Astria Fireplaces LSS-35CP Guide d'installation

Marque: Astria Fireplaces

Modèle: LSS-35CP

Catégorie: Cheminées

Taper: Guide d'installation

Ce manuel convient également à

DIRECT VENT

SPECTRA SERIES

LSS-35CN LSS-40CN

LSS-35CP LSS-40CP

OTL Report No. 116-F-02b-5

Portland

MODELS

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or mobile

home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated on the rating

plate. This appliance is not convertible for use with other gases unless a certiﬁed kit is used.

INSTALLATION INSTRUCTIONS

P/N 850016M Rev. N 02/2013

This manual is one of a set of two supporting this product.

Refer to P/N 875020M for Care and Operation Instructions.

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 850016CF.

AVERTISSEMENT : Assurez-vous de bien suivre les

instructions données dans cette notice pour réduire au

minimum le risque d’incindie ou d’explosion ou pour

éviter tout dommage matériel, toute blessure ou la mort.

- Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs

ou liquides inﬂammables dans le voisinage de cet appareil

ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir des

téléphones se trouvant dans le bâtiment où vous trouvez.

• Appelez immédiatement votre fournisseur de gaz depuis

un voisin. Suivez les instructions du fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par un

installateur ou un service d’entretien qualiﬁé ou par le

fournisseur de gaz.

WARNING: If the information in these instructions

is not followed exactly, a ﬁre or explosion may

result, causing property damage, personal injury,

or death.

vapors and liquids in the vicinity of this or any other

appliance.

- WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

•

department.

- Installation and service must be performed by a

WARNING /AVERTISSEMENT / AVISO

• HOT GLASS WILL CAUSE

BURNS.

• DO NOT TOUCH GLASS

UNTIL COOLED.

• NEVER ALLOW CHILDREN

TO TOUCH GLASS.

• UNE SURFACE VITRÉE CHAUDE

PEUT CAUSER DES BRÛLURES.

• LAISSER REFROIDIR LA SURFACE

VITRÉE AVANT D'Y TOUCHER.

• NE PERMETTEZ JAMAIS À UN ENFANT

DE TOUCHER LA SURFACE VITRÉE.

• EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

• USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

• LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

INSTALLATEUR : Laissez cette notice avec l'appareil.

CONSOMMATEUR : Conservez cette notice pour

consultation ultérieure.

Children and adults should be alerted to the

hazards of high surface temperature and

should stay away to avoid burns or clothing

ignition.

Les enfants et les adultes devraient être infor-

més des dangers que posent les températures

de surface élevées et se tenir à distance aﬁn

d’éviter des brûlures ou que leurs vêtements

ne s’enﬂamment.

DO NOT ATTEMPT TO ALTER OR MODIFY

THE CONSTRUCTION OF THE APPLIANCE OR

ITS COMPONENTS. ANY MODIFICATION OR

ALTERATION MAY VOID THE WARRANTY, CER-

TIFICATION AND LISTINGS OF THIS UNIT.

WARNING

Young children should be care-

fully supervised when they are

in the same room as the appli-

ance. Toddlers, young children

and others may be susceptible

to accidental contact burns. A

physical barrier is recommended

if there are at risk individuals in

the house. To restrict access to

a ﬁreplace or stove, install an

adjustable safety gate to keep

toddlers, young children and

other at risk individuals out of

the room and away from hot

surfaces.

AVERTISSEMENT

Les jeunes enfants devraient être

surveillés étroitement lorsqu’ils

se trouvent dans la même pièce

que l’appareil. Les tout petits,

les jeunes enfants ou les adultes

peuvent subir des brûlures s’ils

viennent en contact avec la sur-

face chaude. Il est recommandé

d’installer une barrière physique

si des personnes à risques habi-

tent la maison. Pour empêcher

l’accès à un foyer ou à un poêle,

installez une barrière de sécu-

rité; cette mesure empêchera les

tout petits, les jeunes enfants et

toute autre personne à risque

d’avoir accès à la pièce et aux

surfaces chaudes.

GENERAL INFORMATION

These appliances are designed to operate on

natural or propane gas. An electronic intermit-

tent pilot ignition system provides safe, efﬁcient

operation. External electrical power (110 vac)

is recommended to operate these units. If the

system operates on line voltage with 6V fan

control module, four (4) "AA" batteries can be

used as a backup in case of a power outage. The

electronic appliance can be operated without a

fan, solely with four (4) "AA" batteries.

These vented gas ﬁreplace heaters are sealed

combustion, air-circulating gas ﬁreplaces de-

signed for residential applications.

Approved Vent Components - These ﬁreplaces

are designed, tested and listed for operation

and installation with, the following vent com-

ponents only:

• Secure Vent™ Direct-Vent System Compo-

nents manufactured by Security Chimneys

International,

• Secure Flex™ Flexible Vent Components

manufactured by Security Chimneys Inter-

national and

• Z-FLEX™ Model GA Venting Systems listed

to UL1777 and ULCS635 manufactured by

Flexmaster Canada Limited.

Use only the correct size venting, 4 1/2 in.

(114 mm) inner and 7 1/2 in. (191 mm) outer.

These approved vent system components are

labeled for identiﬁcation. DO NOT use any

other manufacturer’s vent components with

these appliances.

TABLE OF CONTENTS

Packaging .........................................page 2

Introduction ......................................page 2

General Information ..........................page 2

Location ............................................page 4

Appliance and Vent Clearances ........page 4

Framing Speciﬁcations ...................... page 5

Facing Requirements ........................page 6

Hearth Requirements ........................page 7

Fireplace Speciﬁcations .....................page 8

Vent Termination Clearances ............ page 9

Typical Installation Sequence ...........page 9

Detailed Installation Steps ................. page 9

Step 1. Framing ............................... page 9

Step 2. Routing Gas Line ................page 11

Step 3. Install the Venting System ..page 11

Vertical Termination Systems ............ page 11

Vent Section Length Chart ................page 12

Vertical Vent Tables and Figures ........page 15

Horizontal Termination System .........page 16

Horizontal Vent Tables and Figures ...page 18

Venting Using Flexible Vent Pipe ....... page 20

Step 4. Field Wiring ......................... page 21

Step 5. Connecting Gas Line ...........page 21

Comfort Control Valve ....................... page 22

Step 6. Installing Ceramic Panels

And Logs ......................................page 24

Step 7. Checking Unit Operation .....page 24

Step 8. Installing Glass Door .......... page 24

Step 9. Burner Adjustments ............page 25

Finishing Requirements ....................page 26

Cold Climate Insulation .....................page 26

Step 10. Attaching Safety-in-

Operation Warnings .......................Page 28

Installation Accessories ....................page 29

Gas Conversion Kits .........................page 30

PACKAGING

The assembled Spectra direct vent gas ﬁreplace

heater is packaged with:

1 - one log set, located in the ﬁrebox.

2 - one envelope containing the literature

package (homeowner's manual,

installation instructions, log set

supplement, warning labels, and

warranty), located in the control

compartment.

3 - one bag of glowing embers, located in the

control compartment.

4 - one ceramic panel set, located on top

of unit.

5 - one hand-held remote control, located in

the control compartment.

6 - one cast iron suround (classic arch).

7 - one surround grill (black or nickel ﬁnish).

Each kit comes with an individual set of

installation instructions.

Please read and understand these

instructions before beginning your

installation.

INTRODUCTION

WARNING

Improper installation, adjust-

ment, alteration, service or

maintenance can cause injury

or property damage. Refer to

this manual. For assistance or

additional information consult

a qualified installer, service

agency or the gas supplier.

WARNING

Failure to comply with these

installation instructions will result

in an improperly installed and

operating appliance, voiding its

warranty. Any change to this appli-

ance and/or its operating controls

is dangerous.

WARNING

Clothing or other flammable

material should not be placed

on or near the appliance.

AVERTISSEMENT

On ne devrait pas placer de

vêtements ni d’autres matières

inﬂammables sur l’appareil ni à

proximité.

WARNING

Any safety screen or guard

removed for servicing the appli-

ance must be replaced prior to

operating the appliance.

AVERTISSEMENT

Tout écran ou protecteur retiré

pour permettre l’entretien de

l’appareil doit être remis en

place avant de mettre l’appareil

en marche.

Note: Installation and repair should be done

by a qualiﬁed service person. The appliance

should be inspected before use and at least

annually by a professional service person.

More frequent cleaning may be required

due to excessive lint from carpeting, bed-

ding material, etcetera. It is imperative

that control compartments, burners and

circulating air passageways of the appliance

be kept clean.

Remarque : L’installation et la réparation

devrait être conﬁées à un technicien qualiﬁé.

L’appareil devrait faire l’objet d’une inspec-

tion par un technicien professionnel avant

d’être utilisé et au moins une fois l’an par la

suite. Des nettoyages plus fréquents peuvent

être nécessaires si les tapis, la literie, et

cetera produisent une quantité importante de

pous-sière. Il est essentiel que les comparti-

ments abritant les commandes, les brûleurs et

les conduits de circulation d’air de l’appareil

soient tenus propres.

Do not use these appliances if any part

has been under water. Immediately call a

qualiﬁed, professional service technician

to inspect the appliance and to replace any

parts of the control system and any gas

control which have been under water.

Ne pas utiliser cet appareil s’il a été plongé,

même partiellement, dans l’eau. Ap-

peler un technicien qualiﬁé pour inspecter

l’appareil et remplacer toute partie du

système de commande et toute commande

qui a été plongée dans l’eau.

Only trim kit(s) supplied by the manufacturer

shall be used in the installation of this ap-

pliance.

Seules les trousses de garniture fournies

par le fabricant doivent être utilisées pour

l’installation de cet appareil.

These appliances comply with National Safety

Standards and are tested and listed by OMNI-Test

Laboratories, Inc. (Report No. 116-F-02b-5)

to ANSI Z21.88-2009/CSA 2.33-2009, and

CGA-2.17-M91 (R2009) in both USA and

Canada, as vented gas ﬁreplace heaters.

Both millivolt and electronic versions of

these appliances are listed by OMNI-Test

Laboratories for installation in bedrooms

and Manufactured Homes.

WARNING

Improper installation or use of

this appliance can cause serious

injury or death from ﬁre, burns,

explosions or carbon monoxide

poisoning.

Misc. Codes / Standards -

The Installation must conform to local codes or,

in the absence of local codes, with the National

Fuel Gas Code, ANSI Z223.1/NFPA 54 - latest

edition (In Canada, the current CAN/CSA-B149.1

installation code).

The appliance, when installed, must be electri-

cally grounded and wired in accordance with

local codes or, in the absence of local codes,

with the National Electrical Code, ANSI/NFPA

70 - latest edition, or the Canadian Electrical

Code, CSA C22.1 - latest edition.

Provide adequate clearances around air open-

ings and adequate accessibility clearance for

service and proper operation. Never obstruct the

front or back openings of the appliance.

These appliances are designed to operate on

natural or propane gas only. The use of other

fuels or combination of fuels will degrade

the performance of this system and may be

dangerous.

These ﬁreplaces are designed as supplemental

heaters. Therefore, it is advisable to have an

alternate primary heat source when installed in

a dwelling. Refer to Table 1 for efﬁciencies.

Efﬁciencies %

Models

Natural Gas Propane

P4* Steady

State

AFUE

P4* Steady

State

AFUE

LSS-35 51.6 73 70 53.6 73 71

LSS-40 58.8 73 70 61.7 73 71

Table 1

*Canadian Energuide Rating

**Annual Fuel Utilization Efﬁciency (AFUE) is the recognized U.S.

rating system for the total efﬁciency of heating products.

These electronic models come standard with a

mondulating gas valve; ﬂame appearance and

heat output can be controlled with the remote.

The BTU Input for these appliances is shown

in Table 2.

Table 2

Model Fuel Maximum

Input

(BTU/hr)

Minimum

Input

(BTU/hr)

LSS-35CN Natural

Gas 33,000 23,500

LSS-35CP Propane 30,000 23,500

LSS-40CN Natural

Gas 41,500 28,400

LSS-40CP Propane 37,000 30,700

4NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Test gauge connections are provided on the

front of the gas control valve (identiﬁed IN

for the inlet and OUT for the manifold side).

The control valves have a 3/8" (10mm) NPT

thread inlet and outlet side of the valve (see

Figure 1).

Propane tanks are at pressures that will cause

damage to valve components. Verify that the

tanks have step down regulators to reduce the

pressure to safe levels.

Manifold Gas Supply Pressure (all models)

Fuel # Low High

Natural

Gas

1.6 in.

(41 mm) WC

(0.40 kPa)

3.5 in.

(89 mm) WC

(0.87 kPa)

Propane 6.3 in.

(160 mm) WC

(1.57 kPa)

10.0 in.

(254 mm) WC

(2.49 kPa)

Table 4

Burner Oriﬁce Sizes

Elevation 0-4500 feet ( 0-1372 meters)

Model

Series Nat.Gas

drill size (inches) Propane

drill size (inches)

LSS-35

Rear Burner

#44 (0.086 in.

2.2 mm)*

60J80•

#55 (0.052 in.

1.3 mm)*

19L52•

LSS-35

Front Burner

#50 (0.070 in.

1.8 mm)*

H4873•

#61 (0.039 in.

1.0 mm)*

35M91•

LSS-40

Rear Burner

#42 (0.094 in.

2.4 mm)*

H3721•

(0.054 in.

1.4 mm)*

88J59•

LSS-40

Front Burner

#45 (0.082 in.

2.1 mm)*

39L66•

#56 (0.047 in.

1.2 mm)*

62L37•

Table 5

REQUIREMENTS FOR THE COMMON-

WEALTH OF MASSACHUSETTS

These ﬁreplaces are approved for installation in

the US state of Massachusetts if the following

additional requirements are met:

• Install this appliance in accordance with

Massachusetts Rules and Regulations 248

C.M.R.

• Installationandrepair mustbedoneby a

plumber or gas ﬁtter licensed in the Com-

monwealth of Massachusetts.

• Theexiblegas line connectorusedshall

not exceed 36 inches (92 centimeters) in

length.

• Theindividualmanualshut-offmustbea

T-handle type valve.

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, hori-

zontal terminations installed less than seven

(7) feet above the ﬁnished grade must comply

with the following additional requirements:

Inlet Gas Supply Pressure (all models)

Fuel # Minimum Maximum

Natural

Gas

4.5 in.

(114 mm) WC

(1.12 kPa)

10.5 in.

(267 mm) WC

(2.61 kPa)

Propane 11.0 in.

(279 mm) WC

(2.74 kPa)

13.0 in.

(330 mm) WC

(3.23 kPa)

Table 3

Gas Pressure - All Models

Tables 3 and 4 show the appliances' inlet and

manifold gas pressure requirements:

Gas Valve

Refer to Figure 1 for key gas valve features.

Oriﬁce Sizes - Sea Level to High Altitude

(All Models)

These appliances are tested and approved for

installation at elevations of 0-4500 feet (0-1372

meters) above sea level using the standard burner

oriﬁce sizes (marked with an "*" in Table 5).

For elevations above 4500 feet, contact your gas

supplier or qualiﬁed service technician .

Deration - At higher elevations, the amount

of BTU fuel value delivered must be reduced

by either:

•Usinggasthathasbeenderatedbythegas

company.

•Bychangingtheburneroricetoasmaller

size as regulated by the local authorities having

jurisdiction and by the (USA) National Fuel Gas

Code NFPA 54/ANSI Z223.1 - latest edition or,

in Canada, the CAN/CSA-B149.1 codes - latest

edition.

Install the appliance according to the regulations

of the local authorities having jurisdiction and,

in the USA, the National Fuel Gas Code NFPA

54 / ANSI Z223.1 - latest edition or, in Canada,

the CAN/CSA-B149.1 - latest edition.

Flame breadth, height and width will diminish

4% for every 1,000 feet of altitude.

These appliances must be isolated from the

gas supply piping system (by closing their

individual manual shut-off valve) during any

pressure testing of the gas supply piping

system at test pressures equal to or less

than 1/2 psig (3.5 kPa).

These appliances and their individual shut-off

valves must be disconnected from the gas

supply piping system during any pressure

testing of that system at pressures greater

than 1/2 psig (3.5 kPa).

These appliances must not be connected to a

chimney or ﬂue serving a separate solid fuel

burning appliance.

Figure 1 SIT Proﬂame Valve

Orange Wire

(From DFC Wire

Harness)

Pressure

Regulator

Tower

Yellow Ground Wire

(From DFC Wire

Harness)

Green Wire

(From DFC Wire

Harness)

Line (In) Test Port

Manifold (Out)

Test Port

Connect GTMS

Wire Harness

* Standard size installed at factory

• Part /Cat. Number

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

• A hard wired carbon monoxide detector

with an alarm and battery back-up must be

installed on the ﬂoor level where the gas

ﬁreplace is installed. The carbon monoxide

detector must comply with NFPA 720, be

ANSI/UL 2034 listed and be ISA certiﬁed.

• Ametalorplasticidenticationplatemustbe

permanently mounted to the exterior of the

building at a minimum height of 8 ft (2.4 m)

above grade and be directly in line with the

horizontal termination. The sign must read,

in print size no less than 1/2 in. (13 mm) in

size, GAS VENT DIRECTLY BELOW. KEEP

CLEAR OF ALL OBSTRUCTIONS.

NEW YORK CITY, NEW YORK (MEA)

Installation of these ﬁreplaces are approved

for installation in New York City in the US state

of New York.

COLD CLIMATE INSULATION

For cold climate installations, seal all cracks

around your appliance with noncombustible

material and wherever cold air could enter

the room. It is especially important to insulate

outside chase cavity between studs and under

ﬂoor on which appliance rests, if ﬂoor is above

ground level. Gas line holes and other open-

ings should be caulked or stuffed with unfaced

ﬁberglass insulation.

If the ﬁreplace is being installed on a cement

slab in cold climates, a sheet of plywood or

other raised platform can be placed underneath

to prevent conduction of cold transferring to

the ﬁreplace and into the room. It also helps to

sheetrock inside surfaces and tape for maximum

air tightness and caulk ﬁrestops.

MANUFACTURED HOME

REQUIREMENTS

This appliance may be installed in an aftermar-

ket permanently located, manufactured home

and must be installed in accordance with the

manufacturer's instructions and the Manufac-

tured Home Construction and Safety Standard,

Title 24 CFR, Part 3280, in the United States, or

the Standard for Installation in Mobile Homes,

CAN/CSA Z240 MH Series, in Canada.

Cet appareil peut être installé cómme du matéri-

el d'origine dans une maison préfabriquée (É.U.

seulement) ou mobile et doit être installé selon

les instructions du fabricant et conformément

à la norme Manufactured Home Constructions

and Safety, Title 24 CFR, Part 3200 aux Unis ou

à la norme Can/CSA-Z240 Série MM, Maisons

mobiles au Canada.

Figure 2 - Typical Locations

NOITACILPPA TNEVPOT

APPLICATION

TOP VENT

TNEVPOT NOITACILPPA

RECESSED

INSTALLATION

TOP VENT

APPLICATION

NOITACILPPA

TNEVPOT

NOITACILPPA

TNEVPOT

HORIZONTAL VENT

(Top Vent Application)

VERTICAL VENT

(Top Vent Application)

Note: When the unit is installed with one

side ﬂush with a wall, the wall on the other

side of the unit must not extend beyond the

front edge of the unit.

LOCATION

In selecting the location, the aesthetic and

functional use of the appliance are primary

concerns. However, vent system routing to

the exterior and access to the fuel supply are

also important.

Due to high temperatures, the appliance

should be located out of trafﬁc and away from

furniture and draperies (Figure 2).

En raison des températures élevées, l’appareil

devrait être installé dans un endroit où il y a

peu de circulation et loin du mobilier et des

tentures (Figure 2).

The location should also be free of electrical,

plumbing or other heating/air conditioning

ducting.

These direct-vent appliances are uniquely

suited for installations requiring a utility shelf

positioned directly above the ﬁreplace. Utility

shelves like these are commonly used for locat-

ing television sets and decorative plants.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is

not convertible for use with other gases, unless

a certiﬁed kit is used.

Cet appareil doit être utilisé uniquement avec le

type de gaz indiqué sur la plaque signalétique.

Cet appareil ne peut être converti à d'autres gaz,

sauf si une trousse de conversion est utilisée.

CAUTION: Ensure that the cross mem-

bers are not cut or weakened during

installation. The structural integrity of

the manufactured home ﬂoor, wall, and

ceiling / roof must be maintained.

CAUTION: This appliance must be ground-

ed to the chassis of the manufactured

home in accordance with local codes or

in the absence of local codes, with the

National Electrical Code ANSI / NFPA 70

- latest edition or the Canadian Electrical

Code CSA C22.1 - latest edition.

Drywall

Mantel

Non-Combustible

Top Of

Fireplace Opening

6NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Roof Pitch is X/12

2 FT

MIN.

2 FT MIN.

Lowest

Discharge

Opening

*H = MINIMUM HEIGHT FROM ROOF TO

LOWEST DISCHARGE OPENING OF VENT

TERMINATION HEIGHTS FOR VENTS ABOVE

FLAT OR SLOPED ROOFS

Horizontal Overhang

Vertical

Wall

Vent

Termination

Storm Collar

Concentric

Vent Pipe

Flashing

1 inch (25.4 mm) Minimum

Clearance to Combustibles

Figure 4

Vertical Vent Termination Clearances

VENT TERMINATION CLEARANCES

These instructions should be used as a

guideline and do not supersede local codes

in any way. Install venting according to local

codes, these instructions, the current National

Fuel Gas Code (ANSI-Z223.1) in the USA or

the current standards of CAN/CSA-B149.1

in Canada.

Vertical Vent Termination Clearances

Terminate multiple vent terminations according

to the installation codes listed above. Also see

Figure 3.

Terminate single vent caps relative to building

components according to Figure 4.

Note - See Figure 33 on Page 19 for the exterior wall recess

allowances of the square horizontal termination.

Termination Heights For Vents

Above Flat Or Sloped Roofs

Ref. NFPA 54 / ANSI Z223.1

Roof Pitch * Feet * Meters

Flat to 6/12 1.0 0.3

6/12 to 7/12 1.25 0.38

7/12 to 8/12 1.5 0.46

8/12 to 9/12 2.0 0.61

9/12 to 10/12 2.5 0.76

10/12 to 11/12 3.25 0.99

11/12 to 12/12 4.0 1.22

12/12 to 14/12 5.0 1.52

14/12 to 16/12 6.0 1.83

16/12 to 18/12 7.0 2.13

18/12 to 20/12 7.5 2.29

20/12 to 21/12 8.0 2.44

The vent / air intake termination clearances

above the high side of an angled roof is as

shown in the following chart:

Figure 5

(152 mm)

12"

(305 mm)

Combustible Projection greater

Horizontal Vent Termination Clearances

Combustible Projection

2-1/2 inches or less in length

18"

(457 mm)

Ventilated

Soffit Unventilated

Soffit

than 2-1/2 inches in length

Termination Kit

Side Elevation View

Termination Kit

All horizontal terminations

may be located as close as

6” (152mm) to any

(non-combustible and

combustible) exterior

sidewall. This distance

may be decreased to 2”

(51mm) for non--

combustible exterior

sidewalls only, if the

SV4.5HT-2 termination

is used.

Horizontal Vent Termination Clearances

The horizontal vent termination must have a minimum of 6" (152 mm) clearance to any overhead

combustible projection of 2-1/2" (64 mm) or less (see Figure 5). For projections exceeding 2-1/2"

(64 mm), see Figure 5. For additional vent location restrictions refer to Figure 6 on Page 7.

12”

(305mm)

Minimum

Figure 3 - Multiple Terminations

Be aware that this is a heat producing ap-

pliance. Objects placed above the unit are

exposed to elevated temperatures.

Do not insulate the space between the appli-

ance and the area above it (see Figure 7 ).

The minimum height from the base of the appli-

ance to the underside of combustible materials

used to construct a utility shelf in this fashion

is shown in Figure 7.

The appliance should be mounted on a fully

supported base extending the full width and

depth of the unit. The appliance may be located

on or near conventional construction materials.

However, if installed on combustible materials,

such as carpeting, vinyl tile, etc., a metal or

wood barrier covering the entire bottom surface

must be used.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

EXTERIOR HORIZONTAL VENT TERMINATION CLEARANCE REQUIREMENTS

Figure 6

Fixed

Closed

Window

Operable

Window

= Area where Termination is not Permitted

= Air Supply Inlet

X= Vent Termination

3 ft.

= 9 in. (229 mm) in U.S.

= 12 in. (305 mm)

in Canada

Inside

Corner Detail

*18 in. (457 mm)

Ventilated Soffit

Horizontal

Termination

Detail D

Exterior Wall

6 in. (152 mm)

Inside Corner

* See Item D in the Text Below.

NOTE: Local Codes Or Regulations

May Require Different Clearances.

NOTE: Location Of The Vent Termination

Must Not Interfere With Access To The

Electrical Service.

*noitallatsnInaidanaC**noitallatsnISU

.ynoclabro,kced,hcrop,adnarev,edargevobaecnaraelC=A *)mc03(sehcni21**)mc03(sehcni21

.denepoebyamtahtroodrowodniwotecnaraelC=B secnailpparof)mc51(sehcni6

)mc03(sehcni21,)Wk3(hutB000,01<

)Wk3(hutB000,01>secnailpparof

secnailpparof)mc51(sehcni6

)mc32(sehcni9,)Wk3(hutB000,01<

dna)Wk3(hutB000,01>secnailpparof

)mc03(sehcni21,)Wk51(hutB000,05<

**)Wk51(hutB000,05>secnailpparof

wodn

iwdesolcyltnenamrepotecnaraelC=C otdednemmocer)mm503(sehcni21

noitasnednocwodniwtneverp

otdednemmocer)mm922(sehcni9

noitasnednocwodniwtneverp

ehtevobadetacoltiffosdetalitnevotecnaraelclacitreV=D

)mm854(sehcni81foecnatsidlatnozirohanihtiwnoitanimret

noitanimretehtfoenilretnecehtmorf

)mm854(sehcni81)mm854(sehcni81

***tiffosdetalitnevnuotecnaraelC=E )mm503(sehcni21)mm503(sehcni21

renrocedistuootecnaraelC=F muminim

)mc7.21(sehcni5muminim)mc7.21(sehcni5

renrocedisniotecnaraelC=G 2-TH5.4VS-muminim)mc80.5(sehcni2 2-TH5.4VS-muminim)mc80.5(sehcni2

evobadednetxeenilretnecfoedisnihcaeotecnaraelC=H

ylbmessarotaluger/retem

teef51fothgiehanihtiw)mc19(teef3

*ylbmessarotaluger/retemehtevoba

teef51fothgiehanihtiw)mc19(teef3

**ylbmessarotaluger/retemehtevoba

teltuotnevrotalugerecivresotecnaraelC=I *)mc19(teef3**)mc19(teef3

rognidliubot

telniylppusrialacinahcemnonotecnaraelC=J

ecnailpparehtoynaottelnirianoitsubmoceht

secnailpparof)mc51(sehcni6

)mc03(sehcni21,)Wk3(hutB000,01<

)Wk3(hutB000,01>secnailpparof

secnailpparof)mc51(sehcni6

)mc32(sehcni9,)Wk3(hutB000,01<

dna)Wk3(hutB000,01>secnailpparof

)mc03(sehcni21,)Wk51(hutB000,05<

**)Wk51(hutB000,05>secnailpparof

telniylppusrialacinahcemaotecnaraelC=K *)m38.1(teef6 teef01nihtiwfievoba)mc19(teef3

*yllatnoziroh)m3(

detacolyaweviddevaproklawedisdevapevobaecnaraelC=L

ytreporpcilbupno

‡)m31.2(teef7‡)m31.2(teef7

ynoclabrokced,hcrop,adnarevrednuecnaraelC=M ‡*)mc03(sehcni21‡)mc03(sehcni21

)mumixaM(evoclAfohtpeD=N *)m38.1(teef6**)m38.1(teef6

)evoclA(noitanimreTotecnaraelC=O *)mm2.51(sehcni6**)mm2.51(sehcni6

)muminiM(evoclAfohtdiW=P *)mc19(teef3*)mc19(teef3

)evoclA(evobAelbitsubmoCotecnaraelC=Q *)mm754(sehcni81**)mm7

54(sehcni81

.edoCnoitallatsnIenaporPdnAsaGlanoitaN1.941B-ASCtnerrucehthtiwecnadroccanI*

.sedoCsaGleuFlanoitaN45APFN/1.322ZSISNAtnerucehthtiwecnadroccanI**

.muminim)mc67(sehcni03-lairetamtiffoslynivotderiuqerecnaraelC***

htobsevresdnasgnillewdylimafelgnisowtneewtebdetacolsihcihwyawevirddevaproklawedisaevobayltceridetanimrettonllahstnevA‡

.sgnillewd

.roolfehthtaenebsedis2muminimanonepoyllufsiynoclabrokced

,hcrop,adnarevfidettimrepylnO‡*

NOTE: Clearances are in accordance with local installation codes and the requirements of the gas supplier.

8NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

5(127)

8-1/4

(209)

(356)

12 (305)

17 (431)

(51)

(102)

(152)

(203)

(254)

(305)

18 (457)

22 (559)

26 (660)

24 (610)

20 (508)

Top Of

Fireplace

Opening

16 (406)

inches (millimeters)

Mantel Depth

Figure 8 - Minimum Mantel Clearances

Figure 9 - Minimum Distance to Unprotected Side Wall

Top View of

Fireplace

45o

Protected wall shown in white

Inches (millimeters)

MINIMUM CLEARANCES TO COMBUSTIBLES

Appliance And Vent Clearances

The appliance is approved with zero clearance to combustible materials on

all sides (as detailed in Table 6 ), with the following exception: When the

unit is installed with one side ﬂush with a wall, the wall on the other

side of the unit must not extend beyond the front edge of the unit. In

addition, when the unit is recessed, the side walls surrounding the unit

must not extend beyond the front edge of the unit (see Figure 2).

*Note: 3 in. (76 mm) above any horizontal/inclined vent component.

**Note: See Page 9, Step 1 for clearance requirements to the nailing

ﬂange located at each side of the unit and any screw heads adjacent

to it.

Hearth Extension - A hearth extension is not required with this appliance.

If a hearth extension is used, do not block the lower control compartment

door. Any hearth extension used is for appearance only and does not have

to conform to standard hearth extension installation requirements.

Shelf Height - To provide for the lowest possible shelf surface, the venting

attached to the top vent should be routed in a way to minimize obstructions

to the space above the appliance. Do not insulate the space between the

appliance and the area above it (see Figure 7). The minimum height from

the base of the appliance to the underside of combustible materials used

to construct a utility shelf in this fashion is shown in Figure 7.

Wall Finishes / Surrounds / Mantels

Note: Combustible wall finish materials and/or surround materials

must not be allowed to en-croach the area defined by the appliance

front face (black sheet metal). Never allow combustible materials

to be positioned in front of or overlapping the appliance face (see

Figure 9 and Figure 50 on Page 34).

Non-combustible materials, such as surrounds and other appliance trim,

may be installed on the appliance face with these exceptions: they must

not cover any portion of the removable glass panel.

Vertical installation clearances to combustible mantels vary accord-

ing to the depth of the mantel. See Figure 8. Mantels constructed of

non-combustible materials may be installed at any height above the

appliance opening; however, do not allow anything to hang below the

ﬁreplace hood.

Combustible materials may

project beyond one side

of the fireplace opening

as long as they are kept

within the shaded areas

illustrated here.

Combustible Materials

Allowed In Shaded Area

“Safe Zone”

Combustible Walls

shown in dark gray

At 14 in. (356 mm)

minimum side

wall clearance, a

combustible wall

can project to any

length.

At 8 1/4 in. (210 mm)

side wall clearance,

a combustible wall

can project 12 in.

(305 mm).

Figure 7 -

Shelf Height Minimum Clearances With Top Venting

MINIMUM CLEARANCES* Inches (millimeters)

Back 1/2 in. (13) to wrapper

0 (0) to Spacers

Sides 1/2 in. (13) to wrapper

0 (0) to Spacers **

Top Spacers 0 (0)

Floor 0 (0)

From Bottom of Unit To Ceiling 64 (1626)

Vent 3 (76) Top* / 1 (25.4) Sides & Bottom

SERVICE CLEARANCES Feet (meters)

Front 3 feet (0.9 meters)

Table 6

.oNledoM )mm(sehcnithgieHflehS

woblEeergeD09enOhtiw-tneVpoT

tneVeruce

elFeruceS

53-SSL 2/175)1641

/19

5051(

04-SSL )9941(9

3451(4/306

Shelf Height

(

see table)

Do not insulate the

space between the

appliance and the

area above it.

Shelf Above Fireplace With Top Venting

12-1/4 in.

(311mm)

*Note: For Secure Vent

A SV4.5L6 6 in. (152 mm) Section

(Cat. No. 77L70) Is Required.

*See Note

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 10

FIREPLACE FRAMING SPECIFICATIONS

(178)

(308)

(

267

)

VENT FRAMING -

TOP VENT WITH ONE

6 SECTION AND

ONE 90¡ ELBOW

Framing should be constructed

of 2x4 or larger lumber.

Inches (mm)

(130)

**FRAMING WITH SQUARE HORIZONTAL TERMINATIONS (SV4.5HT)

** See the horizontal venting Figures 29 and 30 on page 17 for

restrictions on the use of the square termination (SV4.5HT).

NOTE: For Secure Vent A 6 Section

SV4.5L6 (Cat. No. 77L70) Is Required

Before Installing The 90 Degree Elbow.

5-1/8

12-1/8

10-1/2

20-13/16

1/2

ledoM

.oN ABCD E

53-SSL .ni538/161/5268/1938/16361/1151

mm2983851499819004

04-SSL .ni8/10461/5768/5748/58361/771

mm220101710121189344

Back wall of chase/enclosure

(including any finishing materials)

Note-

Venting requirements for corner installations -

ledoM

.oN

ABC

53-SSL .ni538/18/52

/115

mm298380

921

04-SSL .ni8/10

/14

/525

mm2201121

331

Framing Dimensions

Figure 11 Corner Framing with Square Termination (SV4.5HT)

10 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FACING REQUIREMENTS

Figure 13 Non-Combustible Requirements

Unit Nailing Flange

(On Both Sides)

Cast Iron Facade

Fireplace

TOP VIEW

1/2 in. (13 mm) Drywall

3/8 in. (10 mm)

Tile

1/2 in. (13 mm)

Concrete Board

2 x 4 in.

(51 x 102 mm)

9 in.

(229 mm)

Min.

Requires A Concrete Board

(Or Other Non-Combustible

Material) Extending From

The Top Of The Fireplace To

The Floor And To The

Framing Members On Both

Sides. Do Not Use

Sheetrock, Plywood Or Other

Combustible Material

4 1/2 in. (114 mm) Min.

(Both Sides)

Top Of Fireplace

Behind Cement Board Combustible Facing Materials May

Be Used Above This Point

Warning: Fire Hazard: Do Not

Place Any Combustible Material

Over The Fireplace Opening.

Glass Door Accessibility: Any

Non-Combustible Finishing

Material That Protrudes More

Than 1 in. (25 mm) From The

Facing Must Maintain A 9 in.

(229 mm) Clearance From The

Fireplace Opening. For

Combustible Material, Refer

To Figure 9 On Page 8.

Top Of Fireplace Opening

10 in.

(254 mm)

Figure 12

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

HEARTH REQUIREMENTS

Figure 14

Cement Board

Tile, Marble, Brick, Carpet,

Or Other Non-Combustible

Or Combustible Material

Fireplace

Stand

1 in. (25 mm)

Min.

Figure 15 RAISED FIREPLACE

Fireplace

Floor Plywood Platform

Face

Thickness Of the Floor Covering

(Carpet, Flooring, Etc.)

1 in. (25 mm) Min.

12 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

FIREPLACE SPECIFICATIONS

ELECTRICAL

INLET

Dimensions In Inches (mm)

* Includes The 1/2 in. (13 mm) Spacers

1 (25.4)

3 (76)

11-1/4

(286) G

1/2 (13) Spacers

8-11/32

(211)

(25.4)

3 (76)

GAS INLET

(BOTH SIDES)

*21-3/8

(543)

(152) 8-13/16

(225)

2-9/16

(65)

(76)

FRAMING SPACERS

CONCENTRIC FLUE

Combustion Air - 7-1/2 (190)

Flue - 4-1/2 (114)

3 (76)

Vent Restrictor

Adjustment Rod

ledoM

.oN ABCD EFGH

53-SSL .ni8/38361/1532/1929161/3618/3132/1124/301

mm579198947384114797645372

04-SSL .ni8/79361/1042/1432/10261/3128/7232/1624/131

mm31018101678125835538376733

Figure 16

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

DETAILED INSTALLATION STEPS

The appliance is shipped with all gas controls and

components installed and pre-wired. Remove

the shipping carton, exposing the front glass

door. Remove ceramic panel kit from the top of

the ﬁreplace and set it aside with care. Remove

the cardboard from underneath the pressure

relief plates. Open the two latches (located

under the ﬁrebox ﬂoor) securing the glass

door. Remove the door by tilting it outward at

the bottom and lifting it up. Set the door aside

protecting it from inadvertent damage. See

Figure 48 on page 27.

TYPICAL INSTALLATION SEQUENCE

The typical sequence of installation follows,

however, each installation is unique resulting

in variations to those described.

See the page numbers references in the follow-

ing steps for detailed procedures.

Step 1. (page 13) Construct the appliance fram-

ing. Position the appliance within the framing

and secure with nailing brackets.

Step 2. (page 13) Route gas supply line to

appliance location.

Step 3. (page 13) Install the vent system and

exterior termination.

Step 4. (page 23) Field Wiring

Install the operating control switch (not factory

provided) and bring in electrical service line for

forced air circulating blower.

Step 5. (page 23) Make connection to gas

supply.

Step 6. (page 26) Install the ceramic panel,

logs, and glowing embers.

Step 7. (page 26) Checkout appliance opera-

tion.

Step 8. (page 26) Install glass door frame

assembly.

Step 9. (page 27) Adjust burner to ensure

proper ﬂame appearance.

Step 10. (page 28) Afﬁx warning labels.

Step 1. FRAMING

Frame these appliances as illustrated in

Figure 10 on page 9, unless the appliance is to

be installed in a corner. See Figure 11 on page

9 for corner framing installations. All framing

details must allow for a minimum clearance to

combustible framing members as shown in

Table 6 on page 8.

See Figure 12 on page 10 for the facing detail.

See Figure 13 on page 10 for the Non-Com-

bustible requirements. See Figures 14 and 15

on page 11 for Hearth Requirements.

Right Side

Front Corner of

Fireplace Framing

6 in.

(152 mm)

3 in.

(76 mm)

Figure 17

Step 3. INSTALL THE VENT SYSTEM

General Information

These instructions should be used as a

guideline and do not supersede local codes

in any way. Install vent according to local

codes, these instructions, the current

National Fuel Gas Code (ANSI-Z223.1) in

the USA or the current standards of CAN/

CGA-B149.1 and -B149.2 in Canada.

These ﬁreplaces are designed, tested

and listed for operation and installation

with, and only with, Secure Vent™

Direct Vent System Components,

Secure Flex™ Flexible Vent

Components manufactured by Security

Chimneys International and Z-FLEX™

Model GA Venting Systems listed to

UL1777 and ULCS635 manufactured by

Flexmaster Canada Limited.

NOTE: The ﬂow of combustion and

ventilation air must not be obstructed.

These approved vent system components

are labeled for identiﬁcation. DO NOT

use any other manufacturer's vent

components with these appliances.

Some local jurisdictions may require the gap

between the outer wall of the vent system and

the ﬁrestop penetration opening to be sealed.

This is not a requirement of the listing of this

product, however this gap may be sealed using

aluminized tape or similar non-combustible

material.

The vent system may not service multiple

appliances, and must never be connected to a

ﬂue serving a solid fuel burning appliance. The

vent pipe is tested to be run inside an enclosing

wall (such as a chase). There is no requirement

for inspection openings in the enclosing wall at

any of the joints in the vent pipe.

Select Venting System - Horizontal or Vertical

With the appliance secured in framing, de-

termine vent routing and identify the exterior

termination location. The following sections

describe vertical (roof) and horizontal (exterior

wall) vent applications. Refer to the section

relating to your installation. A list of approved

venting components is shown in the two tables

on page 29.

VERTICAL TERMINATION SYSTEMS (ROOF)

Figure 18, and Figures 28 through 30

on pages 14 and 17 and their associated

Vertical Vent Tables illustrate the various verti-

cal venting conﬁgurations that are possible for

use with these appliances. Secure Vent pipe

applications are shown in these ﬁgures; Secure

Flex pipe may also be used. A Vertical Vent

Table summarizes each system’s minimum and

maximum vertical and horizontal length values

that can be used to design and install the vent

components in a variety of applications.

Both these vertical vent systems terminate

through the roof. The minimum vent height

above the roof and/or adjacent walls is speci-

ﬁed in ANSI Z223.1-(latest edition) (In Canada,

the current CAN-1 B149 installation code) by

major building codes. Always consult your lo-

cal codes for speciﬁc requirements. A general

guide to follow is the Gas Vent Rule (refer to

Figure 4 on page 6).

Step 2. ROUTING GAS LINE

Route a 1/2 in. (13 mm) gas line along the inside

of the right side framing as shown in Figure 17.

Gas lines must be routed, constructed and made

of materials that are in strict accordance with

local codes and regulations.

All appliances are factory-equipped with a

ﬂexible gas line connector and 1/2 in. (13 mm)

shutoff valve. (See step 5 on page 23).

14 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 18

Vertical (Offset) Installation

Analyze the vent routing and determine the

quantities of vent sections and number of el-

bows required. Refer to Vertical Vent Figures

and Tables on page 17 to select the type of

vertical installation desired. Vent sections are

available in net lengths of 4-1/2" (114 mm),

10-1/2" (267 mm), 22-1/2" (572 mm), 34-1/2"

(876 mm) and 46-1/2" (1181 mm). Refer to the

Vent Section Length Chart on this page for an

aid in selecting length combinations. Elbows are

available in 90° and 45° conﬁgurations. Refer

to Figure 23 for the SV4.5E45 and SV4.5E90

elbow dimensional speciﬁcations.

Vertical (Straight) Installation

Determine the number of straight vent sections

required. 4-1/2" (114 mm), 10-1/2" (267 mm),

22-1/2" (572 mm), 34-1/2" (876 mm) and

46-1/2" (1181 mm) net section lengths are

available. Plan the vent lengths so that a joint

does not occur at the intersection of ceiling or

roof joists. Refer to the Vent Section Length

Chart on this page.

SV4.5CGV-1

Termination SV4.5FA OR

SV4.5FB Flashing

AND SV4.5SC

STORM COLLAR

*SV4.5VF

Firestop/Spacer

SV4.5L6/12/24/36/48

Vent Sections

60 ft (18.3 m) Max

8 ft (2.4 m) Min

1" (25.4 mm)

Minimum

Clearance to

Combustibles

*When using Secure Flex,

use Firestop/Spacer

SF4.5VF

Note: Convert inches into metric equivalent

measurement, as follows:

Millimeters (mm) = Inches x 25.4

Centimeters (cm) = Inches x 2.54

Meters (M) = Inches x .0254

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 621426384T

noitceSteN )sehcni(htgneL 2/1-42/1-012/1-222/1-432/1-64

tneVfothgieHsnoitceStneVforebmuN

sehcnitf

67232000808

97252.32000066

5.082573.32100809

5.982521.42010067

5.103521.52001067

5.013578.52000909

5.523521.72000077

0335.72100078

54357.82000 01001

5.943521.92100 01011

27313000088

5.973526.13000 11011

5.814578.43000099

56457.8300000101

5.574526.9301000111

0840411000111

2941410100121

5.994526.1400010111

4052410010121

5.115526.2400001111

5.025573.3402011141

13552.4

402201151

5.835578.4410021141

94557.5410211151

8555.6400002121

5.265578.6410002131

5.865573.7401002131

37557.7411002141

5.085573.8400102131

5.985521.9401220151

5.595526.9411102151

5.406573.0500003131

51652.1501003141

5.526521.2502003151

5.136526.2510103151

5.736521.3501103151

15652.4500004141

5.556526.4510004151

2766502004161

8765.6510104161

5.886573.7511104171

5.796521.8500005151

2075.8510005161

5.217573.9511005171

0270600105161

TRAHCHTGNELNOITCESTNEV

lanimoN htgneLnoitceS )sehcni( 621426384T

noitceSteN )sehcni(htgneL 2/1-42/1-012/1-222/1-432/1-64

tneVfothgieHsnoitceStneVforebmuN

sehcnitf

5.4573.0100001

957.0200002

5.01578.0010001

5152.1110002

5.22578.1001001

5.13526.2030003

5.43578.2000101

5.73521.3111003

5.34526.3021003

5457.3002002

5.64578.3000011

1552.4100012

5.55526.4012003

7557.4001102

5.76526.5003003

9657.5000202

5.37521.6100203

5.97526.6010203

1857.6000112

5.19526.7002013

3957.7000022

5.79521.8100023

5.30152

6.8000303

801910 0304

71157.9105006

5.811578.9110305

6215.01001304

5.031578.01101305

53152.11006006

5.931526.11000033

5.241578.11100405

44121100034

5.451578.21110035

5.061573.31020035

5.271573.41000505

77157.41100506

6815.51000044

5.691573.61010045

70252.71000606

5.112526.71100607

5.712521.81010607

5.922521.91001607

5.232573.91000055

5.142521.02000707

6425.02100708

25212010708

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 22

Support Straps

(Plumber’s tape)

8 feet (2.4 m)

Maximum

Blocking

Figure 21

Figure 20

Figure 19

B. Attach vent components to appliance

- Secure Vent SV4.5 direct vent system compo-

nents are unitized concentric pipe components

featuring positive twist lock connections (see

Figure 20 ).

All of the appliances covered in this document

are ﬁtted with collars having locking inclined

channels. The dimpled end of the vent com-

ponents ﬁt over the appliance collar to create

the positive twist lock connection.

First Vent

Component

Align the dimple (four places)

with the opening of the locking

incline channel on appliance

collar. Twist vent component

clockwise to engage and seal.

Locking

Incline Channel

Dimple

Appliance collar

Vent / Appliance Collar

Connection

Align the dimple (four places) of the

upper vent section with the opening of

the locking incline channel on the

lower vent section. Twist vent

component clockwise to engage and

seal until arrow and dimple align.

Locking

Incline Channel

Dimple

Arrow

Connected

Vent Sections

Vent / Vent Section

Connection

Arrow

To attach a vent component to the appliance

collar, align the dimpled end over the collar,

adjusting the radial alignment until the four

locking dimples are aligned with the inlet of

the four inclined channels on the collar (refer to

Figure 20 ). Push the vent component against

the collar until it fully engages, then twist the

component clockwise, running the dimples

down and along the incline channels until they

seat at the end of the channels.

The unitized design of the Secure Vent

components will engage and seal both the inner

and outer pipe without the need for sealant or

screws. If desired, a #6 x 1/2 in. (13 mm) screw

may be used at the joint, but is not required as

the pipe will securely lock when twisted.

C. Attach vent components to each other -

Other vent sections may be added to the

previously installed section in accordance with

the requirements of the vertical vent ﬁgures and

tables. To add another vent component to a

length of vent run, align the dimpled end over the

inclined channel end of the previously installed

section, adjusting the radial alignment until the

four locking dimples are aligned with the inlets of

the four incline channels of the previous section.

10-1/2” Min.

(267 mm)

10-1/2” Min.

(267 mm)

Push the vent component against the previous

section until it fully engages, then twist the

component clockwise running the dimples down

and along the incline channels until they seat at

the end of the channels. This seating position

is indicated by the alignment of the arrow and

dimple as shown in Figure 21.

D. Install ﬁrestop/spacer at ceiling - When

using Secure Vent, use SV4.5VF ﬁrestop/spacer

at ceiling joists; when using Secure Flex, use

SF4.5VF ﬁrestop/spacer. If there is living space

above the ceiling level, the ﬁrestop/spacer

must be installed on the bottom side of the

ceiling. If attic space is above the ceiling, the

ﬁrestop/spacer must be installed on the top side

of the joist. Route the vent sections through the

framed opening and secure the ﬁrestop/spacer

with 8d nails or other appropriate fasteners at

each corner.

Remember to maintain 1" (25 mm) clearance

to combustibles, framing members, and attic

or ceiling insulation when running vertical

chimney sections.

E. Support the vertical vent run sections

-Support the vertical portion of the venting

system every 8 feet (2.4m) above the ﬁreplace

vent outlet using ﬁeld provided support straps

(conventional plumber's tape). Secure the

plumber's tape to the framing members with

nails or screws.

Loop the tape around the vent, securing the

ends of the tape to the framing. If desired, sheet

metal screws #6 x 1/2 in. (13 mm) length may

be used to secure the support straps to the vent

pipe . See Figure 22.

Where required, a telescopic vent section

(SV4.5LA) may be used to provide the installer

with an option in installing in tight and conﬁned

spaces or where the vent run made up of ﬁxed

length pieces develops a joint in a undesirable

location, or will not build up to the required

length. The SV4.5LA Telescopic Vent Section

has an effective length of from 1-1/2" (38 mm)

to 7-1/2" (191 mm). The SV4.5LA is ﬁtted with

a locking inclined channel end (identical to a

normal vent section component) and a plain end

with 3 pilot holes. Slip the plain end over the

locking channel end of a standard SV4.5 vent

component the required distance and secure

with three screws.

Maintain a minimum 1" (25 mm) clearance to

combustible materials for all vertical elements.

Clearances for all horizontal elements are 3"

(76 mm) on top, 1" (25 mm) on sides and 1"

(25 mm) on the bottom.

A. Frame ceiling opening - Use a plumb line

from the ceiling above the appliance to locate

center of the vertical run. Cut and/or frame an

opening, 10-1/2" x 10-1/2" (267mm x 267mm)

inside dimensions, about this center mark

(Figure 19 ).

16 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 24

Figure 25

Figure 27

Figure 26

K. Install the vertical termination - The ﬁnal

step involves installation of the SV4.5CGV-1

Vertical Termination. Extend the vent sections

to the height as shown in the "Vertical vent

termination section" in Figure 4 on page 6. The

SV4.5CGV-1 Vertical Termination (Figure 27 )

installs in the exact same fashion as any other

Secure Vent section. Align the termination

over the end of the previously installed section,

adjusting the radial alignment until the locking

dimples of the termination are aligned with

the inlets of the four incline channels of the

last vent section. Push the termination down

until it fully engages, then twist the termination

clockwise running the dimples down and along

the incline channels until they seat at the end

of the channels.

I. Install the roof ﬂashing - Extend the vent sec-

tions through the roof structure. Install the roof

ﬂashing over the vent section and position such

that the vent column rises vertically (use carpen-

ters level) (Figure 25 ). Nail along perimeter to

secure ﬂashing or adjust rooﬁng to overlap the

ﬂashing edges at top and sides only and trim

where necessary. Seal the top and both sides of

the ﬂashing with waterproof caulking.

If the vent system extends more than 5' (1.5

m) above the roof ﬂashing, stabilizers may be

necessary. Additional screws may be used at

section joints for added stability. Guide wires

may be attached to the joint for additional sup-

port on multiple joint conﬁgurations.

G. Continue installation of horizontal/inclined

sections - Continue with the installation of the

straight vent sections in horizontal/inclined run

as described in Step C. Install support straps

every 5 ft (1.52 m) along horizontal/inclined

vent runs using conventional plumber’s tape. It

is very important that the horizontal/inclined

run be maintained in a straight (no dips) and

recommended to be in a slightly elevated

plane, in a direction away from the ﬁreplace

of 1/4 in. rise per foot (20 mm per meter) which

is ideal, though rise per foot run ratios that are

smaller are acceptable all the way down to at or

near level. Use a carpenter’s level to measure

from a constant surface and adjust the support

straps as necessary.

It is important to maintain the required clear-

ances to combustibles: 1" (25 mm) at all sides

for all vertical runs; and 3" (76 mm) at the top,

1" (25 mm) at sides, and 1" (25 mm) at the

bottom for all horizontal/inclined runs.

H. Frame roof opening - Identify location for

vent at the roof. Cut and/or frame opening per

Roof Framing Chart and Figure 24.

J. Install the storm collar - Install the storm

collar, supplied with the ﬂashing, over the

vent/ﬂashing joint. See Figure 26. Loosen the

storm collar screw. Slide collar down until it

meets the top of the ﬂashing. Tighten the ad-

justing screw. Apply non-combustible caulking

or mastic around the circumference of the joint

to provide a water tight seal.

Storm

Collar

Figure 23

F. Change vent direction to horizontal/inclined

run - At transition from or to a horizontal/in-

clined run, install the SV4.5E45 and SV4.5E90

elbows in the same manner as the straight vent

sections. The elbows feature a twist section to

allow them to be routed about the center axis

of their initial collar section to align with the

required direction of the next vent run element.

Twist elbow sections in a clockwise direction

only so as to avoid the possiblity of unlocking

any of the previously connected vent sections.

See Figure 23.

SV4.5E90

(90° Elbow)

7-5/8"

(194 mm)

Swivel Joint

(360° swivel)

4-13/16"

(122 mm)

SV4.5E45

(45° Elbow)

Swivel Joint

(360° swivel)

Framing Dimensions for Roof

Pitch C D

0/12 10-1/2 in. 10-1/2 in.

(267 mm) (267 mm)

6/12 10-1/2 in. 12 in.

(267 mm) (305 mm)

12/12 10-1/2 in. 17-3/4 in.

(267 mm) (451 mm)

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Figure 28 - Top Vent - STRAIGHT

Figure 29 - Top Vent - TWO 90 DEGREE ELBOWS

VERTICAL VENT FIGURES/TABLES

Note: Secure Vent (rigid vent pipe) is shown

in the ﬁgures; Secure Flex (ﬂexible vent pipe)

may also be used.

Note: It is very important that the horizontal/

inclined run be maintained in a straight (no

dips) and recommended to be in a slightly

elevated plane, in a direction away from the

ﬁreplace of 1/4 in. rise per foot (20 mm per

meter) which is ideal, though rise per foot run

ratios that are smaller are acceptable all the way

down to at or near level.

Note: SV4.5VF (Secure Vent), SF4.5VF (Secure

Flex) ﬁrestop/spacer must be used anytime vent

pipe passes through a combustible ﬂoor or ceil-

ing. SV4.5HF (Secure Vent), SF4.5HF (Secure

Flex)ﬁrestop/spacer must be used anytime vent

pipe passes through a combustible wall.

Note: Two 45 degree elbows may be used in

place of one 90 degree elbow. The same rise

to run ratios, as shown in the venting ﬁgures

for 90 elbows, must be followed if 45 degree

elbows are used.

AELBAT

VM MUMINI

umixaM

teef)sretem

sretem(

1*)503.0(5)25.1(

2)016.0(0

1.3(

3)419.0(5

56.4(

4)22.1(0

2.6(

V+V

.xaM)m3.81(teef06=H+

xaM)m2.6(teef02=

BELBAT

VM MUMINI HH+

mumixaM

teef)m(teef)m(

1)503.0(5)25.1(

2)016.0(01)1.3(

3)419.0(51)56.4(

4)22.1(02)2.6(

H+H

.xaM)m2.6(teef02=

V+V

H+H+

teef06=

.xaM)m3.81(

*Ceiling

Firestop/Spacer

(SV4.5VF)

*When using

Secure Flex, use

Firestop/Spacer

SF4.5VF

60 ft (18.3 m) Max

8 ft (2.4 m) Min

*Ceiling

Firestop/Spacer

(SV4.5VF) **Wall

Firestop/Spacer

(SV4.5HF)

*When using Secure Flex,

use Firestop/Spacer

SF4.5VF

**When using Secure

Flex, use Firestop/Spacer

SF4.5HF

*When developing chimney systems

with horizontal runs (H) that end with

a vertical run (V1), it is allowable to

use an elbow attached directly to the

top collar. Count the elbow attached

to the collar as 1 foot of (V) run.

*Ceiling

Firestop/Spacer

(SV4.5VF)

**Wall

Firestop/Spacer

(SV4.5HF)

**When using Secure

Flex, use Firestop/Spacer

SF4.5HF

*When using Secure Flex,

use Firestop/Spacer

SF4.5VF

Figure 30 - Top Vent - THREE ELBOWS

WARNING

Under no circumstances may

separate sections of concentric

flexible vent pipe be joined

together.

18 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Vertical

Rise

SV4.5E90

Elbow

Horizontal / Inclined Run SV4.5 HT

Termination

Firestop/Spacer

SV4.5L6/12/24/36/48

Vent Sections

Support Bracket Spacing

Every 5 ft (1.52 m)

See Figure 19 on page 13 for

vertical vent section support.

SV4.5 HT

Termination

Support

Brackets

Building

Support

Framing

Ceiling

Fireplace

Exterior

Wall

Exterior

Wall

TYPICAL HORIZONTAL VENT INSTALLATION

Figure 31

Secure Vent SV4.5 direct vent system components

are unitized concentric pipe components featuring

positive twist lock connection, (refer to Figure 21

on page 15). All of the appliances covered in this

document are ﬁtted with collars having locking

inclined channels. The dimpled end of the vent

components ﬁt over the appliance collar to create

the positive twist lock connection.

A. Plan the vent run -

Analyze the vent routing and determine the

types and quantities of sections required

4-1/2" (114 mm), 10-1/2" (267 mm), 22-1/2"

(572 mm), 34-1/2" (876 mm) and 46-1/2" (1181

mm) net section lengths are available. Plan the

vent lengths so that a joint does not occur at

the intersection of ceiling or roof joists. Make

allowances for elbows as indicated in Figure

23 on page 16. Maintain a minimum 1" (25

mm) clearance to combustibles on the vertical

sections. Clearances for the horizontal runs are;

3" (76 mm) on top, 1" (25 mm) on sides, and 1"

(25 mm) at the bottom.

B. Frame exterior wall opening -

Locate the center of the vent outlet on the exterior

wall according to the dimensions shown in Figure

10 on page 9. Cut and/or frame an opening,

10-1/2" x 12-1/8" (267 mm x 267 mm) inside

dimensions, about this center.

C. Frame ceiling opening - If the vertical route

is to penetrate a ceiling, use plumb line to locate

the center above the appliance. Cut and/or frame

an opening, 10-1/2" x 10-1/2" (267 mm x 267

mm) inside dimensions, about this center (refer

to Figure 19 on page 15 ).

D. Attach vent components to appliance - To

attach a vent component to the appliance collar,

align the dimpled end over the collar, adjust-

ing the radial alignment until the four locking

dimples are aligned with the inlets of the four

incline channels on the collar (refer to Figure

20 on page 15).

G. Support the vertical run sections -

See Section E on page 15.

Push the vent component against the collar until it

fully engages, then twist the component clockwise,

running the dimples down and along the incline

channels until they seat at the end of the channels.

The unitized design of the Secure Vent compo-

nents will engage and seal both the inner and

outer pipe elements with the same procedure.

Sealant and securing screws are not required.

E. Attach vent components to each other

- Other vent sections may be added to the pre-

viously installed section in accordance with the

requirements of the vent tables. To add another

vent component to a length of vent run, align the

dimpled end of the component over the inclined

channel end of the previously installed section,

adjusting the radial alignment until the four lock-

ing dimples are aligned with the inlets of the four

incline channels of the previous section. Push

the vent component against the previous section

until it fully engages, then twist the component

clockwise running the dimples down and along

the incline channels until they seat at the end of

the channels.This seating position is indicated

by the alignment of the arrow and dimple as

shown in Figure 21 on page 15.

F. Install ﬁrestop/spacer at ceiling -

When using Secure Vent, use SV4.5VF ﬁrestop/

spacer at ceiling joists; when using Secure

Flex, use SF4.5VF ﬁrestop/spacer. If there is

living space above the ceiling level, the ﬁrestop/

spacer must be installed on the bottom side of

the ceiling. If attic space is above the ceiling,

the ﬁrestop/ spacer must be installed on the

top side of the joist. Route the vent sections

through the framed opening and secure the

ﬁrestop/spacer with 8d nails or other appropriate

fasteners at each corner.

I. Continue installation of horizontal/inclined

sections - Continue with the installation of the

straight vent sections in horizontal/inclined run

as described in Step E. Install support straps

every 5 ft. (1.52 m) along horizontal/inclined

vent runs using conventional plumber’s tape.

See Figure 31. It is very important that the

horizontal/inclined run be maintained in a

straight (no dips) and recommended to be in

a slightly elevated plane, in a direction away

from the ﬁreplace of 1/4" rise per foot (20 mm

per meter) which is ideal, though rise per foot

run ratios that are smaller are acceptable all the

way down to at or near level. Use a carpenter’s

level to measure from a constant surface and

adjust the support straps as necessary.

Both of these horizontal vent systems terminate

through an outside wall. Building Codes limit or

prohibit terminating in speciﬁc areas. Refer to

Figure 6 on page 7 for location guidelines.

Figure 31, and Figures 34 to 36 on pages 20

and 21 and their associated Horizontal Vent

Table illustrate the various horizontal venting

conﬁgurations that are possible for use with

these appliances. Secure Vent pipe applications

are shown in these ﬁgures; Secure Flex pipe

may also be used. A Horizontal Vent Table sum-

marizes each system’s minimum and maximum

vertical and horizontal length values that can be

used to design and install the vent components

in a variety of applications.

HORIZONTAL (OUTSIDE WALL)

TERMINATION SYSTEM

H. Change vent direction - At transition from or

to a horizontal/inclined run, install the SV4.5E45

and SV4.5E90 elbows in the same manner as

the straight vent sections. The elbows feature a

twist section to allow them to be routed about the

center axis of their initial collar section to align

with the required direction of the next vent run

element. Twist elbow sections in a clockwise

direction only so as to avoid the possiblity

of unlocking any of the previously connected

vent sections. See Figure 23.

Remember to maintain 1" (25 mm) clearance

to combustibles, framing members, and attic

or ceiling insulation when running vertical

chimney sections.

NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

Firestop/Spacer (SV4.5HF) shown

on the exterior side of the wall. It

may also be installed on the

interior side. SV4.5 HT

Termination

10-1/2"

(267mm)

(178)

5-1/8"

(130 mm)

12-1/8"

(308 mm)

Note: Centerline of Vent Piping is

NOT the Same as the Centerline of

the Framed Opening.

6 to 48 inch Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

See Figure 4 on page 5

for Min. Distance to Base

of Appliance.

Base of Appliance

(76 mm)

(25.4 mm)

Adapter

SV4.5RCH

IMPORTANT: The vent termination is

hot while in operation and for a period

of time following use of the ﬁreplace.

To prevent contact with hot surfaces,

we recommend the use of a Termination

Guard. This can be purchased at your

local dealer.

Horizontal terminations have been designed to perform in a wide range of weather condi-

tions. Our terminations meet or exceed industry standards.

When selecting the locations of your horizontal terminations, do not place the termination

where water from eaves and adjoining rooﬂines may create a heavy ﬂow of cascading water

onto the termination cap. If the cap must be placed where the possibility of cascading water

exists, it is the responsibility of the builder to direct the water away from the termination

cap by using gutters or other means.

Take care to carefully follow the installation instructions for the termination, including the

use of silicone caulking where required.

Figure 33

Siding

Stucco 1 1/4 in (32 mm)

Maximum Recess of

Either Square Termination into

Exterior Finishing Material

Exterior Surface of

Framing

5 in. to 9 1/4 in.

(127 to 235 mm)

Exterior Surface of Siding

Minimum wall thickness

5 in. (127 mm)

Interior Surface of

Finished Wall

Maximum wall thickness

9 1/4 in.(235 mm)

SV4.5HT

Square

Termination

Maximum Extent of

Vent Run Sections

Relative to Exterior

Surface of Framing

Last Vent Section. Use

Telescopic Vent

Section (SV4.5LA), If

Necessary

Adapter

SV4.5RCH

(Provided With The

Termination)

SV4.5HT

Square Termination

Venting Connection and Exterior Wall Recessing of the

Horizontal Square Termination (SV4.5HT).

Note: Venting terminals shall not be recessed into

a wall or siding.

It is important to maintain the required clear-

ances to combustibles: 1" (25 mm) at all sides

for all vertical runs; and 3" (76 mm) at the top,

1" (25 mm) at sides, and 1" (25 mm) at the

bottom for all horizontal/inclined runs

J. Assemble vent run to exterior wall - If not

previously measured, locate the center of the

vent at the exterior wall. Prepare an opening as

described in Step B. Assemble the vent system

to point where the terminus of the last section

is within 5 in. (127 mm) to 9-1/4 in. (235 mm)

inboard of the exterior surface to which the

termination is to be attached, see Figure 33.

If the terminus of the last section is not within

this distance, use the telescopic vent section

SV4.5LA, as the last vent section. For wall

thicknesses greater than that shown in Figure

33, refer to Table 7 on page 20. This table lists

the additional venting components needed (in

addition to the termination and adapter) for a

particular range of wall thicknesses.

K. Attach termination adapter - Attach the

adapter (adapter - SV4.5RCH - provided with the

termination) to the vent section or telescoping

vent section), elbow or appliance collar as shown

in Figure 32 in the same manner as any SV4.5

vent component (refer to Step E).

L. Install Firestop/Spacer at exterior wall

- When using the square termination, install

SV4.5HF (Secure Vent), SF4.5HF (Secure Flex)

Firestop/Spacer over the opening at the exterior

side of the framing, long side up, with the 3 inch

spacer clearance at the top as shown in Figure

32, and nail into place. (The Firestop/Spacer

may also be installed over the opening at the

interior side of the framing).

1. Install the square termination (SV4.5HT-2)

- For the last step , from outside the exterior

wall, slide the collars of the termination onto

the adapter (the outer over the outer and the

inner inside the inner) until the termination seats

against the exterior wall surface to which it will

be attached. Orient the housing of the termina-

tion with the arrow pointed upwards. Secure

the termination to the exterior wall.

Orient the housing of the termination with the

arrow pointed upwards. Secure the termination

to the exterior wall.

SFHRK Snorkel Cap –The snorkel cap is

designed to be ﬁtted into a basement window

box. The SFHRK cap is for use with ﬂex vent

pipe. The SV4.5HRK14 and SV4.5HRK36 are

for rigid vent pipe.

Installing the Square Horizontal Termination (SV4.5HT-2).

Figure 32

20 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.

**Wall Firestop/Spacer

(SV4.5HF)

**When using Secure

Flex, use Firestop/Spacer

SF4.5VF

*Ceiling

Firestop/Spacer

(SV4.5VF)

*When using Secure Flex,

use Firestop/Spacer

SF4.5HF

7ELBAT

llaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneVllaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneV llaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneV llaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneVllaWroiretxEsuoiraVrofderiuqeRstnenopmoCgnitneV

tiKnoitanimreTerauqSehTgnisUnehW,sessenkcihTtiKnoitanimreTerauqSehTgnisUnehW,sessenkcihT tiKnoitanimreTerauqSehTgnisUnehW,sessenkcihT tiKnoitanimreTerauqSehTgnisUne