Chief FCA623B Guide d'installation

Chief
Marque
Chief
Modèle
FCA623B
Catégorie
Mur
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
XPAU Dual Monitor Extension
Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
FCA623
FCA623 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM: A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY: AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT: A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
each display and attached accessories does not exceed 250
lbs (113.4 kg) or 125 lbs (56.7 kg) per display after the
FCA623 accessory has been installed to the XPAU. See
Figure below for details.
WARNING: RISK OF SERIOUS INJURY OR DEATH! Use
with televisions weighing more than the maximum weight
indicated may result in the cart collapsing or overturning onto
a person causing serious injury or death!
WARNING: Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING: Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING: Do not use this product outdoors.
NOTE: The FCA623 has no user serviceable parts.
--SAVE THESE INSTRUCTIONS--
125 lbs (56.7 kg) per display
250 lbs (113.4 kg)
for entire mounting system
Installation Instructions FCA623
3
DIMENSIONS
38.20
970.2
FCA623 Installation Instructions
4
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
Installation Instructions FCA623
5
TOOLS REQUIRED FOR INSTALLATION
PARTS
#2
1/8” (included)
3/16” (included)
1/2”
B (2)
[Right upright]
A (2)
[Left upright]
C (1)
[Interface extension]
D (1)
[Dual screen cover]
E (3)
#10-24 x 1 1/2” F (1)
1/8”
H (2)
[Hardware bag B - quantities listed per bag]
HA (4)
M6x12mm HB (4)
M6x16mm HC (4)
M6x25mm
HD (4)
1/4” HE (4)
1/2”
HF (4)
M8x12mm HG (4)
M8x16mm HH (4)
M8x25mm HI (2)
1/4-20 x 1 1/4”
G (1)
3/16”
FCA623 Installation Instructions
6
Assembly And Installation
The FCA623 is specifically designed to convert Chief’s XPAU
carts into 2x1 monitor mounting systems. Do not attempt to
install the FCA623 onto any other mounting device!
1. Remove two Phillips screws and right side cover from right
side of XPAU interface head assembly. (See Figure 1)
Figure 1
2. Remove four screws and washers holding tilt bracket and
head assembly to column assembly. (See Figure 2)
3. Remove two stability knobs and spacers from head
assembly. (See Figure 2)
4. Remove tilt plate and head assembly from column
assembly. (See Figure 2)
Figure 2
5. Remove four nuts holding interface head assembly to XPAU
column assembly to remove head assembly. (See Figure 3)
Figure 3
6. Remove three screws holding plates to FCA623 interface
(C) in order to remove back plate. (See Figure 4)
Figure 4
x 2
1
XPAU
x 4
2
4
3
stability
knobs x 2
x 4
5
tilt plate
x 3
6
back plate
Installation Instructions FCA623
7
Figure 5
(rear view)
connecting brackets
7
back plate tilt plate
front plate
(E x 3/removed screws x 3)
10
removed
9
nuts x 4
on top
7. Slide two of four connecting brackets from XPAU head
assembly into corresponding groove on FCA623 interface.
(See Figure 5)
8. Align four connecting brackets with outside four holes on tilt
plate. (See Figure 5)
9. Use four nuts removed in Step 4 to secure tilt plate to new
head assembly. (See Figure 5)
10. Install six #10-24 x 1 1/2” flat head cap screws (E and
removed screws) through front plate, new head assembly,
tilt plate and back plate to create complete head assembly.
(See Figure 5)
IMPORTANT ! : Make sure back plate and front plate are
reassembled correctly. The triangles must be at the top
when they are reattached! (See Figure 5)
11. Place new head assembly onto column assembly. (See
Figure 6)
12. Use four screws and washers removed in Step 2 to reattach
tilt plate to column assembly. (See Figure 6)
13. Reinstall two stability knobs and spacers through stability
plates and into head assembly. (See Figure 6)
Figure 6
11
x 4
12
s
stability
knobs x 2
13
FCA623 Installation Instructions
8
Display Installation
1. Place display face down on a soft, non-abrasive surface.
NOTE: For best access, route display cables through columns
prior to display installation. See Cable Management
section for details.
