................................... 15
Connect to Drain ............................................ 16
Make Direct Wire Electrical Connection ...................... 16
Secure Dishwasher in Cabinet Opening ...................... 18
Complete Installation ....................................... 19
Check Operation ............................................ 20
If Dishwasher Does Not Operate ............................. 20
Additional Tips .............................................. 20
DISHWASHERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously injured if you don't immediately
follow instructions•
You can be killed or seriously injured if you don't follow
instructions•
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
Tip Over Hazard
Do not use dishwasher until completely installed•
Do not push down on open door•
Doing so can result in serious injury or cuts•
You Need fo:
• Slowly open dishwasher door while someone grasps the rear of
the dishwasher. Remove shipping materials, drain hose and lower
rack. Close dishwasher door until latched.
• Observe all governing codes and ordinances.
• Install this dishwasher as specified in these instructions.
• Installation should be performed by a qualified service
technician. The dishwasher must be installed to meet all electrical
and plumbing national and local codes and ordinances.
iNSTALLATiON REQUIREMENTS
Tools and Parts
Gather the recommended tools and parts before starting
installation• Read and follow the instructions provided with any tools
listed here.
All Installations
Tools needed:
_,. Flat-blade
screwar!ver
•
5 _ 1
_6 and V4 _ UL histed/CSA _ n
nut drivers or _._Y" Approved twist-on U W
hex sockets i.y wire connectors* -- --
10 adjustable wrench s.,, ,, ..... ,4 _..-_
that opens to wrench _
11/8" (2.9 cm) _ .
*Must be the proper size to connect your household wiring to 16
gauge wiring in dishwasher
Other useful items you may need:
Flashlight _ Bath towel
Parts supplied:
Drainhos_C!amps(2)_rainhose #10x1¢
(! laige and I Small)I Phi!!ips-head
screws (2)Green
Make sure all these parts are included in the literature package.
Parts needed:
Compr x _ Hose Fatting
FOr part or kit, see local
retailer or call Whirlpool
Parts: 1-800-442.9991, Part
Number w10273460
Other parts you may also need:
11V£"_2,': : _ Sidem%unti_g kiWI Masking or_
(3811 z5cm) _ for solid surface duct tape I
screw_type I c°unter_°ps I I
I clamps (3 maximum)18212560)!_-art lyU.mDe r [ I
NOTE: Parts available for purchase in plumbing supply stores.
Check local codes. Check existing electrical supply. See "Electrical
Requirements" section. It is recommended that electrical connections be
made by a licensed electrical installer.
In addition, for first time installations
Tools needed:
Cordk
with W!, 3/41'
and 1Wi hole
saw bits
Parts needed:
I
Copper tubing (%" See '_Electrical Requirements" section
O.D.suggested) or i . .
flexible braided F0rD,rectVV!re: ForP0wer Supply
cater su.._.l, lin _ useUL Listed/ Cord: use UL
CSA Approved liste d power
_/f----__,_'_\ strain _elief SUPPLY cord kit
(,(.[t[.[L .)))))),)} to fit Y8 (2.2 cm)marked for use
hg!e W!!h d!shwasher
Location Requirements
Grounded electrical supply required.
Do not run drain lines, water lines or electrical wiring where
they can interfere with or contact dishwasher motor or legs.
The location where the dishwasher will be installed must
provide clearance between motor and flooring. Motor should not
touch the floor.
Do not install dishwasher over carpeted flooring.
Shelter dishwasher and water lines leading to dishwasher
against freezing. Damage from freezing is not covered by the
wa rra nty.
A side panel kit is available from your dealer for installing
your dishwasher at the end of your cabinetry.
A moisture barrier accessory (Part Number 4396277)is available
from your dealer for installing underneath the countertop.
Check location where dishwasher will be installed. The
location must provide:
• easy access to water, electricity and drain.
• Convenient access for loading and unloading dishes. Corner
locations require a 2" (5.1 cm) minimum clearance between the
side of the dishwasher door and the wall or cabinet.
• square opening for proper operation and appearance.
• cabinet front perpendicular to floor.
• level floor. (If floor at front of opening is not level with floor at
rear of opening, shims may be needed to level dishwasher.)
Helpful Tip: Be sure to accurately measure dimensions
and ensure dishwasher is level if the floor in the dishwasher
opening is uneven (example: flooring extends only partway into
opening).
NOTE: To avoid shifting during dishwasher operation.
shims must be securely attached to the floor.
If dishwasher will be left unused for a period of time or in a
location where it may be subject to freezing, have it winterized by
authorized service personnel.
Make sure pipes, wires and drain hose are within the
shaded area shown in the "Product and Cabinet
Opening Dimensions" section.
*Insulationmay
becompressed.
(notusedonallmodels)
NOTE:Shadedareaofcabinetwallsshowwhereutility
connectionsmaybeinstalled.
*MeasuredfromthelowestpointontheundersideOf
countertop.Maybereducedto33_(86cm)by
removingwheelsfromdishwasher.
"_Minimum,measuredfromnarrowestpointof
opening.
Check that all surfaces
have no protrusions that would
prohibit dishwasher installation.
4
Drain Requirements
A new drain hose is supplied with your dishwasher.
If the drain hose is not long enough, use a new drain hose with a
maximum length of 12' (3.7 m)(Part Number 3385556) that
meets all current AHAM/IAPMO test standards, is resistant to
heat and detergent, and fits the 1" (2.5 cm) drain connector of the
dishwasher.
Make sure to connect drain hose to waste tee or disposer inlet
above drain trap in house plumbing and 20" (50.8 cm) minimum
above the floor. It is recommended that the drain hose either be
looped up and securely fastened to the underside of the counter,
or be connected to an air gap.
Make sure to use an air gap if the drain hose is connected to
house plumbing lower than 20" (50.8 cm) above subfloor or floor.
Use 1/2"minimum I.D. drain line fittings.
If required, the air gap should be installed in accordance
with the air gap installation instructions. When connecting the air
gap, a rubber hose (not provided) will be needed to connect to the
waste tee or disposer inlet.
Water Supply Requirements
A hot water line with 20-120 psi (138-862 kPa) water
pressure can be verified by a licensed plumber.
120°F (49°C) water at dishwasher.
3/8"O.D. copper tubing with compression fitting or
flexible braided water supply line (Part Number 4396897RP)
NOTE: 1/2"minimum plastic tubing is not recommended.
A 90 ° elbow with 3/8"NET. external pipe threads on one
end.
Do not solder within 6" ( 15.2 cm) of the water inlet valve.
Electrical Requirements
Be sure that the electrical connection and wire size are adequate
and in conformance with the National Electrical Code, ANSI/NFPA
70 - latest edition and all local codes and ordinances.
A copy of the above code standards can be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, MA02169
You must have:
• 120-volt, 60 Hz, AC-only, 15- or 20- amp, fused electrical
supply.
• copper wire only.
We recommend:
• a time-delay fuse or circuit breaker.
• a separate circuit.
if connecting dishwasher
with a power supply cord:
• Use UL listed power supply
cord kit (Part Number 4317824)
marked for use with dishwasher.
• Power supply cord must plug into
a grounded 3 prong outlet, located in the
cabinet next to the dishwasher opening.
Outlet must meet all local codes and
ordinances.
if connecting dishwasher with direct wiring:
•Use flexible, armored or
nonmetallic sheathed,
copper wire with
grounding wire that meets
the wiring requirements for your home and local codes and
ordinances.
• Use a UL Listed/CSA Approved strain relief.
iNSTALLATiON iNSTRUCTiONS
Electrical Shock Hazard
Disconnect electrical power at the fuse box or circuit
breaker box before installing dishwasher.
Failure to do so can result in death or electrical shock.
D"_conneCt electrical power at the fuSeboxor c!rcult-q
breaker b0x bef0re insta!!!ng dishwasher.
Yes'FollOw instructi0ns in the "PrePare cab!net
Opening_Existing utilities!! section_
NO'Follow instructions in the "Prepare Cabinet
Opening_New uti!ities'! secti0nl
_: E :isting hookups g t ity hookups
Water line
Prepare Cabinet OpeningmExisfing
Utilities
if the water line and the cable extend to the locations shown,
proceed to the "install Drain Hose" section. If they do not reach far
enough, follow the instructions in the "Prepare Cabinet Opening--
New Utilities" section.
Prepare Cabinet OpeningmNew
Utilities
Prepare and route the electrical supply
What type of electrical
connection will you use?
Direct Wire:
, _ _ Follow Option Binstructions
Option A, Power Supply Cord:
NOTE: A grounded 3 prong outlet is required inside a cabinet
next to the dishwasher cabinet opening.
Power Supply Cord-Drill hole
OptiSnal location
i ;
Drill a 11/2"(3.8 cm) hole in cabinet side or rear.
See product and cabinet opening dimensions.
Woodcabinet:Sandtheholeuntilsmooth.
Metalcabinet:Coverholewithgrommet(PartNumber302797)
includedwithpowersupplycordkit.
OptionB,Direct Wire:
Helpful Tip: Wiring the dishwasher will be easier if you route the
cable into the cabinet opening from the right-hand side.
Drill a 3/4'(1.9 cm) hole in right-hand cabinet side or rear.
See product and cabinet opening dimensions.
Wood cabinet: Sand the hole until smooth.
Metal cabinet: Cover hole with grommet (Part Number 302797
not included)
Route cable from power supply through cabinet hole (cable must
extend to the right front side of cabinet opening).
Tape cable to the floor in area shown. This will keep cable from
moving when dishwasher is moved into cabinet opening.
iiii_ii_i_iiiiii_ii_i1iiiiiiiiiiiiiiiiiiiiiiiiiiiii_iiiiiiiYiiiiiiiiiiiiiiiiiiiiiiiiii%ii_iiiiiii1iiiiiiiiiii_iiii_iiiiiiiiiiiii_iiii_iiii_iiiiiiiYiiiiiiiiiiiii1iiiiiiiiiii_iiii_iiii_iiii_iiii_iiiiiiiiiii_iiii_iiii_iiii_iiii_iiiiiii1i1ii1i1iiiiiii1i1ii1i1ii1i1ii1i1ii1i1ii1i1ii1i1iii_i¸iiiiii_i¸iii_iiii_iiii_i¸iii_i¸i¸i_iiiiiiiiiii_iiii_iiii_iiii_iiii_iiii_iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiiiiii1iiii_iiii_i
Prepare and Route Water Line
Helpful Tip: Routing the water line through the left side of
cabinet opening will make water connection easier.
Drill a 1/2"( 1.3 cm) hole in the cabinet side or rear.
Measure overall length of copper tubing or flexible braided
water supply line. Attach to the hot water line using a
connection configuration that is in compliance with local codes
and ordinances. The water line to the dishwasher should have a
manual shutoff valve.
7
Slowlyroutewatersupplylinethroughholeincabinet.(ifusing
coppertubing,itwillbendandkinkeasily,sobegentle.)It
shouldbefarenoughintothecabinetopeningtoconnectitto
thedishwasherinletonthefrontleftsideofthedishwasher.
4J Flush water supply line
Slowly turn water shutoff valve to "ON" position. Flush water
into a shallow pan until clear to get rid of particles that could
clog the inlet valve. Turn shutoff valve to "OFF" position.
Copper tubing only: Slide nut, then ferrule, about 1"
(2.5 cm) onto copper tubing.
NOTE: To avoid vibration during operation, route the
water supply line so that it does not touch the
dishwasher base, frame or motor.
JAdd 90° elbow fitting to the
water supply line
Connect the 3/8"compression fitting to the water supply
line prior to installing the unit into the cabinet opening.
Attach such that the 3/4"connection is facing upward.
Copper tubing only: Put the tubing into the 90° elbow
fitting as far as it will go (the copper tubing bends and
kinks easily). Slide the nut and ferrule forward and start
the nut onto the elbow threads.
Flexible braided connection: Secure nut to elbow using
s/8"open ended wrench or adjustable wrench.
NOTE: Do not use Teflon ®t tape with compression
fitti ngs.
Install Drain Hose
IMPORTANT: Always use a new drain hose. Check local codes
to determine whether an air gap is required.
If needed, drill a 11/2"(3.8 cm) diameter hole in cabinet wall or side
of the opening closest to the sink.
Route drain hose as shown through hole in cabinet to the front
center of opening where drain connection will be made. Tape
drain hose to the floor in area shown. This will keep the drain hose
from moving when dishwasher is moved into cabinet opening.
8 ¢ :TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
ConneCt drain hose to waste tee or waste disposer
using one Ofth e fo!!owing options:
* Option A; WaSte disp0ser _ no air gap
, Opti0n B_ No Waste disposer - no ai r gap
, Option C, Waste disposer - with air gap
i Option D, No waste disPoSer- With air gap
IMPORTANT: The drain hose connection of the disposer or a
waste tee must be made before the drain trap and at least 20"
(50.8 cm) above the floor where the dishwasher will be installed.
Helpful Tip: To reduce vibration of the hose, keep the hose away
from the floor.
Option A, Waste disposer - no air gap
1. Using a hammer and screwdriver, knock
plug into disposer.
2. Use needle-nose pliers to remove plug.
3. Attach drain hose to disposer inlet with
large silver drain hose clamp (provided).
Use pliers to squeeze clamp open and
move into position.
Option B, No waste disposer - no air gap
1.Connect black end of of drain hose to waste
tee and cut if needed.
NOTE: Do not cut ribbed section.
2. Attach black end of drain hose to waste tee
with a large silver drain hose clamp (provided).
Use pliers to squeeze clamp open and move
into position. Ifthe drain hose was cut, use a
1l&,,to 2" (3.8 to 5 cm) screw-type clamp (not
provided).
Option C, Waste disposer - with air gap
Drain trap
1.Using a hammer and screwdriver, knock
plug into disposer.
2. Use needle-nose pliers to remove plug.
3. Connect black end of drain hose to air gap
and cut if needed.
NOTE: Do not cut ribbed section.
4.
5,
Attach drain hose to air gap with large
silver drain hose clamp (provided). Use
pliers to squeeze clamp open and move
into position. If the drain hose was cut, use
a 11/2'' to 2" (3.8 to 5 cm) screw-type clamp
(not provided).
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from air gap to disposer inlet.
Option D, No waste disposer - with air gap
1.Connect black end of drain hose to air gap
and cut if needed.
NOTE: Do not cut ribbed section.
2. Attach drain hose to air gap with large silver
drain hose clamp (provided). Use pliers to
squeeze clamp open and move into position.
If the drain hose was cut, use a 1W' to 2"
(3.8 to 5 cm) screw-type clamp (not
provided).
3. Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
Tip Over Hazard
Do not use dishwasher until completely installed.
Do not push down on open door.
Doing so can result in serious injury or cuts.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using the precut slots in the insulation, fasten the insulation over the
molded hooks on the tub. Be sure to fasten the insulation down on
both sides of the tub.
Helpful Tip: Place cardboard under dishwasher until installed in
cabinet opening to avoid damaging floor covering. Do not use door
panel as a worktable without first covering with a towel to avoid
scratching the door panel.
Using two or more people, grasp sides of dishwasher door frame and
place dishwasher on its back.
10
Using a 1/4"hex head socket, nut driver or Phillips screwdriver,
remove the 2 screws attaching access panel and lower panel to
dishwasher.
NOTE: Do not remove tech sheet from access panel.
Using a 1/4"hex head socket, nut driver or Phillips screwdriver,
remove terminal box cover. Retain for later use.
Install a UL Listed/CSA Approved strain relief. Make sure
screwheads are facing to the left when tightening conduit nut.
Strain relief may be provided with the power supply cord kit.
J
If using Option B, proceed to "Determine Cabinet Opening," to
continue with the installation of your dishwasher.
Option A, Power Supply Cord:
Route cord so that it does not touch dishwasher motor to lower
part of dishwasher tub. Pull cord through strain relief in terminal
bow.
Select UL Listed/CSA Approved twist-on wire connectors rated to
connect your power supply cord to 16-gauge dishwasher wiring.
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
0
Ground
wire
Remove the green grounding screw and place through the ring
terminal of the green ground wire. Reattach and tighten the
green screw.
NOTE: Do not pre-twist stranded wire. Twist on wire connector.
Gently tug on wires to be sure both are secured.
Connect wires black to black and white to white, using
UL Listed/CSA Approved twist-on wire connectors.
11
Ifneeded,seewebsiteforanimatedrepresentationofthisstep.
Visitwww.whirlpool.comunderFAQtab.
Tightenstrainreliefscrewstosecurecord.
0
Placewiresinsideterminalbox.Inserttabson
leftsideofcover.Makesurewiresaretuckedinsidebox.Close
coverensuringwiresarenotpinched.Use1/4"nutdriverand
previouslyremovedscrewtosecurecover.
NOTE:Donotplugintooutletuntilinstructed.
Determine Cabinet Opening
Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed (you will
need to measure the lowest point on the underside of the
countertop and the highest point on the floor). Refer to
"Dishwasher Height Adjustment Chart" for wheel position and
the number of turns needed.
Dishwasher Height Adjustment
Cabinet I Wheel Number of turns
opening height position on front leg
I
33% (86.0cm) Removed All the way up
I
34 (86,4 cm) ! 1 . 10
34!/4'i (8710 cm)2
NOTE: If the minimum cabinet opening height is less than 34"
(86.4 cm), the rear wheels can be removed for additional
clearance. This will allow the dishwasher to fit into a 337/8"
(86 cm) high cabinet opening, but the dishwasher will be more
difficult to move. (Measurements are approximate. Wheels and
legs are preset at the factory for 341/2'' [87.6" crn].)
Adjust wheels and legs
Turn both leveler legs to the same height. Put wheels in the
required position determined from "Dishwasher Height
Adjustment Chart." (To change wheel position, use a flat-blade
screwdriver to pop out the wheel, then snap into the new
position.)
12
Built-upfloors(Kitchenfloorheightishigherthancabinet
opening.)Example:Kitchenfloortiledoesnotextendinto
cabinetopening.Addshimsasneededintheareashownto
bringthedishwasherupto34"(86.4cm)belowthecountertop.
NOTE:Shimsmustbesecurelyattachedtofloortoavoid
movementwhenthedishwasherisinuse.
Excessive Weight Hazard
Use two or more people to move and install
dishwasher.
Failure to do so can result in back or other injury.
Using two or more people, stand the dishwasher up.
IMPORTANT: The dishwasher must be secured to the
cabinet. There are two brackets, found in the parts bag,
attach the brackets to the top of the dishwasher if the
countertop if it is wood, laminate or another similar
surface. If your countertop is marble, granite or another
hard surface, install using Option #2.
Option 1, Countertop attachment
1. Remove the brackets from the package and place in the
open slots on the left and right-hand top of the
dishwasher collar as shown.
2. Insert the bracket into the slot on the collar. Using a
pair of pliers, bend the tab down to secure the bracket
in place. Repeat this step for the other side.
NOTE: Do not attach the dishwasher. This will be done
later.
Option 2, Dishwasher with Stainless Steel Tub Side
Attachment
(for marble, granite or other hard surface countertops)
1. Remove the brackets from the parts package.
2. Break off the end of the bracket along the scored line.
3. With another person holding the dishwasher to avoid it
from tipping, open dishwasher door, and place towel
over pump assembly and spray arm of dishwasher.
This will stop screws from falling into pump area when
securing dishwasher to cabinet.
4. Push the plastic buttons out of the side of the tub.
NOTE: Save the buttons to cover the holes after
dishwasher is installed.
5. Push bracket into slot on the side of dishwasher, and
bend tab in toward the side of the dishwasher so that it
keeps the bracket in place.
NOTE: Do not attach the dishwasher. This will be done
later.
Bend tab - side mount
Option 3, Dishwasher with Plastic Tub Side Attachment
(for marble, granite or other hard surface countertops)
Order Mounting Bracket Kit Part Number 8212560.
Move Dishwasher info Cabinef
Opening
11Stand dishwasher upright
Using two or more people, stand dishwasher upright.
NOTE: Do not install kickplate until instructed to do so.
13
IMPORTANT:Double-checkcorrectplacementofutilities.Grasp
thesidesofthedishwasherattheedgesofthedoorpanel.Tilt
dishwasherbackwardonwheelsandmovedishwashercloseto
cabinetopening.
NOTE:Donotpushonthefrontofthepanelorontheconsole-
theymaydent.
HelpfulTip:Temporarilytapeutilitiestothefloorinthe
locationsshowntokeepthemfrommovingwhendishwasheris
movedintothecabinetopening.
Checkthatwaterlineisontheleftsideofopening
anddrainhoseisnearthecenterofthecabinetopening.
Withanotherpersonholdingthedishwashertokeepitfrom
tipping,openandclosethedoorafewtimes.Ifthedoorcloses
orfallsopenunderitsownweight,thedoortensionwillneedto
beadjusted.
Ifthedoorclosestooquickly,decreasethespringtensionby
movingthespringendtowardthefrontofthedishwasher.
NOTE:Springsshouldbeinthesamenotchesonleftandright
sides.
Ifthedoorfallsopen,increasethespringtensionbymovingthe
springendtowardthebackofthedishwasher.
NOTE:Springsshouldbeinthesamenotchesonleftandright
sides.
7J Move dishwasher into
cabinet opening |:
Insulation _
blanket
14
IMPORTANT:Ifwheelswereremoved,coverthefloorwhen
movingthedishwashertoavoiddamagetothefloor.Slowly
movedishwashercompletelyintocabinetopening.Donotkinkor
pinchwaterline,drainhose,powersupplycordordirectwire
betweendishwasherandcabinet.Removecardboardfromunder
dishwasher.
NOTE:Itisallrightifdishwasherfitstightlyintocabinetopening.
Donotremoveinsulationblanket- theblanketreducesthe
soundlevel.
NOTE:Ifusingpowercord,makesuretorouteendthroughhole
incutoutbeforeslidingintocabinetopening.
Alignfrontofdishwasherdoorpanelwithfrontofcabinetdoors.
Youmayneedtoadjustalignmenttobeevenwithyour
cabinets.
Checkthatlevelinglegsarefirmlyagainstthefloor.
Closeandlatchthedoor,andplacelevelagainstthe
frontpanel.Checkthatdishwasheriscenteredfromfronttoback
intheopening.Ifneeded,adjustlevelingleguntildishwasheris
plumb.Repeatforothersideofdishwasher.
HeJpfuJTip:Pushuponfrontofdishwashertoraisedishwasher
offthegroundtoadjustfrontlegs.Withsomeinstallations,it
maybeeasiertoadjustthefrontlegusingthe3A6"hexhead
socketoradjustablewrench.
Placelevelagainsttopfrontopeningoftub.Check
thatdishwasherislevelfromsidetoside.Ifdishwasherisnot
level,adjustfrontlegsupordownuntildishwasherislevel.
Connect to Water Supply
Be sure rubber washer is properly seated in fitting. Slide the 3/4"
fitting up to the valve and hand tighten to avoid unintentional
cross-threading. Hand tighten until the coupling is tight. Using
pliers, check the tightness of the coupling. An additional 1/4to 1/2
turn may be required to seal the rubber gasket.
NOTE: Do not overtighten. Damage to the coupling can result.
Place paper towel under 90 ° elbow fitting. Turn on water
supply and check for leaks. If leak occurs, repeat previous step.
If needed, see website for animated representation
of this step. Visit www.whirlpool.com/watersupply under
FAQ tab.
NOTE: Do not use Teflon _>ttape with compression fittings.
1-_TEFLON is a registered trademark of E.I. Du Pont De Nemours and Company.
15
Connect to Drain
Green clamp
Black drain hose Drain hose
connector --
Drain hose stop
Stop
Place towel under drain hose to catch any water in drain hose.
Place the small green drain hose clamp onto the small end of
the drain hose. Push the new drain hose into the black drain
hose connector up to the drain hose stop.
Using pliers, squeeze open the small green drain hose clamp
and slide onto connector between stops.
Hose clamp final position
Black drain hose
connector --
Green clamp
Drain hose
Drain hose stop
Stop
Once connected, remove towel.
If needed, see website for animated representation of this step.
Visit www.whirlpool.com/drain under FAQ tab.
Make DirectWire Electrical
Connection
NOTE: If the power supply cord was connected earlier
proceed to "Secure Dishwasher in Cabinet Opening" section.
Option B, Direct Wire:
Route cable so that it does not touch dishwasher motor or
lower part of dishwasher tub. Pull cable through cable clamp in
terminal box.
Select UL listed or CSA approved twist-on wire connectors
(not included) rated to connect your household wiring to 16-gauge
dishwasher wiring.
16
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector
in terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in
death, fire, or electrical shock.
171_:-t,I) 1,_-_11-- Ground
wire , you -
she
Ground
Form bare ground wire into a U-shaped hook. Wrap ground wire
hook clockwise around ground connector screw and under the
washer. Securely tighten ground connector.
NOTE: Do not pre-tvvist stranded wire. Twist on UL Listed/CSA
Approved wire connector. Gently tug on wires to be sure both
are secured.
Connect wires black to black and white to white, using UL
Listed/CSA Approved twist-on wire connectors (not included).
)
If needed, see website for animated representation
of this step. Visit www.whirlpool.oom/eleotrioal under FAQ
tab.
Tighten strain relief screws to secure cable.
Place wires inside terminal box. Insert tabs on left side of cover.
Make sure wires are tucked inside box. Close cover ensuring
wires are not pinched. Use 1/4"nut driver and previously
removed screw to secure cover.
17
Checkthatdishwasherisstilllevelfronttobackandsidetoside
incabinetopening.
IMPORTANT:IfyouhavesolidcountertopssuchasCorian_>t,
granite,etc.,youmustusesidemountingkit(PartNumber
8212560).Followkitinstructions.(Bracketsincludedwithkit.)
Opendishwasherdoor,removelowerdishrack,andplacetowel
overpumpassemblyandlowersprayarmofdishwasher.This
willkeepthescrewsfromfallingintopumpareawhenyouare
securingdishwashertocountertop.
NOTE:Donotdropscrewsintobottomofdishwasher.
Locatebracketsontopofdishwasherandsecuredishwasherto
countertopwithtwo,#10x1/2"Phillips-headscrews(included).
Thedishwashermustbesecuredtokeepitfromshiftingwhen
doorisopened.
Checkthattopofdoordoesnotcontactscrews,brackets,or
countertop.Ifitdoes,adjustlevelinglegs.
Opendoorandcheckthatspacebetweendishwashercabinet
openingandtubisequalonbothsides.Ifspacingisnotequal,
loosenbracketscrewssecuredandshifttub.Tightenbracket
screws.
1-"Corian is a registered trademark of E.I. Du Pont De Nemours and Company.
18
Removetowelfromdishwasher.Reinstallthelowerdishrack.
Ifneeded,seewebsiteforanimatedrepresentation
ofthisstep.Visitwww.whklpool.com/anchoringunderFAQ
tab.
Complete Installation
Check that grounding clip is attached to the lower panel.
Position the lower panel behind the access panel. On some
models there is insulation on the access panel which must
fall behind the insulation on the lower panel.
Hold the two panels together and place them against
dishwasher leg. Using a Phillips or 1A"screwdriver, reinstall
the screws through the holes in the access panel and the
slots in the lower panel,
Check that the lower edge of the lower panel contacts
the floor. Adjust if necessary.
Tighten access panel screws.
19
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong•
Do not use an adapter•
Do not use an extension cord•
Failure to follow these instructions can result
in death, fire, or electrical shock•
Plug into a grounded 3 prong outlet. Check that power supply
cord does not touch dishwasher motor or lower part of
dishwasher tub.
Reconnect Power
Check Operation
[_ Read the Dishwasher User instructions that came with your
dishwasher.
[_1 Check that all parts have been installed and no steps were
skipped. Check that you have all tools used.
C3Start dishwasher and allow it to complete the shortest wash
cycle. After the first 2 minutes unlatch door, wait 5 seconds,
then open door. Check to see that there is water in the
bottom of the dishwasher tub. Check that dishwasher is
working properly.
if dishwasher is not working properly, disconnect power or
unplug dishwasher and see "if Dishwasher Does Not
Operate" section.
• Has the circuit breaker tripped or the house fuse
blown?
• is the door closed tightly and latched?
• Has the cycle been set correctly to start the dishwasher?
• is the water turned on?
if none of these work, call 1-800-253-1301, or in Canada, call
1-800-807-6777.
For Roper models, call 1-800-447-6737, or in Canada call
1-800-807-6777.
Additional Tips
Expect longer wash times. Your new dishwasher will average 2
to 3 hours per load, but use nearly 40% less energy than older
models. Designed with a low wattage, low energy consumption
motor, your dishwasher washes longer to ensure exceptional
cleaning. Certain models are equipped with an optical water
sensor so the first cycle will run longer to calibrate to optical
sensor. Selecting certain options could increase cycle time past
3.5 hours.
Rinse Aid is necessary for good drying results:
This dishwasher is designed to be used with rinse aid for good
drying performance and controlling hard water deposit buildup.
Energy efficient dishwashers use less water and energy so they
depend on the water sheeting action of rinse aid for good
drying performance.
Start/Resume light may flash:
When pressing Start/Resume, you must make sure the door is
closed within 3 seconds. If you do not, the Start/Resume light
will flash until you press it again. (You must also do this when
adding a dish during the middle of a cycle.)
NOTE: If a braided supply hose is used, replace inlet hose after
5 years to reduce the risk of hose failure. Record hose installation
or replacement dates on the hose for future reference.
20
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Whirlpool DU1030XTXB2 Guide d'installation
- Catégorie
- Lave-vaisselle
- Taper
- Guide d'installation