Chief PACTP1 Guide d'installation

Catégorie
Mur
Taper
Guide d'installation
INSTALLATION INSTRUCTIONS
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
PFC Cart Series Stabilizer Accessory
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
PACTP1
PACTP1 Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively "Milestone"), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
IMPORTANT WARNINGS AND
CAUTIONS!
WARNING: A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION: A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
WARNING: Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all components are
properly assembled and installed using the instructions
provided.
Installation Instructions PACTP1
3
LEGEND
Tighten Fastener
Apretar elemento de fijación
Befestigungsteil festziehen
Apertar fixador
Serrare il fissaggio
Bevestiging vastdraaien
Serrez les fixations
Loosen Fastener
Aflojar elemento de fijación
Befestigungsteil lösen
Desapertar fixador
Allentare il fissaggio
Bevestiging losdraaien
Desserrez les fixations
Phillips Screwdriver
Destornillador Phillips
Kreuzschlitzschraubendreher
Chave de fendas Phillips
Cacciavite a stella
Kruiskopschroevendraaier
Tournevis à pointe cruciforme
Open-Ended Wrench
Llave de boca
Gabelschlüssel
Chave de bocas
Chiave a punte aperte
Steeksleutel
Clé à fourche
By Hand
A mano
Von Hand
Com a mão
A mano
Met de hand
À la main
Hex-Head Wrench
Llave de cabeza hexagonal
Sechskantschlüssel
Chave de cabeça sextavada
Chiave esagonale
Zeskantsleutel
Clé à tête hexagonale
Pencil Mark
Marcar con lápiz
Stiftmarkierung
Marcar com lápis
Segno a matita
Potloodmerkteken
Marquage au crayon
Drill Hole
Perforar
Bohrloch
Fazer furo
Praticare un foro
Gat boren
Percez un trou
Adjust
Ajustar
Einstellen
Ajustar
Regolare
Afstellen
Ajuster
Remove
Quitar
Entfernen
Remover
Rimuovere
Verwijderen
Retirez
Optional
Opcional
Optional
Opcional
Opzionale
Optie
En option
Security Wrench
Llave de seguridad
Sicherheitsschlüssel
Chave de segurança
Chiave di sicurezza
Veiligheidssleutel
Clé de sécurité
PACTP1 Installation Instructions
4
TOOLS REQUIRED FOR INSTALLATION
PARTS
3/16" 5/32"
(included) (included)
A (2)
[side pitch bracket]
B (1)
[column attachment bracket] C (2)
[side attachment bracket]
D (10)
1/4-20 x 1/2" E (2)
5/16-18 x 1" F (2)
1/4" G (1)
3/16" H (1)
5/32"
Installation Instructions PACTP1
5
Bracket Installation
1. Assemble cart assembly according to installation
instructions included with cart.
2. Remove rear two 5/16-18 x 3/4" button head cap screws
from cart stand. (See Figure 1)
Figure 1
3. Connect two side pitch brackets (A) to faceplate using four
1/4-20 x 1/2" button head cap screws (D). (See Figure 2)
Figure 2
4. Connect column attachment bracket (B) to side attachment
brackets (C) using four 1/4-20 x 1/2" button head cap
screws (D). (See Figure 4)
Figure 3
5. Secure column attachment bracket (B) to cart column using
two 5/16-18 x 1" button head cap screws (E). (See Figure 4)
6. Use pitch adjustment knob to adjust pitch to desired level.
(See Figure 4)
7. Connect two side attachment brackets (C) to side pitch
brackets (A) using two 1/4-20 x 1/2" button head cap screws
(D) and two 1/4" washers. (See Figure 4)
Figure 4
2
X 2
(A) x 2
(D) x 4
2
(C) x 2 (B)
(D) x 4
4
7
(D) x 2
(F) x 2
(C) x 2
(B)
5
(E) x 2
pitch
adjustment
knob
PACTP1 Installation Instructions
6
Pitch Adjustment
1. Loosen two 1/4-20 x 1/2" button head cap screws (D)
locking pitch position of the mount. (See Figure 5)
2. Use pitch adjustment knob to adjust pitch to desired level.
(See Figure 5)
3. Tighten two 1/4-20 x 1/2" button head cap screws (D) to lock
pitch position back into place. (See Figure 5)
Figure 5
2
13
Installation Instructions PACTP1
7
PACTP1 Installation Instructions
USA/International A 8401 Eagle Creek Parkway, Savage, MN 55378
P800.582.6480 / 952.894.6280
F877.894.6918 / 952.894.6918
Europe A Fellenoord 130 5611 ZB EINDHOVEN, The Netherlands
P+31 (0)40 2668620
F+31 (0)40 2668615
Asia Pacific A Office No. 1 on 12/F, Shatin Galleria
18-24 Shan Mei Street
Fotan, Shatin, Hong Kong
P852 2145 4099
F852 2145 4477
Chief Manufacturing, a products division
of Milestone AV Technologies
8800-002082 Rev00
2011 Milestone AV Technologies, a
Duchossois Group Company
www.chiefmfg.com
04/11
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Chief PACTP1 Guide d'installation

Catégorie
Mur
Taper
Guide d'installation

dans d''autres langues