Alula RE206M Manuel utilisateur

RE206M
Marque
Alula
Modèle
RE206M
Taper
Manuel utilisateur
Tilt Sensor is a full-featured security transmitter typically
used to sense the tilt of overhead garage doors and
windows. It will alarm when the sensor is tilted more
than 45 degrees.
Features
• Industry-leading wireless range and battery life
Enroll by placing the panel into wireless enrollment
mode and then sending an enrollment signal from the
sensor.
Sending an Enrollment Signal
Remove the battery tab and cover to trip
tamper. Select desired Loop:
• Loop 1: Tilt Alarm when tipped to vertical
• Loop 2: Tilt Alarm when tipped to at
• Loop 3: Not used
• Loop 4: Tamper
Install by mounting the sensor to the
inside of a door or window using the
mounting screw locations. For garage
door installations, the sensor should be
mounted to the top panel of the overhead
door. This ensures that the sensor
closes only when the door is fully
closed, and is best for RF range.
Tilt Detection occurs when the
sensor exceeds a 45 degree angle.
If the sensor rotates further than
135 degrees, it is likely to remain
in a non-alarm state. For best
results, the sensor should rotate
within 90 degrees to ensure an
alarm state occurs.
RE206M Tilt Sensor
Honeywell & 2GIG Compatible
I
N
S
T
A
L
L
G
U
I
D
E
I
Mounting
Screw
Holes
Cover-Securing
Screw Hole
Use the panel installation guide to verify proper system setup.
Resolution Compatibles
FCC NOTICE
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference that may be received,
including interference that may cause undesired operation.
Changes or modications not expressly approved by Alula could
void the user’s authority to operate this equipment.
FCC ID: U5X-RE201
IC NOTICE
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two conditions:
(1) This device may not cause interference, and
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux cnr d’Industrie Canada
applicables aux appareils radio exempts de licence. L’exploitation
est autorisée aux deux conditions suivantes:
(1) L’appareil ne doit pas produire de brouillage, et
(2) L’utilisateur de l’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
IC: 8310A-RE201
TRADEMARKS
Alula is a trademark owned by Alula Holdings, LLC. All trademarks,
logos and brand names are the property of their respective owners.
All company, product and service names used in this document are
for identication purposes only. Use of these names, trademarks and
brands does not imply endorsement.
Alula products will function with one of either Honeywell or 2GIG
systems. However, no Alula product is produced by, endorsed
by, nor is ofcially associated with Honeywell or 2GIG. Alula
recommends verifying proper enrollment and operation, per control
panel installation instructions, at installation.
Specications
Physical
Housing Dimensions
Weight with Battery
Mounting Fastener
Cover-Securing Screw
(optional, not provided)
3.25 x 1.40 x 1.05 inches (8.3 x 3.6 x 2.7 cm)
1.90 ounces (54 grams)
#4 or #6 screws (not provided)
Pan Head, #1 x .25 inches, A/AB Thread Forming (sheet metal)
screw, McMaster 90190A051
Environmental
Operating Temperature
Maximum Humidity
32 to 120 °F (0 to 49 °C)
85% non-condensing relative humidity
Sensor Specications
Frequency
Replacement Battery
Battery Life
Battery Voltage
Current Draw
Transmitted Indications
345 MHz
One Panasonic CR123A
10 to 15 years
3.0 VDC (Nominal), 2.2 VDC (Low)
20 mA (Maximum), 0.6 uA (Quiescent)
Cover Tamper, Low Battery, Supervision
Certication
RE206M FCC, IC
Specications subject to change without notice.
Pro Tips
3M VHB Tape works great for mounting if the surface is properly prepared and rm
pressure is applied for over 10 seconds.
Surface Preparation
• Clean the surface
• Ensure the mounting surface temperature is above 50 °F
47-00021-02 • REV A • 2022-06-15
Tech Support Line • (888) 88-ALULA • (888) 882-5852
alula.com
  • Page 1 1
  • Page 2 2

Alula RE206M Manuel utilisateur

RE206M
Marque
Alula
Modèle
RE206M
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes