KitchenAid KFCS22EVBL00 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire

Ce manuel convient également à

THANK YOU for purchasing this high-quality product. If you should experience a problem not covered in TROUBLESHOOTING,
please visit our website at www.ldtchenaid.com for additional information. Ifyou still need assistance, call us at 1-800-422-1230.
In Canada, visit our website at www.kitehenaid.ca or call us at 1-800-807-6777.
You will need your model and serial number located on the inside wall of the refrigerator compartment.
Para obtener acceso a "lnstrucciones para el usuario del refrigerador" en espar3ol,o paraobtener informaci6n adicional acerca de
su producto,visite:www.ldtchenaid.com.
Tanga listo sun_mero de modelo completo. Puede encontrar su nQmerode modelo y de serie an la etiqueta ubicada al ledo
derecho del interiordel refrigerador.
Table of Contents / Table des mati res
REFRIGERATOR SAFETY ..................................................................... 1
INSTALLATION INSTRUCTIONS ......................................................... 2
REFRIGERATOR USE ........................................................................... 7
REFRIGERATOR CARE ....................................................................... 10
TROUBLESHOOTING .......................................................................... 11
WATER FILTER CERTIFICATIONS .................................................... 13
PRODUCT DATA SHEETS .................................................................. 14
WARRANTY .......................................................................................... 15
SECURITE DU REFRIGERATEUR ..................................................... 16
INSTRUCTIONS D'INSTALLATION ................................................... 17
UTIUSATION DU REFRIGERATEUR ................................................. 22
EN'I_ETIEN DU REFRIGERATEUR ................................................... 26
DEPANNAGE ........................................................................................ 27
FEUILLES DE DONNEES SUR LE PRODUIT .................................... 30
GARANTIE ............................................................................................ 31
REFRIGERATOR SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance, Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be killed or seriously Injured If you don't Immediately
follow Instructions,
You can be killed or seriously Injured If you don't follow
InstrucUons.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen ifthe instructions are not followed.
12828187A
IMPORTANT SAFETY INSTRUCTIONS
WARNING:To reducethe riskoffire, electricshock,or injuryto personswhen usingtherefrigerator,follow basic precautions,
includingthe following:
Plug intoa grounded 3 pmng outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Disconnect power before servicing.
Replace all parts and panels before operating.
Remove doors from your old refrigerator.
Use nonflammable cleaner.
Keep flammable materials and vapors, such as gasoline,
away from refrigerator.
Use two or more people to move and install refrigerator.
Disconnect power before installing ice maker (on ice maker
kit ready models only).
SAVETHESEINSTRUCTIONS
Proper Disposal of Your Old Refrigerator
IMPORTANT: Child entrapment and suffocation are not problems
ofthe past. Junked or abandoned refrigerators are still dangerous
- even ifthey will sit for "just a few days." Ifyou are getting rid of
your old refrigerator, please follow these instructions to help
prevent accidents.
Before You Threw Away Your Old Refrigerator or Freezer:.
Take off the doors.
Leave the shelves in place sothat children may not easily
climb inside.
INSTALLATION INSTRUCTIONS
Unpack the Refrigerator
When Moving Your Refrigerator:
Your refrigerator is heavy. When moving the refrigerator
for cleaning or service, be sure to protect the floor.
Always pull the refrigerator straight out when moving it.
Do not wiggle or "walk" the refrigerator when trying to move
it, as floor damage could occur.
Remove the Packaging
Remove tape and glue residue from surfaces before turning
on the refrigerator. Rub a small amount of liquid dish soap
over the adhesive with your fingers. Wipe with warm water
and dry.
Do not use sharp instruments, rubbing alcohol, flammable
fluids, or abrasive cleaners to remove tape or glue. These
products can damage the surface of your refrigerator. For
more information, see "Refrigerator Safety."
Dispose of/recycle all packaging materials.
Clean Before Using
Afteryou remove allof the packaging materials, clean the inside of
your refrigerator before using it, See the cleaning instructions in
"Refrigerator Care,"
Important Information to know about glass shelves
and covers:
Do not clean glass shelves or covers with warm water when
they are cold. Shelves and covers may break if exposed to
sudden temperature changes or impact, such as bumping.
For your protection, tempered glass isdesigned to shatter
into many small, pebble-size pieces. This is normal. Glass
shelves and covers are heavy. Use special care when
removing them to avoid impact from dropping.
2
Location Requirements Electrical Requirements
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from refrigerator.
Fallurs to do so can result In death, explosion, or fire.
Toensure proper ventilation for your refrigerator, allow for a 1/_,,
(1.25 cm) space at the top and behind the refrigerator. If your
refrigerator has an ice maker, allow extra space at the back forthe
water line connections. When installing your refrigerator nextto a
fixed wall, leave 21/_''(6.3 cm) minimum on the hinge side (some
models require more) to allow for the door to swing open.
NOTE: It is recommended that you do not install the refrigerator
near an oven, radiator, or other heat source. Do not install the
refrigerator ina location where the temperature willfall below 55°F
(13°(3).
1/2" (1.25 cm)//
JL
21/=" (6.3 cm)
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these Instructions can result in death,
firs, or electrical shock.
Before you move your refrigerator into its final location, it is
important to make sure you have the proper electrical connection.
Recommended Grounding Method
A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded
eleotrioal supply isrequired. It isrecommended that a separate
circuit serving only your refrigerator be provided. Use an outlet
that cannot be turned off by a switch. Do not usa an
extension cord.
NOTE: Before performing any type of installation, cleaning, or
removing a light bulb, turn Cooling OFF, and then disconnect the
refrigerator from the electrical soume. When you are finished,
reconnect the refrigerator to the electrical soume and turn Cooling
ON. See "Using the Controls."
Water Supply Requirements
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
TOOLS NEEDED:
Flat-blade screwdriver V_"Nut driver
7As"and _,_"Open-end or two V_"Drillbit
adjustable wrenches Cordless drill
IMPORTANT:
All installations must meet local plumbing code requirements.
Do not use a piercing-type or _8" (4.76 mm) saddle valve
which reduces water flow and clogs more easily.
Use copper tubing and check for leaks. Install copper tubing
only in areas where the household temperatures will remain
above freezing.
Water Pressure
A cold water supply with water pressure of between 35 and
120 psi (241 and 827 kPa) is required to operate the water
dispenser and ice maker. Ifyou have questions about your water
pressure, call a licensed, qualified plumber.
Reverse Osmosis Water Supply
IMPORTANT: The pressure of the water supply coming out of a
reverse osmosis system going to the water inletvalve of the
refrigerator nsads to be between 35 and 120 psi (241 and
827 kPa).
If a reverse osmosis water filtration system is connected to your
cold water supply, the water pressure to the reverse osmosis
system needs to be a minimum of40 to 60 psi (276 to 414 kPa).
Ifthewaterpressure to the reverse osmosis system is less than
40 to 60 psi (276 to 414 kPa):
= Check to see whether the sediment filter inthe reverse
osmosis system is blocked. Replace the filter if necessary.
= Allow the storage tank on the reverse osmosis system to refill
after heavy usage.
I
If your refrigerator has a water filter, it may further reduce the
water pressure when used in conjunction with a reverse
osmosis system. Remove the water filter. Sea "Water Filtration
System."
If you have questions about your water pressure, call a licensed,
qualified plumbe_
Connect the Water Supply
Read all directions before you begin.
IMPORTANT: Ifyou turn the refrigerator on before the water lineis
connected, turn the ice maker OFE
Connect to Water Line
Connect to Refrigerator
1. Create a service loop (minimum diameter of 2 ft [61 cm])with
the copper tubing. Avoid kinks when coiling the copper
tubing.
2. Remove the plastic cap from water valve inlet port. Place a
compression nut and sleeve on the copper tubing.
3. Insert the end of the copper tubing into the water valve inlet
port. Shape tubing slightly so that the tubing feeds straight
into the port to avoid kinks.
4. Slide the compression nut over the sleeve and screw into the
water valve inlet port.
1. Unplug refrigerator or disconnect power.
2. TurnOFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3. Find a 1_,,to 11/_''(12.7 mm to 31.8 mm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
= Make sure it is a cold water pipe.
