JVC GZ-R460 Mode d'emploi

Basic User Guide

HD MEMORY CAMERA

GZ-R460A

B5A-2475-00

BC mark means complies with Energy Efficiency Law.

BC

EN

.

Detailed User Guide

For more details on operating this

product, please refer to the “Detailed

User Guide” at the following website.

o

http://manual3.jvckenwood.com/index.html/

.

Mobile User Guide

When you are outside, refer to

the “Mobile User Guide”.

Mobile User Guide can be

viewed with standard browser

for Android tablet and iPhone.

o

http://manual3.jvckenwood.com/mobile/us/

Dear Customers

Thank you for purchasing this JVC product.

Before use, please read the Safety

Precautions and Cautions on p. 2 and

p. 16 to ensure safe use of this product.

For Future Reference:

Enter the Model No. (located on the bottom

of the camera) and Serial No.

(located on the bottom of the camera)

below.

Model No.

Serial No.

Safety Precautions

.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead

symbol, within an equilateral

triangle, is intended to alert the

user to the presence of uninsulated

"dangerous voltage" within the

product's enclosure that may be of sufficient

magnitude to constitute a risk of electric shock

to persons.

The exclamation point within an

equilateral triangle is intended to

alert the user to the presence of

important operating and

maintenance (servicing)

instructions in the literature accompanying the

appliance.

For AC adapter only:

WARNING: TO REDUCE THE RISK OF

FIRE OR ELECTRIC SHOCK, DO NOT

EXPOSE THE AC ADAPTER TO RAIN

OR MOISTURE.

0

Do not charge camcorder in area

exposed to rain or moisture.

NOTES:

0

The rating plate and safety caution are on

the bottom and/or the back of the main unit.

0

The serial number plate is on the bottom of

the main unit.

0

The rating information and safety caution of

the AC adapter are on its upper and/or lower

sides.

WARNING:

The camcorder with battery installed should

not be exposed to excessive heat such as

direct sunlight, fire or the like.

CAUTION:

A built-in lithium-ion battery is inside the unit.

When discarding the unit, environmental

problems must be considered and the local

rules or laws governing the disposal of these

batteries must be followed strictly.

Do not point the lens directly into the sun. This

can cause eye injuries, as well as lead to the

malfunctioning of internal circuitry. There is

also a risk of fire or electric shock.

CAUTION!

The following notes concern possible

physical damage to this unit and to the user.

Carrying or holding this unit by the LCD

monitor can result in dropping the unit, or in

a malfunction.

Do not use a tripod on unsteady or unlevel

surfaces. It could tip over, causing serious

damage to the unit.

CAUTION!

Connecting cables (Audio/Video, etc.) to this

unit and leaving it on top of the TV is not

recommended, as tripping on the cables will

cause this unit to fall, resulting in damage.

CAUTION:

The mains plug shall remain readily

operable.

0

Remove the mains plug immediately if the

camcorder functions abnormally.

2 EN

Make a backup of important recorded

data

JVC will not be responsible for any lost data.

It is recommended to copy your important

recorded data to a disc or other recording

media for storage once every 3 months.

IMPORTANT SAFETY INSTRUCTIONS

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Clean only with dry cloth.

6.

Do not block any ventilation openings.

Install in accordance with the

manufacturer’s instructions.

7.

Do not install near any heat sources such

as radiators, heat registers, stoves, or other

apparatus (including amplifiers) that

produce heat.

8.

Protect the power cord from being walked

on or pinched particularly at plugs,

convenience receptacles, and the point

where they exit from the apparatus.

9.

Only use attachments/accessories

specified by the manufacturer.

.

10.

Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or

sold with the apparatus. When a cart is used,

use caution when moving the cart/

apparatus combination to avoid injury from

tip-over.

11.

Unplug this apparatus during lightning

storms or when unused for long periods of

time.

When using the AC adapter in areas

other than the USA

The provided AC adapter features automatic

voltage selection in the AC range from 110 V

to 240 V.

USING HOUSEHOLD AC PLUG ADAPTER

In case of connecting the unit’s power cord

to an AC wall outlet other than American

National Standard C73 series type use an AC

plug adapter, called a “Siemens Plug”, as

shown. For this AC plug adapter, consult your

nearest JVC dealer.

.

Plug Adapter

0

Remove the AC adapter from the AC wall

outlet when not in use.

0

Do not leave dust or metal objects adhered

to the AC wall outlet or AC adapter (power/

DC plug).

0

Be sure to use the supplied AC adapter.

0

Do not use the supplied AC adapter with

other devices.

If this symbol is shown, it is

only valid in the European

Union.

This product is licensed under the AVC

Patent Portfolio License for the personal use

of a consumer or other uses in which it does

not receive remuneration to (i) encode video

in compliance with the AVC standard (“AVC

Video”) and/or (ii) decode AVC Video that

was encoded by a consumer engaged in a

personal activity and/or was obtained from a

video provider licensed to provide AVC

Video. No license is granted or shall be

implied for any other use.

Additional information may be obtained from

MPEG LA, L.L.C.

See http://www.mpegla.com

EN 3

Remember that this unit is intended for

private consumer use only.

Any commercial use without proper

permission is prohibited. (Even if you record

an event such as a show, performance or

exhibition for personal enjoyment, it is

strongly recommended that you obtain

permission beforehand.)

Trademarks

0

AVCHD and AVCHD logo are trademarks of

Panasonic Corporation and Sony

Corporation.

0

The terms HDMI and

HDMI High-Definition

Multimedia Interface,

and the HDMI Logo are trademarks or

registered trademarks of HDMI Licensing

Administrator, Inc. in the United States and

other countries.

0

Manufactured under license from Dolby

Laboratories. Dolby, Dolby Audio and the

double-D symbol are trademarks of Dolby

Laboratories.

0

SDXC logo is a trademark of SD-3C LLC.

0

Windows® is either registered trademark or

trademark of Microsoft Corporation in the

United States and/or other countries.

0

Apple, Mac, Mac OS, OS X, iMovie, iPhoto,

iPhone and Safari are trademarks of Apple

Inc., registered in the U.S. and other

countries.

0

Intel and Intel Core are trademarks or

registered trademarks of Intel Corporation

or its subsidiaries in the United States and

other countries.

0

Google™, Android™, YouTube™,

YouTube logo and Chrome™ are

trademarks and/or registered trademarks of

Google Inc.

0

QR Code is a registered trademark of Denso

Wave Incorporated.

0

Other product and company names

included in this instruction manual are

trademarks and/or registered trademarks of

their respective holders.

0

Marks such as ™ and ® have been omitted

in this manual.

.

This unit is equipped with Water

proof, Dust proof, Drop proof and

Freeze proof.

Water proof: Equivalent to IEC

Standard publication 529 IPX8

and IPX6 (1 hour at depths up to

5 m (16.4 ft))

Dust proof: Equivalent to IEC

Standard publication 529 IP5X

Drop proof: This camera clears

company testing compliant with

"MIL-STD-810F Method; 516.5

Shock: dropping onto plywood

3cm (1-3/16") thick from a height

of 1.5 m (4.9 ft)"

Freeze proof: Allowable

operating temperatures: −10°C

to +40°C (14°F to 104°F)

Note: Temperatures between

−10°C and 0°C (14°F and 32°F)

temporarily lower battery

performance, reducing the time

available for recording.

Precautions for waterproof function

0

Malfunction due to misuse by the

customer is not covered by warranty.

0

Before use in water, be sure to read and

understand the “Detailed User Guide”.

0

Close the terminal cover firmly until it

clicks and confirm that the red sign

completely goes off.

0

Make sure that there is no damage to and

no foreign material adhered to the

packing inside the cover.

0

Use the camcorder in marine water and

fresh water not deeper than 5 m or for not

more than 1 hour.

0

The waterproof cannot be guaranteed if

the camcorder is subject to impact such

as dropping.

0

Do not jump or dive into water holding the

camcorder.

0

Do not use the camcorder in strong water

flows such as in rapids or under

waterfalls. The strong water pressure

may impair the waterproof performance.

0

Do not soak the camcorder in hot springs

or water of 40°C or higher.

4 EN

Fogging inside the Lens

Models with waterproof function are airtight.

When the temperature rises during

recording, condensation can occur inside

the lens due to the internal humidity.

During recording

To prevent the temperature of this unit from

rising, we recommend that you use the unit

in the following ways.

A

Avoid frequent exposure to direct

sunlight.

Record under the shade or use an

umbrella. Best if you could keep a wet

towel cover the unit.

B

The use of a tripod is recommended.

Long hours of recording while holding the

unit in your hands will cause the

temperature of the unit to rise.

C

It is better to leave the terminal cover open

while recording.

However, the waterproof, dust-proof and

shockproof features do not function in this

condition. Do take note of the environment

when using the camera. (Do not use a wet

towel.)

D

Make sure to turn off the power when you

are not recording.

The power turns off when the LCD monitor

is closed.

During charging

It is recommended to charge the unit in a low

humidity environment.

The moist air inside the unit can cause

condensation.

We recommend that you charge the unit in a

room where humidifier is not in use, and in

an air-conditioned room during summer.

When fogging occurs inside the lens

Open the terminal cover to reduce the

temperature, close the LCD monitor and

leave the camera as it is for a while.

.

Open the terminal cover.

Protecting the Lens

There is a protective glass in front of the lens

to protect the lens.

0

If the protective glass is dirty, wipe clean

using a commercially available cleaning

cloth.

.

Lens protective glass

EN 5

Contents

Safety Precautions .......................................................................................................... 2

Verifying the Accessories ............................................................................................... 7

Grip Belt Adjustment ....................................................................................................... 8

Date and Time Setting

.................................................................................................... 8

Open the terminal cover (SD card cover) ........................................................................ 9

Getting Started

Charging the Battery ..................................................................................................... 10

Inserting an SD Card .................................................................................................... 11

Recording

Video Recording ........................................................................................................... 12

Playback

Playing Back/Deleting Files on this Unit

........................................................................ 14

Copying

Install Everio MediaBrowser (Windows 10)

................................................................................... 15

Further Information

Troubleshooting/Cautions ............................................................................................. 16

Recordable Time/Specifications ................................................................................... 20

6 EN

Verifying the Accessories

AC Adapter

AC-V11U

Adapter Cable

QAM1580-001

USB Cable

(Type A - Micro Type

B)

AV Cable

E3A-0085-00

.

Lens Cap

Core Filter

(for AV Cable)

Basic User Guide

(this manual)

.

0

Please

consult your JVC dealer or the nearest JVC service center when purchasing

a new AV cable.

0

Attach the lens cap when carrying the camera around and when the camera is not

in use.

EN 7

Grip Belt Adjustment

.

Open the belt

Adjust the length of the belt

Fasten the belt

Date and Time Setting

1

Open the LCD monitor.

0

The unit turns on. When the LCD

monitor is closed, the unit turns off.

2

Tap [OK] when [SET DATE/

TIME!] is displayed.

.

SET DATE/TIME!

OK

3

Set the date and time.

.

201824 10 00

DEC

TIME

DATE

SAVE

DATE & TIME

0

When

the month, day, year, hour, or

minute item is tapped, 3 and 2 will

be displayed.

Tap 3 or 2 to adjust the value.

0

Repeat this step to input the month,

day, year, hour, and minute.

4

After setting the date and

time, tap [SAVE].

5

Select the region where you

live and tap [SAVE].

0

Time difference between the

selected city and the GMT

(Greenwich Mean Time) is

displayed.

0

Tap 0 or 1 to select the city name.

.

GMT

SAVE

DATE & TIME/AREA

8 EN

Open the terminal cover (SD card cover)

A

Open the LCD monitor.

B

Slide down the terminal cover

lock and slide the cover aside

C

Lift the cover slowly.

o

To close

.

Not properly closed if the red mark is visible!

Leave the LCD monitor open first.

A

Flip

down the cover slowly while making sure the gray waterproof seal fits into

the opening at the terminals.

B

Press the entire cover against the camcorder with equal force and firmly attach

the cover completely.

C

Slide the cover until it clicks into place.

(The cover is not properly closed if the red mark at the terminal cover lock is

visible.)

CAUTION

0

Do not apply excessive force when opening or closing the terminal cover.

0

Do

not open or close the terminal cover with wet or dirt/sand-covered hands.

0

Do not allow any dirt, lint, hair, sand, and other foreign substances to

accumulate between the waterproof seal and the case.

0

Never damage or scratch the waterproof seal and terminal cover. Doing so

can result in leaks. If the seal is damaged, contact your nearest JVC Service

Center for a replacement. (Charges apply.)

0

Read the “Detailed User Guide” carefully before using the camcorder under

water or in places exposed to water droplet.

(Rear)

EN 9

Charging the Battery

A battery is built into the camcorder.

.

To AC Outlet

(110 V to 240 V)

AC Adapter

(Provided)

Adapter Cable

(Provided)

Charging Lamp

A

B

C

D

1

Open the terminal cover (p. 9)

2

Connect adapter cable to AC adapter.

3

Plug in the AC adapter to AC outlet (110 V to 240 V).

4

Connect the other side to USB socket on the unit.

CAUTION

0

At the time of purchase or in case of the battery is not used for a long period

of

time, the charging time will be longer than usual. The camera does not turn

on if the remaining battery power is low. In this case, charge the battery for

more than 40 minutes before turning on the power.

0

Charging time: Approx. 6 h 10 m (when charging at 25°C (77°F))

0

The battery cannot be charged outside the room temperature range of 10°C

to 35°C (50°F to 95°F). The CHARGE lamp does not light up when the battery

is not being charged. If the temperature increases or decreases during

charging, the CHARGE lamp will blink slowly and charging will stop. In this

case, remove the AC adapter, press the Reset button and wait until the room

temperature is within the above stated range before charging again.

0

You can record or play back videos during charging. (However, the charging

time will be longer than usual. In addition, the remaining battery power may

decrease according to conditions.) If the internal temperature rises when

using the unit, stop the charging temporarily. (The CHARGE lamp goes off.)

0

If malfunctions (such as overvoltage) occur, charging will stop. In this case,

the CHARGE lamp blinks quickly as a notification.

0

When the recording time becomes extremely short even when the battery is

fully charged, the battery needs to be replaced. For details on replacing the

built-in battery (subject to a fee), consult the nearest JVC service center.

0

For details on other charging methods, please refer to the “Detailed User Guide”.

10 EN

Inserting an SD Card

The videos and the still images are recorded to the built-in memory at the initial

settings.

Insert a commercially available SD card if you want to record to the SD card.

.

*

Insert an SD card.

Before inserting the SD card,

close the LCD monitor to turn off

this unit.

(Rear)

Label

Open the terminal cover.

o

To remove the SD card

Push the SD card inward once, then pull it out straight.

NOTE

Operations are confirmed on the following SD cards.

Manufacturer Panasonic, TOSHIBA, SanDisk

Video A

Class 4 (

K

) or higher compatible SD card (2 GB)/

Class 4 (

K

) or higher compatible SDHC card (4 GB to 32 GB)/

Class 4 (

K

) or higher compatible SDXC card (64 GB to 128 GB)

0

When recording with video quality [UXP], Class 6 or

higher is recommended.

Still Image B

SD card (256 MB to 2 GB) / SDHC card (4 GB to 32 GB) /

SDXC card (64 GB to 128 GB)

0

Using SD cards (including SDHC/SDXC cards) other than those specified

above may result in recording failure or data loss.

0

This

unit is not guaranteed to operate with all SD cards, even when using the

ones specified above. Some SD cards may not work due to specification

changes, etc.

0

To protect the data, do not touch the terminals of the SD card.

0

When using an SDXC card, check its compatibility with the OS of your

computer by referring to the Detailed User Guide.

0

Do not use a miniSD card or microSD card (even if the card is inserted in an

adapter). It may cause malfunction to the camcorder.

EN 11

Video Recording

You can record without worrying about the setting details by using the P

(Intelligent

Auto) mode. Settings such as exposure and focus will be adjusted automatically to

suit the shooting conditions.

Before recording an important scene, it is recommended to conduct a trial recording.

.

H

P

A

C

A

T

W

Check if the recording

mode is A video.

If the mode is B still image,

tap B on the touch screen,

then tap A to switch.

Start recording.

Press again to stop.

Zooming

(Wide angle)

(Telephoto)

Zoom Lever

If the mode is H Manual, tap H on

the touch screen, then tap P to

switch.

Check if the recording mode

is P.

0

You can also tap

6

on the touch screen to record. To stop recording, tap

7

. In addition, you can also tap

D

to zoom.

12 EN

o

Indications during video recording

.

MENU

PLAY

0:00:00 [0:54]

REC

Recording in Progress

Recording-Standby

Battery Indicator

Recording Media

Image Stabilizer

Video Quality

Remaining Recording

Time

Scene Counter

Still Image

Recording Button

NOTE

0

The

estimated recording time of the supplied battery is approximately 2 hour

50 minutes of actual recording and up to 5 hours 10 minutes of continuous

recording.

0

Do not remove SD card when the POWER/ACCESS lamp is lighted. The

recorded data may become unreadable.

0

With [AUTO POWER OFF] operation, the camera automatically turns off if no

operation is performed for 5 minute, in order to conserve power. (The unit

enters into standby mode when the AC adapter is used.)

0

The angle of view may change when the image stabilizer is turned on or off.

0

When recording underwater, the internal mechanical noise (such as zooming

sound) may be easily picked up and recorded. This is not a malfunction.

o

Attaching the Core Filter

Attach the core filter to the AV Cable as shown in the illustration. The core filter

reduces interference when this unit is connected to other devices.

.

3 cm (1-3/16”)

To be connected to this unit

Release the

stopper.

Wind once

EN 13

Playing Back/Deleting Files on this Unit

Select and play back the recorded videos or still images from an index screen (thumbnail

display).

.

T

W

VOL.

Tap on the files to delete.

Ta p R.

To delete unwanted files

Turn up the

volume

Turn down

the volume

Volume adjustment

during playback

Ta p u to return to the video

index screen.

Tap on the file to play back.

Tap "SET".

Ta p E to return to the

recording mode.

Ta p F on the touch screen

to select the playback mode.

Ta p e to pause playback.

Tap "OK".

Tap "EXECUTE" when the

confirmation message appears.

Ta p A or B to select the video

or still image mode.

A I mark appears on the selected file.

To remove the I mark, tap again.

DELETE

SEL ALL REL ALL SET

QUIT

Ta p I/J to select the media for

playback.

o

To capture a still image during playback

A

Pause the playback with e.

B

Press the START/STOP button or tap the A on the LCD.

NOTE

0

While this unit may be used with the LCD monitor reversed and closed, the

temperature rises more easily. Leave the LCD monitor open when using this

unit.

0

The

power may turn off to protect the circuit if the temperature of this unit rises

too much.

14 EN

Install Everio MediaBrowser (Windows 10)

Everio MediaBrowser is included with

your camera. It lets you archive and

organize your videos. It also lets you

create discs and upload video to

YouTube, and other popular web sites.

1

Open the terminal cover.

2

Connect the USB cable.

0

Before connecting the USB cable,

close the LCD monitor to turn the

camera off.

.

To USB

Connector

USB Cable

(Provided)

To USB

Connector

3

Open the LCD monitor to

turn on this unit.

o

Operation on the camera's touch

screen:

4

Tap [CONNECT TO PC].

5

Tap [PLAYBACK ON PC].

.

PLAYBACK ON PC

CONNECT TO PC

o

Operation on the computer:

6

Perform the following steps.

A

Open the “Start menu”, then

click “All apps”.

B

Click “This PC” in the “Windows

System” menu.

0

If a “This PC” icon is shown on

desktop, double-click the icon

to open “This PC”.

C

Double-click the

“JVCCAM_APP” icon in the

“Devices with Removable

Storage” menu.

D

Double-click “install”.

E

Click

“Yes” on the User Account

Control screen.

0

“Software Setup” appears after

a while.

7

Click “Everio MediaBrowser

4”.

.

0

Follow the on-screen instructions.

8

Click “Finish”.

9

Click “Quit”.

0

Installation ends and icons are

created on the desktop.

NOTE

For more information, please refer to the Detailed User Guide.

EN 15

Troubleshooting/Cautions

Troubleshooting

If you encounter problems with this unit,

check the following before requesting

service.

1. Refer to the “Troubleshooting” section

in the “Detailed User Guide”.

If you have difficulties operating the

unit,

refer to the detailed descriptions

in the “Detailed User Guide”.

http://manual3.jvckenwood.com/

index.html/

2. This unit is a microcomputer-controlled

device. Electrostatic discharge,

external noise and interference (from a

TV, a radio, etc.) might prevent it from

functioning properly.

In such a case, reset the unit.

A

Remove all the cables from this

unit.

B

Press the "Reset button" located

inside

of the terminal cover. (Before

pressing the reset button, close the

LCD monitor to turn off this unit.)

C

Reattach the AC adapter, open the

LCD monitor and this unit powers

on automatically.

3. If the above do not solve the problem,

consult your nearest JVC dealer or

JVC service center.

Built-in Battery

This unit is equipped with a built-in

lithium-ion battery. Before using this

Unit, be sure to read the following

cautions:

0

To avoid hazards

…

do not burn.

…

do not modify or disassemble.

…

do not expose this Unit to temperatures

exceeding 60°C (140°F), as this may

cause the built-in battery to overheat,

explode or catch fire.

0

To prevent damage and prolong

service life

…

do not subject to unnecessary shock.

…

charge within the temperature range of

10°C to 35°C (50°F to 95°F). Cooler

temperatures require longer charging

time, or in some cases stop charging at

all.

Warmer temperatures prevent complete

charging,

or in some cases stop charging

at all.

…

store in a cool, dry place. Extended

exposure to high temperatures will

increase natural discharge and shorten

service life.

…

keep a 30% battery level (i) if the

battery is not to be used for a long period

of time.

In addition, fully charge and then fully

discharge the battery every 6 months,

then continue to store it at a 30% battery

level (i).

…

remove the AC adapter from the unit

when not in use, as some machines use

current even when switched off.

…

do not drop intentionally or subject to

strong impact.

The product you have

purchased is powered by a

rechargeable battery that is

recyclable.

Please call 1-800-8-BATTERY for

information on how to recycle this

battery.

(USA and Canada only)

ATTENTION:

16 EN

Recording Medium

0

Be sure to follow the guidelines

below to prevent corruption or

damage to your recorded data.

0

Do not bend or drop the recording

medium, or subject it to strong

pressure, jolts or vibrations.

0

Do not splash the recording medium

with water.

0

Do not use, replace, or store the

recording

medium in locations that are

exposed to strong static electricity or

electrical noise.

0

Do not turn off the camcorder power

during shooting, playback, or when

otherwise accessing the recording

medium.

0

Do not bring the recording medium

near objects that have a strong

magnetic field or that emit strong

electromagnetic waves.

0

Do not store the recording medium in

locations with high temperature or high

humidity.

0

Do not touch the metal parts.

0

When erasing data using the

camcorder, the data won’t be erased

completely. When handing over your

camcorder and/or SD card, you are

recommended to erase all of the data

by either performing “FORMAT” or

“FACTORY PRESET” operation on

this unit, using commercially available

software, or by physically destroying

the camcorder.

LCD Monitor

0

To prevent damage to the LCD

monitor, DO NOT

…

push it strongly or apply any shocks.

…

place

the camcorder with LCD monitor

on the bottom.

0

To prolong service life

…

avoid rubbing it with coarse cloth.

While the LCD monitor screen has

more than 99.99% effective pixels,

0.01% of the pixels may be bright

spots

(red, blue, green) or dark spots.

This is not a malfunction. The spots

will not be recorded.

Main Unit

0

For safety, DO NOT

…

open the camcorder’s chassis.

…

disassemble or modify the unit.

…

allow inflammables, water or metallic

objects to enter the unit.

…

place naked flame sources, such as

lighted candles, on the apparatus.

…

leave

dust or metal objects adhered to

the power plug or an AC wall outlet.

…

insert any objects in the camcorder.

0

Avoid using the unit

…

in places subject to soot or steam such

as near a cooking stove.

…

in places subject to excessive shock

or vibration.

…

near a television set.

…

near appliances generating strong

magnetic or electric fields (speakers,

broadcasting antennas, etc.).

…

in places subject to extremely high

(over 40°C or 104°F) or extremely low

(under -10°C or 14°F) temperatures.

0

DO NOT leave the unit

…

in places of over 50°C (122°F).

…

in places where humidity is extremely

low (below 35 %) or extremely high

(above 80 %) with the terminal cover

open.

…

in direct sunlight.

…

in a closed car in summer.

…

near a heater.

…

in high places such as on a TV.

Leaving the unit in high places while a

cable is connected may result in a

malfunction if the cable is caught and

the unit falls onto the floor.

EN 17

0

To protect the unit, DO NOT

…

drop the unit or strike it against hard

objects.

…

subject it to shock or excessive

vibration during transportation.

…

keep the lens directed at extremely

bright objects for long periods.

…

expose the lens to direct sunlight.

…

swing it excessively when using the

hand strap.

…

swing the soft camcorder case

excessively when the camcorder is

inside it.

…

cover camcorder with a towel, cloth

and so on.

0

To prevent the unit from dropping

0

Fasten the grip belt securely.

0

When using the camcorder with a

tripod, attach the camcorder to the

tripod securely.

If the camcorder drops, you may be

injured and the camcorder may be

damaged.

When a child uses the unit, there must

be parental guidance.

Declaration of Conformity

Model Number : GZ-R460U

Trade Name : JVC

Responsible party :

JVCKENWOOD USA Corporation

Address : 1700 Valley Road Wayne,

N. J. 07470

Telephone Number : 973-317-5000

This device complies with Part 15 of

FCC Rules. Operation is subject to

the following two conditions: (1) This

device may not cause harmful

interference, and (2) this device must

accept any interference received,

including interference that may cause

undesired operation.

Changes or modifications not

approved by JVC could void the

user’s authority to operate the

equipment.

This equipment has been

tested and found to comply with the

limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.

These limits are designed to provide

reasonable protection against

harmful interference in a residential

installation. This equipment

generates, uses, and can radiate

radio frequency energy and, if not

installed and used in accordance with

the instructions, may cause harmful

interference to radio

communications. However, there is

no guarantee that interference will not

occur in a particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined

by turning the equipment off and on,

the user is encouraged to try to

correct the interference by one or

more of the following measures:

Reorient or relocate the receiving

antenna. Increase the separation

between the equipment and receiver.

Connect the equipment into an outlet

on a circuit different from that to which

the receiver is connected.

Consult the dealer or an experienced

radio/TV technician for help.

Refer all servicing to qualified service

personnel. Servicing is required

when the apparatus has been

damaged

in any way, such as power-

supply cord or plug is damaged,

objects have fallen into the

apparatus, ingress of water into the

unit, does not operate normally.

18 EN

MEMO

EN 19

Recordable Time/Specifications

Approximate Video Recording Time

Quality

Built-in

memory

SDHC/SDXC Card

4 GB 4 GB 8 GB 16 GB 32 GB 64 GB 128 GB

UXP 15 m 20 m 40 m 1 h 20 m 2 h 40 m 5 h 40 m 11 h 30 m

XP 20 m 30 m 1 h 1 h 50 m 3 h 50 m 8 h 10 m 16 h 20 m

EP 1 h 20 m 1 h 40 m 3 h 30 m 7 h 14 h 28 h 50 m 57 h 50 m

0

The recordable time is only a guide. The actual recording time may be longer or

shorter than the time indicated above.

Camera

Power supply Using AC adapter: DC 5.2 V

Power

consumption

2.2 W (when [MONITOR BRIGHTNESS] is set to [3] (standard))

Rated Current Consumption: 1A

Dimensions 60 mm x 59.5 mm x 128 mm (2-3/8" x 2-3/8" x 5-1/16")

(W x H x D: excluding grip belt)

Weight Approx. 301 g (0.66 lbs)

The specifications and appearance of this product are subject to changes for

further improvement without prior notice.

For more information, please refer to the Detailed User Guide.

http://manual3.jvckenwood.com/index.html/

US

0318TOH-SW-VM

20 EN

La page charge ...

JVC GZ-R460 Mode d'emploi

JVC GZ-R460 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents