1WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Stealth Framing Projector Monopoint
MO-1210
OVERALL FIXTURE DIMENSIONS
SPECIFICATIONS
Input: 120-277V, 50/60Hz
Installation: 3/0, 4/0 Junction Box
Dimming: ELV, TRIAC (120V only)
FIXTURE OVERVIEW
Monopoint is intended for direct surface mount installation to an NEC
approved junction box.
CAUTION: TO PREVENT ELECTRICAL SHOCK, ENSURE ELECTRICITY HAS BEEN TURNED OFF AT THE CIRCUIT BREAKER
BEFORE BEGINNING.
-Read all instructions before installing.
-System is intended for installation by a licensed electrician in accordance with the National Electrical Code (NEC) and local regulations.
-When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
-Retain installation instructions for future maintenance reference.
WARNING: All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or
accessories designated for use by WAC Lighting. Substitution of parts or accessories not designated for use with this product by WAC Lighting
could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are
damaged or missing.
MISE EN GARDE: POUR ÉVITER TOUT CHOC ÉLECTRIQUE, ASSUREZVOUS QUE LE DISJONCTEUR SOIT MIS HORS TENSION AVANT DE
COMMENCER.
-Lisez toutes les instructions avant l’installation.
-Le système doit être installé par un électricien licensié conformément au code national de l’électricité (NEC), et également aux règlements
locaux.
-Lors de la manipulation du luminaire, n’appuyez pas sur les LED. Tenez-le uniquement par la base.
ATTENTION: Toutes les pièces doivent être utilisées comme indiqué dans ces instructions. Ce produit est conçu pour être utilisé seulement avec
les pièces et/ou accessoires fournis pour être utilisés avec les produits WAC Lighting. Remplacer des pièces ou accessoires non conçus pour ce
produit WAC Lighting pourrait causer des dommages corporels ou matériels et pourrait également causer l’annulation de la garantie. Veuillez
contacter un revendeur autorisé ou le fabricant si des pièces manquent ou sont endommagées.
HARDWARE
Wire Connector
Qty: 3 (+1 Extra) Mounting Screw
Qty: 1 (+1 Extra)
33
AB
5
s
"
Ø5
z
"
m
"
1
2
"
5
s
"
2WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1a”
1w”
44”
Mounting Back Plate
Dimensions
INSTALLATION INSTRUCTIONS
Stealth Framing Projector Monopoint
MO-1210
FIG. 1
FIG. 3
Junction Box Screws
Phillips Screwdriver
PREPARATION:
clear area. Be careful not to lose any small parts necessary for
installation.
MOUNTING THE FIXTURE:
and secured by the mounting screw.
1.
FIG. 1).
2. Secure the mounting back plate to the junction box using the
appropriate junction box screws (See FIG. 3).
NOTE: The side of the mounting back plate marked “GND” must
face out.
FIG. 2
Ø
Loosen the mounting screw (B) to remove the mounting back
3WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
FIG. 5
FIG. 4 Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
FIG. 6
FIG. 7
FIG. 8
Fixture GND (Green)
(White)
Wire Connector
(Black)
Green or Bare wire
INSTALLATION INSTRUCTIONS
Stealth Framing Projector Monopoint
MO-1210
CONNECTING THE POWER WIRES:
1. Connect xture wires to building wires: insert each supply wire
into appropriate junction box wire connector (see FIG. 4). The
xture ground wire may be secure to the mounting plate ground
screw terminal. Alternatively, it may be spliced and connected to
existing building ground wiring (see FIG. 5).
2. This xture features electronic low voltage (ELV) dimming
capabilities. To utilize ELV, wire black (line hot), white (line netural),
and green (ground) in accordance to dimmer specications.
3. Make sure that all wire connectors (A) are secure. If your outlet
box has a green or bare copper ground wire, connect the xture’s
ground wire to it. Otherwise, connect the xture’s ground wire
directly to the mounting back plate using the green screw
provided.
4. After wires are connected, tuck them carefully inside inside the
junction box.
SECURING THE CANOPY:
1. With wire connections placed inside the junction box, raise
canopy towards the ceiling (see FIG. 6).
2. Align the mounting plate tabs to the open grooves of the canopy.
Turn the canopy clockwise (CW) to fasten it to the mounting
plate. (see FIG. 7).
3. Secure the canopy to the mounting plate and ceiling by fastening
the provided mounting screw. (see FIG. 8).
4WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Stealth Framing Projector Monopoint
MO-1210
FIG. 9
90°
from
vertical
360°
PROJECTOR ADJUSTMENT:
1. Gently support recently turned on xture body with one hand.
Point light directly at the center object to be illuminated.
2. Rotate the xture dials to zoom and focus light to best eect.
(See FIG. 10)
FIXTURE AIMING AND ADJUSTMENT:
Fixture is capable of 90 degree vertical aiming and 360 degree
horizontal rotation. (See FIG. 9)
FIG. 10
rotation focus
beam angle
3. To ‘frame’ an object with light, open the four framing shims
outward to the maximum, and then push them inward one
by one. Focus can be adjusted after framing. Repeat steps as
necessary to achieve best results. (See FIG. 11)
4. To orientate the rotation of the frame or Gobo accesory, loosen
the thumb screw, rotate the lens about the xture body to align.
When complete, tighten the thumb screw to x the lens. (See
FIG. 12)
FIG. 11
OR OR
FIG. 12
Thumb
screw lock
rotation
5WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. JAN 2024
waclighting.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
INSTALLATION INSTRUCTIONS
Stealth Framing Projector Monopoint
MO-1210
GOBO ACCESSORY INSTALLATION: (Gobos by others, reference spec sheet for size compatibility )
1. With xture uninstalled, remove the thumbs screw and underside screw to remove projector front assembly.
2. Rotate upper lens counterclockwise to remove it.
3. Rotate gobo holder counterclockwise to remove it.
4. Remove accessory lock ring by rotating it counterclockwise or by tool to remove it.
5. Place Gobo in accessory holder with the colored or coated (less shiny) surface faces downward (further from LED). (See FIG. 13)
6. Be sure all surfaces are clean and reverse process to complete installation.
FIG. 13
Accessory
lock ring
Upper lens
assembly
Loosen
top ring
Do not loosen this middle
ring which holds the
optical lenses.
Underside
screw
Thumb screw Gobo holder
Gobo
(Colored or
coated surface
faces downward)
CLEANING AND MAINTENANCE
1. If debris or rough areas appear on projection image, remove projector front assembly (see FIG. 13) and gently wipe lenses and internal
shims with dust-free or microber cloth.
-
1
-
2
-
3
-
4
-
5
dans d''autres langues
Documents connexes
-
WAC Lighting 9000-MLV Mode d'emploi
-
-
WAC Lighting 1061-27SS Mode d'emploi
-
-
-
-
-
-
-