CAUTION: Using screws of improper diameter may
damage your display! Proper screws will easily thread into
display mounting holes.
2. Select screw diameter by examining hardware (HA-HC and
HF-HH) (6mm or 8mm) and comparing with mounting holes
on display. (See Figure 7)
3. Select spacers:
• If mounting holes are not recessed and interface
brackets (A and B) can lay flat against display,
then no spacers are required.
• If mounting holes are recessed, or if protrusions
prevent brackets (A and B) from laying flat, then
spacers (HE) must be used.
CAUTION: Using screws of improper length may damage
your display! Proper screws will have adequate thread
engagement without contacting bottom of display mounting
holes.
4. Select screw length: (See Figure 7)
• Using your hand, insert SHORTEST length screw
of selected diameter (HA or HF) through 1/4”
washer (HD), bracket (A or B), selected spacer
(HE, if required), into display mounting hole. Do
NOT thread screw into hole at this time.
• Proper screw length requires base of screw head
to protrude above flat washer a distance equal to
or greater than the screw diameter. If screw
length is inadequate, select longer screw. Select
shortest screw which will protrude the required
distance.
5. Use selected screws (HA-HC or HF-HH), washers (HD) and
spacers (HE), if necessary, to connect interface brackets (A
and B) to back of display. Make sure diamond on interface
brackets is even with center of display. (See Figure 7)
Figure 7
(HE) x 4, if necessary
(A)
(B)
(HA-HC or HF-HH) x 4
5
(HD) x 4
Installation Instructions FCA623
9
WARNING: Exceeding the weight capacity can result in
serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the combined weight of
each display and attached accessories does not exceed 250
lbs (113.4 kg) or 125 lbs (56.7 kg) per display after the
FCA623 accessory has been installed to the XPAU.
6. Hang interface brackets (A and B) to display rails. (See
Figure 8)
7. Use 1/4-20 x 1 1/4” socket head cap screws (HI) to secure
interface brackets (A and B) to rails for each display. Screws
must engage through both holes to be fully secured. (See
Figure 8)
NOTE: Display positions may need to be adjusted after height
and/or plumb adjustments in order to maintain desired
alignment.
Figure 8
Dual Screen Cover Installation (Optional)
NOTE: Installation of dual screen cover (D) is for aesthetic
purposes only and is completely optional.
NOTE: Cover may be install above or below head assembly
depending on the position of the head assembly.
1. Remove displays from head assembly. (See XPAU
installation instructions)
2. Install dual screen cover (D) into open area of column
assembly, above or below head assembly. (See Figure 9) or
(See Figure 10)
Figure 9
Figure 10
(HI) x 2
underside view
7
(below head assembly)
(D)
(above head assembly)
(D)
FCA623 Installation Instructions
10
Adjustments
Height Adjustment
1. Use upper knob on back of interface brackets (A and B) to
adjust the height of each display. (See Figure 11)
NOTE: Adjust both brackets in order to maintain a level mount.
Plumb Adjustment
2. Use middle and lower knobs on back of interface brackets
(A and B) to make plumb adjustments to each display (See
Figure 11)
Figure 11
1
1
2
2
(display not shown for clarity)
Installation Instructions FCA623
11
FCA623 Installation Instructions
USA/International A 6436 City West Parkway, Eden Prairie, MN 55344
P800.582.6480 / 952.225.6000
F877.894.6918 / 952.894.6918
Europe A Franklinstraat 14, 6003 DK Weert, Netherlands
P+31 (0) 495 580 852
F+31 (0) 495 580 845
Asia Pacific A Office No. 918 on 9/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief, a products division of
Milestone AV Technologies
8800-002579 Rev03
2016 Milestone AV Technologies
www.milestone.com
06/16
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Chief FCA623B Guide d'installation

Chief
Marque
Chief
Modèle
FCA623B
Catégorie
Mur
Taper
Guide d'installation
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes