WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1
INSTALLATION INSTRUCTION
PD-47813S\PD-47825S\PD-47841S
• Read all instructions before installing.
• System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
• When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
• Retain installation instructions for future maintenance reference.
All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by dweLED. Substitution of parts or accessories not designated for use with this product by dweLED could
result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
Coastal conditions may cause mineral and residue build-up on the xture. We recommend that customers in coastal
areas clean all external surfaces of the xture once every two weeks with a wet cloth.
• Lisez toutes les instructions avant l’installation.
• Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux
règlements locaux.
• Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement
avec les pièces et/ou accessoires fournis pour être utilisés avec les produits dweLED. Remplacer des pièces ou accessoires non conçus pour ce
produit dweLED pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
Les conditions côtières peut causer une accumulation de minéraux et de résidue sur le luminaire. Nous recommendons
aux clients qui resident dans les zones côtières de nettoyer toutes les surfaces externes du luminaire une fois toutes les deux semaines avec
un chion humide.
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
INSTALLATION INSTRUCTION
1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
3. Loosen the mounting screw (B) from the xture, and remove the mounting back plate.
4. Drill holes in the wall aligned with the key holes located on the mounting back plate. Insert the plastic anchor (D)
5. Secure the mounting back plate to the junction box using standard junction box screws that comes with the junction box.
Fasten the mounting back plate to the wall with the plastic anchors using the wood screws (C) provided.
Note: (i) Using any other non-original-manufacturer provided junction box screw may result in safety issue;
(ii) The side of the mounting plate marked “GND” must face out.
Junction box and wood screws combined holding strength must be able to adequately support the weight of the chandelier
greater than 50 lbs. see weight chart below:
6. Adjust the xture wire length by pushing the cable gripper on the canopy and pulling the wire as desired.
a) Before securing the canopy in place, it is recommended to retract or extend the wire within the canopy to a desirable length.
b) Due to limited space within the canopy, shorten the cable as necessary to make the installation easier. Make sure to identify and
label all the wiring properly before any trimming/shortening (Fig. 3).
7. Connect the xture, CCT switch, and driver's output wires to center cable as shown in Fig. 3, red to the green,
black to the black, blue to the white, brown to the bare, make sure that wire connectors(A) are secured.
Then tuck them inside the canopy.
8. The lamp can switch between four color temperatures (2700K-3000K-3500K-4000K),
which can be adjusted to your preference with the switch in the canopy (Fig.5).
the switch comes with a detachable cover, remove the cover prior to adjusting the color temperature,
reattach the cover after adjustment is made.
9. Connect the driver’s input wires to junction box wires as shown in Fig. 2, make sure that all wire connectors(A) are secured.
If your outlet box has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s
ground wire directly to the back plate using the screw provided. After wires are connected, tuck them carefully inside the junction box.
10. This xture features electronic low voltage (ELV or TRIAC) or 0-10V dimming capabilities. See notes below for specic
dimming wires information.
11. To utilize ELV or TRIAC dimming: use black (hot), white (neutral) and bare copper ground wires (ground).
12. To utilize 0-10V dimming: use purple (dim+), gray or pink (dim-), black (hot), white (neutral) and bare copper ground wires (ground).
NOTE: Make sure to connect 0-10V prior to power-up the xture in order to allow the 0-10V dimming to function properly.
13. Secure the xture to the mounting back plate using the mounting screw (B). (Fig. 1)
PD-47813S\PD-47825S\PD-47841S
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
3
INSTALLATION INSTRUCTION
PD-47813S\PD-47825S\PD-47841S
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Dec.2023
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
4
INSTALLATION INSTRUCTION
PD-47813S\PD-47825S\PD-47841S
White - Neutral
Black - Hot Purple - Dim+
Gray or Pink - Dim-
Red - Fixture+
Black - Fixture-
3000K 2700K4000K
Switch
3500K
-
1
-
2
-
3
-
4
WAC Lighting PD-47813S Mode d'emploi
- Taper
- Mode d'emploi
dans d''autres langues
Documents connexes
-
WAC Lighting PD-29425 Mode d'emploi
-
-
-
-
-
-
-
-
-