I
Horizontal pipe will work, but the following procedure
must be followed: Drillon the top side of the pipe, not the
bottom. This will help keep water away from the drill. This
also keeps normal sediment from collecting in the valve.
4. Determine the length of copper tubing you nead. Measure
from the connection on the rear ofthe refrigerator to the water
pipe. Add 7 ft (2.1 m) to allow for cleaning. Use 1/4"(6.35 mm)
O.D. (outside diameter) copper tubing. Be sure both ends of
copper tubing are out square.
5. Using a cordless drill, drilla 1,,_,,hole in the cold water pipe you
have selected.
A
B
C
D
E
F
G
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
E Shutoff valve
G. Packing nut
6. Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end issolidly in the 1/_,,drilled hole in
the water pipe and that the washer isunder the pipe clamp.
Tighten the packing nat. Tighten the pipe clamp screws slowly
and evenly so the washer makes a watertight seal. Do not
overtighten or you may crush the copper tubing.
7. Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end ofthe tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do net overtighten.
8. Place the free end ofthe tubing in a container or sink, and turn
ON the main water supply. Flush the tubing until water isclear.
TurnOFF the shutoff valve onthe water pipe.
A. Plastic water tubing C. Compression nut
B. Sleeve D. Copper tubing
5. Using an adjustable wrench, hold the nut on the plastic water
lineto keep it from moving. Then, with a second wrench turn
the compression nut on the copper tubing counterclockwise
to completely tighten. Do not overtighten.
A. Plastic water line
B. Water valve inlet port
C. Compression nut
D. Copper tubing
E. "P" clamp
6. Check connection by pulling on copper tubing. Attach copper
tubing to refrigerator cabinet with a "P" clamp. Turn on water
supply to refrigerator and check for leaks. Correct any leaks.
Complete the Installation
Electrical Shock Hazard
Plug Into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these Instructions can result In death,
fire, or electrical shock.
1. Plug into a grounded 3 prong outlet.
4
NOTE: Allow 24 hours to produce the first batch of ice. Discard
the first three batches of ice produced. Allow 3 days to completely
fillthe ice container.
Refrigerator Door(s) and Drawer
Graphics are included later in this section.
Remove and Replace Handles
1. Using a %2"Allen wrench, loosen the two set screws located
on the side of each handle. See Graphics 1 and 2.
2. Pullthe handle straight out from the doo_ Make sure you keep
the screws for rseattachingthe handles.
3. To replace the handles, reverse the directions.
Remove Doors and Hinges
IMPORTANT:
Remove food and any adjustable door or utility bins from
doors.
All graphics referenced inthe following instructions are
included later in this section after "Final Steps."
TOOLS NEEDED: %B",%", 1,_,,hex-head scckst wrench,
#2 Phillips screwdriver, and a fist-blade screwdriver.
1. Unplug refrigerator or disconnect power.
2. Keep the refrigerator doors closed untilyou are ready to lift
them free from the cabinet.
NOTE: Provide additional support for the refrigerator door
while the hinges are being removed. Do not depend on the
door gasket magnets to hold the door in place while you are
working.
3. Starting with the right-hand side door, remove the parts for the
top hinge as shown in Top Hinge graphic. Lift the refrigerator
door from the bottom hinge pin.
NOTE: On some models, remove the shim from the bottom
hinge pin and keep it for later use. See Bottom Hinge graphic.
4,
Before removing the left-hand side door,disconnect the wiring
plug located on top of the top hinge by wedging a fist-blade
screwdriver or your fingernail between the two sections. See
Wiring Plug graphic.
NOTE: The green, ground wire remains attached to the hinge.
5,
Remove the parts forthe top hinge as shown in Top Hinge
graphic. Liftthe left-hand side door from the bottom hinge pin.
NOTE: On some models, remove the shim from the bottom
hinge pin and keep it for later use. See Bottom Hinge graphic.
Replace Doors and Hinges
1. Assemble the parts for the top hinge se shown in Top Hinge
graphic. Do nottighten the screws cemplstely.
2. Replace the parts for the bottom hinge as shown in Bottom
Hinge graphic. Tighten screws. Replace the refrigerator door.
NOTE: Provide additional support for the refrigerator door
while the hinges are being moved. Do not depend on the door
gasket magnets to hold the door in place while you are
working.
3. Align the door so that the bottom of the refrigerator door
aligns evenly with the top of the freezer drawer: Tighten all
screws.
4. Reconnect the wiring plug on top of the left-hand side
refrigerator doo_
5. Replace the top hinge covers.
Remove and Replace Freezer Drawer Front
IMPORTANT: Two people may be required to remove and replace
the freezer drawer front. Graphics are included later inthis
section.
Remove Drawer Front
f. Open the freezer drawer to full extension.
2. Loosen the four screws attaching the drawer glides to the
drawer front. See Drawer Front Removal graphic.
NOTE: Loosen screws three to four turns. Keep the screws in
the drawer front.
3. Lift drawer front upward and oft the screws. See Drawer Front
Removal graphic.
Replace Drawer Front
1. Slide the drawer glides out of the freezer compartment. Insert
the screws inthe top of the drawer front into the slots inthe
drawer brackets. See Drawer Front Replacement graphic.
2. Pull the drawer brackets toward you to position the two
screws inthe bottom of the drawer front into the brackets.
See Drawer Front Replacement graphic.
3. Completely tighten the four screws.
Final Steps
Electrical Shock Hazard
Plug Into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these Instructions can result in death,
fire, or electrical shock.
1. Plug in refrigerator to a grounded 3 prong outlet.
2. Return all removable door parts to doors and food to
rsfrigerator.
Top Hinges
A. Hinge Cover Screw
B. Top Hinge Cover
C. S/l_nHex-Head Hinge Screws
D. Top Hinge
Bottom Hinges
A. Shim (on some models)
B. Bottom Hinge
C. Hinge Screws
Wiring Plug
A. 91_.Set Screw
\
\
\
)A
\
\
\
\
\
A
A. 9/_ Set Screw
6
Adjust the Doors
Your refrigerator has two adjustable, front leveling screws - one
on each side of the refrigerator base. Ifyour refrigerator seems
unsteady or you want the door to close easier, use the instructions
below.
1. Remove the base grille.Grasp the grille firmly and pull it
toward you.
2. Raise or lower the cabinet.
Using a 1,_,,he)( driver,turn the leveling ecrew on each side to
raise or lower that side ofthe refrigerator.
NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws. This
makes it easier to turn the ecrews. It may take several turns of
the leveling screw to adjust the tilt of the refrigerator.
To raise, turn the leveling screw clockwise.
To lower, turn the leveling screw counterclockwise.
REFRIGERATOR USE
Opening and Closing Doors
There are two refrigerator compartment doom. The doors can be
opened and closed either separately or together.
There isa vertically-hinged seal on the left refrigerator doon
When the left side door is opened, the hinged seal
automatically folds inward so that it is out of the way.
When both doors are closed, the hinged seal automatically
forms a seal between the two doom.
O
A. Rear miler adjustment screw
B. Leveling screw
NOTE: Your refrigerator may have a rear rolleradjustment
screw on each side. To raise or lower the rear of the
refrigerator, use a %" hex driver to turn the screws.
3. Open the door again to make sure that it closes as easily as
you like. If not, tilt the refrigerator slightly more to the rear by
turning both leveling screws clockwise. It may take several
more turns, and you should turn both screws the same
amount.
4. Replace the base grille.
A. Hingedseal
Using the Controls
The control center is located at the top front ofthe refrigerator
compartment.
Temperature Controls
For your convenience, your temperature controls are preset at the
factory. When you first install your refrigerator, make sure the
controls are still set to the recommanded set points as shown.
Recommended Settings
IMPORTANT:
The recommended settings should be correct for normal
household refrigerator use. The controls are set correctly
when milk orjuice isas cold as you like and when ice cream is
firm.
When the power ison, the temperature display shows the
actual temperature of the compartment.
Walt 24 hours for your refrigerator to cool completely before
adding food. If you add food before the refrigerator has cooled
completely, your food may spoil.
NOTE: Adjusting the refrigerator and freezer temperature
controls to a colder than recommended setting will not cool
the compartments any faster.
Ifthe temperature istoo warm or too cold inthe refrigerator or
freezer, first check the air vents to be sure they are not
blocked before adjusting the controls.
CoolingOn/Off:.
Cooling On/Off turns off cooling for both compartments. It
does not disconnect power to the refrigerator.
Press and hold Cooling On/Off for 3 seconds. The LED will
light up to indicate that cooling is Off. Press the button again
to turn on the cooling. The LED will turn off.
Adjusting Controls
The REFRIGERATOR control adjusts the refrigerator compartment
temperature. The FREEZER control adjusts the freezer
compartment temperature.
If you need to adjust the temperature in either the refrigerator or
freezer compartment, use the settings listed in the chart as a
guide.
To Adjust Set Point Temperatures:
The first touch of the (+) or (-)touch pad displays the current
temperature set point.
Press the (+) or (-) touch pads until the desired temperature
set point is displayed.
NOTE: Except when firstturning on the refrigerator, do not
adjust either temperature control more than one setting st a
time. Wait 24 hours between adjustments for the temperature
to stabilize.
CONDITION/REASON:
REFRIGERATOR too warm
FREEZER too warm/too little ice
REFRIGERATOR too cold
FREEZER too cold
ADJUSTMENT:
REFRIGERATOR Control
1olower
Adjust FREEZER
Control 1° lower
Adjust REFRIGERATOR
Control 1° higher
Adjust FREEZER
Control 1° higher
Additional Control Center Features
Sabbath Mode
The Sabbath Mode isdesigned for those whose religious
observances require turning off the lightsand dispensers.
ON - All interior lights and alarm tones will be disabled.
OFF - All interior lights and alarm tones will be enabled.
Press and holdthe Sabbath Mode touch pad for 3 seconds or
untilthe indicator light is lit to turn on this feature. Press and
hold the Sabbath Mode touch pad again to turn off this
feature.
m
P_F._3SEC
Door Alarm
The Door Alarm feature sounds a chime every few seconds when
the refrigerator door has been left open for 5 continuous minutes.
The chime will sound untilthe door is closed or Door Alarm is
turned off.
Press the Door Alarm to turn this feature ON or OFE The
indicator light will be lit when the Door Alarm feature is on.
m
Max Cool
The Max Cool feature assists with periods of high refrigerator use,
full grocery loads, or temporarily warm room temperatures.
Press Max Cool to set the freezer and refrigerator to the
lowest temperature settings. Press Max Cool again to return
to the normal refrigerator set point.
NOTE: The Max Cool feature will automatically shut off in
approximately 12 hours.
Filter Reset
The Filter Reset control allows you to restart the water filter status
tracking feature each time you replace your water filter.See
"Water Filtration System."
Press and hold the Filter Reset touch pad for 3 seconds, until
the Order or Replace lightturns off.
_ EP_CE
pI_ESS3_r_
Humidity Control
The Humidity Control feature turns on a heater to help reduce
moisture on the door hinge seal. Use in humid environments or
when you notice moisture on the door hinge seal. The refrigerator
uses more energy when Humidity Control ison.
Press Humidity Control when the environment iswarm and
more humid, or if you notice moisture on the door hinge seal.
The indicator light will be lit when humidity control isON.
Press Humidity Control to save energy when the environment
is less humid.
User Preferences
The control center allows you to set user preferences, if desired.
Temperature Display (F_C)
This preference allows you to change the temperature display.
F - Temperature in degrees Fahrenheit
C - Temperature in degrees Celsius
Alarm (AL)
This preference allows you to turn off the sound of all alarms.
ON - You will hear the alarm sound.
OFF - You will not hear the alarm sound.
8
To Access the User Preferences Menu:
f. Press and hold the Door Alarm touch pad for 3 seconds. The
preference name will appear inthe Freezer display and the
preference status (F or C) or (ON or OFF) will appear in the
Refrigerator display.
2. Use the Freezer (+) or (-) touch pads to scroll through the
preference names. When the desired preference name is
displayed, press the Refrigerator (+) or (-) touch pads to
change the preference status.
3. Set your preferences by pressing and holding the Door Alarm
touch pad for 3 seconds, or by shutting the refrigerator
compartment door.
Crisper Humidity Control
You can control the amount of humidity in the moisture-sealed
crisper. Depending on your model, adjust the control to any
setting between FRUIT and VEGETABLES or LOW and HIGH.
FRUIT / LOW (open) for best storage of fruits and vegetables with
skins.
VEGETABLES / HIGH (closed) for best storage of fresh, leafy
vegetables.
Ice Maker
Turning the Ice Maker On/Off
Toturn the ice maker ON, simply lower the wire shutoff ann.
Tomanually turn the ice maker OFF, liftthe wire shutoff ann to the
OFF (arm up) position and listen for the click.
NOTE: Your ice maker has an automatic shutoff. As ice is made,
the ice cubes will fill the ice storage bin and the ice cubes will
raise the wire shutoff arm to the OFF (arm up)position. Do not
force the wire shutoff arm up or down.
Auto Ice Storage Bin
Your ice storage bin has a lever which allows the storage bin to
slide out with the drawer when it ispulled open or to stay in place.
Move the leverto the right to attach the ice storage bin to the
freezer drawee
Move the leverto the left to release the ice storage bin from
the freezer drawer.
A _
////_, ,, !: !! !_ ,! ;)_
A. Ice storage bin lever
Ice Production Rate
The ice maker should produce a complete batch of ice
approximately every 3 hours.
To increase ice production, lower the freezer and refrigerator
temperature. See "Using the Controls." Wait 24 hours
between adjustments.
Remember
Allow 24 hours to produce the first batch of ice. Discard the
first three batches of ice produced.
The quality of your icewill be only as good as the quality of the
water supplied to your ice maker. Avoid connecting the ice
maker to a softened water supply. Water softener chemicals
(such as salt) can damage parts of the ice maker and lead to
poor quality ice. If a softened water supply cannot be avoided,
make sure the water softener isoperating properly and is well
maintained.
Do not store anything on top of the ice maker or in the ice
storage bin.
Water Dispenser
IMPORTANT:
After connecting the refrigerator to a water source, flush the
water system. Pressthe dispenser paddle for 5 seconds, then
release it for 5 seconds. Repeat until water begins to flow.
Once water begins to flow, continue depressing and releasing
the dispenser paddle (5 seconds on, 5 seconds off) for an
additional 2 minutes. This willflush airfrom the filter and water
dispensing system. Additional flushing may be required in
some households. As air is cleared from the system, water
may spurt out ofthe dispenser.
NOTE: After 5 minutes of continuous dispensing, the
dispenser will stop dispensing water to avoid flooding. To
continue dispensing, press the dispenser paddle again.
Allow 24 hours for the refrigerator to cool down and chill
water. Dispense enough water every week to maintain a fresh
supply.
Dispensing Water
1. Hold a container under the dispenser spout while pressing the
dispenser pad.
2. Release the dispenser pad to stop dispensing.
Water Filtration System
The water filter is located in the upper tight-hand corner of the
refrigerator compartment.
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Lights
The water filter status lights will helpyou know when to change
the water filter.When the Order light is on, it is almost time to
change the water filter.When the Replace light ison, a new water
filter should be installed.
After replacing the water filter, press and hold Filter Reset for
3 seconds untilthe Order or Replace light turns off. See "Using
the Controls."
Replacing theWaterFilter
To purchase a replacement water filter, model 67003523 Part
Number 4396395, contact your dealer or call 1-800-442-9991
U.S.A. or 1-800-807-6777 Canada.
IMPORTANT: Air trapped in the water system may cause water
and filter to eject. Always dispense water for at least 2 minutes
before removing the filteror blue bypass cap.
1. Turnfilter counterclockwise to remove.
2. Remove sealing label from replacement filter and insert the
filter end into the filter head.
3. Turnthe filter clockwise until it stops. Snap the filter cover
closed.
NOTE: The dispenser feature may be used without awater filter
installed. Your water will not be filtered. Ifthis option ischosen,
replace the filter with the blue bypass cap.
REFRIGERATOR CARE
Cleaning
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result In death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section willtransfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
To Clean Your RefdgeratoP.
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent inwarm water.
3. Wash stainless steel and painted metal exteriors with a clean
sponge or soft cloth and a mild detergent inwarm water.
To keep your stainless steel refrigerator looking like new
and to remove minor scuffs or marks, it is suggested that
you use the manufacturer's approved Stainless Steel
Cleaner and Polish, Part Number 4396920. To order the
cleaner, call 1-800-442-9991 U.S.A. or 1-800-807-6777
Canada.
IMPORTANT: This cleaner is for stainless steel parts only!
Do not allow the Stainless Steel Cleaner and Polish to come
into contact with any plastic parts such as the trim pieces,
dispenser covers or door gaskets. If unintentional contact
does occur, clean plastic part with a sponge and mild
detergent in warm water. Dry thoroughly with a soft cloth.
4.
There is no need for routine condenser cleaning in normal
home operating environments. Ifthe environment is
particularly greasy or dusty, orthere issignificant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille.
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
Replace the base grillewhen finished.
5. Plug in refrigerator or reconnect power.
10
Changing the Light Bulb
NOTE: Not all appliance bulbs will fit your refrigerato_ Be sure to
replace the bulb with an appliance bulb of the same size, shape,
and wattage (no greater than 40 watts).
Changing the Refrigerator Light Bulb
1. Unplug the refrigerator or disconnect power.
2. Slide the light shield toward the back ofthe compartmant to
release it from the light assembly.
3. Replace burned-out bulb(s) with appliance bulb(s) no greater
than 40 watts.
4. Replace the light shield by insertingthe tabs on the shield into
the liner holes on each side of light assembly. Slide the shield
toward the front until it locks into place.
NOTE: To avoid damaging the light shield, do not force the
shield beyond the locking point.
5. Pluginrefrigeratororreconnectpower.
Changing the Freezer Light Bulb
1. Unplug refrigerator or disconnect power.
2. Remove the burned-out bulb and replace it with an appliance
bulb no greater than 40 watts.
3. Plug in refrigerator or reconnect power.
TROUBLESHOOTING
Firsttry the solutions suggested here or visit our website and reference FAQs (Frequently Asked Questions)
to possibly avoid the cost of a service cell.
In the U.SA., www.kitchenaid.com In Canada, www.kitchenaid.ca
Refrigerator Operation
The refrigerator will not operate
The motor seems to run too much
Your new refrigerator may run longer than your old one due to its
high-efficiency compressor and fans. The unit may run even
longer if the room is warm, a large food load is added, doors are
opened often, or if the doors have been left open.
The refrigerator seems noisy
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these Instructions can result in death,
fire, or electrical shock.
Power cord unplugged? Plug into a grounded 3 prong outlet.
Is outlet working? Plug in a lamp to see if the outlet is
working.
Household fuse blown or circuit breaker tripped? Replace
the fuse or reset the circuit breaker. Ifthe problem continues,
call an electrician.
Are controls on? Make sure the refrigerator controls are on.
See "Using the Controls."
New installation? Allow 24 hours following installationfor the
refrigerator to cool completely.
NOTE: Adjusting the temperature controls to coldest setting
will not cool either compartment more quickly.
Refrigerator noise has been reduced over the years. Due to this
reduction, you may hear intermittent noises from your new
refrigerator that you did not notice from your old model. Below are
listed some normal sounds with explanations.
Buzzing - heard when the water valve opens to fill the ice
maker
Pulsating - fans/comprassor adjusting to optimize
performance
Hissing/Rattling - flow of refrigerant, movement of water
lines, or from items placed on top of the refrigerator
Sizzling/Gurgling - water dripping on the heater during
defrost cycle
Popping - contraction/expansion of inside walls, especially
during initialcool-down
Water running - may be heard when water melts during the
defrost cycle and runs intothe drain pan
Creaking/Cracking - occurs as ice isbeing ejected from the
ice maker mold.
11
The doors will not close completely
Door blocked open? Move food packages away from door,
Bin or shelf in the way? Push bin or shelf back inthe correct
position,
The doors are difficult to open
Explosion Hazard
Usa nonflammable cleaner.
Failure to do so can result In death, explosion, or fire.
Gaskets dirty or sticky?. Clean gaskets and contact surfaces
with mild soap and warm water. Rinse and dry with soft cloth.
Temperature and Moisture
Temperature is too warm
New installation? Allow 24 hours following installationfor the
refrigerator to cool completely.
Door(s) opened often or left open? Allows warm airto enter
refrigerator. Minimize door openings and keep doors fully
closed.
Large load of food added? Allow several hours for
refrigerator to return to normal temperature.
Controls set correctly for the surrounding conditions?
Adjust the controls a setting colder. Check temperature in
24 hours. See "Using the Controls."
There is interior moisture buildup
NOTE: Some moisture buildup is normal.
Humid room? Contributes to moisture buildup.
Door(s) opened often or left open? Allows humid airto enter
refrigerator. Minimize door openings and keep doors fully
closed.
Ice and Water
The ice maker is not producing ice or not enough ice
Refdgeretor connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open.
Kink in the water source mine?A kink inthe minecan reduce
water flow. Straighten the water seurce line.
Ice maker turned on? Make sure wire shutoff arm or switch
(depending on model) is in the ON position.
New installation? Wait 24 hours after ice maker installation
for ice production to begin. Wait 72 hours for full ice
production.
Freezer door closed completely? Firmly close the freezer
compartment door. Ifthe freezer compartment door will not
close all the way, see "The doors will not close completely."
Large amount of ice recently removed? Allow 24 hours for
ice maker to produce more ice.
Ice cube jammed in the ice maker ejector arm?
Remove ice from the ejector arm with a plastic utensil.
Water filter installed on the refdgerator?. Remove filter and
operate ice maker. If ice volume improves, then the filter may
be clogged or incorrectly installed. Replace filter or reinstall it
correctly.
Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure,
See "Water Supply Requirements,"
The ice cubes are hollow orsmall
NOTE: This is an indication of low water pressure.
Water shutoff valve not fully open? Turn the water shutoff
valve fullyopen.
Kink in the water source line? A kink inthe line can reduce
water flow. Straighten the water source line.
Water filter installed on the refdgeretor? Remove filter and
operate ice maker. If ice quality improves, then the filter may
be clogged or incorrectly installed. Replace filter or reinstall it
correctly.
Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure,
See "Water Supply Requirements,"
Questions remain regarding water pressure? Call a
licensed, qualified plumber.
Off-taste, odor or gray color inthe ice
New plumbing connections? New plumbing connections
can cause discolored or off-flavored ice.
Ice stored too long? Discard ice. Wash ice bin. Allow
24 hours for ice maker to make new ical
Odor transfer from food? Use airtight, moisture proof
packaging to store fOOdl
Are there minerals (such as sulfur) in the water?. A water
fiiter may need to be installedto remove the minerals.
Water filter installed on the refdgeretor? Gray or dark
discoloration in ice indicates that the water filtration system
needs additional flushing. Flushthe water system before using
a new water filteK Replace water filter when indicated. See
"Water Filtration System."
12
Thewaterdispenserwillnotoperate properly
Refrigerator connected to a water supply and the supply
shutoff valve turned on? Connect refrigerator to water
supply and turn water shutoff valve fully open,
Kink in the water source line? Straighten the water source
line.
New installation? Flush and fillthe water system. See "Water
Dispenser."
Is the water pressure at least 35 psi (241 kPa)? The water
pressure to the home determines the flow from the dispense_
See "Water Supply Requirements."
Water filter installed on the refrigerator?. Remove filter and
operate dispenser. If water flow increases, the filter may be
clogged or incorrectly installed. Replace filter or reinstallit
correctly.
Refrigerator door closed completely? Close the door firmly.
If itdoes not close completely, see "The doors will not close
completely."
Recently removed the doors? Make sure the water
dispenser wire/tube assembly has been properly reconnected.
See "Refrigerator Doors."
Reverse osmosis water filtration system connected to
your cold water supply? This can decrease water pressure.
See "Water Supply Requirements."
Water is leaking from the dispenser system
NOTE: One or two drops of water after dispensing is normal.
Glass not being held under the dispenser long enough?
Hold the glass under the dispenser 2 to 3 seconds after
releasing the dispenser lever.
New installation? Flush the water system. See "Water
Dispenser."
Recently changed water filter? Flushthe water system. See
"Water Dispenser,"
Water on the floor near the base grille? Make surethe water
dispenser tube connections are fully tightened. See
"Refrigerator Doors."
Water from the dispenser iswarm
NOTE: Water from the dispenser is only chilled to 50°F (10°C).
New installation? Allow 24 hours after installationfor the
water supply to cool completely.
Recently dispensed large amount of water?. Allow 24 hours
for water supply to cool cernpletely.
Water not been recently dispensed? The first glass of water
may not be cool. Discard the first glass of water.
Refrigerator connected to a cold water pipe? Make sure
the refrigerator is connected to a cold water pipe. See "Water
Supply Requirements."
WATER FILTER
CERTIFICATIONS
469035-750
st_¢ofCa_om_
Dq_t_t of_tb Scr_c_
Water Treatment Device
Certificate Numbe_
03-1583
DamRemed:Apn]22,2(104
Manufacturer:
/ it to Section
\
\
DOnat_e whexe w_te_is " " _d'e or witk waterof _3mown _ality, e_cept that syaems _ f_
cy'_tR'4uct_t m_ybe_d_w_ thatmay_ m,e_abtecyst_
13
PRODUCT DATA SHEETS
Interior Water Filtration System
Model 67003523-750 Capacity 750 Gallons (2839 Liters)
System tested and certified by NSF International against NSF/ANSI
Standard 42 for the reduction of Chlorine Taste and Odor, Particulate
Class I*; and against NSF/ANSI Standard 53 for the reduction of Lead,
Mercury, A_-azine, Toxaphene, Cysts, Turbidity, Asbestos and Lindane.
This system has been tested according to NSF/ANSI Standards 42 and 53 for the reduction of the substances listed below. The
concentration ofthe indicated substances in water entering the system was reduced to a concentration lass than or equal to the
permissible limitfor water leaving the system, as specified in NSF/ANSI Standards 42 and 53.
Substance Reduction NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%
Aesthetic Effects Requirements Influent Concentration Effluent Effluent Reduction Reduction
Chlorine Taste/Odor 50% reduction 1.88 mg/L 2.0 mg/L ± 10% 0.06 mg/L 0.05 mg/L 96.84 >97.26
particles/mL 6g,000 #/mL** 30,583 #/mL 98.94Particulate Class I* 85% reduction 5,700,000 #/mL At least 10,000 99.52
Contaminant NSF Reduction Average Influent Challenge Maximum Average Minimum% Average%
Reduction Requirements Influent Concentration Effluent Effluent Reduction Reduction
Lead: @ pH 6.5 0.010 mg/L 0.153 mg/U 0.15 mg/L ± 10% < 0.001 mg/L < 0.001 mg/L >99.29% >99.35%
Lead: @ pH 8.5 0.010 mg/L 0.150 mg/U 0.15 mg/L ± 10% < 0.001 mg/L < 0.001 mg/L >99.29% >99.33%
Mercury: @ pH 6.5 0.002 mg/L 0.006 mg/L 0.006 mg/L ± 10% 0.0005 mg/L 0.0003 mg/L 90.91 95.70
Mercury: @ pH 5.5 0.002 mg/L 0.006 mg/L 0.006 mg/L ± 10% 0.0015 mg/L 0.0008 mg/L 75.93 56.22
Toxaphene 0.003 mg/L 0.015 mg/L 0.015 ± 10% < 0.001 mg/L < 0.001 mg/L 91.67% 92.97%
Atrazine 0.003 mg/L 0.009mg/L 0.009 mg/L ± 10% < 0.002 mg/L < 0.002 mg/L 75.31% 76.99%
Asbestos 99% 155 MF/L 10'to 10_fibers/L _ < 1 MF/L < 1 MF/L >99.99% >99.99%
Live Cysts _ >99.95% 166,500 #/L 50,000/L min. < 1 #/U < 1 #/L_ >99.99 >99.99
Turbidity 0.5 NTU 10.7 NTU 11 ± 1 NTU 0.49 NTU 0.31 NTU 95.2 97.09
Lindane 0.0002 mg/L 0.002 mg/L 0.002 ± 10% < 0.0001 mg/L 0.000 mg/L 96.50% 98.72%
Test Parameters: pH = 7.5 ± 0.5 unless otherwise noted. Flow = 0.78 gpm (1.9 Lpm). Pressure = 60 paig (413.7 kPa). Temp. = 68°F to
71.6°F (20°C to 22°C).
It is essential that operational, maintenance, and filter
replacement requirements be carried out for the product to
perform as advertised.
The filler monitor system measures the amount of water that
passes through the filler and alerts you to replace the filter.
When 90% of the filter's rated life isused, the yellow (Order)
light comas on. When 100% ofthe filter'srated life isused, the
red (Replace) light comes on, and it isrecommended that you
replace the filter. For models without filler status lights,
replace the filter every 6 months. Use replacement filler model
67003523; order Part Number 4396395. 2007 suggested retail
price of $49.99 U.S.A./S65.95 Canada. Prices are subject to
change without notice.
The product is for cold water use only.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system. Systems certified for cyst reduction may be used
on disinfected waters that may contain filterable cysts.
Refer to the "Water Filtration System" section for the
Manufacturer's name and telephone number.
Refer to the "Warranty" section for the Manufacturer's limited
warranty.
Application Guidelines/Water Supply Parameters
Water Supply City or Well
Water Pressure 35 - 120 psi (241 - 827 kPa)
Water Temperature 33° - 100°F (1° - 38°C)
Service Flow Rate 0.78 gpm (2.9 L/min.) @ 60 psi
*Class I particle size: >0.5 to <1 um
*'Test requirement is at least 100,000 particles/mL of AC Fine Test Dust.
_These contaminants are not necessarily in your water supply. Performance may vary based on local water conditions.
_Fibers greater than 10 um in length
_Based on the use of Cryptosporidium parvum oocysts
® NSF is a registered trademark of NSF International.
14
KITCHENAID ®REFRIGERATOR WARRANTY
ONE YEAR LIMITED WARRANTY
For one year from the date of purchase, when this major appliance isoperated and maintained according to instructions attached to or
furnished with the product, KitchenAid or KltchenAid Canada (hereafter "KitchenAid") will pay for factory specified parts and repair
labor to correct defects in materials or workmanship, Service must be provided by a KitchenAid designated service company,
On models with a water filter: 30 day limited warranty on water filter, For 30 days from the date of purchase, when this filter isoperated
and maintained according to instructions attached to or furnished with the product, KltchanAid will pay for replacement parts to correct
defects in materials and workmanship,
SECOND THROUGH FIFTH YEAR LIMITED WARRANTY ON CAVITY LINER AND SEALED REFRIGERATION SYSTEM PARTS
In the second through fifth years from the date of purchase, when this major appliance isoperated and maintained according to
instructions attached to or furnished with the product, KitchenAid will pay for replacement or repair ofthe refrigerator/freezer cavity liner
(including labor coats) ifthe part cracks due to defective materials or workmanship, Also, in the second through fifth years from the date
of purchase, KitchenAid will pay for factory specified parts and labor to correct defects in materials or workmanship in the sealed
refrigeration system, These parts are: compressor, evaporator, condenser, dryer, and connecting tubing, Service must be provided by a
KltchenAid designated service company,
SIXTH THROUGH TENTH YEAR LIMITED WARRANTY ON SEALED REFRIGERATION SYSTEM PARTS
In the sixth through tenth years from date of purchase, when this major appliance is operated and maintained according to instructions
attached to or furnished with the product, KitchanAid will pay for factory specified parts to correct defects in materials or workmanship
in the sealed refrigeration system, These parts are: compressor, evaporator, condenser, dryer, and connecting tubing,
ITEMS KITCHENAID WILL NOT PAY FOR
1. Service calls to correct the installation of your major appliance, to instruct you how to use your major appliance, to replace or repair
house fuses or to correct house wiring or plumbing.
2. Service calls to repair or replace appliance light bulbs, air filters or water filters.
3. Repairs when your major appliance is used for other than normal, single-family household use.
4. Damage resulting from accident, alteration, misuse, abuse, fire, flood, acts of God, improper installation, installation not in
accordance with electrical or plumbing codes, or use of products not approved by KltchenAid.
5. Any food leas due to refrigerator or freezer product failures.
6. Replacement parts or repair labor costs for units operated outside the United States or Canada.
7. Pickup and delivery.This major appliance isdesigned to be repaired inthe home.
8. Repairs to parts or systems resulting from unauthorized modifications made to the appliance.
9. Expenses for travel and transportation for product service in remote locations.
10. The removal and reinstallation of your appliance if it is installed in an inaccessible location or is not installed in accordance with
published installation instructions.
11. Replacement parts or repair labor costs when the major appliance is used in a country other than the country in which it was
purchased.
DISCLAIMER OF IMPLIED WARRANTIES; LIMITATION OF REMEDIES
CUSTOMER'S SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED
HEREIN, IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, KITCHENAID SHALL NOT BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SOME STATES AND PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, OR LIMITATIONS ON THE DURATION OF IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS, SO THESE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY TO YOU, THIS WARRANTY GIVES
YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE OR PROVINCE
TO PROVINCE,
Outside the 50 United States and Canada, this warranty does not apply. Contact your authorized KitchanAid dealer to determine if
another warranty applies. 5/07
For additional product information, inthe U.S.A., visit www.kitchenaid.com
In Canada, visit www.kitchenaid.ca
If you do not have access to the Internet and you need assistance using your product or you would like to schedule service, you may
contact KitchanAid at the number below.
Have your complete model number ready. You can find your model number and serial number on the label, located on the inside waft of
the refrigerator compartment.
For assistance or service in the U.S.A., call 1-800-422-1230. In Canada, call 1-800-807-6777.
If you need further assistance, you can write to KitchenAid with any questions or concerns at the address below:
In the U.S.A.: In Canada:
KitchenAid Brand Home Appliances
Customer experience Center
553 Banson Road
Benton Harbor, M149022-2692
Please include a daytime phone number in your correspondence.
KitchenAid Brand Home Appliances
Customer Interaction Centre
1901 Minnesota Court
Mississauga, Ontario LSN 3A7
Please keep this User Instructions and model number information for future reference.
15
Nous vous REMERCIONS d'avoir achet6 ce produit de haute qualit6. Si vous rencontrez un probleme non mentionne dans la
section DI_PANNAGE,veuinezvisiter notre site Web www.kitchenaid.com pour des informations suppl6mentaires. Si vous avez
toujours besoin d'assistance, veuiliez nous t_16phoner au 1-800-422-1230. Au Canada, visitez notre site Web www.kitchenaid.ca
ou t616phonez-nous au 1-800-807-6777.
Vous aurez besoin de vos num6res de mod61eet de s_rie situ6s sur la parei interne du compartiment de r_fdg6ration.
SECURITE DU REFRIGERATEUR
Votre sdcurit_ et celle des autres est tr_s importante.
Nous donnons de nombreux messages de s_cudt_ importants dans ca manuel at sur votre appareil m(_nager, Assurez-vous de
toujours lire toss les messages de s_curit_ et de vous y conformer,
Voici le symbole d'alerte de s(_euritd,
Ce symbole d'alerta de s_curit_ vous signale les dangers potentiels de d(_e_s et de blessures graves 8 vous
et _.d'autres,
Tousles messages de s_curit(_suivmnt le symbole d'alerte de s_curit_ et le mot "DANGER" ou
"AVERTISSEMENT", Ces roots signifient :
Risque possible de d6c_s ou de blessure grave sl vous ne
suivez pas immddiatement les instructions,
Risque possible de d6c_s ou de blessure grave sl vous
ne suivez pas los Instructions,
Tousles messages de s_curit_ vous dirent quel est le danger potentiel et vous disent comment r_duire le dsque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
IMPORTANTES INSTRUCTIONS DE S#CURIT#
AVERTISSEMENT : Pour r(_duire les dsques d'incendie, de choc _lectrique ou des blessures Iors de I'utilisationdu
r_frig(_rateur, prendre quelques prdcautions fondamentales, y compds les suivantes :
Brancher I'appareil sur une pdse _ 3 alv_oles reli_e _.la
terre.
Ne pas enlever la broche de liaison _.la terre.
Ne pas utiliser un adaptateur.
Ne pas uUliser un c_.ble de rellonge.
D_brencher la source de courant _lectdque avant
I'entretien.
Replacer pit_ces et panneaux avant de faire la remiss en
marche.
Enlever les portes de votre vieux r_fdg_reteur.
UUliser un produit de nettoyage ininflammable.
Garder les mat_daux et les vapeurs inflammables, telle que
I'essence, loin du r_fdg_rateur.
Utiliser deux ou plus de personnes pour d_placer et
installer le rdfdg_rateur.
D_brencher le r_frig(_rateur avant I'installation de la
machine _ gla_ons (seulement pour modules pr_ts _.
recevoir une machine _ gla_:ons).
CONSERVEZ CES INSTRUCTIONS
16
Mise au rebut de votre vieux r frig rateur
IMPORTANT : Uemprisonnement et 1'6touffemant des enfants ne
sont pes un pmbl6me du pass6. Les r6frig6rateurs jet6s ou
abandonnL=ssont encore dangereux, m_me s'ils sont laies_.s
abandonn_s pendant "quelques jours seulement". Si vous vous
d6barressez de votre vieux r6frig6rateur, veuillez suivm les
instructions suivantes pour aider _ 6viter les accidents.
Avant de jeter votre vieux rdfrigdrateur ou cong61ateur :
Enlever les portes,
Laieser les tablettes en place de sorte que les enfants ne
puissant pas y p6n_trer facilement,
INSTRUCTIONS D'INSTALLATION
D ballage du r frig rateur
Risque du polds excessif
Utlllser deux ou plus de personnes pour ddplacer et
Installer Is r_frlgdrateur,
Le non-respect de cette instruction peut causer
une bleseure au dos ou d'autre bleseure,
Enl_vement des matddaux d'emballage
Enlever le ruban adh_sif et la coils des surfaces du
r6frig6rateur event de le mettre en marche. Frotter une petrie
quantit6 de seven liquids pour la vaieselle sur I'adh_sif avec
les doigts. Rincer & reau tii_=deet eesuyer.
Ne pes utiliser d'instruments coupants, d'alccol _ friction, de
liquides inflammables ou de nettoyants abrasifs pour enlever
le ruben adh_sif ou la colle. Ces produris peuvent
endommager la surface de vctre r6frig6rateur. Pour plus de
renesignements, voir "S6curit6 du r6frig6rateur".
Jeter ou recycler tous les mat6riaux d'emballage.
D6placement de votre rdfrlg6rateur :
Votre r6frig6rateur est Iourd. Lors du d6placement du
r6frig6rateur pour le nettoyage ou le service, veiller _tprot6ger
le plancher. Toujours tirer le r6frig6rateur tout drori Iors du
d6placement. Ne pes incliner le r6frig6rateur d'un cbt6 ou de
rautre nile "faire marcher" en esseyant de le d6placer car le
plancher pourrait _tre endommag&
Nettoyage avant I'utilisation
Apr_s avoir enlev6 tousles mat6riaux d'emballage, nettoyer
I'int_rieur du r_frig_rateur avant de rutiliser.Voir les instructions de
nettoyage dens "Entretien du r6frig6rateur".
Importants renselgnements t_sevolr au sujet des tablettes
st des couvercles en verre :
Ne pas nettoyer les tablettes ou couvercles en verre avec de
I'eau tilde quand ils sent froids. Les tablettes et les
couvercles peuvent se briser s'ils sont exposes _.des
changements soudains de temperature ou _ un impact tel
que coup brusque. Pour votre protection, le verre tremp_ est
con_u pour 8clater en d'innombrables piercesminuscules.
Ceci est normal. Les tablettes et les couvercles en verre sont
Iourds. Un soin special s'impose Iors de leur d_placement
pour _viter I'impact d'une chute.
Exigences d'emplacement
Risque d'exploslon
Garder les matdrlaux et les vapeurs inflammables, telle
que reseence, loin du rdfrlg6rateur.
Le non-respect de cette Instruction peut causer
un d6c_s, une explosion ou un Insendle.
Pour assurer une ventilation convenable & votre r6frig6rateur,
laieser un espace de V2"(1,25 cm) en haut e[ derriere le
r_frig6rateur. Si votre r6frig6rateur comporte une machine
glagons, s'essumr qu'un espace addriionnel est pr6vu & I'arri_re
pour permettre les connexions des conduits d'eau. En cas
d'installation du r6frig_rateur pros d'un mur fixe, laisesr un
minimum de 21/_'' (6,3 cm) du cbt_ de la charni_re (certains
mod61esn6ceesrient davantage d'espace) pour permettre & la
porte de s'ouvrir sans obstruction.
17
REMARQUE : II eat mcommand6 de ne pss installer le
r6frigGrateur prbs d'un four, d'un radiateur ou de toute autm
source de chaleu_ Ne pss installerle rGfrigGrateurdana un endroit
oQla tempGrstum balssera au-dessous de 55°F (13°C).
,,,om,/
21/2" (6,3 cm)
Specifications lectriques
Risque de choc dlectrlque
Brancher sur une prise b 3 alv6oles relide b la terra.
Ne paa enlever la broche de liaison t_la terra.
Ne pas utlllsar un adaptataur.
Ne pas utlllser un cable de rallonge.
La non-respect de ces instructions peut causer
un ddc&s, un Incendle ou un choc 61ectrlque.
Avant de placer le rGfrigGrateurb son emplacement final, il eat
important de vous assurer d'avoir la connexion 61ectrique
apprepriGe.
M6thode recommand6e de mise b la terre
Une source d'alimentation de 115 volts, 60 Hz, type 15 ou
20 ampbrss CA seulement, protGgGepar fualblss et
ad6quatement miss Gla terra sat ndcsssaire. II sat recommand6
d'utiliser un circuit distinct pour alimenter uniquement votre
r_frig6rsteur. Utiliser une prise murals quine pant pas _tre raise
hors circuit b.I'aide d'un commutateur. Ne pas utiliser de c&ble de
rallonge.
REMAROU E :Avant d'ex6cuter tout type d'installation, nettoyage
ou remplacement d'une ampoule d'Gclalrage, dGsactiver le
refreidissemant (mettre la commands Cooling en position OFF), st
dGconnecter ensuite le r6frig6rateur de la source d'alimentation
61ectrique. Lorsque vous avez terminG, reconnecter le
r6frigGrsteurb la source d'alimentation 61ectdque etrdactiver le
refroidissement (mettre la cemmande Cooling en position ON).
Voir "Utilisation des commandss".
Specifications de l'alimentation en eau
Rassembler lea outils et pi_ces n_cessaires avant de commencer
I'installation. Lire et suivre lea instructions fourniss avec lea outils
indiqu6s ici.
OUTILLAGE REQUIS :
Tournevis _ lame plate Tourne-6creu de %"
Cl_s plates de zAs"et 1,_,,ou Forst de %"
deux cl6s b molstte rdglablss Perceuss sans fil
IMPORTANT :
Toutes lea installations doivent _tre conformss aux exigences
des codes Iocaux de plomberie.
Ne pas employer de robinet d'arr_t _ _rier de _6" (4,76 mm)
ou de type b percer, ce qui rdduit le d6blt d'eau et cause une
obstruction plus facilement.
Utiliser untube en cuivreet v6rifiers'il y a des fuites, installer
Iss tubes en cuivre seulement Gdes endrelts oQ la
temp6rature ss maintient au-dsssus du point de cong61ation.
Pression de l'eau
Une alimentation en eau freide avec une pression entre 35 et
120 Ib/po2(241 et 827 kPa) eat n6csssalre pour faire fonctionner
le distributeur d'eau st la machine b glagons. Si vous avez des
questions au sujst de la pression de votre eau, appeler un
plombier qualifi6 agr6&
AlimentatJon en eau par osmose inverse
IMPORTANT : La pression de I'alimentation en eau entre le
systbme d'cemcee inverse et la valve d'arriv_e d'eau du
r6fdg6rateur dolt 6tre entre 35 et 120 Ib/po2 (241 et 827 kPa).
Si un syst_me de purification de I'eau par osmoss inverse sat
raceord_ b vctre alimentstion an eau froide, la pression de I'eau
au systGme dolt _tre d'un minimum de 40 b 60 Ib/po2(276 G
414 kPa).
Si la pression de I'eau au systbme d'osmose inverse eat inf_rieure
40 b 60 Ib/po2(276 _ 414 kPa) :
V_rifier pour voir si lefiltre Gs6diment du systbme d'osmose
inverse eat bloqu_ et le remplacer si n_csssalre.
Laisser le r_servoir du systbme d'osmose inverse se remplir
apr6s une utilisation intense.
Si vctre r_frig_rateur a un filtre Geau, celui-ci peut r6duire
encore plusla pression de I'eau Iorsqu'elle eat utilis6e avec un
syst6me d'osmose inverse. Retirer le filtre _ eau. Voir
"Systbme de filtration de I'eau".
Si vous avez des questions au sujet de la pression de votre eau,
appalez un plombier qualifi6 agr_.
Raccordement de la canalisation d'eau
Liratoutes lea instructions avant de commencer.
IMPORTANT : Si on dolt utiliser le r_ffig6rateur avant qu'il soit
raceord6 b la canalisation d'eau, placer la commands de la
machine b glagons & la position OFF (arr6t).
Raccordement b une canalisation d'eau
1. D_brancher le r_frig_rateur ou d6cennecter la source de
courant 61ectdque.
2. FERMER le robinet principal d'arriv6e d'eau. OUVRIR Is
rcbinst de puissge le plus proche pendant une p_riode
suffisante pour qua la cenalisation d'eau se vide.
18
3. Trouver une canalisetion d'eau froide verticale de 1_,,&1W' 4. Faire glisser I'_cmu de compression sur la bague, serrer pour
(12,7 mm _31,8 mm) pres du refrigerateur, le fixer ear I'orifice d'arrivee d'eau.
IMPORTANT :
Aseurez-vous qu'il s'agit d'un conduit d'eau froide.
Un conduit horizontal fonctionnera, male le precede
suivant dolt 6tre suivi : percer par le dessus de la
canalisetion et non pss par le dessoue. Ainsi, I'eau ne
riequera pse d'arroeer la perceuse. Ceci emp_che
6galement Ise s_liments qu'on trouve normalement dane
reau de s'acoumuler dane le robinet.
4. Pour determiner la Iongueur du tube en cuivm, il faut mseurer
la distance separant le point de connexion situ6 e I'arriere du
refrigerateur et la canalieation d'eau. Ajouter une Iongueur de
7 pi (2,1 m) pour permettre le deplacemant du reffigerateur
pour le nettoyage. Utiliser un tube en cuivre de Y_"(6,35 mm)
de diam_tm exterieu_ Veiller e ce que letube seit coupe
d'_luerre aux deux extremit_s.
5. Lors de I'utilisetion d'une perceuse sans ill, percer un trou de
_" dane letuyau de canalisation d'eau froide choisie.
A
B
C
D
E
F
G
A. Canalisation d'eau froide
B. Bride de tuyau
C. Tube en cuivre
D. _crou de compression
E.Bague de compression
£ Robinet d'atr_t
G. _crou de serrage
6. Fixer le robinet d'arr_t sur la canalisation d'eau froide avec la
bride de tuyau. Verifier que le raccord du robinet est bien
engage dane le trou de _/_"peru6 done la canalisetion et que la
rondelle d'_tanch_it_ est plac_e sous la bride de tuyau. Serrer
1'ecroude serrage. Serrer lentement et uniformement lee vie
de la bride de tuyau afln que la rondelle forme une jonction
6tanche. Ne pse serrer excessivement car ceci pourrait
provoquer 1'ecrasement du tube en cuivre.
7. Enfiler I'ecrou et la bague de compreseion du raccord sur le
tube en cuivre comme on levolt ear I'illustration. Insemr
I'extremit_ dutube aussi loin que possible dane I'ouverture de
sortie du mbinet. Visser I'_cmu de compression sur le raccord
de sortie avec une cl_ e molette. Ne pse serrer
excsesivement.
8. Placer le bout libre du tube dons un contenant ou evier et
OUVRIR le robinet principal d'arrivee d'eau. Laisser I'eau
s'ecouler par le tube jusqu'fi ce que I'eau soit limpide.
FERMER le robinet principal d'arrivee d'eau.
Raccordement au refdgerateur
1. Crier use boucle de service (diam_tm minimum de 2 pi
[61 cm]) avec le tube de cuivre. I_viter lee deformations en
pliant le tube de coivre.
2. Retirer le capuchon de plsetique du robinet d'arrivee d'eau.
Placer un ecmu de compression et use bague ear letube de
cuivre.
3. Inserer I'extremite du tube de cuivre dane I'orifice d'arrivee
d'eau. Ajuster le tube de cuivre de fagon & ce qu'il s'adapte
parfaitement e I'orifice d'arrivee d'eau pour eviter Iss
deformations.
A. Tube en plastique pour
canalisation d'eau
B. Bague
C. _crou de
compression
D. Tube de cuivre
5. A I'aide d'une cle _ molette, fixer 1'ecmu sur la canalieation
d'eau pour I'empecher de se deplacer. Ensuite, e raide d'une
deuxieme cI6, tourner I'ecrou sur letube de coivre dane le
sene antihoraire pour serrer compl_tement. Ne pse serrer
excsesivement.
A. Canalisation d'eau en C. _crou de compression
plastique D. Tube de cuivre
B. Orifice d'anivee d'eau E.Bdde en "P"
6. Verifier la eolidite du racoordement en tirant sur le tube de
cuivre. Fixer le tube de cuivre_ la caisse du r_frig_rateur e
I'aide d'une bride en "P". Ouvrir la canalisation d'eau du
r_frigerateur et inspecter s'il y a des fuitse. Corriger toute fuite.
Achever I'installation
Risque de choc 61ectrlque
Brancher sur une prise b 3 alvdoles rell_e b la terre.
Ne pas enlever la broche de liaison b la terre.
Ne pas utlllser un adaptateur.
Ne pas utlllser un c_ble de rallonge.
Le non-respect de ces Instructions peut causer
un ddc_s, un Incendle ou un choc 61ectrlque.
1. Brancher ear use prise e3 alveolse reli_e & iaterre.
REMARQU E : Prevoir un dalai de 24 heures pour la production du
premier lot de glac,,ons.Jeter Iss trois premiers lots de gla(;ons
produits. Prevoir un delai de 3jours pour le mmplissege complet
du recipient e glad;one.
19
Porte(s) et tiroir du r frig rateur
Les illustrations eont incluses plus loin dons cette section. 3. Aligner correctement la porte au niveau du bas de la porte du
Enl6vement et r_installation des poign6es
1. A I'aide d'une cl6 Allen de _", dessarrer les deux vie de
rstenue situ_es cur le cbt_ de chaque poign6e. Voir lee
illustrations 1 et 2.
r6frig6rateur et du deesus du tiroir de cong61ation. Sarmr
toutes lee vie.
4. Reconnecter la fiche de branchement eur la partie eup6rieure
de la porte du c6t6 gauche du r6frig6rateur.
5. R6installar lee caches de la charni_re sup6rieure.
2. Tirar sur la poignde tout droit pour la sortir de la porte.
S'essurar de girder lee vie pour r_installar lee poigndes.
3. Pour r6installar lee poign6es, suivre les instructions dane
I'ordre inverse.
Enl&vement des portes et des charnieres
IMPORTANT:
D6pose et r6installation de la faP_adedu tiroir
de cong61ation
IMPORTANT : Deux personnes peuvent _tre n_cessalres pour
retirer et r6installer de lafaqade du tiroir de cong61ation. Lee
illustrations eont incluses plus loin dane cstte section.
Retirer lee aliments et tout balconnet ou compartiment
utilitaire des portes.
Touteslee illustrationsmentianndes dane leeinstructions
suivantessont induses plusloindanecstte sectionapr_s "l_tapes
finales".
D6pose de la fae_ade du tiroir
1. Ouvrir letimir de cong61ation compl_temant.
2. Deeserrer lee qustre vie fixant lee gliesi_res dutiroir &la facade
du tiroir.Voir I'illustration de d6pose de I'avant du tiroir.
REMARQUE : Deeserrar lee vie an appliquant trois _ quatre
tours. Laieser lee vie cur lafacade du tiroir.
OUTILLAGE REQUIS : CI6s _.douille & lame hexagonale de Ks",
%" st 1A",tournevis Phillips 2 et tournevis _t_te plate.
1. D6brancher le r6frig6rateur ou d6connecter la source de
courant 61ectdque.
2. Laieser le r_frig6rateur farm6 jusqu'& ce vous soyez pr_t & le
soulever de la calese.
REMARQUE : Pr6voir un support additionnel des portes
pendant la r6installation des charni_res. La force d'attraction
dee aimants dee portes ne euffit pie _ lee maintenir an place.
3,
En commen(_ant par la porte du c6t6 droit, 6tar lee pi6ces de
la charniere sup6rieum - voir I'illustration de la charni6re
sup6rieure. Soulever la porte du r_frig6rateur de I'axe de la
charni_re inf_deure.
REMARQUE : Sur certalne modules, 6tar la cale de I'axe de la
charni_re inf_rieurast la conserver pour utilisation ult6deum.
Voir I'illustration de la charni_re inf6rieure.
4. Avant de retirer la porte du cbte gauche, d_connectar la fiche
de branchemant situee sur la partie superieure de la charniere
sup6deura en coin(;ant un tournevis & lame plate ou votre
ongle entre les deux sections. Voir I'illustration de la Fiche de
branchemant.
REMARQUE : Le conducteur vert et le conducteur de liaison
&la terra restent fix6s _ la charni_re.
5. Enlevar lee pi_.ee de la charni6re sup6rieure - voir I'illustration
de la charni6re sup_rieure. Soulever la porte du c6t6 gauche
de I'axe de la charni_ra inf_rieure.
REMARQUE : Sur certalns modules, 6tar la cale de I'axe de la
charni_re inf_rieurest la conserver pour utilisation ult_deure.
Voir I'illustrstion de la charni_re inf6rieure.
Remplacement des portes et des chami_es
1. Assembler lee pi6ces de la charni_re sup6rieure. Voir
I'illustration de la charni_re sup6rieure. Ne pas compl_tement
serrar lee vie.
2,
Replacer lee pi6ces de la charni_re inf_rieure. Voir I'illustration
de la charni6re inf_rieure. Resserrer lee vie. Replacer la porte
du r6fdg6rateur.
REMAROUE : Pr_voir un support additionnel des portes
pendant la r6inetallation des charni6res. La force d'attraction
des aimante dee portee ne euffit pes _ lee maintenir an place.
3. Glieser la fagade du tiroir vers le haut et hors dee vis. Voir
rillustration de d_pese de ravant du tiroir.
R6installation de la fa_ade du tiroir
1. Tirar lee gliesi_res du tireir hors du compartiment de
cong_lation, InsUrer lee vie au sommet de la facade du tireir
dane lee trous situ_s sur lee brides du tiroir,Voir rillustration
de r6installation de ravant du tiroir,
2. Tirar lee brides du tiroir vars vous pour placer lee deux vis au
bas de lafagade du tiroir dins les brides. Voir I'illustration de
r_installation de ravant du timir.
3. Serrarcompl_tement leequstre vie.
Etapes finales
Risque de choc 61ectrlque
Brancher sur une prise & 3 alvdoles rellde & la term.
Ne pas enlever la broche de liaison tala term.
Ne pie utlllser un adaptateur.
Ne pas utlllser un c&ble de rallonge.
Le non-respect de ces instructions peut causer
un ddc&s, un Incendle ou un choc dlectrlque.
1. Branchar sur une pdse &3 alv6oles reli6e _ laterra.
2. R_installar toutes lee pieces amovibles dane lee portes; y
ranger lee aliments.
2O
1 / 1

KitchenAid KFCS22EVBL00 Le manuel du propriétaire

Catégorie
Frigos
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues