Access Lighting 20825LEDD Manuel utilisateur

Taper
Manuel utilisateur
WHAT YOU NEED
Screwdriver
Wire Cutters
Wiring Supplies as Specified
by Electrical Code
INSTALLATION INSTRUCTIONS
WHAT WE PROVIDE
Mounting Hardware
1 x Glass shade
LED
COLLECTION
1
CERTIFICATION: cETLus DAMP
NO. 20825LEDD/20826LEDD
20825LEDD
20826LEDD
APPLICATION MODEL NO.
FLUSH MOUNT
IMPORTANT SAFETY INSTRUCTIONS
MESURES DE SECURITE A RESPECTURE
Before assembling your ACCESS LIGHTING fixture, please make sure that
you carefully read through this instruction sheet. Save this instruction sheet
and refer to it when additions to or changes in the fixture
configuration are made.
Lisez attentivement ce manuel d’instructions. Enregistrer cette feuille
d'instructions et de s'y référer lorsque les ajouts ou changements dans
la configuration de montage sont faites.
CONSULT A QUALIFIED ELECTRICIAN TO ENSURE CORRECT BRANCH
CIRCUIT CONDUCTOR.
CONSULTER UN ELECTRICIEN QUALIFIE POUR VOUS ASSURER QUE LES
CONDUCTEURS DE LA DERIVATION SONT ADEQUATS
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION
AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.
CE PRODUIT DOIT ETRE INSTALLE SELON LE CODE D’INSTALLATION PERTINENT,
PAR UNE PERSONNE QUI CONNAIT BIEN LE PRODUIT ET SON FONCTIONNEMENT
AINSI QUE LES RISQUES INHERENTS
NOTE: The important safeguards and instructions that appear in this
manual are not meant to cover all possible conditions and situations
that may occur. It must be understood that common sense, caution and
care, are factors that can’t be built into any product. These factors must
be supplied by the person(s) caring for and operating the fixture.
Read all instructions
Do not install this fixture in hazardous locations.
N'installez pas cet appareil dans des emplacements dangereux.
Do not install any fixture assembly closer than 6 inches from any
curtain or similar combustible material.
Laisser une distance d’au moins 6 pouces entre ce luminaire et la toute
surface combustible.
"WARNING Risk of Fire and Electric Shock."
“CAUTION: Risque d’ Incendie et de Choc Electriques.
GENERAL INFORMATION
All electrical connections must be in accordance with all ordinances,
Local and the U.S. National Electrical Codes (NEC). These fixtures are
intended for mounting to a standard 4” metal octagon outlet box.
The box must be directly supported by the building structure and U.L.
Recognized.
STEP BY STEP INSTRUCTIONS
Before starting your installation disconnect the Power by turning off the
Circuit Breaker or by removing the fuse at the fuse box. Just turning the
light off at the light switch is not sufficient to prevent electrical shock.
Recommended Dimmers
Lutron DVCL-153P
Lutron CTCL-153P
Lutron TGCL-153P
Lutron MACL-153M
Lutron PD-6WCL
Lutron MRF2-6CL
ROMA
PREPARE FIXTURE AND MAKE WIRE
CONNECTIONS
If there is an existing fixture remove it. Expose the
supply wires from the J-box. Connect the black supply
wire to the black fixture wire. Secure with the supplied
wire nuts. Connect the white supply wire to the white
fixture wire. Secure with the supplied wire nuts. Attach
the green J-Box wire around green hexagonal head
screw or connect it to the green supply grounding wire
of the fixture. Secure all wires with electrical tape
(not supplied).
Tuck all wires carefully into the J-Box.
1
WHAT YOU NEED
Screwdriver
Wire Cutters
Wiring Supplies as Specified
by Electrical Code
2
2
CERTIFICATION: cETLus DAMP NO.
20825LEDD/20826LEDD
3
MOUNT THE FIXTURE
Align the fixture canopy to the J-box and secure
with the supplied screws.
Align the glass shade to the fixture and secure by
rotating the glass clockwise until secured against the
fixture body.
RESTORE THE ELECTRICITY AND
CHECK THE OPERATION OF YOUR
NEW ACCESS LIGHTING FIXTURE
If the fixture is to be removed or replaced,
please ensure that the electricity is
switched off and that the fitting is cool
before touching it.
CAUTION
VER: 21.11.1
  • Page 1 1
  • Page 2 2

Access Lighting 20825LEDD Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues